Configuring a 3845 that uses 2 BRI ...

Hi,
I would like to know where can I get help to write the configuration for a 3845 that uses 2BRI. I could not find any documentation to help me to get this information.
Thank you,
Cheers,
- sanjay -

Sanjay - Your requirement is still not clear, do you have a 3800 with Digital modems (MICA) and want async call to then over the 2 BRI interfaces? Is the BRI on a WIC or NM module?
Digital modem calls over WIC BRI is not supported. We will need a BRI NM (Network Module) card to support digital modems.
A sample configuration for the same (note this is on the 3600 platform but will remain the same)
http://www.cisco.com/en/US/tech/tk801/tk379/technologies_configuration_example09186a0080093c6e.shtml
Thanks, Mak

Similar Messages

Does Apple make/sell the new "Apple In-Ear Headphones with Remote and Mic" with a one sided configuration? So that a person that is deaf in one can hear both sides of a stereo recording? Also, since the "other" bud is not necessary/useful...it's removed.

Does Apple make/sell the new "Apple In-Ear Headphones with Remote and Mic" with a one sided configuration? So that a person that is deaf in one can hear both sides of a stereo recording? Also, since the "other" bud is not necessary/useful...it's removed.

As far as I know, Apple sells no such configuration. However, under Settings > General > Accessability, there is an option to play back audio in monoural mode, which would then play both halves of a stereo mix in each earbud.
Hope that helps.

How-do-i-configure-guest-wifi-access-using-2504-wlc-fortigate-utm-l3-device

Dear All
I have a 2504 Wireless Controller with multiple radios attached. I currently have a "private" WLAN configured (taking ip from windows server based DHCP of Range 192.1681.0/24 ) and working, but I need to add a Guest/Public WLAN which should take the IP from Other DHCP Configured on Fortigate UTM of range 172.16.0.0/24.
We have one SG300 switch in the office and the rest are basic switches.
Our firewall/router is a Fortigate UTM 240D
Find the attached network diagram for the issue.
Is there a SIMPLE way to enabling guest access that doesn't require VLANS (or are VLANS easier than I'm making them)?
Thanks.
- See more at: https://supportforums.cisco.com/discussion/12473186/how-do-i-configure-guest-wifi-access-using-2504-wlc-fortigate-utm-l3-device#sthash.aj1XcWI0.dpuf

Complete these steps in order to configure the devices for this network setup:
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-vlan/70937-guest-internal-wlan.html
Configure Dynamic Interfaces on the WLC for the Guest and Internal Users
Create WLANs for the Guest and Internal Users
Configure the Layer 2 Switch Port that Connects to the WLC as Trunk Port

How to configure Oracle 10g to use 4GB memory

I'm trying to configure Oracle 10g to use >4GB memory. Have configured server boot.ini with required flags (/3GB /PAE). Rebooted server then created standard database, then connected to db instance and changed oracle parameters DB_BLOCK_BUFFERS, USE_INDIRECT_DATA_BUFFERS as required. Restarted DB instance, DB fails to restarted with SGA memory error. According to oracle user docs the SGA is nolonger in effect due to previous settings. Can you provide example of SPFILE with parameters settings that do work and use >4GB memory. Current server has 8GB, 2 x Dual XEON core/processors (i.e. 8 processors)

The recommended /3GB switches in the boot.ini file can only be used with the following operating systems editions (KB article 291988):
Microsoft Windows 2000 Advanced Server
Microsoft Windows 2000 Data Center Server
Microsoft Windows Server 2003, Enterprise Edition
Microsoft Windows Server 2003, Data Center Edition
Microsoft Windows Small Business Server 2003
Important: Windows 2000 and 2003 Server Standard Editions DO NOT SUPPORT /3GB Switch.
So if your OS is listed above, then you cannot have a larger SGA.

Is there a way to configure Firefox so that certain cookies are kept even when the Tools/Options/Privacy is confirgured to removed all cookies when Firefox is closed? In other words, an "exception" list so that certain specified cookies would not be remo

For some websites that I visit every day, it is a pain to have to log in every time. (e.g., Zap2it, which provides TV listings in your local area). However, I like setting Tools/Options/Privacy to keep all cookies until I close Firefox. I would like to be able to configure Firefox so that all cookies would be removed EXCEPT those I specify. If I could do this, I would not have to log in every time.

You can't use [[Clear Recent History]] if you want to keep specific cookies by setting an exception.
"Clear Recent History" is all or nothing.
You can let the cookies expire if you close Firefox if you need to preserve specific cookies.
Tools > Options > Privacy > Cookies: "Keep until": "I close Firefox"
See also [[Cookies]]

[svn] 3519: Fix typo in error string for situations where there are advanced messaging configuration settings from LCDS used in the configuration files but no AdvancedMessagingSupport service .

Revision: 3519
Author: [email protected]
Date: 2008-10-08 04:17:40 -0700 (Wed, 08 Oct 2008)
Log Message:
Fix typo in error string for situations where there are advanced messaging configuration settings from LCDS used in the configuration files but no AdvancedMessagingSupport service. The error string said that there was no flex.messaging.services.AdvancedMessagingService registered but it is the flex.messaging.services.AdvancedMessagingSupport service that needs to be registered.
Add configuration test that starts the server with a destination that has the reliable property set which is an advanced messaging feature but there is no AdvancedMessagingSupport service registered.
Modified Paths:
blazeds/trunk/modules/common/src/flex/messaging/errors.properties
Added Paths:
blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/ReliableDestina tionWithNoAdvancedMessagingSupport/
blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/ReliableDestina tionWithNoAdvancedMessagingSupport/error.txt
blazeds/trunk/qa/apps/qa-regress/testsuites/config/tests/messagingService/ReliableDestina tionWithNoAdvancedMessagingSupport/services-config.xml

Hi,
Unfortunately I already tried all kinds of re-installs (the full list is in my original message). The only one remaining is the reinstall of Windows 8 itself, which I would really like to avoid.
What I find really strange is the time it takes for the above error message to appear. It's like one hour or even more (never measured exactly, I left the computer running).
What kind of a timeout is that? I would expect that, if ports are really used by some other application, I get the message in less than a minute (seconds, actually). To me this looks like the emulator itself for some reason believes there's a problem with
some port while in reality there isn't.
I'll eventually contact Microsoft Support, thanks for the suggestion.
▼
▲

Youtube and flash games work, but other sites that use flash don't work

Hi-
I'm currently using Firefox 18.0.2 on 2 different computers (Both Win7 64 bit), both with flash 11.6.602.168. Both have roughly the same programs installed and the same browser configuration. However, on one machine, flash works only on some sites. For instance, Youtube works perfectly, as do dedicated flash games. However, sites that use embedded flash applications fail to work. For instance, if I visit www.speedtest.net, where the test options normally appear is completely blank. Similarly, other video players fail. For example, videos in www.cbsnews.com play sound, but where the video should be is just white. I've tried completely uninstalling both firefox as well as flash, and installing previous versions, nothing has worked.

I guess it is a process of elimination, what is different ?
I would first of all check and experiment with Adobe FlashPlayer protected mode setting.
* http://kb.mozillazine.org/Flash#Flash_Player_11.3_Protected_Mode_-_Windows
Also have you any filtering, adblock or security related programs installed which may block video or scripts. With you-tube check is it actually using Flash player,and not trying to use any HTML5 options so check any options and cookies.

Problem configuring SOA suite to use OID for authentication

We are in the process of rebuilding our environment to use the full SOA suite with our OID server for authentication (was previously just BPEL using AD directly), and have encountered several problems (below). We have rebuilt the OID server, and reinstalled the SOA suite into a clean ORACLE_HOME to no avail.
We first rebuilt the OID server using the following steps (derived from Oracle® Internet Directory Administrator's Guide):
1)     Create the Import and Export profiles for AD synchronization. We did this using the Directory Integration and Provisioning Server Administration tool under “Active Directory Configuration”
2)     Modify the map file to specify the correct OU mappings between AD and OID.
3)     Update the profile with the new map file using “dipassistant.bat mp”
4)     Bootstrap the import profile using “dipassistant.bat bootstrap”
5)     Start a new instance of the Integration server (odisrv) running on config set 1 (the config set containing the Active Directory import/export profiles) using “oidctl”
6)     Set the Import profile to Enable. The OID server does not export changes to AD in our current configuration, so the Export profile is left on disable (and not bootstrapped)
At this point it appears that the AD synchronizes correctly into our new OID server.
Next we installed the SOA suite:
1)     We ran “irca.bat” on our database server to create the ORABPEL, ORAESB, and ORAWSM schemas and associated integration repository structure.
2)     After launching the SOA suite installer, we selected Advanced Install.
3)     On the next screen, we selected J2EE Server, Web Server, and SOA Suite.
4)     We then provided the credentials for our Oracle database, and the passwords for ORABPEL, ORAESB, and ORAWSM.
5)     We configured our new AS instance as an administration instance, but did not opt to use from a separate HTTP server, and did not make this instance part of an OAS cluster topology.
And finally, we configured our new SOA suite instance to use OID for authentication (using the instructions in Oracle® BPEL Process Manager Administrator's Guide section 2.1.3):
1)     Used the configure_oid.bat command to seed OID with required users only.
2)     Logged into the OracleAS Control Console
3)     Chose the oc4j_soa instance, then Administration->Security->Identity Management
4)     Configured the OID server using a non-ssl connection and the cn=orcladmin account.
5)     When prompted, chose to reconfigure all applications in the oc4j_soa instance to OID, but not to use SSO for any of them.
6)     Copied the contents of ORACLE_HOME\j2ee\home\config\jazn.xml to ORACLE_HOME\j2ee\oc4j_soa\config\jazn.xml
7)     Restarted the application server.
After this procedure, we encountered the following issues:
1)     The BPEL console appears to authenticate users correctly out of OID, but no users have access to the default domain, including bpeladmin and oc4jadmin. All users receive a similar access denied message when attempting to log into the BPEL Admin Console.
2)     We cannot upload a BPEL process to our new server via JDeveloper’s standard BPEL deployment mechanisms. The connection appears to be working properly and passes all tests, but on uploading a process we get a Java AccessDeniedException. ESB appears to be functioning properly, and accepts uploaded projects without issue.

Bassman,
We recently configured our SOA Suite to use OID and SSO. We had the same issues you are having, and we found the resolutions in a blog from Jaas Poot (http://blog.jpoot.com/category/oracle-appserver/oid-ldap/). For the BPEL domain access, this involved going to the data-sources.xml file and changing the database passwords from using ->pwForOrabpel for the orabpel schema and ->pwForOraesb for the oraesb schema to the real passwords; the blog explains more about this.
The blog also covers the JDeveloper deployment issue, and another issue we encountered, where we couldn't access the BPEL Admin console. All of these were resolved following the steps in the blog.
Hope this helps
Candace

Anyone succesfully configured a LinkSys WRT54G using a G5 tower for the IPh

Hi,
Anyone succesfully configured a LinkSys WRT54G using a G5 tower for the IPhone?
If so please, could you give megive me the router configurations?
As my wi-fi network won't even showup on IPhone.
Thanx
SvK

I have that same router and the iPhone found it with no prolblem..
I wish I could be mroe of a help try accessing your routers settings.

How to call Fortran .dll file that using other library files?

Hi,
I am trying to do some arkward tasks using LabView, and I am desperately need help....
A little bit background:
1. My co-worker has some code written in Fortran, where he called other libraries (many from CERNLAB or PAW). Those stuffs are pretty powerful in mathmatical calculation and simulations.
2. In some of my LabView code, I need to call his Fortran source code in order to do some complicated calculations. I have no capablility to translate his Fortran code to Labview (or is it even possible??), so we end up with trying to use "Call library function node" where I just provide input/outputs to communicate with his code. The idea sounds simple enough?
3. We complie the Fortran code into .dll, and then specifiy the dll in "Call library function node". The first try with a very simple Fortran code, something like c = a+b*a, was sucessful. The dll file and Call lib function worked good. It's sort of proved the concept.
4. Now I am trying more complicated Fortran code (say Test.dll), which calling other library (.lib files) that using typical "call xxx(a,b,c)" line, and my nightmare started.... It seems nothing was excuted when I call Test.dll in LabView.
Questions:
1. How do LabView know if the Test.dll code needs functions from other .lib files? Do I need to copy all the .lib files to a specific folder?
2. When I create .dll file, for LabView to be able to use it, are there any special requirement on the way the .dll is compiled?
3. Seems there is mismatch btw the data type in Fortran and LabView. For example, LabView's Signed 8-bit Integer seems different with a integer in Fortran. How can i know the correlation btw data type in different langurage, i.e. LabView vs Fortran?
4. Are there any good examples that I can take a look?
I would highly appreicate any suggestions/helps!
Rgds,
Harry

You are aware that Intel Visual Fortran is the successor to Compaq Visual Fortran (I think you made a mistype with the Virtual)? So an upgrade might be at its place.
Anyhow I'm really not familiar with Fortran at all, but lib files are usually compiled into an EXE or DLL and not loaded dynamically. 1)
So there should be no problem with locating those libs. What most likely is a problem are other DLL dependencies such as any Fortran Runtime library or possibly other third party DLLs the more advanced code in your DLL might be using.
Typically most compilers can be configured to link the runtime library code statically into the DLL, as altenbach reports for the Intel compiler, otherwise you must make sure to install the redistributable Fortran Runtime Library for your compiler. Besides that you must make sure to find out what other runtime dependencies your code might have and install them.
1) One exception I know of is LabWindows CVI which allows to also load lib files dynamically. This is supposedly a legacy feature from LabWindows for DOS, which allowed that feature to simulate dynamic module loading in order to swap modules at runtime to work around the 640k memory limitation of DOS.
Rolf Kalbermatter
CIT Engineering Netherlands
a division of Test & Measurement Solutions

Is there a function that uses Get_DAQ_Device_Info - device_type_code to get info

Is there a function that uses Get_DAQ_Device_Info - device_type_code to get info on the hardware characteristics such as a list of available gains or A/D converter resolution?

Duncan;
When calling Get_DAQ_Device_Info we get most of the information for our board. For example: the base address, calibration status, counter type, serial number, device type code, DMA and Interrupt levels, etc.
At this moment we do not have any function that will let us know the number of channels of a certain device and the configuration mode supported by the board.
However, you can use the Init_DA_Boards to retrieve what type of board is installed on the machine at a given time, and to have a look up table with the available gains for the possible boards that can be used on your application.
Hope this helps.
Filipe A.
Applications Engineer
National Instruments

Hidden Report Viewer Confiugration Error on aspx pages that use report viewer web control

I try to fix the problem. The error below is embedded on aspx pages that use report viewer web control. Please note that the div element is hidden, and the reportviewer is displaying correct contents.
Div element hidden on aspx page
<div id="ReportViewer1_HttpHandlerMissingErrorMessage" style="border-color:Red;border-width:2px;border-style:Solid;padding:10px;display:none;font-size:.85em;">
<h2>
Report Viewer Configuration Error
</h2><p>The Report Viewer Web Control HTTP Handler has not been registered in the application's web.config file. Add <add verb="*" path="Reserved.ReportViewerWebControl.axd" type = "Microsoft.Reporting.WebForms.HttpHandler, Microsoft.ReportViewer.WebForms, Version=10.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" /> to the system.web/httpHandlers section of the web.config file, or add <add name="ReportViewerWebControlHandler" preCondition="integratedMode" verb="*" path="Reserved.ReportViewerWebControl.axd" type="Microsoft.Reporting.WebForms.HttpHandler, Microsoft.ReportViewer.WebForms, Version=10.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" /> to the system.webServer/handlers section for Internet Information Services 7 or later.</p>
</div>
I tried adding the two elements to web.config, but to no avail.
Add below to system.web/httpHandlers
<add verb="*" path="Reserved.ReportViewerWebControl.axd" type = "Microsoft.Reporting.WebForms.HttpHandler, Microsoft.ReportViewer.WebForms, Version=10.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" />
or add below to system.webServer/handlers for Internet Information Services 7 or later.
<add name="ReportViewerWebControlHandler" preCondition="integratedMode" verb="*" path="Reserved.ReportViewerWebControl.axd" type="Microsoft.Reporting.WebForms.HttpHandler, Microsoft.ReportViewer.WebForms, Version=10.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" />
The required assemblies below are installed under C:\Windows\assembly folder. I have installed both Microsoft ReportViewer 2010 Redistributable, and 2008 SP1.
Microsoft.ReportViewer.WebForms, version 10
Microsoft.ReportViewer.Common, version 10
Below is the whole web.config:
<?xml version="1.0" encoding="utf-8"?>

<configuration>
<connectionStrings>
<add name="ApplicationServices" connectionString="data source=.\SQLEXPRESS;Integrated Security=SSPI;AttachDBFilename=|DataDirectory|\aspnetdb.mdf;User Instance=true" providerName="System.Data.SqlClient" />
</connectionStrings>
<appSettings>
<add key="car" value="myCar" />

</appSettings>
<system.web>
<httpHandlers>
<add verb = "*" path = "Reserved.ReportViewerWebControl.axd" type = "Microsoft.Reporting.WebForms.HttpHandler, Microsoft.ReportViewer.WebForms, Version=10.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" />

</httpHandlers>
<compilation debug="true" targetFramework="4.0">
<assemblies>
<add assembly="Microsoft.ReportViewer.WebForms, Version=10.0.0.0, Culture=neutral, PublicKeyToken=B03F5F7F11D50A3A" />
<add assembly="Microsoft.ReportViewer.Common, Version=10.0.0.0, Culture=neutral, PublicKeyToken=B03F5F7F11D50A3A" />
<add assembly="Microsoft.Build.Framework, Version=4.0.0.0, Culture=neutral, PublicKeyToken=B03F5F7F11D50A3A" />
<add assembly="System.Management, Version=4.0.0.0, Culture=neutral, PublicKeyToken=B03F5F7F11D50A3A" />
</assemblies>
<buildProviders>
<add extension=".rdlc" type="Microsoft.Reporting.RdlBuildProvider, Microsoft.ReportViewer.WebForms, Version=10.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" />
</buildProviders>
</compilation>
<authentication mode="Forms">
<forms loginUrl="~/Account/Login.aspx" timeout="2880" />
</authentication>
<membership>
<providers>
<clear />
<add name="AspNetSqlMembershipProvider" type="System.Web.Security.SqlMembershipProvider" connectionStringName="ApplicationServices" enablePasswordRetrieval="false" enablePasswordReset="true" requiresQuestionAndAnswer="false" requiresUniqueEmail="false" maxInvalidPasswordAttempts="5" minRequiredPasswordLength="6" minRequiredNonalphanumericCharacters="0" passwordAttemptWindow="10" applicationName="/" />
</providers>
</membership>
<profile>
<providers>
<clear />
<add name="AspNetSqlProfileProvider" type="System.Web.Profile.SqlProfileProvider" connectionStringName="ApplicationServices" applicationName="/" />
</providers>
</profile>
<roleManager enabled="false">
<providers>
<clear />
<add name="AspNetSqlRoleProvider" type="System.Web.Security.SqlRoleProvider" connectionStringName="ApplicationServices" applicationName="/" />
<add name="AspNetWindowsTokenRoleProvider" type="System.Web.Security.WindowsTokenRoleProvider" applicationName="/" />
</providers>
</roleManager>
<pages>
<controls>
<add tagPrefix="ajaxToolkit" assembly="AjaxControlToolkit" namespace="AjaxControlToolkit" />
</controls>
</pages>
</system.web>
<system.webServer>
<modules runAllManagedModulesForAllRequests="true" />
<validation validateIntegratedModeConfiguration="false" />
<handlers>
<add name="ReportViewerWebControlHandler" preCondition="integratedMode" verb="*" path="Reserved.ReportViewerWebControl.axd" type="Microsoft.Reporting.WebForms.HttpHandler, Microsoft.ReportViewer.WebForms, Version=10.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" />
</handlers>
<httpProtocol>
<customHeaders>
<remove name="X-Powered-By" />
</customHeaders>
</httpProtocol>
</system.webServer>
<system.serviceModel>
<bindings>
<basicHttpBinding>
<binding name="WebService1Soap" />
</basicHttpBinding>
</bindings>
<client>
<endpoint address="http://localhost:58269/WebService1.asmx" binding="basicHttpBinding"
bindingConfiguration="WebService1Soap" contract="ServiceReference1.WebService1Soap"
name="WebService1Soap" />
</client>
</system.serviceModel>
</configuration>
Any idea?
Update:
IIS is7.5, AppPool is Integrated.
I have tried below, none of them works:
1) Add it only to system.web\httpHanders. Changed AppPool to classic, still got hidden error.
2) Add it only to system.webServer\handlers. Integrated mode,still got hidden error.
3) Add both to both element. Integrated mode, still got hidden error.

Hi Kingofwebguru,
According to your description, when you use reportviewer control, you got the error message: The Report Viewer Web Control HTTP Handler has not been registered in the application's web.config file.
To troubleshoot the problem, please refer to the following steps:
Click Start, click Run, then type InetMgr.exe and click OK.
Click plus sign next to server name to expand it.
Click Application Pools in left pane.
In Application Pools list, click DefaultAppPool.
In the Actions pane, in Edit Application Pool section, click Edit Settings to check the Pipeline mode.
Configuration settings for the HTTP handlers are specified in the system.web/httpHandlers element and the system.webServer/handlers element. of your application Web.config file. The handler specified in system.web/httpHandler is used by Internet Information
Services (IIS) 6.0 or IIS 7.0 in Classic mode, whereas the handler specified in system.webServer/handlers is used by IIS 7.0 in Integrated mode. To use IIS 7.0 in Integrated mode, you must remove the HTTP handler in system.web/httpHandlers. Otherwise, IIS
will not run the application, but will display an error message instead.
For more information about Web.config Settings for ReportViewer, please refer to the following document:
http://msdn.microsoft.com/en-us/library/ms251661.aspx
If you have any more questions, please feel free to ask.
Thanks,
Wendy Fu
If you have any feedback on our support, please click
here.
Wendy Fu
TechNet Community Support

EPM System Configurator not prompting to use existing tables

Planning 11.1.1.3.
Oracle Database
Planning database configured using advanced jdbc URL with alternative servers.
Above is what we have installed and configurations settings we are using.
In the short of it, Our Oracle DBA changed the servicename for the Oracle database to go from <SERVICENAME> to <SERVICENAME.world>. Even going thru TOAD we have to use <SERVICENAME.world> now. When they did this our QA environment is now down and we have to reconfigure all of the databases to account for the new servicename.
We successfully reconfigured the SharedServices database just using the option to connect to an existing configured database and correcting the servicename, and it is working normally.
For all other products we will have to use the configure for first time option to be able to change the properties.
HOWEVER, when we use the 1st-time configuration for planning we are able to correct the properties for the connection and set the new servicename, but when we click next I would expect to be asked whether to reuse the existing tables or drop/recreate them, however, the screen just steps forward to the confirmation screen. In the configtool.log I have the following message:
(Oct 28, 2010, 11:18:12 AM), com.hyperion.planning.HspDBConfigurator, DEBUG, Planning tables exist already but will reuse it as upgrade now -- should be 9.3.X upgrade.
We want to be assured that performing the step without having the option to reuse tables will not wipe and recreate the planning system database.
So:
1. Why do we get this error when trying to reconfigure the planning database? Can we ignore it?
2. What steps do we have to take to ensure that the Servicename is updated in all configuration files, and database locations it is in?
3. Is there any viable way to do this outside of the configuration utility? (For example only editing files and registry)? If so what steps are required?
I would greatly appreciate it!
Robert

I am on 11.1.2.1. I was able to find the solution. I went to the C:\Users directory and copy the oracle.instances file from the original temp ID that had performed the installation onto the account that I want to use going forward. That resolved my issue and I am now able to start EPM configurator for update as well.

Configuring Cisco Router for use with Syslog Server

Configuring Cisco Router for use with Syslog Server:
Does anyone know of a good doc for this?
-Ashley

Start with that one: http://security-planet.de/wp-content/uploads/2008/12/logging-ios.pdf
And if you need more informations, just ask what you want to achieve.
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni

"dtutil", how to tell which configuration file for packages using after deployment?

Hello All,
Trying to achieve this feature,
Using DOS command to automatic my deployment process--glad I found dtutil. However, it doesnt give you any chance to identify which configuration file to be used by SSIS packages after deployment.
Deployment Method: file deployment
Configuration sued: XML file and SQL Table. IN XML file, it tells which DB connection for packages to look up the configuration table.
Who can share some thoughts on this?
Derek

It is NOT about sequence.
It is about how to point which configuration file to be used by deployed packages as during the "dtutil.exe"
deployment, you dont have chance to identify which physical location confg files to be used.
Derek
That you do only at the time of execution of packages. By default it uses configuration settings created at design time within the package. If you want to override it, you can use \Configfile switch of dtexec for that. You can also set explicit values for
properties using /SET switch
http://technet.microsoft.com/en-us/library/ms162810(v=sql.105).aspx
See this to understand how configs are applied in runtime
http://technet.microsoft.com/en-us/library/ms141682(v=sql.105).aspx
and this to understand behaviour difference in ssis 2008
http://technet.microsoft.com/en-us/library/bb500430(v=sql.105).aspx
Please Mark This As Answer if it helps to solve the issue Visakh ---------------------------- http://visakhm.blogspot.com/ https://www.facebook.com/VmBlogs

Configuring a 3845 that uses 2 BRI ...

Similar Messages

Maybe you are looking for