Configure "reset" for all default signatures

Hi all,
When I update signature (all default signature by Cisco), I want to configure "action: reset" for all default signatures (all default signatures that are turned on) . If you know how to do that, please answer me.
Thank you very much.
Duy Khang

Do you mean after each sig update? You can go into the sig configuration and do a "select by" release. you will get a drop-down box of releases, select the appropriate release. You can then sort by enabled. select multiple sigs at a time by using the shift key. now click the actions button to change multiple sigs at once.

Similar Messages

Is possible to config an subscrat rule for all the signatures enables in IPS?

Hi.
is possible to config an subscrat rule for all the signatures enables in IPS?
Thnks
Sent from Cisco Technical Support iPad App

Yes, In the event action filter configuration configure the signature range , victim IP address and the action to subtract.

After turning off and turning on my phone, push notifications resets for all my apps

After updating to ios 7.0.3, if I turn my phone off then back on, the push notifications prompt resets for all my apps. I have to go back in to apps and allow the apps to send me push notifications. Is there a solution for this or is it a bug?

http://www.verizonwireless.com/support/knowledge-base-26502/
Above if battery pull/soft reset doesn't help. If it's boot looped may need new equipment

Single XML configuration file for all the SSIS packages(including parent and child packages)

Hi
I have some 16 ssis packages. source Db and destination Db for these packages are common. I am calling these child packages in a master package.
I want to use only one XML config file for this master.
How do i use same for all child packages?
and can i do it with parent package variable?

I created a master package with a variable master, and in value i have entered the configuration file path.
Hi vjp dinu,
You should create variables in the parent package to pass values to variables in each child package rather than pass the file path of the XML Configurations file of the parent package.
As Visakh mentioned, you can achieve your goal by creating corresponding variables in the parent package for each child package, and enable Package Configurations for the parent package so that you can control the values through the XML Configurations file
for the variables of the parent package.
Supposing there is a variable FilePath in child package 1, a variable ServerName in child package 2, then, we need to create two variables pFilePath, pServerName in the parent package. After configuring the Parent package variable in each child package (e.g.
mapping pFilePath to FilePath, pServerName to ServerName), you can enable XML Configurations for the parent package, and expose the value property for both pFilePath and pServerName variables. In this way, you can modify the XML Configurations file of the
parent package and the specified values will passed to the child packages.
Reference:
http://microsoft-ssis.blogspot.com/2011/06/passing-variables-from-parent-package.html
Regards,
Mike Yin
TechNet Community Support

How do you configure Firefox for all users on a machine?

I want to
1. Take my existing set-up of Firefox
a. with all bookmarks
b. with all my chosen options
c. with my default start-up home page
d. bypass all the initial Firefox startup screen and "make this your default screen"
2. Have it be the base set-up for all users that log into a machine on our domain.
Is there a config file? Where do I place this config file so when all open their firefox it takes the above settings. I am creating a base image using VMware and will want this set-up so when a user log in with their logon credentials and open Firefox, it already has the above mentioned settings in place.

See CCK Wizard: https://addons.mozilla.org/firefox/addon/cck/
You can use a mozilla.cfg file in the Firefox program folder to lock prefs or specify new (default) values.
Place a file local-settings.js in the defaults\pref folder where you also find the file channel-prefs.js to specify using mozilla.cfg.
pref("general.config.filename", "mozilla.cfg");
pref("general.config.obscure_value", 0); // use this to disable the byte-shift
See:
*http://kb.mozillazine.org/Locking_preferences
These functions can be used in the mozilla.cfg file:
defaultPref(); // set new default value
pref(); // set pref, but allow changes in current session
lockPref(); // lock pref, disallow changes

1 configuration file for all control files

I happen to use sqlldr many times in my automation work. Most of the times few things in all my control files are same like
LOAD DATA
FIELDS TERMINATED BY ','
TRAILING NULLCOLS
However if for some reason, something like delimiter changes, then I have to change the second line in all my control files and this makes maintenance tough.
Was just wondering if its possible to store the common configuration settings in 1 config file and making sqlldr ctl files picking those common settings from 1 single file?
Regards,
Parag
Edited by: Parag Kalra on Jul 25, 2010 12:15 AM
Edited by: Parag Kalra on Jul 25, 2010 12:22 AM

Of course you don't mention a version. Type four digits and three dots: too much work.
Anyway: if you submit it as a feature request on Metaclunk, it might be arranged in release 13<whatever>, two years from now.
Sybrand Bakker
Senior Oracle DBA

Configuring EarlyWatchAlert for all the systems in the landscape

Gurus ,
In SDCCN can i configure EARLYWATCHALERT session with targethost as SDCC_OSS
now this has been only for production system . can this be done to all the systems in the landscape ?

Hi Susin,
As per me i could say the EWAlert only be configured for your production system rather
than the other systems(Dev/QA) existing in your ladscape.
If you are thinking to schedule this Alert for other products(BI/EP/XI) or for other SIDs,
then yes...please go ahead.
Why i am saying we can only schedule the EWAlert for production system, coz the
the EarlyWatch report uses the SDCC_OSS RFC, which is a copy of the SAPOSS connection. And the target destination refers to SAP's system where one copy of your
weekly shceduled EWAlert report goes to SAP end as well.
Please inform me incase any other queries...
Thank you,
Tilak

ITunes connection reset for all purchased content - won't download!

Hello,
I see many archived messages about this issue, however, it is a new problem for me. I have until now been able to download entire Seasons of shows without an issue, without interruption. Now, a single half-hour episode in standard definition fails.
Suddenly, any purchased content in iTunes - movies, TV shows, etc. - will not download into my Library, and I get a "network connection was reset" error. I am running iTunes 11.1.5 on Mavericks.
Recently I purchased & installed MacKeeper. I know it is a long shot, since this appears to be a network issue, but it is the only "change" introduced in recent weeks.
Hoping you can assist.
Thank you.
Anne Mowat

Well, I am very doubtful the issue was ever ISP related - I am not on Comcast nor even on cable (fioptics phone). And several other threads show many different ISP's across the globe were involved! Hence Apple Support seems to have indeed been trying to offload the problem... especially in light of what happened to me today!
I just upgraded to iTunes 11.2 and OS X 10.9.3 with the same positive results as harrharr's post, with either or both updates fixing the problem!
I downloaded 3 large movie files (make that 5 as 2 more just finished as I edited this!), each about 1GB in size with "Allow simultaneous downloads" on. All files finished on their own!! I haven't even come close to these results this week with the last movie I downloaded Wed taking over 15 restarts to finish! Now, I could be off to a lucky Fri, AND it could be either the iTunes or OS X update that fixed it (installed both at the same time so can't determine which one did it). Either way, it appears to be fixed and as I suspected the problem was on the Apple side, not anything I did with my router or any change from my ISP. Fingers crossed!
That said, if it is fixed, shame on you iTunes and Apple Support! Why do you continue to either (1) be so out of touch with your own products (developers not sharing what they are fixing?) or (2) so secretive admitting something you have might be broken and you are working on a fix! So darn frustrating...
So try iTunes 11.2 and OS X 10.9.3 updates and see if it works for you too!
Kevin

"Unsupported Cluster Configuration" status for all VM's in SCVMM 2012 R2

I have multiple Hyper-V 2012 R2 clusters that are managed via SCVMM 2012 R2. I want to make all the VM's highly available, but I receive the following errors.
VM status - Unsupported Cluster Configuration
error 13923 - highly available virtual machine is not supported by VMM because its cluster resource group is not configured correctly.
error 13706 - the host network adapter is not associated with any logical networks
I have 2 10Gb NICS teamed on all the Hyper-V Hosts. Then I create virtual switches and virtual NICS in Hyper -V. I then create separate VLANS for each virtual NIC to segment traffic for clustering, live migration, etc.
I found the following article, but it seems to just show how to identify the issue, not resolve it.
http://blogs.technet.com/b/scvmm/archive/2013/09/10/working-through-an-unsupported-cluster-configuration-scenario-in-virtual-machine-manager.aspx

Hi ok8ru12,
Thanks , it's a good article .
>>error 13706 - the host network adapter is not associated with any logical networks
According to the error , please check the setting of "Associated logical networks " of cluster nodes :
Best Regards,
Elton Ji
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] .

Password reset for all clients

Hi
I need to Reset Password on ALL clients within current system for logged on User.
Any suggestions please
Thanks
Regards

Got a Program for this. Am just pasting the code..try it
TABLES: T000, USR02.
DATA: BEGIN OF I_USR02.
        INCLUDE STRUCTURE USR02.
DATA: END OF I_USR02.
SELECTION-SCREEN BEGIN OF BLOCK STANDARD
                 WITH FRAME TITLE TEXT-001
                 NO INTERVALS.
SELECTION-SCREEN BEGIN OF LINE.
SELECTION-SCREEN COMMENT (23) TEXT-005.
SELECTION-SCREEN END   OF LINE.
SELECTION-SCREEN BEGIN OF LINE.
SELECTION-SCREEN COMMENT (23) TEXT-004.
PARAMETERS NO RADIOBUTTON GROUP RAD1.
SELECTION-SCREEN COMMENT (23) TEXT-002.
SELECTION-SCREEN END   OF LINE.
SELECTION-SCREEN BEGIN OF LINE.
SELECTION-SCREEN COMMENT (23) TEXT-005.
PARAMETERS YES RADIOBUTTON GROUP RAD1.
SELECTION-SCREEN COMMENT (23) TEXT-003.
SELECTION-SCREEN END   OF LINE.
SELECTION-SCREEN END OF BLOCK STANDARD.
MAIN PROGRAM
IF NO = 'X'.
    MESSAGE I999 WITH
     'Program Terminated at User Request'.
    LEAVE PROGRAM.
ELSE.
    PERFORM CHANGE_PASSWORD.
    SELECT * FROM T000.
      SELECT * FROM USR02 CLIENT SPECIFIED
         WHERE MANDT = T000-MANDT AND
               BNAME = SY-UNAME.
        IF USR02-MANDT = SY-MANDT.
          WRITE : 1 USR02-MANDT COLOR 6 INVERSE.
          WRITE : 5 USR02-BCODE COLOR 6 INVERSE.
        ELSE.
          WRITE : 1 USR02-MANDT COLOR COL_KEY INTENSIFIED.
          WRITE : 5 USR02-BCODE COLOR COL_BACKGROUND INTENSIFIED OFF.
        ENDIF.
        IF USR02-UFLAG = 0.
          WRITE : 24 'Not Locked' COLOR COL_BACKGROUND INTENSIFIED OFF.
        ELSEIF USR02-UFLAG = 64.
          WRITE : 24 'Locked: System Admin.' COLOR 6 INVERSE.
        ELSEIF USR02-UFLAG = 128.
          WRITE : 24 'Locked: incorrect Logons.' COLOR 6 INVERSE.
        ELSE.
        ENDIF.
        WRITE : 50 USR02-TRDAT COLOR COL_BACKGROUND INTENSIFIED OFF.
        WRITE : 61 USR02-CLASS COLOR COL_BACKGROUND INTENSIFIED OFF.
        NEW-LINE.
      ENDSELECT.
    ENDSELECT.
ENDIF.
TOP-OF-PAGE.
NEW-PAGE NO-TITLE NO-HEADING.
PERFORM LISTTITEL.
TOP-OF-PAGE DURING LINE-SELECTION.
PERFORM LISTTITEL.
      FORM CHANGE_PASSWORD                                          *
FORM CHANGE_PASSWORD.
SELECT * FROM USR02 INTO I_USR02     "grab userid and store data
    WHERE BNAME = SY-UNAME.
ENDSELECT.
IF SY-SUBRC NE 0.
    EXIT.
ENDIF.
UPDATE USR02 CLIENT SPECIFIED        "Write current client pwd over
     SET                               "other clients that have id in.
      BCODE = I_USR02-BCODE
      OCOD1 = I_USR02-OCOD1
      CODV1 = I_USR02-CODV1
      OCOD2 = I_USR02-OCOD2
      BCDA2 = I_USR02-BCDA2
      CODV2 = I_USR02-CODV2
      OCOD3 = I_USR02-OCOD3
      BCDA3 = I_USR02-BCDA3
      CODV3 = I_USR02-CODV3
      OCOD4 = I_USR02-OCOD4
      BCDA4 = I_USR02-BCDA4
      CODV4 = I_USR02-CODV4
      OCOD5 = I_USR02-OCOD5
      BCDA5 = I_USR02-BCDA5
      CODV5 = I_USR02-CODV5
      CODVN = I_USR02-CODVN
      TRDAT = I_USR02-TRDAT
      LTIME = I_USR02-LTIME
      BCDA1 = I_USR02-BCDA1
     WHERE BNAME = SY-UNAME AND
           MANDT NE SY-MANDT.          "Every client but current.
ENDFORM.                               "CHANGE_PASSWORD
      FORM LISTTITEL                                                *
FORM LISTTITEL.
    WRITE: / 'List of client(s) on which the Password for User',
            SY-UNAME COLOR COL_KEY INTENSIFIED,
           'has been reset.'.
WRITE: / 'Password originated on Client : ',
            SY-MANDT COLOR COL_KEY INTENSIFIED.
SKIP.
WRITE: / 'System: ' COLOR COL_HEADING INVERSE,
           20 SYST-SYSID COLOR COL_KEY INTENSIFIED.
WRITE: / 'Date: ' COLOR COL_HEADING INVERSE,
           20 SYST-DATUM COLOR COL_HEADING INVERSE.
WRITE: / 'Time:   ' COLOR COL_HEADING INVERSE,
           20 SYST-UZEIT COLOR COL_HEADING INVERSE.
ULINE AT (73).
WRITE: /(73) SPACE COLOR COL_HEADING INTENSIFIED.
WRITE: 1 'Cl.' COLOR COL_HEADING INTENSIFIED.
WRITE: 4 SY-VLINE.
WRITE: 5 'Encrypted Password' COLOR COL_HEADING INTENSIFIED.
WRITE: 23 SY-VLINE.
WRITE: 24 'Lock Status' COLOR COL_HEADING INTENSIFIED.
WRITE: 49 SY-VLINE.
WRITE: 50 'Last Used' COLOR COL_HEADING INTENSIFIED.
WRITE: 60 SY-VLINE.
WRITE: 61 'User Grp.' COLOR COL_HEADING INTENSIFIED.
WRITE: 73 SY-VLINE.
ULINE /(73).
ENDFORM.                               " LISTTITEL
Regards

How can standarize the settings of Firefox, by ADM is not working as it only modifies the registry, how can I configure firefox for all my users ?

I used the adm from Frontmotion but it only works with the FirefixCE version, I need to force Firefox configuration in my domain with a standar version of Firefox, how can I do this, it could be by GPO or logon script

Most YouTube content requires the Flash plugin. Sometimes it's necessary to uninstall then reinstall that plugin.
Uninstall the Flash plugin then reinstall new > Troubleshoot Flash Player | Mac OS
Very important to uninstall the currently installed plugin first.
Now launch Safari and try a video.
If you have the ClickToFlash extension installed, that can prevent Flash based video from streaming. It can also be installed as a plugin in /Library/Internet-Plug-Ins.
And check to see if Safari is running in 32 bit mode. Right or control click the Safari icon in your Applications folder then click Get Info. If the box next to: Open in 32 bit mode is selected, deselect, quit then relaunch Safari.
You may also need to delete the cache associated with Safari .
Open the Finder. From the Finder menu bar click Go > Go to Folder
Type or copy/paste: ~/Library/Caches/com.apple.Safari
Click Go the move the Cache.db file from the com.apple.Safari folder to the Trash.
Quit and relaunch Safari. Try a video.

Configure "Always hide forms document message bar" and "Do not show edit warnings" for all users?

We need to do a mass deployment of Adobe Reader XI 11.0.3 with "Always hide forms document message bar" preference setting automatically set for every user so they do not have to go through the menu and set it manually.
Is there a way to configure this for all users with the customization wizard or another method?
We also need to do the same for "Do not show edit warnings"
If these are registry keys, which registry keys set these options?

Try http://www.adobe.com/devnet-docs/acrobatetk/tools/PrefRef/Windows/DocumentStatus.html?zoom _highlight=message#idkeyname_1_5647.
If that doesn't work and there's a configuration item in the preferences UI, do this:
Get regshot.
Close everything but Acrobat/Reader.
Take a reg shot.
Configure the setting via the UI.
Tak another reg shot.
Compare the two.
That process will give you your answer.
If there is no corresponding pref in the UI, then you probably can't do it.
Ben

How to Change proxy settings/homepage for all users in my system at a time?

Need single configuration file for all users

You can set up a system cache for sharing jars: See here: http://java.sun.com/j2se/1.5.0/docs/guide/javaws/developersguide/enterprise_config.03.06.html

Configuration Guideline for RE-FX (flexibel real estate)

Hi
I'm having problems with the configuration of RE-FX, one of my problems is with integration of PSCD.
Those anyone have a configuration guide for all re-fx or to a part of it?
Kind Regards
Marta

SAP Note: 1003497 - Release note about integrating RE-FX with PSCD.

How to change default action "alarm" for all signatures ?

My question belongs to a Cisco 1712 (128 MB, IOS 12.3T, SDM 2.5 installed):
I'm trying to change the default action "alarm" to "alarm,reset,drop" for all signatures of my custom set.
However doing so via SDM fails. First, it appears as being done correctly, but after compiling the signatures again, the default values are back there (in the same sense, I was unable to delete signatures, works just using the CLI).
I followed the instructions at cisco.com:
router(config)#ip ips signature-definition
router(config-sigdef)#signature 6130 10
router(config-sigdef-sig)#engine
router(config-sigdef-sig-engine)#event-action produce-alert
router(config-sigdef-sig-engine)#event-action deny-packet-inline
router(config-sigdef-sig-engine)#event-action reset-tcp-connection
router(config-sigdef-sig-engine)#exit
However ip ips signature-definition is not understood by the router, so the procedure fails.
Can you please assist me ?

You can use IOS command-line interface (CLI) to change signature actions for one signature or a group of signatures based on signature categories. The following example shows how to change signature action to alert, drop and reset for signature 6130 with subsig ID of 10.
router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
router(config)#ip ips signature-definition
router(config-sigdef)#signature 6130 10
router(config-sigdef-sig)#engine
router(config-sigdef-sig-engine)#event-action produce-alert
router(config-sigdef-sig-engine)#event-action deny-packet-inline
router(config-sigdef-sig-engine)#event-action reset-tcp-connection
router(config-sigdef-sig-engine)#exit
router(config-sigdef-sig)#exit
router(config-sigdef)#exit
Do you want to accept these changes? [confirm]y
router(config)#

Configure "reset" for all default signatures

Similar Messages

Maybe you are looking for