Configure the syslog of ASA 5512-X for display on Cisco Prime Infrastructure 2.1

Hi, I'm working on implementing the Cisco Prime Infrastructure 2.1 and want to display the syslog about ASA5512-X with Software Version 9.2.
What would be the procedure for configuring?
Thanks in advance.

Hi,
Enable "logging host x.x.x.x " command to enable logging
check the below link:
http://www.cisco.com/c/en/us/td/docs/security/asa/asa91/configuration/general/asa_91_general_config/monitor_syslog.html#68764
FYI: Prime Infrastructure support only SEV 0,1,2 syslogs as of now.
Operate > alarm and events > syslogs
Thanks-
Afroz
****Ratings Encourages Contributors *****

Similar Messages

Replicate in the Master controller and creation of new user with cisco prime infrastructure 2.1.

Hello!!
We have multiple controllers Cisco WLC 5508 (all running software version 7.6.120.0) distributed in various buildings and a controller in other control building (also Cisco WLC 7.6.120.0 5508) operating as Master and backup of the buildings's controllers .
Each building is radiated such an SSID that is used as a validation of the user connected to that SSID web portal each controller (in the WLAN, Security -> Layer 3 -> Web Policy), using the local database to validate the user.
The problem is that the local database of users is not being replicated between controllers buildings and the Master controller, so if you drop the controller of a building, the Master controller begins to provide service to the buildings access points, but the equivalent radiated SSID cannot able to validate users.
I need know if it's possible through Cisco Prime Infrastruture 2.1, first replicate in the Master controller on the basis of existing controllers buildings each local data and, second, that the creation of new users are automatically perform both the controllers like to the Master .
Thanks.

As noted earlier, it is not advisable to use the root user to log in for normal use. New users and groups can be created by navigating to Administration > Users, Roles & AAA as shown in the preceding figures. It would help to chalk out what are the various levels at which you want to distribute the users, and to create those roles first. It doesn’t really matter whether you create users or groups first. New users can be easily added by going to Administration > Users, Roles & AAA > Users > Add Users > Select “Add Users” from the drop-down on the right side. Once you get into the add user workflow, fill in the username, password, and local authorization for this user as shown in the figure below.
A virtual domain can also be assigned to the users when you define their roles by selecting the virtual domain on the left side and moving it to the right side as shown in the image below (left).

Apple Configurator: The spreadsheet provided has redemption codes for "(null)."

I'm trying to import a spreadsheet of redemption codes into Apple Configurator. I download the spreadsheet directly from https://vpp.itunes.apple.com, but when I try to import it, I get the following message:
Apple Configurator: The spreadsheet provided has redemption codes for "(null)."
What can I do to import it?

I've got support from Apple Germany. It seems to be a problem of version 1.1.2 of Apple Configurator and Mountain Lion 10.8.2
As mentioned above I had the same problem using 10.7.4 and 10.7.5 and Configurator 1.1.2. Apple Germany sent me a different spreadsheet, where I've put my codes in and it worked. Strange but true.
Other story, I bought 50 redeem codes, after installing 22 iPads it stopped, telling me that there are no more redeem codes left ?
Good luck contacting Apple directly

What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP's?

What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP’s?

• PI provides visibility for autonomous clients within the same list view as lightweight and wired clients (client list page).
• Rogue AP detection for autonomous AP's is not supported (it's supported in CUWN).
• Alarms/events for client authentication issues (e.g. authentication failure) are displayed in PI.
• Config management for autonomous AP's is via CLI template. Config comparison and archiving functionality in PI leverages these same features that were brought in from LMS, so need to defer to others in terms of whether this is a cross-platform feature in PI or is only supported on a subset of platforms. Config comparison/archive is supported in CUWN.PI supports both infrastructure (e.g. AP Tx Power and Channel, busiest AP, AP utilization, etc.) and client (e.g. client count, client sessions, etc.) reports, and there are extensive reports for CUWN

Cisco Prime Infrastructure 2.0 and Cisco ASA

Hello,
We've recently installed trial version of Cisco Prime Infrastructure 2.0 Express. We hoped that it already supports Cisco ASA 55xx series (especially 5505, we have pretty amount of them). But we had some problems with PI and asa durind the exploitation process.
First, I've added ASA to PI, and Inventory Collection Status is Completed, but I can't see CPU and RAM utilization graphs. Inventory.logs are non-informative.
Also, config backup is success, but when I try to watch the backuped configuration at Configuration Archive PI says "Failed to fetch raw configuration". And so on.
ASA version is 5505, image is 9.1(2).
So, I have a question: is it possible to manage ASAs with PI 2.0?
UPD: I've just tried to upgrade asa to 9.1(4), and behavior of the equipment is quite the same. Seems we shall wait for 9.2 to be released.

Have you downloaded and applied the latest Device Pack updates?
PI enhanced ASA support after the initial 2.0 release and the Device Packs incorporate that change.
The README file for Device Packs explains how to install them. (A bug currently does not allow the direct download in PI so you need to follow the method for installation from local storage after you manually download. Here is a link to the download location.

Monitoring ASA in Cisco Prime infrastructure 2.2

Hi everybody. I have some issue with cisco Prime Infrastructure 2.2. We use this product in our network for monitoring network devices and I need to monitor also our ASA 5550 device with soft 8.4. I added ASA to Cisco PI but see only basic component like my device can reachable via and read via snmp. But cannot see CPU, RAM, Device ENV like Temperature, l2l vpn connection, Interfaces status and Utilization that interfaces, cannot see sub interface that placed on ASA like that g0/0.20. I need fully monitor ASA and See logs and trap for my device:
CPU RAM ENV (Temperature), Interface and sub interface status, L2L VPN Status.
1 Cisco Prime infrastructure can full support ASA for monitoring and logging.. IF YES how can i configure that features in Cisco PI 2.2 for ASA
2 IF not which product Can full support that features for full monitoring and logging ASA devices
I have a little deadline for finishing
thanks everybody before

I've not success monitoring ASA interface utilization either. I'm using PI 2.2 with device update #1. The ASA is a 5585-X with 9.2(3) software.
I have deployed the PI monitoring template to the ASA and do see its overall status and PI has enumerated the interfaces in the device page.
I even looked at a packet capture and see PI querying the values of the interface counters and those values being sent back to PI - yet I cannot select any ASA interface when drilling down under Performance Detail monitoring.
When I get some free time I will open a TAC case on it, meanwhile I am getting all the info I need from the upstream and downstream switches.

User Name and Password for Cisco Prime Infrastructure 2.1

Hi all:
I am stuck at the login page of Cisco Prime Infrastructure 2.1.
I have tried using the user name root and its password (when log in with root at Vsphere Client) and also the login user name "before" get into the appliance infrastructure, all cannot work.
Anybody knows what is the default username or password or any way to set the username and password for this Cisco Prime Infrastructure 2.1 website?
Thanks!
tangsuan

Hi Tangsuan,
Following is the documented procedure for password recovery..
In order to modify the GUI root user password, you will need to login to the NCS CLI
as an admin user, and enter the command
"ncs password root password <new password>" (without the quotes)
This should set the web interface root user password :
http://www.cisco.com/en/US/docs/wireless/ncs/1.1/configuration/guide/manag.html#wp1268889
If you have lost your CLI password , try the default logging that is ,
CLI user is admin and not root, so please try logging in as admin with
the password that was set during setup. If that does not work , you need
the install disk that came with the appliance to recover that password.
Follow these steps:
Recovering a Lost Admin Password
If you lose or forget the admin password for NCS appliance, follow these steps.
Step 1 Reboot the NCS appliance with the ISO DVD inserted. The Cisco Prime Network Control
System Welcome screen appears:
ISOLINUX 3.11 2005-09-02 Copyright (C) 1994-2005 H. Peter Anvin
             Welcome to Cisco Prime Network Control System
To boot from hard disk, press <Enter>.
Available boot options:
   [1] Network Control System Installation (Keyboard/Monitor)
   [2] Network Control System Installation (Serial Console)
   [3] Recover administrator password. (Keyboard/Monitor)
   [4] Recover administrator password. (Serial Console)
<Enter> Boot existing OS from Hard Disk.
Enter boot option and press <return>.
boot:
Step 2 Select the desired recovery option, 3 or 4, depending on how you
are connected to the appliance and then follow the prompts.
Thanks-
Afroz
***Ratings Encourages Contributors ****

Ask the Expert: Cisco Prime Infrastructure - Implementation and Deployment

Welcome to the Cisco Support Community Ask the Expert conversation.
This Ask The expert Session will cover questions spanning Cisco Prime Infrastructure on Implementation and Deployment on Wired and Wireless. This will be more specific to Customer’s and Partners questions product covering PI on configuration, Features and Menu, Network Monitoring, Maps, Implementation, High Availability and Maintenance and t/s parts.
Monday, February 2nd, 2015 to Friday, February 13th, 2015
Dhiresh Yadav is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco Prime Infrastructure and Cisco Wireless products. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS) and CCIE (DC) certifications.
Afroz Ahmad is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco NMS products like Prime Infrastructure, LMS, IP SLA and SNMP etc. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS),CCIE (DC), and SCJP (Sun Certified Java Professional )
Vinod Kumar Arya is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco NMS products like Prime Infrastructure, LMS, IP SLA and SNMP etc. He has over 8 years of industry experience working with large enterprise and service provider networks. He also holds VCP 5 and RHCE certifications.
** Remember to use the rating system to let the experts know you have received an adequate response.**
Because of the volume expected during this event, the experts might not be able to answer every question. Remember that you can continue the conversation in the Network Infrastructure community, > Network Management, shortly after the event. This event lasts through February 13th 2015. Visit this forum often to view responses to your questions and those of other Cisco Support Community members.

Hello Wilson,
Thanks for joining us.
1841 should just work fine for net flow . Hope you have a valid "PI Assurance license" installed on the server.
"PI Assurance license" is required for "net-flow" feature
Devices supporting Netflow in PI ::
1400, 1600, 1700 & 1800
2500, 2600 & 2800
3600, 3700, 3750 & 3800
4500 & 4700
AS5300 & 5800
7200, 7300, 7400 & 7500
Catalyst 4500 ASCI
Catalyst 5000, 6500, & 7600 ASCI
ESR 10000 ASCI
GSR 12000 ASCI
Cisco IOS Software Release Version
Supported Cisco Hardware Platforms
11.1CA, 11.1CC
Cisco 7200 and 7500 series, RSP 7200 series
12.0
Cisco 1720, 2600, 3600, 4500, 4700, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series
12.0T, 12.0S
Cisco 1720, 2600, 3600, 4500, 4700, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8600 series
12.0(3)T, 12.0(3)S
Cisco 1720, 2600, 3600, 4500, 4700, AS5300, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8650 series
12.0(4)T
Cisco 1400, 1600, 1720, 2500, 2600, 3600, 4500,
4700, AS5300, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8650 series
12.0(4)XE
Cisco 7100 series
12.0(6)S
Cisco 12000 series
NetFlow is also supported by these devices Cisco 800, 1700, 1800, 2800, 3800, 6500, 7300, 7600, 10000, CRS-1 and these Catalyst series switches: 45xx, 55xx, 6xxx.
NetFlow export is also supported on other Cisco switches when using a NetFlow Feature Card (NFFC) or NFFC II and the Route Switch Module (RSM), or Route Switch Feature Card (RSFC). However, check whether version 5 is supported, as most switches export version 7 by default.
You can check the below steps to diagnose the issue::
To verify that NetFlow is exported from a device to PI, follow the steps below:
1)   Browse to Administration > Data Sources page. Check the value in column ‘Last Active Time’ for the ‘Device Data Sources’ table. If the table is empty or the value does not represent recent time, then
it is possible that the device is not exporting NetFlow or PI Assurance license is not applied / expired.
2)   Login to PI console ( via SSH) as root user and run the command:
                netstat –an | grep 9991 – Output of this should be like : udp        0      0 :::9991         :::*
                Check the firewall settings on PI server using the command: firewall -L
1)   Check the configuration on an IOS / IOS –XE device. Run the commands
a)   sh running-config | inc destination
1)   This should list the IP address of the PI SERVER ( along with other outputs if any)
b)   sh running-config | inc 9991
1)   This should list at least one entry.
c)   If the above are fine, then verify that the flow monitor, flow exporter and the flow records are correctly configured on the device.
Refer to the URLs below to configure NetFlow export.
http://preview.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/user/guide/setup_monitor.html#wp1056427
Thanks-
Afroz
***Ratings Encourages Contributors ****

Is cisco prime infrastructure support / can be run as syslog server?

Dear All,
is cisco prime infrastructure support / can be run as syslog server?
and,
where i can see network topology diagram, using cisco prime infrastructure?
many thanks,
Jerri

Hello. Cisco Prime LMS will be replaced by Cisco Prime Infrastructure in the near future.
In the current release of Cisco Prime Infrastructure you can't use topology diagrams. This feature is in roadmap.
About syslog, you can send syslogs to Cisco Prime Infrastructure, but I don't recommend using it as syslog server. Please see this link for more information https://supportforums.cisco.com/thread/2179520
Please rate if this helps

Cisco Prime Infrastructure 1.3, Mail Configuration

Hi,
I have a Cisco Prime Infrastructure 1.3 and I want to set up the mail. When I test it, I get this error:
Failed to send mail to primary SMTP server. Failed to send mail to secondary SMTP server. Please make sure that you save mail configuration by hitting 'Save' button.
I have the ip address, and the username and password. Do I need to create a new buzon for the prime? because by default the "From" field appears with
[email protected]
Thanks!!

Some extra info that has just come to my attention. At one point we were running (we're actually still running) CiscoWorks with LMS3.2 and Cisco NCS 1.x. I merged these two things together into Cisco Prime Infrastructure (upgraded the licensing to get 450 lifecycle licenses to cover the APs + all of the devices coming from LMS3.2). I followed all of the documented procedures to upgrade the NCS appliance to Prime Infrastructure. But when I type "show application" from the CLI of the NCS appliance (now the Prime Infrastructure appliance) I see this:
HQ-NCS1/admin# show application
NCS Cisco Prime Network Control System
Is that normal? Maybe this is my problem. Should this output list "Cisco Prime Infrastructure" instead of (or in addtion to) Cisco Prime Network Control System? When I login to the GUI it shows "Cisco Prime Infrastructure" and the GUI has changed considerably (menus are different) so I'm assuming that the application upgrades I launched from the CLI to go to Prime Infrastructure worked fine.

Cisco Prime Infrastructure automatic configuration Archieve

Hi all,
I installed Cisco Prime Infrastructure and I note that it make configuration archieving for all devices on it with different date.
I need to know based on what it selects the date on which it take the archieving of configuration (note that it takes archieving of all boxes on different dates) ??
thanks,
Best Regards.

Hi Mohamed,
The configuration archive will run every day, however if there is no change between today's configuration and the previous check, there is no point in archiving it again.
Best regards,
Vlad
==========
NMS Team
Krakow, Poland
Cisco TAC

Cisco Prime Infrastructure 2.0 and ASA 55xx platform problem

Hello,
We recently upgraded to Prime Infrastructure 2.0 with the hope being able to manage our ASA's from PRIME (and complete an LMS migration).
When I attempt to add ASA's to prime i get the following collection errors:
Unable to collect processor and RAM information.          Processor and RAM information.          Unexpected error. See the log file inventory.log for details.
In the logfile I get the following XML parsing error on the MIB:
<palError>
<deviceId>6284310032</deviceId>
<code>VALIDATION_ERROR</code>
<message>Failed to validate output XML: cvc-maxInclusive-valid: Value '3484331296' is not facet-valid with respect to maxInclusive '2147483647' for type 'int'.</message>
<result>
    <result xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="/CISCO-MEMORY-POOL-MIB/xmp-im-file-system-module.xsd">
      <xmp-im-file-system-module>
        <MemoryPoolStatistics>
          <memoryPoolIndex>1</memoryPoolIndex>
          <free>4294967295</free>
          <largestFree>4294967295</largestFree>
          <used>3484331296</used>
        </MemoryPoolStatistics>
To me it seems that the ASA returns a value that is bigger then int32 and thus causes an overflow? Any clues? Workarounds to add an ASA to Prime without checking these MIB'S?
Regards,
Marcel

Hi,
does anyone happen to know if that problem is fixed? My currently setup looks like this:
1. Cisco Prime Infrastructure 2.1 with updated device pack.
2. Assurance license
3. ASA5510 which has enabled netflow. Netflow is being sent to Cisco Prime 2.1
I do receive netflow raw data within Cisco Prime 2.1 but any graphical display of netflow data is not working. Does anybody has an idea where the problem is? Could it be that the graphical data is only displayed when sending netflow 1, netflow 5 or netflow 7?
regards
Maurus

A job in Cisco Prime Infrastructure 2.1 has been running for 50 days

I found a job (SAM_Poller_22_15_GETVPNPoller_1878262177) in cisco prime infrastructure 2.1 (Administration -> Job Dashboard -> System-defined), which has been running for about 50 days. Is this normal? How can I stop it? Thanks for any help..
SAM_Poller_22_15_GETVPNPoller_1878262177
PollerJob
In-Progress
Running
2014-09-19 01:28
49 Days 01 : 28 : 37

Not normal, seems to be stuck. Try to stop (ncs stop) and start (ncs start) the system processes, which should stop this job.
If it happens again, i would recommend to open a TAC case for further investigation.
-Thanks
Vinod

Is it possible to manage the switch SMB 300 series using Cisco Prime Infrastructure?

Is it possible to manage the switch SMB 300 series using Cisco Prime Infrastructure 1.2?

SF300 series is targeted for support in PI 2.0.

User Tracking supported for Nexus 5K in Prime Infrastructure 1.3

Hi,
Is User Tracking supported for Nexus 5K in Prime Infrastructure 1.3?
Regards
Francois Bouchard

Hi Andy,
Check the below link , as per this Doc .. User tracking is supported in 2.0:
http://www.cisco.com/en/US/prod/collateral/netmgtsw/ps6504/ps6528/ps12239/guide_c07-729089.html
Thanks-
Afroz
[Do rate the usefu post]

Configure the syslog of ASA 5512-X for display on Cisco Prime Infrastructure 2.1

Similar Messages

Maybe you are looking for