Configure Ultra 10 with D1000

Hi
I running Solaris 10 on ULTRA 10 installed.I want to configure D1000 with ULTRA 10.I inserted scsi diff card(x6541) in slot.I hooked up D1000 with Ultra 10, but the system does't see disk array.
I tried with devfsadm amd boot -rv.
THANKS..........

hi
I can see disks at probe-scsi-all, but it won't show at format. when i boot with boot -r command it show me,
Cofiguring devices:
WARNING: /pci@1f,0/pci@1/scsi@2,1 (glm3):
Invalid reselection -bad tag (0.0)
/pci@1f,0/pci@1/scsi@2,1 (glm3):
got SCSI bus reset
the it goes on
/pci@1f,0/pci@1/scsi@2,1 (glm3):
connected command timeout of Target 1.0
/pci@1f,0/pci@1/scsi@2,1 (glm3):
got SCSI bus resset
then this goes on.
How do fix this bad tag .............

Similar Messages

Sun Ultra 10 with SunStorEDGE A1000/D1000 unable to setup

I realise this covers old ground but I have not been able to trace a uitable resolvement and would be grateful for assistance.
I have a Sun Ultra 10 with 256MB RAM and 440GHz cpu.. It has a pci Adaptec 2944UW HVD SCSI interface card. The storage system is a tray of eight scsi 72GB disks housed in a D1000 case. NetBSD reported it as an A1000 SunStorEDGE at sd0 having 16 targets and 8 luns. However NetBSD did not have a readily available controller to setup the raid system so I installed an alternative. I presume the case is a reused old case housing an A1000 unit.
I tried to format the drives directly but they are not lists as devices such as ct1sd1 etc. and so this is not possible.
I have installed Sun Solaris 10 but could not communicate and reported inability to use rdriver and rdnexus and after reading a number of reports that driver hooks had been removed from the kernel in Solaris 10 I have installed Solaris 9.
On both occasions I installed a number of RAID Manager 6.1.1 control packs, namely SUNWosafw, osar, osau, osamn and vtsse direct from my CD here.
I commanded dr_hotadd.sh to take up the challenge but it failed to communicate.
I added a number of Rdac amendments to rparams in /etc/osa but this did not resolve the issue.
I have tried to call probe-scsi-all after doing a reset-all from the OBP but this fails to report anything. I presume this is because the unit is connected by the interface card rather than a direct scsi disk.
dmesg pipe grep scsi reports:
unknown scsi sd0 at uata0 target 2 lun 0
I would be very grateful fr guidance to resolve this connection so that I can create a suitable filestore.
Thanks
c

blackfoot wrote:
I realise this covers old ground but I have not been able to trace a uitable resolvement and would be grateful for assistance.
I have a Sun Ultra 10 with 256MB RAM and 440GHz cpu.. It has a pci Adaptec 2944UW HVD SCSI interface card. The storage system is a tray of eight scsi 72GB disks housed in a D1000 case. NetBSD reported it as an A1000 SunStorEDGE at sd0 having 16 targets and 8 luns. However NetBSD did not have a readily available controller to setup the raid system so I installed an alternative. I presume the case is a reused old case housing an A1000 unit.If it's really an A1000, you won't have access to the drives. You'll only see exposed LUNS from the raid controller. Do you have a dial in the rear with a scsi address? That will be the address that the A1000 will respond on. In addition, the A1000 has only one pair of SCSI ports. The D1000 has two pair and doesn't have the scsi adress dial (because each of the disks in the chassis respond on their own addresses). Instead you have some DIP switches to change the addressing behavior.
I tried to format the drives directly but they are not lists as devices such as ct1sd1 etc. and so this is not possible.
I have installed Sun Solaris 10 but could not communicate and reported inability to use rdriver and rdnexus and after reading a number of reports that driver hooks had been removed from the kernel in Solaris 10 I have installed Solaris 9.That's fine. You can ignore them. Neither the A1000 nor D1000 require those drivers. You should still be able to use 'rm6' or the CLI tools to interact with an A1000.
On both occasions I installed a number of RAID Manager 6.1.1 control packs, namely SUNWosafw, osar, osau, osamn and vtsse direct from my CD here.
I commanded dr_hotadd.sh to take up the challenge but it failed to communicate.
I added a number of Rdac amendments to rparams in /etc/osa but this did not resolve the issue.
I have tried to call probe-scsi-all after doing a reset-all from the OBP but this fails to report anything. I presume this is because the unit is connected by the interface card rather than a direct scsi disk.If the controller doesn't support the OBP environment, then yes, you won't see anything then.
dmesg pipe grep scsi reports:
unknown scsi sd0 at uata0 target 2 lun 0So that might be a single LUN from an A1000 controller. If the selector switch in the back is set to '2', then it's even more likely.
Darren

Doesn't play songs, "itunes is not configured for use with mac-formatted"??

Hi, new ipod shuffle. Seems to charge fine, all indicator lights function as expected. Everything looks fine in itunes. But it doesn't play songs. I have the most recent versions of itunes and the ipod software. Re-set, updated, and restored, nothing works. Even restored using the restore utility. Re-started computer. Checked for volume control. Won't play songs. Tried different file types. Songs play fine from itunes library and from the device's library within itunes. Tried different headphones. Hooked it up to computer speakers. Turning volume all the way up on device and speakers, heard some very faint rhythmic static, so my guess is the jack socket (or whatever you call it) is just messed up, but it seems weird that it can transfer power and data to the device but doesn't work for sound...
The only other issues that have come up is that the drive disappears in explorer once it syncs with itunes. Other people who've noticed this seem to have completely different problems so I don't think it's related.
Also, I have MacDrive on my computer. And when it starts up with the ipod plugged in, MacDrive offers the message "Itunes is not configured for use with Mac-formatted ipods." It offers to automatically reconfigure itunes so it can read mac-formatted ipods. Since I've restored the device, I don't see why formatting should be an issue so I say "no."
Should I try letting macdrive do its format thing? Should I try formatting the ipod disk on the My Computer menu? Or should I just email apple and tell them the jack's busted?
Thanks for any thoughts!

Well, I have had my iPod for about 3 years, it is a 4th generation non-video 40 GB. One day it just stopped working, and now it does not play any songs. when I turn it on it makes this odd whirring sounds that computers make when they try really hard to do something. I cannot charge it, and it is not recognized by iTunes. Also when I turn it on, I get the apple.com/ipod/support (or whatever it is) screen. Needless to say, my warranty is expired, and so I cannot do anything for it except get a new battery, or buy a new one. Is there any way to fix this problem, or anyone out there who is experiencing the same thing?
I'm having the exact same problem with my wife's iPod. However it will play about 3 seconds of a song and go onto the next song.
If there is anyone out there that can help please do!
Windows XP

Who can run in ultra turbo with low cas ramm. read pls..ill explain

This doent pertain to overclocker casue if you go over 219 fsb on 800 fsb pcu it disables mat..
Who here with an 865, 875 mobo can run 2 or 2.5 cas timings in ultra turbo with less then 215 FSB.
If so which brand ramm and what bios and board do you have .
I am about to order ramm thats iss 3-3-3-8 but i would rather get the corsair xmas which is 2-3-3-6 if id be able to run it in ultra turbo..
what do you think and all responses definately appreciated.....

Quote
Originally posted by billy
and i might be wrong is that is you disabled speed from ayto it disables mat but im unsure..
All i know is that before i flashed my bios on my old pcb, all was wel in ultra turbo ..
After the flash couldnt do it anymore regardless of old flash and msi on the phone for 2 hours....
I think the 875 p has some hidden number which it calculates as being dafe or not, if your memory regardless of what timings you set it at reads lower then it thinks safe you will crash at boot.
Thats why i am making all this hype about memory . I cant afford to rMa belive you me i want that corsair twinx1024-3200cpt thats listed in the ramm module spec. Only thing is how to tell if its version 1.1 like they ask . I dont think version 1.1 is abtainable. this is referring to the ramm list for the neo 875 fisr pcb 2.0 . Also it lists ocz but which one do i get..
From what you are telling me, is anyone will work and to get2-2-2-5 if i can , but i think there might be a catch to this when the boards reads it. Im unsure. If so how to fake out the bios and let your manuel timings stick.
On my last boord after the flash , even when i flashed back i after loading default and running onece i restarted and set them to 3-4-4-8 and if i even went from slow to fast i could not boot. This only hapened in dual mode. In single i could hit ultra turbo....
remarks lol... If you know a way around this... also if you can tell me about that corsir ramm listed in the fisr's list. i can buy it but how do i know its v1.1 lol...
no, MAT can be still enabled with SPD disabled. for example i have the performance mode enabled, but i set my RAM timings manually. but i said that before, you must have missed it...
i didnt understand what you were trying to say here, your english is pretty weird. 2-2-2-5 timings can be done only with the new Corsair XL memory, and only under 215MHz. this kinda "is" the ultra turbo mode i guess, because you cant tighten the timings anymore.
and as that other guy said, 2-3-2-6 rated memory is always a safe bet as far as compatibility is concerned, from Kingston, Corsair or whoever. the new BIOS version dont have any problems with that from my experience.
as i said, i dont understand your other questions, but i hope your memory issue is solved.
Quote
I'm not going to bother reading what everyone else posted, I have that 2-3-2-6 rated memory from corsair, and I run ultra-turbo. N/P
with SPD enabled or disabled? im just asking because i cant set MAT to ultra turbo with SPD setting the memory timings. Turbo is the best i can do here.

I have a Symphonic 32' HDTV (Dolby Digital Plus). can someone help me figure out how to configure it optimally with my Mac Mini? the display and sound is off. Do I need drivers/software? I'm new to macs.

I have a Symphonic 32' HDTV (Dolby Digital Plus). can someone help me figure out how to configure it optimally with my Mac Mini? the display and sound is off. Do I need drivers/software? I'm new to macs.

Hello, since nobdy else has replied...
Long shot, but...
Open Audio Midi Setup in Applications>Utilities, see the input & output options & KHz setting there.

Boot data configuration missing or with errors

I have a Satelllite L870-15W, and no way to turn the system on.
All it says is "Toshiba" (the welcome screen) and then (after having pressed f8 or f9):
file: efi/micorsoft/boot/bcd,
status 0x0000001;
the boot configuration data for your or is missing or contains errors.
I have only recovery partition at D: but cannot access it. What shall I do?

Satellite L870-15W (PSKFNE-00700CHU) <- Hungarian version
Spec here too.
boot data configuration missing or with errors
It probably means the BCD is missing or corrupt.
To repair this, you need to access the recovery environment. Microsoft says Windows 8 will eventually take you there if it fails to boot many times. You can also get there using a System Repair Disc or a Windows 8 installation DVD like this downloadable one. You need the 64-bit disc.
It's possble this will also work on your Toshiba machine. Restart the computer by pressing the power button and immediately start tapping the F12 key until the Boot Menu appears. Using the arrow keys, select <HDD Recovery>.
WinRE looks like this. Select Troubleshoot and then Advanced options.
Lots of things to try. See KB2622803 for boot sector problems. The article assumes Windows Vista/7. The same fixes look different in Windows 8, but are all available.
If Automatic Repair (Startup Repair in 8.1) and System Restore fail, use the bootrec tool at the command prompt. This applies to Windows 8 also.
   Use the Bootrec.exe tool in the Windows Recovery Environment to troubleshoot and repair startup issu...
Don't give up until you have tried replacing the BCD itself as follows. (Sometimes the partition is not named "c" and you need to try another letter.)
   c:
   cd boot
   attrib bcd -s -h -r
   ren c:\boot\bcd bcd.old
   bootrec /RebuildBcd
-Jerry

How to configure bt mail with icloud?

how to configure bt mail with icloud?

iCloud does not handle any mail systems except for its own. BT is not an iCloud mail system, so you can't.

Configure airport express with mac book air

I am trying to configure airport express with a Mac Book Air, without success; the program is installed, but then, nothing appears to configure Airpor Express...
Can I get any help? Thank you
António

Hello!
I´m sorry it took so long to reply, but I´m new to these blogs; and I´ve been travelling a lot... Anyway, I was able to configure Airport Express, but I was told I could use it to expand my wireless network inside my house; which I found it´s not possible.
So, I´m returning my Airport Express to the store tomorrow and try to figure out a way to extend my wireless in any other way.
Any sugestion? Big houses are a problem...
Best regards, and once again thank you!
Antonio

I am using elements 11. I cannot open editor because configuration error occurs with message "errror 213:11". What happened? What can I do? Thanks a lot for your support.

I am using elements 11 with Windows7. I cannot open editor because configuration error occurs with message "errror 213:11". What happened? What can I do? Thanks a lot for your support.

See if this helps:
Error "License store does not allow writing" | Install log | CS5, CS5.5

Configuration assistant error with Oracle 10g 10.2.02 with Solaris 10 6/06

Hi all,
As anyone seen this a fix for this error?
I have installed Solaris 10 6/06 x86 on VMWare 5.2 which works fine.
When I attempt to install Oracle 10g 10.2.02 for Solaris x86 (released in Sept 06), the install goes fine until I get to the configuration assistant stage.
The first Net based configuration assistant fails with a Java exception which seems to be related to a Sig 11 in the libc library.
This looks like an error fixed by a patch mentioned in the release notes but the patch does not seem to be available for this version of Solaris.
Any comments would be greatly appreciated...
Regards
Anthony

Hi all,
Just to update this.
I have deselected the create database option part of the install and Oracle installs OK!
The problem is in the create database phase which I have manually done when I use the dbca program.
When I get to the create database operation of the the dbca wizard, I get a the following error "ORA-00600, internal error code, arguments [kelntf-ldminit, [146],[1],[],[],[],[],[]"
Any offers?

Configure sharepoint 2013 with Microsoft exchange 2010

Hi,
I am want to configure SharePoint 2013 with Microsoft exchange 2010.
Please let me how can I integrate these server to Send/ Receive domain E-mails.
Thanks,
C Mahone

For email integration there really isn't anything special about Exchange 2010 vs. any other mail server. Check the links here on configuring Incoming and Outgoing mail in SharePoint:
http://technet.microsoft.com/en-us/library/ee956941(v=office.15).aspx
Paul Stork SharePoint Server MVP
Principal Architect: Blue Chip Consulting Group
Blog: http://dontpapanic.com/blog
Twitter: Follow @pstork
Please remember to mark your question as "answered" if this solves your problem.

Can't configure Airport Extreme with IP 192.168.0.1 after software update

Hi there,
after updating my ax with utility software 5.3.1 and firmware 7.3.1. The software didn't allow the dhcp configuration to stay at IP range from 192.168.0.40 to 192.168.0.200
The message said that this is not a valid IP.
The configuration was working before without any problem.
After several tries I changed to 192.168.1.40 and 192.168.1.200. Now I was able to save the changes. And the airport is working well.
But I can't go back to 192.168.0
But I need to use 192.168.0 for a tunnel to connect to my wifes company.
Configuration:
Seperate Modem with DSL.
Connecting over PPPoE
Activeted WLan
Connected computers over Lan and Wlan
Can anybody help?
Thanx
Stephan

by-feet, Welcome to the discussion area!
AFAIK the AirPort Extreme base station (AEBS) has always forced the 3rd digit to be a 1 (one), as in x.y.1.z.
Could it be that you previously had the AEBS to operate as a bridge and your "modem" was actually suppling the IP addresses?

Can't configure airport express with laptop after 10.5.6 update

I can't configure airport express with laptop after 10.5.6 update
the airport express is seen but can't access configuration screen, I get the spinning wheel forever.
Other computer gets to the configuration screen without problem.
And the airport utility describes the airport express like this: syAP.802.11format

I downloaded the airport utility and re-installed
and the problem was solved

Configuration of UWL with Abap webdynpro

Hi,
We are doing configuration of UWL with Abap webdynpro. Our purpose to launch Abap webdynpro application , once clicked to a worlitem in UWL iView. we are unable to do due to following errors.
We have done in this way.
1.Created ECC system in EP
2.register the uwl.webflow
3.create ABAP iview(for test purpose still getting error when preview) (N/A)
4.clear cache
4.import xml file
<ItemType name="uwl.task.webflow.TS91000006.UWLECCCLNT530" connector="WebFlowConnector" defaultView="urliview" defaultAction="viewDetail" executionMode="pessimistic">
      <ItemTypeCriteria systemId="UWLECCCLNT530" externalType="TS91000006" connector="WebFlowConnector" />
      <Actions>
        <Action name="launchWebDynProABAP" handler="SAPWebDynproABAPLauncher">
          <Properties>
            <Property name="WebDynproApplication" value="em_wipm_app" />
            <Property name="WebDynproNamespace" value="kgo" />
            <Property name="System" value="UWLECCCLNT530" />
            <Property name="DynamicParameter" value="WI_ID=${item.externalId}" />
         <Property name="display_order_priority" value="5" />
          </Properties>
          <Descriptions default="" />
        </Action>
      </Actions>
    </ItemType>
5.Getting error,when I click task to perform dynpro abap screen.
6.WI_ID not been received.
Plz let me know the solution.
Thanks,

Hello,
I think you have to import the xml-file before clearing the cache again. Your new xml-file needs a higher priority then the default view.
You have just defined a new ItemType in your new xml-file. I am not sure, but I think that you will have to define in this file also a new view for this ItemType. Because otherwise it is not defined how this new ItemType should be shown.
Regards,
Iris

Configuring Webcenter Worklist with Oracle SOA Suite 10.1.3.4

Hi,
I have installed Oracle SOA Suite 10.1.3.4 on weblogic server 9.2. I want to configure Webcenter 11g worklist service with this SOA Server.
I would like to know if this is possible at all? Webcenter Suite 11g talks about configuring Webcenter worklist with SOA Suite 11g and I am not able to find any document
Thanks,
Vikas

Hi,
If you are trying to understand how to create a connection pool for a data source, then this document might be helpful
http://blogs.oracle.com/fusionmiddlewarereallife/soa_11g_bpel_composite_and_database_adapter.html

Configure Ultra 10 with D1000

Similar Messages

Maybe you are looking for