Configuring a Monitoring Port

What is the correct configuration on the switch side (Nexus 5K) when configuring a monitoring port from the FIs?

You don't have to...Just put a 1GbE SFP in the FI, plug your Laptop into it and start a monitor session.
Regards,
Daniel

Similar Messages

Cisco Network Analysis Module (NAM) data monitoring port

Hi, need some insight on this please. Your comments are appreciated.
My Cisco NAM 2220 comes with 10G data monitoring port, can I configure an IP address on this port for data monitoring?
or this data port can only support monitirong span, rspan, ersapn, vacl only (not for IP routing) and needs to be functioning in a promiscuous mode only?
Many thanks
Joe

Hi Lamine,
The official installation guides for NAM software can be found here:
http://www.cisco.com/en/US/products/sw/cscowork/ps5401/prod_installation_guides_list.html
Is this what you are looking for?
Cheers,
Shane

Is there a way to Configure "Silent Monitoring" in CUCM with the following conditions: ?

Is there a way to Configure "Silent Monitoring" in CUCM with the following conditions: ?
-no UCCX platform
-cisco phone is CP-6941.
I have read some cisco docs pertaining to Barge and cBarge, however i see that as one-to-one arrangement.
Is there a way to configure in cucm, something like an ad-hoc conference wherein the Observer will
just call the extension number to be observed?
or something like "service observed" feature in Avaya wherein the Observer will dial a particular
passcode followed by the extension # of the agent, then he is able to observe the on-going call.

You can do continous recording using SPAN ports or DMS with 3rd party products like Verint Impact 360.
not sure about the legalities around that though.
=============================
Please remember to rate useful posts, by clicking on the stars below.
=============================

Catalyst 2950 Series - Monitoring Port

Do the catalyst 2950 series have a port that can be used to connect a device that is designed to monitor all traffic on the switch - we are looking to install Webspy to track network & internet usage. The Sentinal product would best be connected to the switch where it can record all traffic - it needs a monitor port or some such equivalent.

Hi,
The 2950 does indeed support that - the functionality is called Switch Port Analyzer (SPAN). The following link has details on how to configure it:
http://www.cisco.com/en/US/products/hw/switches/ps628/products_configuration_guide_chapter09186a00800d84c5.html
Hope that helps - pls rate the post if it does.
Paresh

Can't configure both WAN ports on 1811 with SDM

Hi,
We recently procured an 1811 router to replace a SOHO linksys at a store we service. We needed redundant WAN interfaces to use the DSL as a backup to the main cable connection, and a Linksys RV082, while doing the job when it actually worked, died repeatedly. We decided after looking at the 1811's feature set to just get the Cisco and be done with it and not monkey with SOHO gear anymore.
Where I'm having difficulty is SDM won't let me configure both WAN interfaces from the GUI, it only allows me to configure one. I have it configured, and the router is working nicely in the test lab but I need to get that other interface configured and failover enabled before I can put this thing into production.
What am I doing wrong? Do I need to suck it up and learn IOS?
Thanks,
Todd Phipps
Certco, Inc.

I ended up figuring out the IOS commands to enable one fastethernet port as a primary and the other one as a backup (running both cable and DSL for redundancy; it's a grocery store that runs electronic transactions over IP so 100% availability is a must).
The trouble I was running into in SDM is that while it would allow me to configure one WAN port through the GUI, the config options for the second one were grayed out. Now that both are configured through IOS the edit buttons for both WAN interfaces appear normally in SDM. It's almost as if Cisco didn't want users to be able to configure both interfaces graphically for initial setup.
Now just to test it at the site before the store opens to see if the failover works...
Todd

Can you configure a static port to use with certsrv.msc?

I am trying to use certsrv.msc to connect from my workstation to the CA for administration purposes. Workstation is Win7, CA is 2008 R2 Enterprise running Enterprise Subordinate on a dedicated box.
I configured a static DCOM port for certsvc by following this article, including bouncing the service and also rebooting the CA box:
http://social.technet.microsoft.com/wiki/contents/articles/1559.how-to-configure-a-static-dcom-port-for-ad-cs.aspx
The static port was opened in the firewall from my workstation to the CA. We also found that TCP 445 was required, so that has been opened as well, port 135 & other ports normally needed for autoenrollment should be open. Sniffing the firewall
showed that a random high numbered port that is not the static dcom port is being attempted - this is the only port showing dropped packets & no traffic on the static port.
I am wondering if there is a way to configure a static port for this high-level random port to use with certsrv.msc as I was able to do with the certsvc dcom port? I am trying to avoid having tens of thousands of network ports wide open going to my
CA... Thanks in advance!

Hi Steve,
I am sorry that I wasn’t able to find references about restricting certificate services only use one port in the random port range.
However, we can configure RPC dynamic ports allocation to restrict port range. In the meantime, we should keep at least 100 ports open to keep necessary system services running.
More information for you:
How to configure RPC dynamic port allocation to work with firewalls
http://support.microsoft.com/kb/154596/en-us
Service overview and network port requirements for Windows
http://support.microsoft.com/kb/832017/en-au
Firewall Rules for Active Directory Certificate Services
http://blogs.technet.com/b/pki/archive/2010/06/25/firewall-roles-for-active-directory-certificate-services.aspx
Best Regards,
Amy Wang

PO 7.4 - Testing payload from "Configuration and Monitoring Home"

Hello,
I am working on PO 7.4. I want to test a payload from "Configuration and Monitoring Home". However, in the "Testing" tab, the option to test the payload is not available. Is this option not available in PO 7.4? Only cache connectivity test exists. I have attached a screenshot for reference.
Regards,
Mateen

Go to Monitoring --> Adapter Engine
                                   --> Message Monitor
                                              --> Select the message
                                                        --> open message ( Make sure pop-ups are allowed).
You can also Resend & test the message/payload.
Regards,
Dipen.

How to configure the eth1 port of NIcRIO 9024 to another IP address and subnet mask

Hi ,
I am using cRIO 9024 and am planning to configure it to be an MMS server that interacts with a client which is in another network with different IP and subnetmask. I want to run the server VIs from the host computer via the eth0 port and want to communicate the MMS messages through the eth1 port. the eth0 port is configured as a static IP as shown in the screenshot attached and would like to assign a separate IP and subnet mask to the other port . But when I try to save the configuration I get the error "Could not save your changes tot he target.The subnet mask for eth1 is invalid" .
I have already directly cross connected the Crio and have disabled the firewalls and still am not able to configure it.
1) is it possible to configure the ethernet ports to have separate IPs corresponding to different networks and thus the subnet masks?
2) If its possible then what is the mistake i am doing while configuring it ?
I would be extremaly grateful to have a reply on this as its pretty desperate to spend a lot of time just to set up the IP configurations..!!!!!
Regards
Abhinav

Dear Abhinav,
I'm sorry but what you are tryining to do is not suported by the Second Ethrnet Port on any cRIO and so you getting this error meeage.
Here a abstract out ouf the KnowledgeBase How do I Configure the Dual Ethernet Ports on Real-Time Controllers?:
Ethernet port 2 is currently not supported to communicate outside its own subnet. There is no capability of configuring the Default Gateway for Ethernet port 2 and therefore cannot connect to a large isolated intranet. However, there appears to be a common misconception that this port can only be used for communication between NI products: this is not the case, though any communication through the secondary port must be within the same subnet.
Kind Regards,
SG3 | Applications Engineering | National Instruments | NIG |

PLEASE I JUST NEED TO CONFIGURE TO OPEN PORT 22

Very sorry for the redundant post. I am in a desperate situation where the RAID on my NAS has been lost and I need remote tech analysis ASAP.
Can anyone out there please help me configure so that Port 22 is open???
I have a Thecus N5200 and an brand new Airport Extreme.

bevatore wrote:
Do I use the same Private IP address or do I use the Remote Management IP from Sharing in the computer's Preferences.
The "Remote Management" IP address should be the LAN IP address that your router gives to your computer. That should be the same as a "private IP address".
Also, do I need to to configure a DHCP Reservation for this IP in AirPort Utility?
If you don't do that, the IP address of your computer could change between restarts, causing the mapping to fail. If you only have one wireless client, that's probably unlikely. However, reserving an IP address will guarantee that your computer always has the same IP address.

Change/Configure Host and Port for the Web Service Proxy with Server

Hi,
Is there a way to configure Host and Port in generated proxy for Web service depending upon server. (ADF 11g)
Scenario:
We are consuming Credit Card web service from a service provider and have different Host and Port details for development, QA and Prod.
So we created proxy classes using wsdl for development and things work fine, but when deploying code to QA or Prod we need to change the Host
and Port details.
Is their a way we could user variable's for Host and Port which looks to some configuration file to evaluate their values
based on server.
I am a bit new to this web service .. will appreciate if someone could provide an example.
Thanks.

Are you using Web Service Proxy or Web Service Data Control?
If you are using Web Service Proxy. Right click on your Proxy --> Properties --> Port Endpoints. Here you can change the IP & Port details for each port.
Venkat

Cisco desktop administrator Services Configuration Multiline, Monitoring & Recording Remove VoIP/Recording & Playback Services

I remove default VOIP Monitor Service in "Cisco desktop administrator>Services Configuration > Multiline, Monitoring & Recording >Remove VoIP/Recording & Playback Services". Now I can't choose in "Services Configuration > Multiline, Monitoring & Recording > VoIP Monitoring Device" Default VOIP Monitor Service. How can I return choice my VOIP Monitor Service(IP UCCX)?

Hi Kalitamih,
This can be regenerated by the Cisco Desktop VOIP Monitor Service.
Please stop the service and start it (do not restart). Let me know how it goes and if it resolves the problem.
Regards,
Arundeep

Configure external monitor to be --left-of laptop screen (nouveau)

Hi,
I have problem configuring external monitor to work like nvidia's 'twinView'.
Having no xorg.conf my external monitor is configured just to clone image displayed on latop screen. I can setup correct resolution in my DE (I'm using XFCE), but what confuses me is how to configure external monitor to work as separate screen (not to present cloned image).
This my my output from xrandr:
[kuba@t61:~]$ xrandr
Screen 0: minimum 320 x 200, current 3120 x 1050, maximum 8192 x 8192
LVDS-1 connected 1440x900+1680+0 (normal left inverted right x axis y axis) 304mm x 190mm
1440x900 60.13*+ 50.00
1152x864 59.96
1024x768 59.92
800x600 59.86
640x480 59.38
720x400 59.55
640x400 59.95
640x350 59.77
VGA-1 connected 1680x1050+0+0 (normal left inverted right x axis y axis) 474mm x 296mm
1680x1050 59.95*+
1280x1024 75.02 60.02
1152x864 75.00
1024x768 75.08 60.00
800x600 75.00 60.32
640x480 75.00 60.00
720x400 70.08
DVI-D-1 disconnected (normal left inverted right x axis y axis)
Following wiki instructions (http://nouveau.freedesktop.org/wiki/Randr12/) this commad helps me to setup what I want:
xrandr --output VGA-1 --left-of LVDS-1
and I want to persist such configuration.
I tried to configure it in /etc/X11/xorg.conf (there was no such file)
[kuba@t61:~]$ cat /etc/X11/xorg.conf.bak
# the right one
Section "Monitor"
Identifier "LVDS-1"
Option "PreferredMode" "1440x900_60.13"
EndSection
# the left one
Section "Monitor"
Identifier "VGA-1"
Option "PreferredMode" "1680x1050_59.95"
Option "LeftOf" "LVDS-1"
EndSection
Section "Device"
Identifier "nvidia card"
Driver "nouveau"
#Option "Monitor-DVI-I-1" "NEC"
#Option "Monitor-DVI-I-2" "FUS"
EndSection
Section "Screen"
Identifier "screen0"
Monitor "VGA-1"
DefaultDepth 24
SubSection "Display"
Depth 24
#Virtual 2560 2048
EndSubSection
Device "nvidia card"
EndSection
Section "ServerLayout"
Identifier "layout0"
Screen "screen0"
But it seems like still there is something wrong as every time I run X I have cloned output on both screens.
Any ideas?
Last edited by jakub (2014-11-16 12:05:19)

jakub wrote: Option "LeftOf" "LVDS-1"
Should that not be "left-of"?

Steps to configure Solution Monitoring for Satellite Syst.

Hi Experts,
I am using my friend's ID for posting my query.
I need to configure Solution monitoring of different Satellite Systems in our Solution Manager server.
Could you please give me the steps for configuring the same.
Please help.
Thanks in advance,
Sandeep.

Sandeep,
You will get good documentation & tutor files from https://websmp206.sap-ag.de/ -> Knowledge Exchange,Solution Manager -> Solution Manager 4.0.
Hope this will help.If not please let me know.
Regards,
Cherry

Can't configure tacacs-server port

We're unable to configure a specific port, which is required for our customer for the tacacs-server. One of the devices is a 7604 router running this image -
c7600rsp72043-adventerprisek9-mz.122-33.SRD6.bin. The other device is a 2960 switch with the following image - c2960-lanbasek9-mz.122-35.SE5.bin.
We don't get the option to add a port after the tacacs-server host x.x.x.x command.
Any ideas would be greatly appreciated!
Regards..

Hi
Please go through this link, this will be helpful regarding TCSACS Authentication and Fortigate configuration:
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.2/user/guide/acsuserguide.html

Configuring Simple monitoring application

Hi
We have a requirement to to create the following
Configure simple monitoring application that will check for the number of concurrent BOBJ sessions used
send out alerts to team and manager when reaching a threshold.
Also if threshold is reached, we should also be restarting one or more CMS in the cluster to get rid of the inactive sessions.
The same application should also have the ability to send out the usage summary by day, week and month as well.
Please assist if there is any possibility of configuring the following in BusinessObjects applications
Thanks & Regards,

Have you got any chance to check here?
SAP BusinessObjects 4.0 Monitoring Configuration - Part(1)
SAP BusinessObjects 4.0 Monitoring Configuration - Part(2)
SAP BusinessObjects 4.0 Monitoring Configuration - Part(3)
You can get most of questions answered here

Configuring a Monitoring Port

Similar Messages

Maybe you are looking for