Configure FAX in cme

Hi all
I have cme 2921 router and 4-port FXO
possible the configure FAX in fxo port ?
I need purchase FXS card or ATM
my cme version 9.0
Thanks

You need an FXS card if you want to connect a fax machine to the router. FXO ports ae used to connect analog circuits from the provider* and some paging equipment.
*The very rare analog DNIS circuit actually requires an FXS card too. Again, very uncommon though.
Please remember to rate helpful responses and identify helpful or correct answers.

Similar Messages

SMTP :Configuring Fax

Hi All,
I am trying to configure Fax in our ERP system.SMTP mail configurationhas been done and its working fine.
Now while configuring Fax i tried to use the same SMTP server ,but not sure if Fax i s supported there.
Tried ot send the Fax using this but system throwed error that
===================================
Processing was terminated in the SAP system. The reason is given in the details below:
Received e-Mail address FAX=91useid@FAX=RECIPIE
=====================================
Can you please give me steps required to configure Fax and what are the pre-requiistes for this .
Regards
Ajay
Edited by: Ajay Sandal on Jan 27, 2010 2:42 PM

Hi Juan
Thanks for the information so far.
Actually IT team doesn't have any FAX server and now i need to do a kind of demo of the requirement.
Can we use FAX provider ,like i found some for MS Outlook to deliver FAX .If i provide the domain of the FAX service provider say RAPIDFAX etc will that work.
Suppose we procure a FAX server ,will it be able to send FAXes to US or India or Australia ,or we need to do some extra things for that.
Excuse me for lot of questions
Regards
Ajay

Configuring FAX on ATA 186 with CME 3.4

Hi,
I have an ATA 186 connected to my network, I have configured CME for auto assign extensions & I got an extension as well, when I connect analog phone it works fine but when I connect FAX Machine I cannot send & recieve fax. Do I need to change any configurations in ATA???? Please check the screen shot attached

Try this link for more information on configuraing FAX on ATA
http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_configuration_example09186a00800d698e.shtml

ATA 186 for FAX With CME

Hi,
I have ATA 186 connected to my network when i connect a phone it works but when I connected fax machine i cannot recieve or send faxes...do I need to do any configurations in ATA...please check the attachment..

you'll need dial peer(s), on your CME router, that enable FAX passthrough as well as a few other pieces.
please see the following link for Config/Troubleshooting ATA-186 with FAX:
http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_configuration_example09186a00800d698e.shtml#task2

Configure 3905 on CME 8.5

Hello everyone,
I have to configure a Cisco SIP phone 3905 in CME ver 8.6. I haven't found a way to do this.
I tought about doing it with Fast Track (voice register global-type), but it is supported on CME 10 and above.
I was thinking about registering it like a 3rd party sip phone, but I don't know where to put the username and password on the phone. The Web Admin page of the 3905 only shows info.
Any idea how can I work this out?

Hi Bruno,
3905 is supported with CME 9.0 onwards, please upgrade to a supported CME version.
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/requirements/guide/cme85spc-htm.html
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/requirements/guide/cme90spc.html
HTH
Manish

Output of Purchase order Configured FAX as medium..

Hi All,
One of Purchase order is configured with communication medium as FAX and output type as NEU.How to see the output?
Thanks

hi
Output of Purchase Order
1. Condition Table
SPRO > Material Management> Purchasing -> Message -> Output Control->Condition Tables->Define Condition Table for Purchase Order
Select:
Purchasing Doc. Type, Purch. Organization, Vendor
2. Access Sequences
SPRO -> Material Management-> Purchasing -> Message -> Output Control->Access Sequences->Define Condition Table for Purchase Order
3. Message Type
SPRO -> Material Management-> Purchasing -> Message -> Output Control->Message Types->Define Message Type for Purchase Order
*4. Message Determination Schemas*
4.1. Message Determination Schemas
SPRO -> Material Management-> Purchasing -> Message -> Output Control->Message Schema->Define Message Schema for Purchase Order-> Maintain Message Determination Schema
4.2. Assign Schema to Purchase Order
SPRO -> Material Management-> Purchasing -> Message -> Output Control->Message Schema->Define Message Schema for Purchase Order-> Assign Schema to Purchase Order
5. Partner Roles per Message Type
SPRO -> Material Management-> Purchasing -> Message -> Output Control-> Partner Roles per Message Type ->Define Partner Role for Purchase Order
6. Condition Record
Navigation Path: SAP Menu-> Logistics -> Material Management -> Purchasing-> Master data-
here all above steps u can do from transacton NACE
now when u create po in the messages select out put as FAX and the take out put
http://www.scribd.com/doc/7839934/Faxing-a-Purchase-Order
regards
KI
Edited by: SAP Learner on Apr 17, 2009 12:15 PM

Configuring FAX machine to Solaris 8

We need to configure a Solaris 8 machine to a FAX machine. Do anybody know how to do that?
Please advice me.
Thanks in advance
Regards
Suresh

HI,
i don't know sunscreen, but i can tell you that high-ports are ports above 1023.
J

Configuration Issue with CME

Hello Folks,
When we enable the night service, the incoming call hears 20 rings and then the call gets dead. It looks like it doen't transfer to Automated Attendant(extension 9998)configured in ephone-dn 115. Here's the config that I have for the ephone-dn.
ephone-dn 1 dual-line
number 2300
pickup-group ReceptionistNotAvailable
label Receptionist-1
name Receptionist-1
no huntstop
night-service bell
ephone-dn 111 dual-line
number 2300
label Receptionist-2
preference 1
no huntstop
ephone-dn 112 dual-line
number 2300
label Receptionist-3
preference 2
no huntstop
ephone-dn 113 dual-line
number 2300
label Receptionist-4
preference 3
no huntstop
ephone-dn 114 dual-line
number 2300
label Receptionist-5
preference 4
no huntstop
ephone-dn 115 dual-line
number 2300
label Receptionist-6
preference 5
call-forward noan 9998 timeout 10
and the following is the config for the ephone which are participating in Night Service:
ephone 5
username "User5"
mac-address 0015.FA25.DB95
type 7940
button 1:5 2:14
night-service bell
ephone 6
username "User6"
mac-address 0015.FA25.DA90
type 7940
button 1:6 2:15
night-service bell
Thanks,

You can use call-forward all that is set manually by receptionist at the end of the day and taken off in the morning.
You can also use call-forward night-service.
For more information please go to Call-Coverage Features section http://www.cisco.com/en/US/products/sw/voicesw/ps4625/products_configuration_guide_book09186a00806a80dd.html

Connecting/configuring FAX over wifi

I have a Cannon MX882 set up in my upstairs office and I would like to have it connected to my Xfinity voice via my wireless network. I can't find directions? Can anyone help?

You can not, the fax needs a direct telephone line connected to the gateway or eMTA's telephone port. The fax portion does not use wi-fi or your home network to fax, that is only for printing / scanning.
Most users backfeed their Comcast telephone port to the inside wiring in the home and use the existing phone jacks in the home to connect telephones, fax and other devices needing a phone line.

Configuring VG248 for fax

Hi
I have a few questions about configuring fax connected to VG248 (yes, i know its EOL but the end customer hasnt descided to replace them yet).
The setup is like this:
Fax -> VG248 -> CUBE -> SIP-trunk
or i can choose to include the CUCM which would make it look like:
Fax -> VG248 -> CUCM -> CUBE -> SIP-trunk
Should i use T.38, or NSE or?
I have been looking at this:
https://supportforums.cisco.com/docs/DOC-25210
Can i configure all dial-peers on CUCM with both T.38 and NSE so that when the VG248 are replaced i dont have to do any reconfiguring in CUBE?
CUBE
fax protocol t38 nse ls-redundancy 0 hs-redundancy 0 fallback pass-through <g711ulaw or g711alaw>
fax-relay ecm disable
VG248
1) Configure --> Telephony --> Port specific parameters --> Choose the port to which the Fax machine is connected
   a) Set "Fax Relay" to "T.38 peer to peer"
   b) Set "Fax relay ECM" to "disabled"
   c) Set "Fax relay NSF" to "override with 000000"
2) Configure --> Telephony --> Advanced Settings
    Set "Passthrough signaling" to IOS Mode
And here is a problem:
I dont have the choice to set the VG248 port to " fax relay - T.38 peer to peer"
CUCM, CUBE and VG248 are up and running in production so i have to be careful.
Sorry for not being more precise.
Versions:
VG248: Software version : 1.3(1)
CUBE: 15.1(4)M4
CUCM: 8.0.3.22900-5
CUCM: 8.6.2.22900-9
(there are two different CUCM clusters but both wil have the same setup regarding the fax'es)
/Tony

Craig,
You can achieve this by using COR and multiple dial-peers outbound. Essentially you would apply an inbound dial-peer matching the ANI of your fax on your gateway. This inbound dial-peer would have an incoming cor-list. Then you would add another cor-list to your existing dial-peers, making sure they don't include the fax inbound cor. Then you would duplicate an outbound pattern with a cor-list the faxes can use. Here is an example below, assuming the Fax DN is 1000 with an e164 of 0886441000.
dial-peer cor custom
name faxnumber1000
name longdistance-nofax
dial-peer cor list faxnumber1000
member faxnumber1000
dial-peer cor list longdistance-nofax
member longdistance-nofax
dial-peer voice 1000 voip
description Inbound Fax dial-peer Fax DN 1000
incoming-called number 1000
corlist incoming faxnumber1000
dial-peer voice 11 pots
description Original Outbound LD dialpeer
destination-pattern 9T
clid network-number 0886448580
corlist outgoing longdistance-nofax
port x/x
dial-peer voice 12 pots
description Fax only LD dialpeer
destination-pattern 9T
clid network-number 0886441000
corlist outgoing faxnumber1000
preference 1
port x/x
COR will restrict the fax from ever using the dial-peer with the incorrect CLID. The preference on the fax dial-peer will prevent in most scenarios anyone else using it but you could also apply COR to the remainder of the router to 100% guarantee fax only usage of that dial-peer.
Here is a document explaining COR(note this will discuss how to set it up and not for using it as a workaround to your issue).
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_configuration_example09186a008019d649.shtml
Please rate any helpful posts
Thanks
Fred

Data, voice, video & fax over the satellite link

Hi,
We have a requirement for Cisco voice to be implemented at our satellite teleport. This is basically to connect our teleport location HO to Barge (sea platform - rig) via the satellite. At the rig we would require data, voice, video & fax services. The satellite WAN BW is 256kbps. The Barge users will use four telephones, one fax & will do videoconferencing. They will communicate with teleport HO & use the PSTN for internationatal dialling using the HO voice gateway.There is no Cisco call manager in place. There is PBX (Brand-NEC, Model- NECX 2400) system at the HO.
Appreciate if somebody can recommend as to what would be the best way to provide voice, fax & video connectivity to the users in the barge.Thanks.
Rgds./
Sack

Buy Unified Communications Manager, SageCom XMediusFAX, and a Cisco ISR G2 router for the head office to provide PSTN calling and faxing support. Buy a second ISR G2 with Unified Communications license, the appropriate CME license count, and a ISM running CUE for voicemail. Configure UCM and CME to communicate using a SIP trunk and configure QoS on the satellite to prioritize the voice and signaling traffic. You will not get video calling across a link that small.

4FXS-DID configuration problem using BRI to receive/send calls from/to PSTN

Hi to all.
Follow is the partial configuration of my CME.
It has a 4FXS card to use analog phones and faxes, and 4 ISDN Basic Rate interfaces.
On each port of the 4FXS DID card happens the following:
If I enable direct-inward-dial
    I can receive calls from PSTN.
     Off hooking the analog phone I cannot hear any free line tone. I cannot make any call from that phone.
If I disable direct-inward-dial
    I cannot receive directly calls form PSTN.
          Callers on PSTN after typing my number, they hear a free tone. Then just typing the extension desired the phone ring.
     Off hooking the analog phone I hear a free line tone. I can make normal calls to everyone.
I have half the configuration working.
Where am I wrong?
I really appreciate your help.
Thanks to all.
Giorgio.
CME#sh ver
Cisco IOS Software, 2800 Software (C2800NM-IPVOICEK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2)
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
CME uptime is 2 days, 15 hours, 49 minutes
System returned to ROM by power-on
System restarted at 18:54:45 CDT Fri Aug 2 2013
System image file is "flash:/c2800nm-ipvoicek9-mz.124-24.T3.bin"
Cisco 2811 (revision 53.50) with 249856K/12288K bytes of memory.
Processor board ID FTX1120A08L
2 FastEthernet interfaces
4 ISDN Basic Rate interfaces
16 terminal lines
4 Voice FXS interfaces
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
1948656K bytes of USB Flash usbflash0 (Read/Write)
497448K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
CME#sh telephony-service
CONFIG (Version=7.1)
=====================
Version 7.1
Cisco Unified Communications Manager Express
isdn switch-type basic-net3
voice translation-rule 1
rule 1 /^2929091$..$/ /\1/
rule 2 /^2929091$.$/ /\1/
rule 3 /^02929091$..$/ /\1/
rule 4 /^02929091$.$/ /\1/
voice translation-rule 2
rule 2 /$.*$/ /02929091\1/
voice translation-rule 10
rule 1 /$^......$$/ /0\1/ type national national plan isdn isdn
rule 8 /$^......$$/ /00\1/ type international international plan isdn isdn
voice translation-profile PSTN-IN
translate calling 10
translate called 1
voice translation-profile PSTN-OUT
translate calling 2
interface BRI0/0/0
description Isdn channels 1 & 2
no ip address
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/0/1
description Isdn channels 3 & 4
no ip address
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/1/0
description Isdn channels 5 & 6
no ip address
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/1/1
description not used
no ip address
shutdown
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
voice-port 0/0/0
translation-profile incoming PSTN-IN
translation-profile outgoing PSTN-OUT
compand-type a-law
description Connessione con CO Telecom channels 1 & 2
voice-port 0/0/1
translation-profile incoming PSTN-IN
translation-profile outgoing PSTN-OUT
compand-type a-law
description Connessione con CO Telecom channels 3 & 4
voice-port 0/1/0
translation-profile incoming PSTN-IN
translation-profile outgoing PSTN-OUT
compand-type a-law
description Connessione con CO Telecom channels 5 & 6
voice-port 0/1/1
description Disponibile
voice-port 0/2/0
input gain 14
connection plar 83
description Interphone 40
station-id name Citofono
station-id number 40
caller-id enable
voice-port 0/2/1
cptone IT
description Ced 35
station-id name CED
station-id number 35
caller-id enable
voice-port 0/2/2
cptone IT
description FAX_1 50
station-id name FAX_1
station-id number 50
caller-id enable
voice-port 0/2/3
cptone IT
description FAX_2 60
station-id name FAX_1
station-id number 60
caller-id enable
dial-peer voice 1001 pots
description **Sends call to PSTN line 1-2**
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/0
dial-peer voice 2001 pots
description **Receives calls coming from PSTN line 1-2**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/0
dial-peer voice 1003 pots
description **Sends call to PSTN line 3-4**
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
dial-peer voice 2003 pots
description **Receives calls coming from PSTN line 3-4**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/1
dial-peer voice 1005 pots
description **Sends call to PSTN line 5-6**
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 2005 pots
description **Receives calls coming from PSTN line 5-6**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/1/0
dial-peer voice 2035 pots
description **Receives calls coming from PSTN to Extension 35**
answer-address 35
destination-pattern 35$
incoming called-number 35
port 0/2/1
dial-peer voice 2040 pots
description **Receives calls coming from PSTN to Extension 40**
destination-pattern 40
incoming called-number 40
no digit-strip
direct-inward-dial
port 0/2/0
dial-peer voice 2050 pots
description **Receives calls coming from PSTN to Fax 50**
destination-pattern 50
incoming called-number 50
no digit-strip
direct-inward-dial
port 0/2/2
dial-peer voice 2060 pots
description **Receives calls coming from PSTN to Fax 60**
destination-pattern 60
incoming called-number 60
no digit-strip
direct-inward-dial
port 0/2/3
CME#

Hi Paolo.
Sorry for the delay. I was on holiday.
I would like to keep separate incoming calls from outgoing calls.
So I decided to keep two dial peers for every BRI interface.
I followed your suggestion on eliminate commands:
"incoming called-number" on FXSs,
various "progress_ind" on BRIs
Also I eliminated "direct-inward-dial" on FXSs,
Today I reconfigured and right tested the dial peers as following:
!   Bri Interfaces
dial-peer voice 1001 pots
description **Sends call to PSTN line 1-2**
destination-pattern 0T
port 0/0/0
dial-peer voice 2001 pots
description **Receives calls coming from PSTN line 1-2**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/0
dial-peer voice 1003 pots
description **Sends call to PSTN line 3-4**
destination-pattern 0T
port 0/0/1
dial-peer voice 2003 pots
description **Receives calls coming from PSTN line 3-4**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/1
dial-peer voice 1005 pots
description **Sends call to PSTN line 5-6**
destination-pattern 0T
port 0/1/0
dial-peer voice 2005 pots
description **Receives calls coming from PSTN line 5-6**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/1/0
!   FXS interfaces
dial-peer voice 2035 pots
description **Receives calls coming from PSTN to Extension 35**
destination-pattern 35
no digit-strip
port 0/2/1
dial-peer voice 2040 pots
description **Receives calls coming from PSTN to Extension 40**
destination-pattern 40
no digit-strip
port 0/2/0
dial-peer voice 2050 pots
description **Receives calls coming from PSTN to Fax 50**
destination-pattern 50
no digit-strip
port 0/2/2
dial-peer voice 2060 pots
description **Receives calls coming from PSTN to Fax 60**
destination-pattern 60
no digit-strip
port 0/2/3
Thanks a lot Paolo. :-)
Giorgio.

Problem with Fax and ATA

Hi,
i do not have problem to send Fax to the PSTN, but when I try to receive a fax on the fax machine in port1 of the ATA, the machine never give fax signal.

Hi Leonardo,
Have a look at the following;
Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide (SCCP) (2.15.ms, Rev B0)
Configuring and Debugging Fax Services
http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_administration_guide_chapter09186a00800c4d1e.html#1016012
Configuring and Troubleshooting the Cisco ATA 186 with Fax
http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_configuration_example09186a00800d698e.shtml
Configure Fax Detection Method on the Cisco ATA 186
Use a web browser and go to http:///dev (for example, http://172.16.104.117/dev) in order to configure the Cisco ATA 186 using the web interface.
You must configure these parameters in order to configure the Cisco ATA 186.
Audio Mode
bit 2 (18)=0 Enable detection of FAX CED (answer) tone and switch to FAX mode for the rest of the call if the tone is detected.
Hope this helps!
Rob

Fax Detect help, PLEASE! :)

I'm looking to configure fax detect on the UC 520.
I can get listen-first to work for faxes only. After 9 seconds, or when I press any key...the call is disconnected.
If I confgure it for connect-first, the line just rings... never answers.
Config is attached.
PLEASE let me know what's missing ... I had this working a while back, and I don't remember what I needed to do.
I've also tried
app_fax_detect.2.1.2.2.tcl and
app_fax_detect.2.1.2.3.tcl
Same issue.
THANK YOU !!
Greg

Hey Gregory,
I was looking at your configuration and found that app is applied on FXO port. Can you please send me following from the UC520
show ver
show run
show flash
Also I would like you to enable following debugs and make a test call
debug voip ccap inout
debug voip vtsp all
debug vpm signal
debug voip application all
debug fax mta all
Please make sure that you are collecting the debugs on buffer and not on console.
Thanks,
Malick

Sending various documents through FAX in PO

Hi All
I had a requirement to FAX various kinds of documents like PDF WORD etc through FAX in Purchase Order.
It has to be accessed from Document Management System.
Any pointers in this shall be welcomed.
Thanks in advance
Anuj

Hi Saurabh,
You got standard way to do it . First your message has to be set to be send by Fax ( check in transaction NACE for this or check with your functionnal consultant ) .
After you have to make some technical customizing in transaction SCOT in order to configure Fax connexion from SAP and then set the file fomrat you want for fax.
Remember that if you want to send Fax directly from SAP, SAP need to be connected to a Fax Card or a Fax Server .
Hope this will help you.

Configure FAX in cme

Similar Messages

Maybe you are looking for