Configure 2 VLANs SG-200-26P using WRVS4400N

I would like to configure two VLANs on my SG-200-26p switch. Using port 25 for VLAN 1 and port 26 for VLAN 2 coming from my WRVS4400N. Then assign individual port (1-24) to one or the other VLAN.
My router has 2 VLANs private (1) Public (2). Private is conifured for ports 1, 3&4 and private wireless. Public configured port 2 and public wireless.
Each work fine with different IPs on each VLAN.
Can I configure the Switch as mentioned above using port 25 and 26? Is there instructions somewhere?

PEOPLEVISION,
It sounds like you are very close to making this work. You simply need to create VLAN 2 on the switch and assign ports to each VLAN.
Go to VLAN Managgement-> Create VLAN and Add.
VLAN ID: 2
VLAN Name: Guest
Go to Port VLAN Membership and click Join VLAN... at the bottom. Select port 26 from the dropdown. In the right box, select 1UP and use the left arrow to move it to the left box. Then select 2 from the left box and choose Untagged at the bottom. Use the right arrow to move 2UP to the right box. Now port 26 is a member of VLAN 2 untagged.
Do the same for any other port that you want to be a member of VLAN 2.
You can also create a Trunk port between the WRVS4400N and SG200 which will pass both VLAN 1 and 2 over the same connection. In that case on both the router and switch make the port a trunk and add VLAN 1 Tagged and VLAN 2 Untagged.
Please reply if you have any questions.
- Marty

Similar Messages

VLAN Assignment of SSID using Cisco AV Pair or Dot1x ?

Hi.
I am looking to setup wireless access to 2 of my internal VLANs. I am using Cisco 1130AG, PEAP and RADIUS for the authentication as one network is for employees only and one restricted to guests only.
I was wondering which was the most recommended solution.
1. To have 2 SSIDs, with one in each VLAN with the access restricted using the Cisco AV Pair attribute in RADIUS
or
2. Use one SSID and use Dot1x and the Tunnel attribute to assign the VLAN?
This option I feel is more complicated and I am still unsure how this works in reality as the SSID itself can only be part of one VLAN????
Do I have to configure a Dot11Radio and Fastethernet interface for each intended vlan in this case?
Could someone please explain and suggest their preferred option.
Thanks.

You should have two ssid's one for your internal and one for guest. You should use 802.1x for your internal and your guest should be open with a Login page of some sort. You can still use dynamic vlan assignments so that your internal users who try to access the guest page will be put on the internal vlan. Of course the guest will always be placed on the guest vlan. If you have a WLC, the login page and setup is easier, because in autonomous you will have to use something like ZoneCD for guest if you want a HotSpot type wifi.

Configuring Guest VLAN on AP541N and UC560

I have a AP541N connected to a UC560. We are currently configured for Wireless Voice and Data. We have added a Guest VLAN, but don't see where in CCA to secure the VLAN from accessing the other other two default VLANs. Any help would be appreciated.
Additional Info:
AP541N-K9-1.7(2)
UC560 15.0(1)XA2, RELEASE SOFTWARE (fc2)
CCA 3.0

https://supportforums.cisco.com/docs/DOC-14855
We are experincing the exact same problem in our lab.
There is no way with CCA that the VLANs can be secured. You have to use CLI, howerver once you choose to use CLI for configuration CCA may no longer be used.
Hope this helps.
Terry

Need help configuring multiple VLANs and SSIDs

Hi,
We bought a Cisco SGE2000P 24Port switch and 10 WAP4410N access points. Our intent is to provide a secure network to our LAN, and a guest network to the Internet.
We are thinking 3 VLANs would be best for this: VLAN 100 connected to the LAN, VLAN 1000 for the Internet Router and Filter, and VLAN 1100 for the Guest Wireless access.
We have the switch configured for all three of these, and 1 initial access point configured for the VLANS, too.
We have not yet moved the current Internet connection to VLAN 1000 because we aren't sure how to setup routing between VLANS.
Here are some specifics on how the traffic needs to route:
1. We have the DHCP server, which is the PDC, handling both scopes for the LAN and Guest VLAN.
2. The web filter in VLAN 1100 needs to authenticate with the DHCP server as there are different filter rules based on authenticated user. Any users coming from VLAN 1100 will have a default filter rule without requiring any authentication.
3. Certain traffic coming in from the Internet needs to be able to get to VLAN 100. The router has a built-in firewall that handles NAT and port forwarding, so as long as traffic can be forwarded to VLAN 100 we should be good.
4. Traffic on VLAN 1100 (guest Wireless network) should only be allowed to go to Internet (VLAN 1000).
Right now I have the VLANs configured and the ports assigned to the Access Points are set for TAGGED and on VLAN 100 and VLAN 1100.
The SGE2000P has the following IP addresses assigned to the VLANS:
10.7.3.252 - VLAN 100
10.7.40.254 - VLAN 1000
192.168.254.254 - VLAN 1100
Has anyone been able to setup a similar configuration? We have scoured the Internet for documentation but it seems to be very difficult to find!
Thank you!
Gary Smith

Based on your description of a 'Hybrid Port' this sounds like Cisco's 'Multi-VLAN Port' that was a feature of the 2900XL/3500XL series switches. This feature has however long since gone......
With a Cisco switch an access port supporting an Access VLAN & a Voice VLAN is effectively a Trunk with only one Tagged VLAN and the Native VLAN:
interface FastEthernet0/1
switchport mode access
switchport access vlan 10
switchport voice vlan 100
This results in the same configuration as:
interface FastEthernet0/1
switchport mode trunk
switchport trunk encapsulation dot1q
switchport trunk native vlan 10
switchport trunk allowed vlan 100
With the exception of CDP packets being sent advertising the Voice VLAN.
With regards to other IP Phone vendors and DHCP Vendor Options - the answer is it depends....
Nortel use Vendor Option 144 to inform the IP Phone of the Voice VLAN and Option 128 for the Server (PBX) to use. Ericsson uses Vendor Option 43 that can be configured to tell the IP Phone the VLAN and the Web server to read the config file from.
I don't think you will get this working automatically with your 3Com switches, you can however manually configure the VLAN on the Cisco IP Phones.
HTH
Andy

How to configure Oracle 10g Advanced Security to use SSL concurrently with

How to configure Oracle 10g Advanced Security to use SSL concurrently with database User names and passwords
In Oracle Advanced Security Documentation it is mentioned that i can use SSL concurrently with DB user names and passwords. But when i configure the client certificate on the client my DB connection is getting authenticated using the certificate, which out passing user id or password.
We want to connect to Oracle DB over SSL channel so that the data packets are not in clear text. Also we want the user to make a connection using user id and password.
Basically we want SSL with out authentication.
Need your expert advice

Read the documentation (I have given following links assuming you are running a 32 bit architecture)
Server installations:
http://www.oracle.com/pls/db102/to_toc?pathname=install.102%2Fb14316%2Ftoc.htm&remark=portal+%28Books%29
Client installations:
http://www.oracle.com/pls/db102/to_toc?pathname=install.102%2Fb14312%2Ftoc.htm&remark=portal+%28Books%29
You can find the required books (if not using 32 bit architecture) from
http://www.oracle.com/pls/db102/portal.portal_db?selected=3

Trying to configure a Win 2003 Server to use TLS server authentication . . .

I am trying to
configure a Win 2003 Server to use TLS server authentication following Method 2 in KB 895443 - see below:-
Method 2: By using the Certificate Request Wizard
The following steps describe how to obtain a certificate from a Windows Server 2003 Certification Authority. You can also request a certificate from a Windows 2000
Certification Authority. Additionally, you must have Read permissions and Enroll permissions on the certificate template file to successfully request a certificate. Use this method if one or more of the following conditions are true:
You want to request a certificate from an Enterprise Certification Authority.
You want to request a certificate that is based on a template where the subject name is generated by Windows.
You want to obtain a certificate that does not require administrator approval before the certificate is issued.
To obtain a certificate, follow these steps:
Click Start, click Run, type mmc, and then click OK.
On the File menu, click Add/Remove Snap-in.
Click Add, click Certificates, and then click Add.
Click Computer account, and then click Next.
If you want to add a certificate to the local computer, click Local computer. If you want to add a certificate to a remote computer, click Another
computer, and then type the name of that remote computer in the Another computer box.
Click Finish.
In the Add Standalone Snap-in dialog box, click Close, and then click OK in the Add/Remove
Snap-in dialog box.
Under Console Root, click Certificates (Local Computer).
Note If you configured the Certificates MMC snap-in to manage a remote computer, click Certificates (servername)instead of Certificates (Local Computer).
On the View menu, click Options.
In the View Options dialog box, click Certificate purpose, and then click OK.
In the right pane, right-click Server Authentication, point to All Tasks, and then click Request New Certificate.
In the Certificate Request Wizard that starts, click Next.
In the Certificate types list, click Server Authentication, click to select the Advanced check box,
and then click Next.
In the Cryptographic Service Providers list, click Microsoft RSA SChannel Cryptographic Provider.
I get as far as step 11 and I get the error message:-
The wizard cannot be started because of one or more of the following conditions:
- There are no trusted certification authorities (CAs) available.
- You do not have the permissions to request certificates from the available CAs.
- The available CAs issue certificates for which you do not have permissions.
This is covered in KB 927066 – see below:-
To resolve the problem, follow these steps:
Verify that the CERTSVC_DCOM_ACCESS group exists in the domain that hosts the certification authority. This group is in the CN=Users container.
To do this, follow these steps:
Click Start, click Run,
type Dsa.msc, and then click OK.
In the left pane, click the Users container.
Verify that the CERTSVC_DCOM_ACCESS group is in the right
pane. If the CERTSVC_DCOM_ACCESS group is not in the right pane, go to step 4.
Verify that the CERTSVC_DCOM_ACCESS group includes the following member groups:
Domain Users
Domain Computers
If these member groups do not exist in the CERTSVC_DCOM_ACCESS group, go to step 4.
Note If users or computers in other domains need to enroll against the certification authority, you must also add those users and computers to the CERTSVC_DCOM_ACCESS group. If the current problem occurs on a domain
controller, you must also add the Enterprise Domain Controllers group to the CERTSVC_DCOM_ACCESS group. By default, domain controllers are not members of the Domain Computers global group. Therefore, domain controllers
do not have sufficient DCOM permissions.
Verify that the CERTSVC_DCOM_ACCESS group has the appropriate DCOM Access permissions and DCOM Launch and Activation permissions on the computer that hosts the certification
authority.
Click Start, point to Program,
point to Administrative Tools, and then click Component Services.
Expand the Component Services node.
Expand the Computers node.
Right-click the My Computer node, and
then click Properties.
Click the COM Security tab.
Under Access Permission, click Edit
Limits.
Verify that the CERTSVC_DCOM_ACCESS group has Allow Local Access and Allow
Remote Access permissions, and then click Cancel.
Under Launch and Activation Permissions, click Edit
Limits.
Verify that the CERTSVC_DCOM_ACCESS group has Allow Local Activation and Allow
Remote Activationpermissions, and then click Cancel.
Click Cancel, and then close the Component
Services console.
Settings may be incorrect if any one of the following conditions is true:
The CERTSVC_DCOM_ACCESS group does not exist.
The default membership of the CERTSVC_DCOM_ACCESS group is incorrect.
The CERTSVC_DCOM_ACCESS group does not have the correct permissions.
If any one setting is incorrect, run the following commands at a command prompt. Press ENTER after each command.
certutil -setreg SetupStatus -SETUP_DCOM_SECURITY_UPDATED_FLAG
net stop certsvc
net start certsvc
Repeat steps 1 through 3 to verify that all the settings are correct.
Note If the changes affect the group membership of the certification authority server, you must restart the server for the changes to take effect.
The only part of the above instructions which I have not been able to complete is:-
“you must also add the Enterprise Domain Controllers group to the CERTSVC_DCOM_ACCESS group”.
When I click on the CERTSVC_DCOM_ACCESS user then click the Members tab & go to add Enterprise Domain Controllers the option is not there.

Hi Nick,
Have you successfully set up an enterprise CA?
If yes, is the enterprise CA’s certificate located under the Trusted Root Certification Authorities store?
Best Regards,
Amy

How do I configure a counter to generate pulses using DAQmx?

How do I configure a counter to generate pulses using DAQmx?
Is says in the DAQmx C reference help
"CtrnInternalOutput—The signal at this internal terminal is where the pulsed or toggled output of the counter appears. The output of a counter pulses or toggles when the counter reaches terminal count. When counting down, the counter reaches terminal count when the count reaches zero. When counting up, the counter reaches terminal count when the counter rolls over. To configure the counter to toggle or generate pulses, use the Export Signal function/VI with Counter Output Event as the signal name."
I've tried this but can't get it to work, I may have the parameters wrong or something. The DAQmxExportSignal() function is very unintuitive to me. Here is my counter config code...
int ret = 0;
ret = DAQmxCreateTask("",&task_);
errorMsg(ret);
if (ret != 0)
throw ret;
// Configure the counter
ret = DAQmxCreateCOPulseChanTicks( task_, "Dev1/ctr0", "", "/Dev1/PFI8", DAQmx_Val_Low, 0, divider, divider );
errorMsg(ret);
ret = DAQmxCfgImplicitTiming( task_, DAQmx_Val_ContSamps, 1000 );
errorMsg(ret);
// Change to pulse mode
ret = DAQmxExportSignal( task_, DAQmx_Val_CounterOutputEvent, "/Dev1/Ctr0InternalOutput" );
errorMsg(ret);
// Start the counter
ret = DAQmxStartTask(task_);
errorMsg(ret);
The above code works fine, in toggle mode, if I just comment out the DAQmxExportSignal() part.
HELP!!!
Stefan

The problem is due to the DAQmxExportSignal call. By default, when you create a counter output pulse train task, the driver will automatically set the output of the counter to toggle when the count for each high ticks and low ticks expire. The driver also automatically routes the signal present at Ctr0InternalOutput terminal (the output of the counter internal to the device) to the Ctr0Out terminal (the I/O pin available externally). Using the line
ret = DAQmxExportSignal( task_, DAQmx_Val_CounterOutputEvent, "/Dev1/Ctr0InternalOutput" );
will tell the driver to tristate the Ctr0Out terminal and not output the signal to the external I/O pin. Using the DAQmxExportSignal function is generally only useful if you want to route the signal to some other terminal internal to the board without having the output show up on the external connector, route the signal to some other external pin other than the default pin, or if you want to have the output show up at multiple locations.
If you want to change the output behavior from toggle to pulse, you need to use the DAQmxSetExportedCtrOutEventOutputBehavior function. However, this is generally only useful if all you care about are edges (not the duty cycle of the pulse train), and you want to generate higher frequency signals. For example, with a 20 MHz timebase as the source of your counter, you can only generate a 5 MHz pulse train by default. This is because the minimum value for the low and high ticks parameter is 2 (20 MHz / 4 = 5 MHz). By changing the output behavior form toggle to pulse, you can generate a pulse train at 10 MHz since the output is now pulsing instead of toggling. However, the width of each pulse is not programmable so you will no longer have a 50% duty cycle signal. I don't remember exactly what the width of each pulse is, but I believe it's in the neighborhood of 50 - 100 nanoseconds in width. I hope this information helps.

How to configure current SQL high availability cluster using mirroring with dedicated replication NICS?

We have a current HA cluster at center1 which is mirrored to another HA cluster in center2. We have several instances already installed and working which are using one NIC for data and replication. We want to prevent mirror failovers by
configuring a NIC on a replication network which has no DNS server. What are the steps to configure the current SQL instances to use this dedicated NIC for mirror replication?

Hi dskim111,
You can refer the following step by step article to create the dedicated mirroring NIC,
Step by Step Guide to Setup a Dedicated SQL Database Mirroring(DBM on dedicated Nic card)
http://blogs.msdn.com/b/sqlserverfaq/archive/2010/03/31/step-by-step-guide-to-setup-a-dedicated-sql-database-mirroring-dbm-on-dedicated-nic-card.aspx?Redirected=true
I’m glad to be of help to you!
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

How to configure SNMP on all managed client using SCCM 2012 SP1

hi ,
do you know How to configure SNMP on all managed client using SCCM 2012 SP1?

As a side note, I made an interesting discovery last week: the SNMP Service is deprecated in Windows Server 2012. Why would you want to use SNMP on an actual Windows OS though? There are far better ways available to monitor Windows. I'm sure that lines
up with why they deprecated it.
Jason | http://blog.configmgrftw.com

ACS with Dynamic VLAN which protocol to use ??

Hello,
Which Protocol do I need to use, for providing dynamic VLAN to my desktop machines?
As in ACS 4.0 if I use local database of ACS then users successfully get the dynamic VLAN & as soon I use AD database while integration it with ACS ,the authentication fails!!
Please help.

Hi,
Thanks for the reply. I am using EAP-MD5.
However, the problem is if I am using ACS solution Engine local database, users are getting dynamic VLAN after authentication.
But when I use AD as user database, the authentication fails. Even strange thing is that if I use AD database to log in to any Cisco Router then the authentication is working fine.
Even I am struggling with TAC also from last week in two different cases! However, they are unable to help! I found TAC has limited resource for ACS.
So please suggest what to do as on Cisco site, I found lots of stuff for Wireless but I have only the desktops (no wireless).
So will the mention below URL be of any help?
http://www.cisco.com/en/US/products/sw/secursw/ps2086/products_configuration_example09186a00805e7a18.shtml
Thanks in advance
Vijay

I want to configure the 7330 motion controller without using MAX

I am new to labview and I have a project where I have to configure the 7330 motion controller without using MAX. What do I need to do to get started doing so?
Thanks for the help!
nw2labview

Hi,
There are several VI's that are included with the motion driver for configuring your controller. They are located on the function pallete under Vision and Motion>>Ni-Motion>>Axis Configuration. Using these VI's you will be able to configure your axis. But why don't you want to use MAX? If you are new to LabVIEW I would suggest configuring and testing your motor in MAX first before you start programing. Once you have it working there you may want to look at several of the examples such as Simple One-Axis Move.vi. I hope this helps.
GG

How does one delete VPN configurations in the settings list not used any more?

How does one delete VPN configurations in the settings list not used any more?

Sorted found profiles and delete from there

SQL Server Management Studio - Configuring the environment for first time use

Hi
I have recently switched my local 'My Documents' folder location to a network drive that I 'make available off line' to allow on-line/off-line work and synchronisation when I am working in and out of the office.
When I load my SQL Server Management Studio 2005 I frequently get 'Microsoft SQL Server Management Studio is configuring the environment for first time use'.
Management Studio them loads and I can continue without problem.
I am guessing it is trying to make reference to some settings file. Any ideas? I wonder if I can change/move these settings elsewhere to a local drive?
Thanks

Hi,
There is bug report of this issue:
http://connect.microsoft.com/SQLServer/feedback/details/126364/configuring-enviroment-for-the-first-time-every-time-in-ms-sql-server-management-express
"SQL Server Management Studio Express saves the settings for the user in ...\Documents and Settings\<User Profile>\Local Settings\Application Data\Microsoft\Microsoft SQL Server\90\Tools\ShellSEM
and in ...\Documents and Settings\<user profile>\Application Data\Microsoft\Microsoft SQL Server\90\Tools\ShellSEM
if any of these files are not available or unusable, SSMSE will generate new ones."
Hope this helps.
BR,
JoukoK

Configure ag6000 Scope IVI driver to use math channels

Hi all,
just before capitulating using the generic Teststand-IVI Scope driver capabilities, one try get help here:
We want to use a ag6000 compatible scope with teststand. The first guess is to use the ag6000 IVI compatible driver, and directly use IVI-scope steps within teststand.
Connection and step usage works so far, but:
1. How do I configure the math channel to be used from within teststand? The ag6000 driver itself provides the necc. functions when used with CVI, but the generic Teststand IVI Steps don't have this functionality (or I'm to blind to find it?)
The alternative approach I'll start, is to encapsulate the ag6000 driver in a cvi DLL and use this within teststand.
2. Unsupported feature seems to be having an AUTO trigger or something like a continous measurement. (We also need to measure DC without crossing any trigger level)
Any Ideas?
David

All of the functions in the IVI are defined by the IVI Foundation - not NI or TestStand. They pick the functions that are most common to all scopes. If there is a specific instrumention function that you need to use, you have to use the specific driver for the scope. Doing that, of course, removes a lot of the reasons for using IVI in the first place.

How do I configure Soundtrack Pro2 to play audio using Digidesign 002 Rack?

How do I configure Soundtrack Pro2 to play audio using Digidesign 002 Rack? I have no problem using Logic 8 with the 002 Rack?
Can somebody explain the necessary process to make this work. Thanks

Add is probably not the best choice of terminology.
Going from memory (since I'm at home), you need to launch digiCoreAudio, then select your output in the System prefs as your digi hardware. After that you would see the digi hardware as an output in STP.

Configure 2 VLANs SG-200-26P using WRVS4400N

Similar Messages

Maybe you are looking for