Configured local login on the console, but forgot to create a user...

I saved the config, restarted and now I can't log in. Is there any
way to undo this change? Should I just follow the normal password
reset procedure (press the mode button, backup config, etc) and then
create a login this way?I assume so, but I'm 50/50 on if I should just clear the whole thing out and start over since I'm not THAT far in.Thanks
Hi,
First check out that you are able access the router via telnet or console,I mean if your are getting the username prompt.If you are getting the username prompt then try the local username which you have configured.If that isn't working then try for password recovery to make this router as if like new one.
Check out the belowlinks on password recovery for different routers series
http://www.cisco.com/en/US/products/hw/routers/ps259/products_password_recovery09186a0080094675.shtml
http://www.cisco.com/en/US/products/hw/routers/ps274/products_password_recovery09186a0080094774.shtml
http://www.cisco.com/en/US/products/hw/routers/ps221/products_password_recovery09186a0080094773.shtml
and also check out the below link on how to configure local user database in routers
http://www.petri.co.il/csc_how_to_configure_local_username_database_cisco_ios.htm
Hope to help.
If helpful do rate the vlauable post.
Regards
Ganesh.H

Similar Messages

Hi, I just bought a new Macbook Pro 15" with SSD 256 Gb and its almost a brand new a while ago i was trying to connect to my home wireless network it said that your airport is not configured then I restarted the system but it didn't restart it shows the "

Hi,
I just bought a new Macbook Pro 15" with SSD 256 Gb and its almost a brand-new (the 4th time to use the device) a while ago i was trying to connect to my home wireless network it said that the connection is timed out so i clicked the airport sign on the top it said that your airport is not configured then I restarted the system but it didn't restarted it showed the grey screen with the apple logo and the spinning wheel for more than 10min so I tried the force shutdown by pressing the power button till it switched off I waited for 5min then pressed the power button to start or boot the system and again the grey screen with the apple logo and the spinning wheel, I waited for more than 20min nothing changed, any solution please?
Your help is really appreciated"

Thanks a lot i followed the instructions for safe mode (i found out that i was pressing the C button after restarting) i did whats written there but the repair couldn't be performed so in addition i needed to re-formate the HD so i erased the volume and then repaired the disk--> quite disk utilities --> start the installation from the installation DVD.
Thanks really appreciating your help

I am able to login to the Web, but when attempt to run the installer, it ask for a password and it does not work the password I used to login in the web.

I am new to Adobe Cloud, received the invitation from Adobe, create my account and I am able to login to the web. When Attempted to download Photoshop desktop, I was asked for Name and Password, the name was populated but I have to enter the password. I am using the password I entered at registration but it does not work and the Installer does not run.
I have a MacBook Pro with OS version 10.9.3.
Thanks,
Carlos

I figured out, the Installer need the username and password for the computer OS.

Configuration of LDAP through the Console

I am trying to create a customized object class to meet our specific needs on <b>LDAP - iplanet.</b> Everytime I try to add the customized object class to the users in an OU I get a message of Object class violation. I am not a programmer therefore I work out of the console.
I need help as I need to configure LDAP to receive HR data that is then going to be sychronized with our CUA master client for user creation.
Thanks in anticipation.
Pawan

Were you able to get the specific HR data sychronized with LDAP? We are working on this now and would like to know how you managed this task. THANKS

Airport utility is not working on Windows. I can configure Airport Expresses with the Macbook but multiple computers with Windows and the latest Airport Utility time out after trying to connect to the router for setup.

I have been trying to setup Airpot Expresses (both old and new models) for a while now with the Airpot Utility 5.6.1 for Windows without any luck. I have tried this on multiple windows machines, factory reseted the devices if I needed to, but I have not had any success since this software arrived. I see the routers on the Airport Utility UI, I click on it then try to connect to set it up. At this point, it gets stuck with a long progress bar trying to connect to the device without any success. I also have a Macbook Pro, and this device & software has had no trouble setting up the routers. The problem is, we are shipping these small routers out to customers who use Windows machines and it is vital that the user can modify the settings using Airpot Utility. I am at a loss for what to do and if we can't find any solutions, we are going to move on to a different company for the routers we ship out.

Thanks a lot i followed the instructions for safe mode (i found out that i was pressing the C button after restarting) i did whats written there but the repair couldn't be performed so in addition i needed to re-formate the HD so i erased the volume and then repaired the disk--> quite disk utilities --> start the installation from the installation DVD.
Thanks really appreciating your help

My network drives crashed and I was able to restore one with the exact same name and login. The second one I also created using the same name and login but it does not find the files when I click.

I get Connection failed when I click on the photo in IPhoto. This window keeps popping up and I have to force quit IPhoto.

iPhoto tracks referenced files using Aliases and this works just fine when the Library and the photos are on the same volume. However, Aliases won't survive being moved from one volume to another. This is why experienced users on here recommend against using Referenced Libraries in general, and in particular when the library and files are on different volumes.
Try repair the aliases with an app like FileBuddy If that fails then I'm afraid you'll need to do it manually for every photo in the Library, unfortunately.
Regards
TD

DAC - drops indexes in the task but does not create them back

DAC is dropping indexes for a task but not recreating them. The execution plan drop/create checkbox is checked and other tasks' index drop/create is working correctly. Index setup is checked for drop/create as well.
Is there somewhere within DAC that controls this function?
Any suggestions are appreciated.
Thanks.

You want a "Drop Box" style folder. You should be able to achieve this by creating a folder and giving it permissions similar to the "Drop Box" folder in your users Public Folder (i.e. write only permissions.)

HT2518 I've migrated from PC to IMAC, but it has created new users. I can't access these user accounts even though I've set up passwords for them as administrator. Can you assist?

I have transferred files from PC to IMac using Migration assistant. This has automatically set-up new users on the IMac and I can't access these. As administrator, I have set-up passwords for these new users, but when i try to acces these new users usung those passwords, the screen shakes as if the passwords are incorrect. Any suggestions?

fungec wrote:
I can see these in my user groups, and I can change the passwords on both as often as I like. But when I then try to logon, the screen just shakes and nothing happens.
I don't do Windoze, so haven't been able to test migrating from a PC.
There have been a few similar posts here. Are you trying to log on to the new user account(s) via Fast User Switching? If so, apparently that doesn't work. You need to turn that off (via System Preferences > Users & Groups > Login Options. Remove the check from the Show fast user switching .... box.
Then log out of all accounts, restart, select the new account from the login screen and you should be prompted to set the password.
I'm not sure a screenshot will help (and to be honest I'm not sure how to do screenshots on the IMac - I've been a PC man for over a decade!).
In most places, Shift+Cmd+3 will print the entire screen; Shift+Cmd+4 will produce a "target" you can drag over a portion of the screen.
EDIT: by "most places" I mean after you're logged-on, and OSX knows your preferences about how & where to put the screenshot. So it won't work on the login screen itself.
Message was edited by: Pondini

How to use the custom role which is created by user

Hi,
Can any one suggest how to use custom role created by developer in webcenter portal.
Thanks in Advance
Regards,
Ankur Bhatia

Hi Daniel,
Thanks for ur Reply,
But i am not able to understand where to write the above code.
Also Suppose if a role "GeneralAdmin" is activated for a user then how it behaves like a "GeneralAdmin".
Means where is the code was written so that it behave like GeneralAdmin after activation.
Thanks & Regards,
Ankur Bhatia
Edited by: 986921 on Mar 5, 2013 3:49 AM
Edited by: 986921 on Mar 5, 2013 3:49 AM

Failover to local login when TACACS is reachable but not authenticating

Hello, I'm confident I already know the answer to this question but I want to be sure.
I am moving a large number of Cisco devices to a new TACACS server, is there anything that can be done to allow local login if the new TACACS server is reachable but not authenticating for some reason? For example if the Cisco source IP is not built correctly into the server or the key is not configured properly on the device; in these situations the server is reachable but will not provide authentication.
I already have AAA authentication set similar to the following:
Router1(config)#aaa authentication login default group tacacs+ line
This will allow me to use line authentication if the tacacs server is not reachable but not if the server is reachable and not authenticating properly.
Any ideas on how/if I can failover to local login for the example situation I provided above?

Looks like NX-OS will not allow me to do this.
Nexus001(config)# aaa authentication login default local group TACACS
                                                                  ^
% Invalid command at '^' marker.
Nexus001(config)# aaa authentication login default local ?
<CR>
Nexus001(config)# aaa authentication login ?
ascii-authentication Enable ascii authentication
chap                  CHAP authentication for login
console               Configure console methods
default               Configure default methods
error-enable          Enable display of error message on login failures
mschap                MSCHAP authentication for login
mschapv2              MSCHAP V2 authentication for login
Nexus001(config)# aaa authentication login default ?
fallback Configure fallback behavior
group     Specify server groups
local     Use local username authentication
none      No authentication
Nexus001(config)# aaa authentication login default local ?
<CR>

[Solved] No sound on X, but it works on the console

I'm not sure what went wrong, so I'll tell the full story: I was struggling to get the Catalyst driver working. I have a Dell 5547, which has two graphics cards, an Intel HD 4400 and a Radeon R7 M260. I had installed the packages catalyst-hook and catalyst-utils-pxp from Vi0l0's repositories, but couldn't start X when I switched to the AMD card. Eventually, I downgraded to Xorg 1.14, also from Vi0l0's repositories, and now I was able to start X with both graphic cards. I'd read on The AMD/ATI Bar & Grill that downgrading to the Linux kernel 3.15.8 solved Daniel.White's problems, so I downloaded the corresponding linux and linux-headers packages from the Arch Rollback Machine. Later, I installed the last Linux kernel (version 3.16.1) and verified that I could still start X with both cards.
Before downgrading to Xorg 1.14, I installed Gnome 3 and everything worked great. I could listen to my music and watch videos on YouTube. Somewhere along the way, however, my sound stopped working. I'm using pulseaudio, and even after changing the settings using pavucontrol, I still can't get the audio to work -- on X. Sound works great on the console, but it refuses to work after I start X.
When I boot my computer and open an audio file with, say, mplayer, it complains that the "Audio device got stuck!"
pavucontrol reports that I have two built-in audio devices. The first one is off, and the second is set to "Analog Stereo Duplex". If I turn it off and then back on, mplayer stops complainning, but no sound comes out. On the "Output Devices" tab, pavucontrol now says that I have a "Dummy Output". It reverts back to normal once I reboot the machine.
Here's some info I think might be useful:
/etc/asound.conf:
# Use PulseAudio by default
pcm.!default {
type pulse
fallback "sysdefault"
hint {
show on
description "Default ALSA Output (currently PulseAudio Sound Server)"
ctl.!default {
type pulse
fallback "sysdefault"
Output of aplay -L:
null
Discard all samples (playback) or generate zero samples (capture)
pulse
PulseAudio Sound Server
default
Default ALSA Output (currently PulseAudio Sound Server)
/proc/asound/cards:
0 [HDMI ]: HDA-Intel - HDA Intel HDMI
HDA Intel HDMI at 0xb0c10000 irq 65
1 [PCH ]: HDA-Intel - HDA Intel PCH
HDA Intel PCH at 0xb0c14000 irq 62
Please let me know if you need more information. Thanks for reading!
Last edited by revberaldo (2014-08-23 15:03:17)

Hi emeres, thanks for the answer. I edited /etc/modprobe.d/50-alsa-base.conf as you suggested, then rebooted.
$ cat /etc/modprobe.d/50-alsa-base.conf
options snd-hda-intel index=1
options snd-hda-intel index=0
$ aplay -l
aplay: device_list:268: no soundcards found...
$ lspci -nn | grep -i audio
00:03.0 Audio device [0403]: Intel Corporation Haswell-ULT HD Audio Controller [8086:0a0c] (rev 0b)
00:1b.0 Audio device [0403]: Intel Corporation 8 Series HD Audio Controller [8086:9c20] (rev 04)
While mplayer is trying to play an MP3 file, I ran:
$ lspci -nn | grep -i audio
00:03.0 Audio device [0403]: Intel Corporation Haswell-ULT HD Audio Controller [8086:0a0c] (rev 0b)
00:1b.0 Audio device [0403]: Intel Corporation 8 Series HD Audio Controller [8086:9c20] (rev 04)
I edited 50-alsa-base.conf once again and rebooted the system.
$ cat /etc/modprobe.d/50-alsa-base.conf
options snd-hda-intel index=1,0
$ aplay -l
aplay: device_list:268: no soundcards found...
$ lspci -nn | grep -i audio
00:03.0 Audio device [0403]: Intel Corporation Haswell-ULT HD Audio Controller [8086:0a0c] (rev 0b)
00:1b.0 Audio device [0403]: Intel Corporation 8 Series HD Audio Controller [8086:9c20] (rev 04)
I even tried adding this to 50-alsa-base.conf:
options snd-hda-intel index=1 model=auto vid=8086 pid=0a0c
options snd-hda-intel index=0 model=auto vid=8086 pid=9c20
Then rebooted. Nothing changed. I swapped the indexes and that didn't work either.
Then I exited Gnome and ran aplay -l on tty1:
**** List of PLAYBACK Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC3234 Analog [ALC3234 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA Intel HDMI], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA Intel HDMI], device 7: HDMI 1 [HDMI 1]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA Intel HDMI], device 8: HDMI 2 [HDMI 2]
Subdevices: 1/1
Subdevice #0: subdevice #0
pgrep indicated that pulseaudio was indeed running, and I could play an MP3 with mplayer -ao pulse a.mp3. So, pulseaudio is running before X starts. I've checked my ~/.xinitrc and /etc/X11/xinit. Nothing there. That's crazy; what could be running that only affects X? Also, this problem is window-manager independent. It doesn't matter whether I'm running gnome3 or i3, I can't play audio inside X. If I go to tty3, for instance, sound works just fine.

Not able to login to weblogic console.

Hi,
I am trying to login to weblogic console, but it is failing with error message as follow:
*"Page not found*
The server has not found anything matching the Request-URI. "_
Previous it was fine i was able to login to the weblogic console without any issue, but suddenly this problem start apearing.
Please can somebody help me on this issue.
Thanks,
Manoj

Hi Ravi,
This is the config file sample. Please have a look to this.
<server>
<name>AdminServer</name>
<ssl>
<name>AdminServer</name>
<enabled>true</enabled>
<hostname-verification-ignored>true</hostname-verification-ignored>
<listen-port>9002</listen-port>
<login-timeout-millis>25000</login-timeout-millis>
<two-way-ssl-enabled>true</two-way-ssl-enabled>
</ssl>
<log>
<name>AdminServer</name>
<file-min-size>50000</file-min-size>
<rotate-log-on-startup>true</rotate-log-on-startup>
<log-file-severity>Info</log-file-severity>
<stdout-severity>Info</stdout-severity>
<memory-buffer-severity>Notice</memory-buffer-severity>
<log4j-logging-enabled>false</log4j-logging-enabled>
<redirect-stdout-to-server-log-enabled>true</redirect-stdout-to-server-log-enabled>
</log>
<stuck-thread-max-time>2400</stuck-thread-max-time>
<stuck-thread-timer-interval>180</stuck-thread-timer-interval>
<listen-port>9001</listen-port>
<web-server>
<name>AdminServer</name>
<frontend-https-port>443</frontend-https-port>
<auth-cookie-enabled>false</auth-cookie-enabled>
</web-server>
<listen-address>-------</listen-address>
<tunneling-enabled>true</tunneling-enabled>
<staging-directory-name>/apps2/bcawl10/applications_on</staging-directory-name>
<staging-mode>nostage</staging-mode>
<health-check-timeout-seconds>120</health-check-timeout-seconds>
<graceful-shutdown-timeout>60</graceful-shutdown-timeout>
<ignore-sessions-during-shutdown>true</ignore-sessions-during-shutdown>
<client-cert-proxy-enabled>true</client-cert-proxy-enabled>
<weblogic-plugin-enabled>true</weblogic-plugin-enabled>
</server>
I am accessing the console from a different windows machine while the admin server is configure on different unix box.
http://host_IP:9001/console is the url i am using to access the console.
As this is the production environment so we do not have permission or flexibility to create the new domains.
and for your previous post i did search for the files on the DemoIdentity.jks, DemoTrust.jks and wsrpKeystore.jks.
I am able to file the files at
/apps/bea/software/bea1001/wlserver_10.0/server/lib/DemoTrust.jks
/apps/bea/software/bea1001/wlserver_10.0/server/lib/DemoTrust.jks
/bea/software/bea1001/wlserver_10.0/samples/domains/portal/wsrpKeystore.jks
and i can see from the console that all the instance point to the same path mentioned above under KeyStore setting of weblogic console.
One more point i want to add is that console is accessible for few of the users what few of them are not able to access intermittently. So if you know then please could you put some input from the network prospective whether firewall setting can play role in in this or not.
Thanks,
Manoj Kumar

Separate User ID to configure OIF settings in EM console

Hi
We have OIF 11.1.1.7 installed and configured. We need to configure federation settings on EM console but we don't want to use weblogic account due to some restrictions by weblogic team. Does anyone know how to create separate userid in weblogic which can perform changes related to OIF only?
Thanks

I believe you can assign the user an OIF Admin or Operator rule per the below link
http://docs.oracle.com/cd/E28280_01/admin.1111/e13400/svradmin.htm#CACEBECI
Also take a look at the FederationAdmin role although from the doc it says "The FederationAdmin role is recognized only by WLST commands and other JMX MBean clients, not by Fusion Middleware Control. This means that users with the FederationAdmin role will only be able to configure Oracle Identity Federation through WLST or other JMX clients, not through Fusion Middleware Control"
Regards
Shiva

How do I get to the console of a VM using UCS Director?

Is there a way with UCS Director to present users of the system the console of the VM like when you launch the VSphere Client and bring up the console? I can see that users can RDP into a running machine or connect to a web interface but that appears to assume the machine is accessible.

I did that twice. Once, about an hour ago. And nothing changed. I did it again about twenty minutes ago, and still nothing. A few minutes ago I tried yet another force quit. And .... that seemed to do the trick. The offending email message is gone.
So my problem seems to be solved.
But the larger issue remains of a major bug in Mac OS, it seems. If a dialogue box is larger than the screen size, how is someone ever going to be able to deal with closing it or anything else? It would make sense to automatically allow the cursor to scroll down to the very bottom of any dialogue box, regardless of its size. After all, that's how windows work, right?
Crazy!

Can not login into the database 9i

I use WarehouseBuilder 9i's repository assistant to create new repository on a host.While the database is oracle 9i release 2 , the sysdba's name/password can't login into the database.But if the database is oracle 8.1.7 ,the sysdba's name/password can login.Why?
If the oracle 9i doesn't support WarehouseBuilder 9i ?

This is well known bug in OWH 9i.
The thing is:
1. Repository Assistant need to login under SYS and only SYS
2. SYS are allowed to login to Oracle 9i only AS SYSDBA
3. ... but Repository Assistant CANNOT correctly login by "SYS AS SYSDBA"
Solution:
1. Set Oracle 9i init parameter O7_DICTIONARY_ACCESSIBILITY=TRUE and restart database instance. This allow you to login as SYS (without SYSDBA) to Oracle 9i.

Configured local login on the console, but forgot to create a user...

Similar Messages

Maybe you are looking for