Configuring a AP 1552EU-A-K9 in layer 2 mode thru a WLC 5508 running 7.6.130.0

We have an outdoor AP that we want to bridge to another one that is also outside and connect to our WLC 5508. I see a lot of data for connecting via a layer 3 network, but nothing yet on a layer 2 network (which we run). Can anyone point me to some doc that would explain this?

We have an outdoor AP that we want to bridge to another one that is also outside and connect to our WLC 5508. I see a lot of data for connecting via a layer 3 network, but nothing yet on a layer 2 network (which we run). Can anyone point me to some doc that would explain this?

Similar Messages

  • Anchor mobility configuration getting lost in wlc 5508 ios code 7.4.100.0

    It is observed that in WLC 5508 , ios 7.4.100.0 ,  mobility anchor configuration on wlan  is getting lost .  we configure anchor ip address on  guest wlan > mobility anchor >  Switch IP Address (Anchor).
    We have configured the template on NCS 2.0 to push the anchor mobility ip address on all WLC
    Has anyone oberved this behavoiur. We have more than 100 WLC  , and  everyweek  mobility anchor configuration is lost on some WLC having code  7.4.100.0.

    I am having this exact same problem.  I am running 7.3 on 5508 WLC.   My remote site LAP's are using Flex (HREAP).  The initial access point that my laptop associates to connects with no problem, as soon as I wander out of range of the initial LAP and into the area of another access point, I lose data connectivity.   The was validated like the original post as I start a constant ping on the LAN and watch as the ping latency increases and then ping replies stop.  The only way to correct the problem is resetting of the wireless adapter on the laptop.  Side note my DroidX has no problem wandering from AP to AP.
    Laptop: Windows 7 32bit
    I then returned to my home site and test where I have a secondary controller and the LAP's are configured for local mode, no problems roaming from access point to access point.   Validated with constant ping test.  The pings drop for a second and re-
    continues as the laptop reconnects.
    **Edit: I am going to try the removing the DHCP Addr. Assignment required option, and report that back to the TAC engineer.
    Message was edited by: Michael Dunki-Jacobs
    **Edit Solved:***
    The problem is in deed solved by turning the "DHCP Address Required" but why?

  • Wlc 5508 : guest users to be configured only give access for internal SAP application

    Hi,
    I have one new requirement with one of the client.
    I have wlc 5508 with 6.0 firmware. I need to have one guest wlan which will have access only for internal SAP application.
    I have gone through cisco document for internet guest users , where web page will be redirected with user name and password once it is authenticated , we can access internet.
    Provided if we have access list configured in wlc ...  for internet access only /
    what about this mentioned scenario ?
    can anybody suggest on the same ?

    Hi Vinod,
    Go for the ACL on any Router or the switch.. i prefer not on the WLC..
    http://www.cisco.com/en/US/products/sw/secursw/ps1018/products_tech_note09186a00800a5b9a.shtml
    Here is the link as well to do it on the WLC
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00807810d1.shtml
    Lemme know if this answered ur question..
    Regards
    Surendra

  • How to change Layer Mode in Flash CS3?

    Hello,
    I would like to know how to change the layer mode to
    "multiply" with flash.
    I usually use photoshop CS2 to color my lineart. I set the
    top layer (the lines) to "multiply" to make the white transparent,
    and then apply color on layers underneath.
    I want to learn how to color my art on Flash, but I'm still a
    noob. I imported my bitmap lineart (inked by hand) and turned it
    into vectors (modify>bitmap>trace bitmap). Then I created a
    second layer underneath for the color, just like I would do in
    photoshop.
    But, the first layer's white areas are not transparent, so
    the color is not visible.
    So basically I just need to know how to change the top
    layer's mode to "multiply" so I can see through the white areas .
    Any help will be very appreciated.

    Nicochi,
    > So basically I just need to know how to change the
    > top layer's mode to "multiply" so I can see through
    > the white areas.
    Convert the top layer's artwork (raster or vector, doesn't
    matter) into
    a movie clip symbol -- select the artwork and go to Modify
    > Convert to
    Symbol -- and you'll be set. Once the symbol exists, you'll
    see mode
    choices in the Property inspector.
    David Stiller
    Co-author, Foundation Flash CS3 for Designers
    http://tinyurl.com/2k29mj
    "Luck is the residue of good design."

  • WLC 5508 Configuration

    Hi Team,
    Just i want to know below configuration are possible with WLC 5508.
    Can we define specific timing to keep an account enabled. For e.g. 9:00AM to 9:00 PM from <x> date to <y> date?
    -          Can we authenticate the “lobby admin” user through TACACS?
    -          Can we enforce password change for guest user when he login for the first time?
    Regards,
    Jana

    Can we define specific timing to keep an account enabled. For e.g. 9:00AM to 9:00 PM from date to date?
    ans:- Yes through if you integrate WLC through ISE then its possible:-
    Step 1 Choose Administration > Web Portal Management > Sponsor Group Policy.
    Step 2 Click the Action icon and choose an option.
    Step 3 Enter a name for the new policy.
    Step 4 Choose the identity group to be associated with the policy.
    Step 5 (Optional) Choose additional conditions by choosing one of these options:
    •Select Existing Condition from Library to choose an existing simple, compound, or time and date condition
    •Create New Condition to choose an attribute, operator, and value from the expression builder.
    Step 6 Choose the sponsor group to associate with this sponsor group policy.
    Step 7 Click Save.
    -          Can we authenticate the “lobby admin” user through TACACS?
    for this you need ACS as ISE dont suport TACACS right now.
    -          Can we enforce password change for guest user when he login for the first time?
    Yes through ISE its possible.

  • WLC 5508 Configuration Query

    Hi Team,
    Just i want to know below configuration are possible with WLC 5508.
    Can  we define specific timing to keep an account enabled. For e.g. 9:00AM to 9:00 PM  from <x> date to <y> date?
    -          Can  we authenticate the “lobby admin” user through TACACS?
    -          Can  we enforce password change for guest user when he login for the first  time?
    Regards,
    Jana

    You can do this with Cisco's ISE, but not all just using the WLC lobby admin feature
    Can  we define specific timing to keep an account enabled. For e.g. 9:00AM to 9:00 PM  from date to date?
    > No... the lobby admin can create only from the start of the guest credential creation and can set how many days, hours, minutes, seconds, until that credential expires.
    -          Can  we authenticate the “lobby admin” user through TACACS?
    > Yes
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a0080851f7c.shtml
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a0080871921.shtml
    -          Can  we enforce password change for guest user when he login for the first  time?
    > No you can't
    Thanks,
    Scott
    Help out other by using the rating system and marking answered questions as "Answered"

  • Inital configuration not saving in WLC 5508

    Hi Team,
    We having some issue with the wlc 5508 after configuring the initial setup it saved and ask for reboot but after it reboots again it is asking for the initial configuration again.
    It is repeating the same
    Please help on this issue.
    Regards,
    Arun

    i have the same problem but i reboot and save config the device after months  when i got the 0 access points supported on WLC after reboot  all the new  configuration  weren't  saved only the old configuration from 2 to 3 months old 
    and on AP i got the max no. of ap has reached 
    and those AP that dis-joint were joint to wlc a day before 
    the wlc supported 50 ap only 7 are joint and 11 were disjoint after 2 months 

  • Whether probably configure a phone Motorola Droid Ultra xt1080  in mode NV_ONLY?

    Whether probably configure a phone Motorola Droid Ultra xt1080  in mode NV_ONLY?

    Whether probably configure a phone Motorola Droid Ultra xt1080  in mode NV_ONLY?

  • How to configure two Cisco WLC-5508-50

    Hi everyone, last year we buy 1 wlc-5508-50 to use with cisco 1142 AP. This year we plan to add more APs and we just buy another WLC-5508-50 because it was cheaper than to buy 50 licences. We would like to know what is the best way to configure our second WLC so that we can distribute our 75 APs on each controller. Maybe someone can help us. Thanks!

    Hi Bernard,
    If you have WCS, you can use templates to synchronize your configurations on the WLCs.
    Another possibility is you can upload your current configuration from your production WLC, and then open up the configuration file and edit the IP addresses to give new addresses to the new WLC. You will also want to change the system name to be unique as well. You can then download this config onto the new WLC, as long as the IP addresses and system name are different it should not interfere with your current WLC.
    To have the WLCs operate together properly, you will want to make sure they are defined in a mobility group, see the following for instructions:
    http://www.cisco.com/en/US/docs/wireless/controller/7.0/configuration/guide/c70mobil.html
    -Patrick Croak
    Wireless TAC

  • How do I configure my Airport Extreme to work in Bridge Mode and provide specific IP addresses to clients

    My Airport Extreme is working with an Airport Express to wirelessly extend my wireless network.  Both Airports are configured in Bridge Mode per the instructions I found on Apple's support site.  I want to assign a specific DHCP address to a wireless camera that is in range of the Extreme, but I understand that the Extreme needs to be in DHCP Only mode to do this.  But if I change the mode to DHCP Only, the Extreme will lose contact with the Express.  How can I get both functions to work - wireless network extension and specific DHCP addresses?

    Then what device is providing DHCP? Only once device per subnet should be the DHCP server. One should be DHCP and NAT and the other in Bridge mode for most home setups. The unit with DHCP and NAT should be the one connected to your cable or DSL and the other set in Bridge mode only extends your network.
    On the wireless config page set whichever you're using to extend your network to "Extend a wireless network" and give it the details of the network to which you're attaching it.

  • Error message: Errors occurred during installation before ITunes could be configured. Your systerm has not been modified. To complete the installation, run the installer again.

    Trying to install iTunes and keep getting the following error message: "Errors occurred during installatino before iTunes could be configured. Your system has not been modified. To complete the installation, runthe installer again.
    This message appears everytime I try to install iTunes. Help!

    See Troubleshooting issues with iTunes for Windows updates.
    tt2

  • How do you make the layer mode take effect with no background in Elements?

    I have a picture of water splashing over a black background (like this:
    although this isn't the exact one). By turning the blending mode to "screen", I get the effect I want: it basically looks like the water is splashing over my image. The thing is, I need to save it as a .png file with part of the water "dripping" off the edge of my photo onto a transparent background (background must be transparent). The problem I have is as soon as the image hits the transparent background, the black comes back.
    I need a way to either remove all the black from the photo or, more ideally, find a way to make the image I see in "normal" blending mode the same as the image I see in "screen" mode. Any ideas? (I have Photoshop Elements 7.0, btw)
    Thanks!

    I don't understand how you're using "screen" blending mode on a single image, but is this the effect you're trying to get (I used a blue colour to show the transparent area at the bottom of the image):
    I used the free KillWhite plug-in (http://mikes3d.com/extra/scripting-plugins/killwhite/) with your image:
    Converted the image to RGB.  (Image...Mode...RGB Color)
    Duplicated the background layer (Ctrl+J).
    Inverted the colours on that duplicated layer (Ctrl+I), so that the black background becomes white.
    Used KillWhite to...well...kill the white on that layer.
    Inverted the colours again.
    Used Enhance...Lighting...Brightness/Contrast as well as Levels to darken the water splash.
    Added my flower image below the water splash layer and raised the bottom edge of the flower image to leave a transparent area.
    My layers wound up looking like this:
    Ken

  • CLI Configuration of WLC 5508 w 7.0.250.0

    Hi all.  Is there a way to get the configuration of a WLC through the CLI similar to that of what you'd get from Cisco IOS?  So far I've tried
    config paging disable
    show running-config
    and
    show run-config
    but the output doesn't look like that of what you could cut/paste like IOS. 
    Thanks for all input.

    Hi 
    This is the command you have to run
    (5508-1) >show run-config commands
    If you want to take the backup & restore that to a different WLC, then you have to follow the method given below.
    http://mrncciew.com/2013/01/25/backup-restore-wlc-configs/
    HTH
    Rasika
    *** Pls rate all useful responses ****

  • Configuring WLC 5508 and Iphone/blackberry to use certificates

    Hello, we would like to configure additional wlan for iphone/blackberry internet access. The goal is to have internal users (Active Directory users) using blackberry connecting to internal wireless network and update their mailboxes. We would like to avoid roaming charges for blackberry data traffic (email updates) but on the other hand we have to provide some way of authentication to blackberry/iphone so we know that only corporate blackberry/iphones can connect to internal network and update emails. It would be greatly appreciated if someone point me to configuration docs covering this issue or give me quick overview what has to be done to make this happening. We have radius server available if needed.
    Thanks so much.
    Appreciated.

    http://www.cisco.com/en/US/customer/products/ps6366/products_configuration_example09186a0080921f67.shtml
    With PEAP, you set up a Windows Server box as a root Certificate Authority and install the CA on all clients. Then, clients simply log on with their AD credentials.
    http://www.cisco.com/en/US/customer/tech/tk722/tk809/technologies_white_paper09186a008009256b.shtml
    EAP-TLS is much more secure because it requires a unique certificate generated by the CA installed on each client.

  • WLC 5508 HA SSO configuration failure

    I've just replaced an older 5508 with two new 5508 controllers that we wanted to run in redundancy mode.  I've followed the directions here: to configure my units.  at this time i have my management, and redundancy management IP addresses configured in the same vlan on both units, also the service port addresses are in the same vlan, and the virtual interface is the same on both units.  I setup the mirrored reference in the redundancy global configuration for redundancy mgmt IP and Peer redundancy mgmt IP on both units.  I have designated the primary and the secondary units.  after doing all of this i connected (with a patch cable) the RP ports on both units.  On either unit i enable the SSO option and get the following message:
    "Please configure Redundancy Management VLAN before enabling redundancy"
    Clicking OK on this disables the option and returns me to the redundancy global configuration page.  I have searched all over and have been unable to find a working resolution for this problem.  I'm not finding much reference to this at all actually.
    Thanks in advance.
    Beer

    I read that but i'm confused as to what it actually means.  I have no redundancy VLAN unless it refers to the network created by the two service port IP addresses.  the devices are setup back to back, and only connect through the RP ports on each device.  here are the steps i took in setting this up.  before taking these steps the primary unit was configured and fully operational and the secondary only had a management ip address on it.  (I expected the secondary to sync it's configuration from the primary so did not set anything up further than needed for connectivity.)
    Log into both controllers using their web interfaces
    Navigate Controller > Interfaces
    Set the Management IP addressBoth units must have the management addresses within the same VLAN
    Set the redundancy-management IP addressBoth units must have the redundancy management address  in the same VLAN as the management interfaces
    Set the Service-port Ip addressBoth units should be setup so their service ports are in the same VLAN
    Set the virtual port IP addressThis should be the same on both units.
    Navigate to Controller > redundancy > Global configuration
    Verify the redundancy mgmt IP is prepopulated with the IP address from the redundancy-Management interface
    Set the Peer redundancy mgmt IPThis is the redundancy management IP Address form the opposing WLC
    On the primary unit set the redundant unit to Primary
    On the secondary unit set the redundant unit to secondary
    Click apply on both units
    Verify physical connection is in place between the RP ports on both WLC units
    Set the SSO option to Enable and click Apply on both units, starting with the primary unitThis will trigger a reboot on each unit after clicking apply.  The redundancy configuration setup will cause both units to reboot 2-3 times as the configuration is synced from the primary unit to the secondary unit
    Did I somehow miss a critical step in this process?

Maybe you are looking for