Configuration requried for 4 port ISDN S/T Interface card as backup link

Dear All,
I have ISDN BRI 4 lines Interface card installed in my company router cisco 2821, I want to configure all 4 BRI lines as an backup link of 512Kbps with same ISP which is directly connected on Serial0/2/0 with 1mbps bandwidth. If my Serial link become down. ALL 4 BRI group dail same ISP with full loaded 512kbps bandwith link.
Router IOS detail c2800nm-ipbasek9-mz.124-15.T5.bin
and I have no idea how to impelement in real senerio.
if any one using same senerio in his live enviroment please send me configration....!
waiting you reply....

Respected Sir,
Thanks for your advise. But This is very helpfull forum of cisco where cisco highly professional persons help their juniors sitting allaround the world, therefore as a junior I have posted my problem here someone give me guide line. How to configure it...?
Because no one is perfect in whole world everyone is trying to learn more and more in his field, so this is my humbly request if you looking into this matter and help me out.
I will be very thankfull to you.
regards

Similar Messages

Drivers for quad port Intel Pro1000 GT network card

Hi folks,
just trying to get this card to work on our MAC. It doesn't come with any drivers and the intel site directs you to Small Tree for their driver. This only works on Small Tree branded products, anyone solved this problem? We are running OSX10.5 Leopard.
Any help appreciated.
Gra

Resolved the problem. You have to have a small tree card!

Understanding ISDN BRI Voice Interface Cards

Hi all,
I was wondering about the VIC-2BRI-NT/TE VIC:
In NT mode, what kind of BRI interface I can connect to it? Is it a BRI S/T interface (The device that is been connected to it)?
I got a PBX that has BRI S/T interfaces... can i connect them to this card (while in NT state)?
Will DID work in this case?
Thanks,
Edy.

Hi Malleyne,
Thanks for the response.
I looked at the document, and I found my answers indeed. The only way to understand from the document (or any other on the net) that it will connect to an S/T interface is by the fact is says it acts as a NT1 device. Couldn't they make it more simple? :)
Thanks again,
Edy.

Configuration doc for Report painter

Hi Friends,
Can any one send configuration document for Report painter?
[email protected]
Regards
Babu

hi
find this link
http://www.virtuosollc.com/PDF/Get_Reporter.pdf

Configuration Template for SRP 521W

Hello all,
Does anyone have a recommnedation for creating a configuration template for the SRP521W? I can use the Admin-->Backup Config to get a xxx.cfg file, but I cannot edit it with notepad++.
Also, i know the config can be view via view-source:http://ipaddr/admin/config.xml, but how would I load a modified copy of this back to the router?
Thanks in advance for your time!
Philip

Hi Philip,
You can load XML configurations on to the SRP using a number of different methods.
Firstly, make sure that your XML is properly formatted as follows. Configuration files can include as much or as little configuration as you need.
<?xml version="1.0"?>
Add your configuration here
Provisioning Methods
1. Resync URL
You can use the resync URL to command the SRP to collect a new configuration from a specified location. The SRP can use TFTP, HTTP or HTTPS to collect the defined configuration. Once you have created your configuration file and loaded it to a TFTP or web server, construct a URL as follows and paste it in to your browser.
http://:/admin/resync?&xuser=admin&xpassword=
For example:
http://192.168.15.1/admin/resync?tftp://192.168.15.100/myconfig.xml&xuser=admin&xpassword=admin
2. Provisioning URL configuration
As an alternative to the above, it is also possible to configure the SRP500 with a provisioning URL via the web GUI. In this case, take the configuration file URL and use it configure the "Profile Rule" configuration field, which may be found on the Voice > Provisioning page.
3. Push URL
Use an application like curl to post the XML file directly to the SRP IP address. For example:
curl -k -d @myconfig.xml http://192.168.15.1/admin/config.xml&xuser=admin&xpassword=admin

Measurement Computing USB-SSR24 error 42 Digital Port not configured correctly for requested operation

Using LV 2012 and ULx 2.02 LV driver:
LV is throwing an error 42 (Digital Port not configured correctly for requested operation) from the ULx write VI but only on PortCH. All my configurations are correct on the hardware and Instacal tests the ports OK. I've reinstalled everything and still see the same issue.
Since PortA is configured identical to PortCH, and PortA is functioning fine, I'm stumped. This is occuring on two different SSR24 DAQs so I don't think it's the hardware, plus I've already mentioned that the Instacal isn't having a problem with it.
I've attached my VI I'm using for debug.
Jeff
Attachments:
test of Wilmington.vi ‏19 KB

I worked with Measurement Computing and they agreed that there is a bug with certain DI/DO configurations. There are a possible 16 different DI/DO configurations with the hardware and apparently mine (PortA - DO, PortB- DI, PortCL-DI, and PortCH-DO will throw this error for PortCH. I'm currently using .net calls to work around the issue until the ULx driver is updated. I'll post that when I see it. Attached are the .net VI's that I'm using for simple static IO.
Attachments:
USB SSR DOT NET Write Bit.vi ‏20 KB
USB SSR DOT NET Read Bit.vi ‏21 KB

Cisco 4-Port ISDN-BRI Network Module

Cisco 4-Port ISDN-BRI Network Module
what does the BRI mean?
I have this module in a 2600 series router. Can it be used for basic LAN connection (like a hub)?

First, to answer your question: No, you cannot.
ISDN is a Telco technology and protocol suite.
"BRI" stands for "Basic Rate Interface," also described as "2B+D" for two Bearer channels and a "D" channel, which is used for control signaling in some configurations, and additional bandwidth in others.
Max throughput is either 128K (2 X 56K or 64Kbps per channel) or 144Kbps (2B+16K that may be available in the D channel depending on your config.
ISDN requires an intermediate telco-style switch between the clients and can't be used back-to-back directly.
Good Luck
Scott

Configure SSO for ITS to R/3 using SNC/Kerberos

Our R/3 systems had been configured for SSO using SNC and Kerberos for awhile now. We now have a requirement to configure SSO between ITS and R/3. Since our R/3 env. has been using kerberos library, we won't be able to use SAP Cryptographic library. I had modified the registry, environment and services in itsadmin to point to the kerberos library and principal names for agate and r/3 servers as described in SNC User Guide; also, I updated table SNCSYSACL with the Agate SNC name. That seems to work fine. From the trace file, it recognized GSS-API library for Kerberos and the SNC name for Agate. However, when I tried to logon to R/3 from ITS, I still am being prompted with the logon screen to enter my SAP account/password.
I found several whitepapers and documentations stating that ITS does support Kerberos for SSO but I couldn't find any procedure on how to implement it. Following is the error I'm getting from the sapbasis.trc file but I can't find any document on this error:
=====================================================
[Thr 5284] SncInit(): Initializing Secure Network Communication (SNC)
[Thr 5284]       PC with Windows NT (mt,ascii,SAP_UC/size_t/void* = 8/32/32)
[Thr 5284] SncInit(): Trying environment variable SNC_LIB as a
      gssapi library name: "C:\WINNT\system32\gsskrb5.dll".
[Thr 5284]   File "C:\WINNT\system32\gsskrb5.dll" dynamically loaded as GSS-API v2 library.
[Thr 5284]   The internal Adapter for the loaded GSS-API mechanism identifies as:
Internal SNC-Adapter (Rev 1.0) to Kerberos 5/GSS-API v2
[Thr 2888] Sun Jan 15 22:44:59 2006
[Thr 2888] <<- ERROR: SncSetParam()==SNCERR_PARAM_DENIED
[Thr 2888] *** WARNING => NO Domain! domain==NULL means: No domain at all within the cookie. [sapss1_loctr 333]
[Thr 2888] Sun Jan 15 22:45:29 2006
[Thr 2888] *** WARNING => NO Domain! domain==NULL means: No domain at all within the cookie. [sapss1_loctr 333]
=====================================================
Does anyone know what am I missing? Any help is greatly appreciated.
Thank you!
Diem

Hi Markus,
I also just installed/configured PAS for LDAP authentication using the "PAS for External Authentication Mechanisms" documentation. I think the domain problem probably due to not having the external authentication mechanism install (in this case - PAS). Does that sound right to you?
I tried both options for ~extid_type parameter = "LD" and "UN". I added the DN information to table USREXTID when ~extid_type="LD" but both options gave me error of "LDAP authentication failed". I increased the trace level for sapextaut.trc but I don't see enough detail information. Following are the errors/data from the trace file. Can you please let me know how I can tell what string is being passed for authentication?
I'm quite sure the LDAP host and port data is correct since we've been using the same information for the SAP LDAP connector and we've been using our LDAP connector between MS AD and R/3 for a long time without any problem.
To logon to R/3 through ITS, I entered the AD account (CN attribute in AD) when I got the errors.
Thank you very much for all your help.
Diem Tran
Trace:
=====================================================
2006-01-18T01:39:30.734 p001688 t4992 s0158B4E8 [sapextauth, 437]: W sapextauth: PAS session begins...
2006-01-18T01:39:30.734 p001688 t4992 s0158B4E8 [sapextauth, 456]:     sapextauth: SncNameR3 is:    "p:na1adm/[email protected]"
2006-01-18T01:39:30.734 p001688 t4992 s0158B4E8 [sapextauth, 462]:     sapextauth: SncNameAGate is: "p:[email protected]"
2006-01-18T01:39:30.750 p001688 t4992 s0158B4E8 [sapextauth, 468]:     sapextauth: SNC_LIB is:      "C:\WINNT\system32\gsskrb5.dll"
2006-01-18T01:39:30.750 p001688 t4992 s0158B4E8 [sapextauth, 568]:     sapextauth: XGatConnectSession leaving....
2006-01-18T01:39:30.750 p001688 t4992 s0158B4E8 [sapextauth, 616]:     sapextauth: XGatHandleLogin called....
2006-01-18T01:39:30.750 p001688 t4992 s0158B4E8 [sapextauth, 976]:     sapextauth: Entering XGatHandleLogin with LDAP...
2006-01-18T01:39:30.750 p001688 t4992 s0158B4E8 [sapextauth, 993]: W Either ~login or ~password missing, returning XGDKRCloginrequired.
2006-01-18T01:39:50.281 p001688 t4992 s00000000 [sapextauth, 398]:     sapextauth: XGatEventOpenSession called...
2006-01-18T01:39:50.281 p001688 t4992 s0158B4E8 [sapextauth, 616]:     sapextauth: XGatHandleLogin called....
2006-01-18T01:39:50.281 p001688 t4992 s0158B4E8 [sapextauth, 976]:     sapextauth: Entering XGatHandleLogin with LDAP...
2006-01-18T01:39:50.296 p001688 t4992 s0158B4E8 [sapextauth, 1059]:     sapextauth: LDAP port ist 389
2006-01-18T01:39:50.296 p001688 t4992 s0158B4E8 [sapextauth, 1261]: E sapextauth: LDAP authentication failed.
2006-01-18T01:39:50.296 p001688 t4992 s0158B4E8 [sapextauth, 1277]: E sapextauth: Wrong try for user Tran_Diem
2006-01-18T01:39:59.140 p001688 t4992 s00000000 [sapextauth, 398]:     sapextauth: XGatEventOpenSession called...
2006-01-18T01:39:59.156 p001688 t4992 s0158B4E8 [sapextauth, 616]:     sapextauth: XGatHandleLogin called....
2006-01-18T01:39:59.156 p001688 t4992 s0158B4E8 [sapextauth, 976]:     sapextauth: Entering XGatHandleLogin with LDAP...
2006-01-18T01:39:59.156 p001688 t4992 s0158B4E8 [sapextauth, 1059]:     sapextauth: LDAP port ist 389
2006-01-18T01:39:59.156 p001688 t4992 s0158B4E8 [sapextauth, 1261]: E sapextauth: LDAP authentication failed.
2006-01-18T01:39:59.156 p001688 t4992 s0158B4E8 [sapextauth, 1277]: E sapextauth: Wrong try for user Tran_Diem
=======================================================

Configuration Guide for 6248 and 5548 and VNX 5500

Hi,
Need help here to configure the FCoE Uplink + Ethernet Uplink in Port channel
Following is the connectivity details from 6248, 5548 and VNX5500.
I have configured Port Channel in following way on Both Fabric Interconnect
After Configuring above things I am getting following Faults on Servers
For NetApp3240 ENM source pinning failed, I have allowed VLAN ID 21 in Uplink manager then too this Link state is not showing UP and Same thing go for both FC_vHBA
Kinldy help me to configure the setup
-Amit

Below is the ouput for two commands "show run int port-channel membership" and "sh int port-channel "
===========================================================================
primary# sh run int po2 membership
!Command: show running-config interface port-channel2 membership
!Time: Wed Feb 25 07:55:31 2009
version 5.2(1)N1(1b)
interface port-channel2
description ***Link to FI-A in R17***
switchport mode trunk
switchport trunk allowed vlan 12-13,21,101-600
spanning-tree port type edge
spanning-tree bpdufilter enable
interface Ethernet1/3
description ***Link to FI-A in R17***
switchport mode trunk
switchport trunk allowed vlan 12-13,21,101-600
channel-group 2 mode active
interface Ethernet1/4
description ***Link to FI-A in R17***
switchport mode trunk
switchport trunk allowed vlan 12-13,21,101-600
channel-group 2 mode active
interface Ethernet1/5
description ***Link to FI-B in R18***
switchport mode trunk
switchport trunk allowed vlan 12-13,21,101-600
channel-group 2 mode active
===========================================================================
primary# sh run int po3 membership
!Command: show running-config interface port-channel3 membership
!Time: Wed Feb 25 07:57:14 2009
version 5.2(1)N1(1b)
interface port-channel3
description ***Link to FI-B in R18***
switchport mode trunk
switchport trunk allowed vlan 12-13,21,101-600
spanning-tree port type edge
spanning-tree bpdufilter enable
interface Ethernet1/8
description ***Link to FI-B in R18***
switchport mode trunk
switchport trunk allowed vlan 12-13,21,101-600
channel-group 3 mode active
interface Ethernet1/9
description ***Link to FI-B in R18***
switchport mode trunk
switchport trunk allowed vlan 12-13,21,101-600
channel-group 3 mode active
interface Ethernet1/10
description ***Link to FI-B in R18***
switchport mode trunk
switchport trunk allowed vlan 12-13,21,101-600
channel-group 3 mode active
===========================================================================
primary# sh int po2
port-channel2 is up
Hardware: Port-Channel, address: 002a.6a0a.4caa (bia 002a.6a0a.4caa)
Description: ***Link to FI-A in R17***
MTU 1500 bytes, BW 30000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is trunk
full-duplex, 10 Gb/s
Input flow-control is off, output flow-control is off
Switchport monitor is off
EtherType is 0x8100
Members in this channel: Eth1/3, Eth1/4, Eth1/5
Last clearing of "show interface" counters never
30 seconds input rate 504 bits/sec, 0 packets/sec
30 seconds output rate 2256 bits/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
    input rate 456 bps, 0 pps; output rate 656 bps, 0 pps
RX
    22208045 unicast packets 747374 multicast packets 27634234 broadcast packets
    50589653 input packets 49083144072 bytes
    21411174 jumbo packets 0 storm suppression bytes
    0 runts 0 giants 0 CRC 0 no buffer
    0 input error 0 short frame 0 overrun   0 underrun 0 ignored
    0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
    0 input with dribble 0 input discard
    0 Rx pause
TX
    2801196 unicast packets 353162904 multicast packets 549464 broadcast packets
    356513564 output packets 25978572978 bytes
    101325 jumbo packets
    0 output errors 0 collision 0 deferred 0 late collision
    0 lost carrier 0 no carrier 0 babble 0 output discard
    0 Tx pause
35 interface resets
===========================================================================
primary# sh int po3
port-channel3 is up
Hardware: Port-Channel, address: 002a.6a0a.4caf (bia 002a.6a0a.4caf)
Description: ***Link to FI-B in R18***
MTU 1500 bytes, BW 30000000 Kbit, DLY 10 usec
reliability 48052/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is trunk
full-duplex, 10 Gb/s
Input flow-control is off, output flow-control is off
Switchport monitor is off
EtherType is 0x8100
Members in this channel: Eth1/8, Eth1/9, Eth1/10
Last clearing of "show interface" counters never
30 seconds input rate 104 bits/sec, 0 packets/sec
30 seconds output rate 1704 bits/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
    input rate 448 bps, 0 pps; output rate 1.08 Kbps, 0 pps
RX
    9070 unicast packets 288523 multicast packets 143322 broadcast packets
    440915 input packets 72677230 bytes
    7 jumbo packets 0 storm suppression bytes
    0 runts 0 giants 36 CRC 0 no buffer
    2161727821137838086 input error 0 short frame 0 overrun   0 underrun 0 ignored
    0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
    0 input with dribble 0 input discard
    0 Rx pause
TX
    62914 unicast packets 74425404 multicast packets 14434365 broadcast packets
    88922683 output packets 7182753461 bytes
    14 jumbo packets
    0 output errors 0 collision 0 deferred 0 late collision
    0 lost carrier 0 no carrier 0 babble 0 output discard
    0 Tx pause
17 interface resets
===========================================================================
secondary# sh run int po2 mem
!Command: show running-config interface port-channel2 membership
!Time: Wed Feb 25 07:56:41 2009
version 5.2(1)N1(1b)
interface port-channel2
description ***Link to FI-A in R17***
switchport mode trunk
switchport trunk allowed vlan 12-13,21,101-600
spanning-tree port type edge
spanning-tree bpdufilter enable
interface Ethernet1/8
description ***Link to FI-B in R18***
switchport mode trunk
switchport trunk allowed vlan 12-13,21,101-600
channel-group 2 mode active
interface Ethernet1/9
description ***Link to FI-B in R18***
switchport mode trunk
switchport trunk allowed vlan 12-13,21,101-600
channel-group 2 mode active
interface Ethernet1/10
description ***Link to FI-B in R18***
switchport mode trunk
switchport trunk allowed vlan 12-13,21,101-600
channel-group 2 mode active
===========================================================================
secondary# sh run int po3 mem
!Command: show running-config interface port-channel3 membership
!Time: Wed Feb 25 07:58:30 2009
version 5.2(1)N1(1b)
interface port-channel3
description ***Link to FI-B in R18***
switchport mode trunk
switchport trunk allowed vlan 12-13,21,101-600
spanning-tree port type edge
spanning-tree bpdufilter enable
interface Ethernet1/3
description ***Link to FI-A in R17***
switchport mode trunk
switchport trunk allowed vlan 12-13,21,101-600
channel-group 3 mode active
interface Ethernet1/4
description ***Link to FI-A in R17***
switchport mode trunk
switchport trunk allowed vlan 12-13,21,101-600
channel-group 3 mode active
interface Ethernet1/5
description ***Link to FI-B in R18***
switchport mode trunk
switchport trunk allowed vlan 12-13,21,101-600
channel-group 3 mode active
===========================================================================
secondary# sh int po2
port-channel2 is up
Hardware: Port-Channel, address: 002a.6a0a.4d6f (bia 002a.6a0a.4d6f)
Description: ***Link to FI-A in R17***
MTU 1500 bytes, BW 30000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is trunk
full-duplex, 10 Gb/s
Input flow-control is off, output flow-control is off
Switchport monitor is off
EtherType is 0x8100
Members in this channel: Eth1/8, Eth1/9, Eth1/10
Last clearing of "show interface" counters never
30 seconds input rate 1752 bits/sec, 0 packets/sec
30 seconds output rate 1016 bits/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
    input rate 832 bps, 0 pps; output rate 496 bps, 0 pps
RX
    76009142 unicast packets 544440 multicast packets 228999 broadcast packets
    76782581 input packets 146179423660 bytes
    68566412 jumbo packets 0 storm suppression bytes
    0 runts 0 giants 0 CRC 0 no buffer
    0 input error 0 short frame 0 overrun   0 underrun 0 ignored
    0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
    0 input with dribble 0 input discard
    0 Rx pause
TX
    192711593 unicast packets 154928956 multicast packets 31420967 broadcast packets
    379061516 output packets 385914168860 bytes
    179761364 jumbo packets
    0 output errors 0 collision 0 deferred 0 late collision
    0 lost carrier 0 no carrier 0 babble 0 output discard
    0 Tx pause
24 interface resets
===========================================================================
secondary# sh int po3
port-channel3 is up
Hardware: Port-Channel, address: 002a.6a0a.4d6a (bia 002a.6a0a.4d6a)
Description: ***Link to FI-B in R18***
MTU 1500 bytes, BW 30000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is trunk
full-duplex, 10 Gb/s
Input flow-control is off, output flow-control is off
Switchport monitor is off
EtherType is 0x8100
Members in this channel: Eth1/3, Eth1/4, Eth1/5
Last clearing of "show interface" counters never
30 seconds input rate 456 bits/sec, 0 packets/sec
30 seconds output rate 1784 bits/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
    input rate 456 bps, 0 pps; output rate 912 bps, 0 pps
RX
    75986748 unicast packets 490267 multicast packets 124569 broadcast packets
    76601584 input packets 146159548726 bytes
    68566413 jumbo packets 0 storm suppression bytes
    0 runts 0 giants 0 CRC 0 no buffer
    0 input error 0 short frame 0 overrun   0 underrun 0 ignored
    0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
    0 input with dribble 0 input discard
    0 Rx pause
TX
    192585042 unicast packets 190939131 multicast packets 13399201 broadcast packets
    396923374 output packets 386206869311 bytes
    179761514 jumbo packets
    0 output errors 0 collision 0 deferred 0 late collision
    0 lost carrier 0 no carrier 0 babble 0 output discard
    0 Tx pause
24 interface resets
===========================================================================
We have removed vPC configuration as we are facing same problem as i said in my previous post
id     Port        Status Consistency Reason                     Active vlans
2      Po2         up     failed      vpc port channel           -
                                      mis-config due to vpc
                                      links in the 2 switches
                                      connected to different
                                      partners
Do let me know if anything else is required from my end
-amit

SG300-20 configure 1 ip pr port

We got 1 customer that would like us to configure a system based on SG300-20 linked up with an SG300-10SFP using trafficshaping ingress and egress limited to 40mbit.
This part of the case is solved using ingress/egress 40960 with an burtlimit a bith higher.
But he also wants each firewall configured on the net to only be able to have 1 ip on that spesific port.
this is an owner of a building that rents out to other companies. Each comapny is assinged a port on the SG300-20 and has theire own ip (ie 100.100.12.34) all of them are part of a /26 net and would use the same Gateway.
Is this possible ?
that the company assigned to ie port 14 in switch 1 only can use 100.100.12.34/26 gw 100.100.12.1 and if they change to 100.100.12.36 it will not work. This to prevent the endusers from changing and fu...g up the net for the rest :-)
and on port 16 on switch 1 they can only use 100.100.12.36/26 with gw 100.100.12.1
thnsk for any input
switches are in layer2 mode , but nothing is in production yet so i can change ot layer3 if thats what it takes.
regard
Thomas

Hi Thomas, your concept sounds correct.
This is how this works
Assuming your topology is this-
Internet -> Router -> Core switch (no client/customer) -> Access switch -> Client/customer
For argument sake, your uplink from access switch is port 18 which connects to port 18 of the core switch
Problem statement-
On access switch, your desire is to have a client or customer connect to the switch using a specific MAC address and IP address and no other
Possible solutions-
Dynamic ARP inspections statically MAPS and IP address to a MAC address, any connection using the same MAC but different IP will be dropped and any connection using the same IP but different MAC will be dropped
Create an access list to permit only the desire IP address on the INGRESS port and block any other traffic to that port
Solution work flow-
Enable dynamic ARP inspection
Security -> ARP inspection -> Properties -> Enable
Enable trusted interfaces - These interfaces will allow any traffic and not subject to your inspection list. Untrusted is subject to the inspect list
Security -> ARP Inspection -> Interface Settings -> Edit interfaces as desired
Build your inspection table
Security -> ARP inspection -> ARP access control -> Add ->
-Control name is an arbitrary value, it is a description
-IP address is the IP you want in the database
-MAC address is the binding to the IP address for the switch to look up in the data
If DAI is too stringent for you, you may create an access list as an alternative solution
Access Control -> IPV4 based ACL -> Add
-ACL Name is what you want to call it, a description -> Apply
Next define the access list by going to IPV4 ACE bu click IPV4-based ACE -> Add
-Priority is an ordering system, you should structure your rules in an order for the switch to look up the rules
-Action permit or deny, in your case you want to permit
-Protocol will be IP (all traffic)
-Source IP address will be your host connection 100.100.12.34
-Wildcard mask will be 0.0.0.0 (this is a single host wild card)
-Destination will be Any
Click apply
Once the access list is built, it then gets bound to an interface. The interface must be the interface where the traffic goes to and not leaving
Access Control -> ACL Binding (port)
-Check box for the port your customer/client connects
-Interface is where the customer/client connects to the switch
-Check box for Select IPV4-Based ACL
-Default action is Deny Any
-Apply
With this completed correctly, only your IP for all traffic will connect to that port and any other IP will not be allowed, will discard if connection through that same port.
-Tom
Please mark answered for helpful posts

What are the steps requried for r/3 to xi and xi to r/3 configuraiton ?

Hi Experts
What are the steps requried for r/3 to pi 7.1 and pi 7.1 to r/3 configuraiton ?
Thanks & Regards
G.Praveen Kumar
Edited by: praveen.tecnics on Apr 1, 2009 4:51 PM

In case of RFC already signature will be defined in R/3 itself the same will there in PI too after importing .
In case of idoc also you just need to import for the usage and can be used depending on scenario
if the above answers doesnt suite your question then can you post query in detailed way
In case of Configurations
RFC destination types differ for idoc and RFC
in idoc SM59 Type 3 conection you need to create
for RFC you need Type T connection
HTH
Rajesh

Sql developer configuration settings for R12.1.1 vision instance

I have successfully installed oracle r12.1.1 vision instance in my laptop.
I want to connect to database, where can I get the details of hostname, port and sid details for vision instance to configure in SQL developer
Thanks.

Hostname - Your machine IP or Name
for SID PORT - Please see tnsnames.ora file in your oracle home/network/admin
Tnsnames.ora - Oracle FAQ
AppsMAsti
Sharing is Caring

UWL Configuration Document for EP 7.0

Dear all,
We are on EP 7 and trying to configure the UWL. I have a few documentation on the configuration of UWL (not sure whether is works for EP 7). When i try to Registering System Item Types with the UWL, i can see the following option which is different from EP 6.
AdHocSystem - AdHocWorkflowConnector
ActionInbox - ActionInboxConnector
We are using webdynpro and JCO connection. Therefore does it still require the system landscape? Anyone have the UWL configuration document for EP 7?
Thanks,
Regards,
Bryan

We need to create ITS settings in system object
Select Internet Transaction Server in the Property Category drop list from Ur system object
Give details as below
ITS Description: Give description
ITS Host Name: bs3q01.mycompany.com:8001
This information can be found under transaction code SMICM. Choose menu path GoTo  Services and you can find the hostname and port for the HTTP record.
ITS Path: /sap/bc/gui/sap/its/webgui
ITS Protocol: HTTP
Save
And also u need to activate these services
Goto Ur backend system goto SICF execute -- default_host sap bc gui sap its webgui
Right click and activate services
Regards
Krishna.

CSS11501 - URL Redirect for Multiple Servers For Both Ports 80 & 443

Can the CSS rules be configured such that it can be used to direct requests to different Web servers based upon,
URL path?
For Both Ports 80 & 443/HTTPS (with SSL Certificate running on the back-end servers)
For example:
http://app.ti.com/path1/file.html goes to Web servers A & B -> old servers
https://app.ti.com/path1/file.html goes to Web servers A & B -> "
http://app.ti.com/path2/file.html goes to Web servers C & D -> new servers
https://app.ti.com/path2/file.html goes to Web servers C & D -> "
We're trying to understand what are plans are for a phased migration from old site to new site, and if it requires new URLs ???
Fort port 443, since the CSS is load balancing SSL encrypted traffic, is the means that the CSS can’t look at URL thus this is not possible?
Please help, thanks.

Hi Martin,
1) Clients are using http://domain/, thus I need to define url "//domain/.." as you have stated.
2) I'm still waiting for the "actual" URL paths from the application team in order to decide which method to use - Regexp vs URLQ definition - to begin testing.
I know I have limited memory resource (as listed below) & will try not to make it complicated:
System Resources for CSS501-SCM-INT:
Installed Memory:   268,435,456 (256 MB)
Free Memory:        135,414,448 (129 MB) ****
CPU:                0% (5Sec)     1% (1Min)     0% (5Min)
Buffer Statistics:
Buffer Pool: 0
   Size:2048 Total:3072 Available:2792 Failures: 0 Low Buffer Count: 2748
Buffer Pool: 1
   Size:2048 Total:3072 Available:2800 Failures: 0 Low Buffer Count: 2800
Buffer Pool: 2
   Size:2048 Total:2048 Available:1956 Failures: 0 Low Buffer Count: 1900
Thanks Martin, you've been a big help!
Diane Ly

How do I configure SPA8800 for a Viking FBI-1A?

I am working with a customer who has had a phone system failure. We're trying to replace the old Asterisk system that had a hardware interface card with a newer system and use an SPA8800 adapter (since I have that in stock and didn't have the hardware card in stock) to provide dialtone to the faxe machines and connect to the overhead paging system. The problem I'm having is with the overhead paging system.
The system is a Viking FBI-1A (http://www.vikingelectronics.com/products/view_product.php?pname=FBI-1A#), which can be configured either in Trunk Mode or Paging Mode. In Paging Mode and connected to one of the FXS ports on the SPA8800, the paging system basically immediately "picks up" the FXS line and blares dial-tone over the overhead speakers, staying continuously off-hook, even after the "you left the phone of the hook, dummy" error beep starts playing. In Trunk Mode and connected to one of the FXO ports on the SPA8800, the paging system never works -- when Asterisk tries to place any call to the SPA8800's FXO port, the SPA8800 replies with 503 Service Unavailable and nothing comes out the speakers. I've done some testing with a plain old analog phone connected to the Viking in Trunk Mode, and the paging system basically isn't outputting dial-tone -- when in Trunk Mode it just sits there waiting for some audio to come in the trunk port and then records & rebroadcasts that audio. My suspicion is that this lack of dial-tone is causing the SPA8800 to think the FXO line is dead. I've looked for a setting to tell the SPA8800 to ignore the lack of dial-tone and just try to automatically blast audio out the FXO port, but I cannot find it. Does that setting exist? Is there a SIP Header I can have Asterisk send to make the SPA8800 just send the call to the FXO port without a dial string and without waiting for dial tone?

Try 120 minute best quality.
Don't forget to compress the audio to AC3.
If that ends up too large, duplicate the preset you just used and dial down the bitrate and save it. Then apply the new version and try again.
Rinse and repeat as nec till it fits.
x

Configuration requried for 4 port ISDN S/T Interface card as backup link

Similar Messages

Maybe you are looking for