Configuring AAA network client on ACS v5.1 using the same RADIUS atributes from ACS v3.3

Hello,
I was wondering if i should use the same RADIUS VSA attribute on ACS v5.1 to authenticate AAA clients as those i was using on my old     ACS v3.3 server.
Exemple : under ACS v3.3 i was using RADIUS (Cisco Aironet) attribute to authenticate AP & WLC, should i do the same under ACS v5.1 ?
Best regards.

Hello,
When defining AAA client on the new ACS 5.x server you just select TACACS+ or RADIUS. We no longer define the RADIUS "vendor"/"VSA" when creating the AAA Client entry. All AAA client would be defined as RADIUS or TACACS+ only.
If you were using specific VSA Attributes then you need to send those attributes back configuring Authorization Profiles on the ACS 5.x. You will find the specific VSA attributes there. Refer to the following screenshots:
And here are the available attributes for the ACS for RADIUS Aironet:

Similar Messages

  • Configuring AAA network client on ACS v5.1 using the same atributes from AC

    Hello,
    Actualy i'm new to use ACS v5.1 and i wanted to do the same AAA client configuration as it was configured on my old ACS V3.3 server.
    My old ACS v3.3 AAA clients type are WLC, LAP and Autonomous AP (using RADIUS (Cisco Aironet)) authentication protocol, PIX & a Router (using TACACS+ (Cisco IOS)) authentication protocol.
    I'm using PEAP_MS-CHAP v2 as a RADIUS authentication method.
    Can any one guide me to accomplish this configuration please ?.
    Best regards.
    Posted by WebUser Mourad Lafjer

    Hello,
    When defining AAA client on the new ACS 5.x server you just select TACACS+ or RADIUS. We no longer define the RADIUS "vendor"/"VSA" when creating the AAA Client entry. All AAA client would be defined as RADIUS or TACACS+ only.
    If you were using specific VSA Attributes then you need to send those attributes back configuring Authorization Profiles on the ACS 5.x. You will find the specific VSA attributes there. Refer to the following screenshots:
    And here are the available attributes for the ACS for RADIUS Aironet:

  • Can v use the same Client for setting the ALE ??

    Can i use the same client like 080 for my ALE configuaration ?

    Configuring is a Cross-Client(Client Independent) activity.
    Check whether you have necessary access/authorizations to Configure.
    This should be always done in Development client.
    Hope this helps.
    Regards
    Vinayak

  • Have an airplay enabled AV Receiver - how do i set up Airplay    I have a Yamaha RX-V673 which is Airplay enabled, but i can't get Airplay to work either on my Mac book or my iphone. The receiver is connected to my network and i can control it using the

    have an airplay enabled AV Receiver - how do i set up Airplay
    I have a Yamaha RX-V673 which is Airplay enabled, but i can't get Airplay to work either on my Mac book or my iphone. The receiver is connected to my network and i can control it using the iphone App and via the web browser option.
    Do I need Apple TV or to change some settings somewhere?
    Any help would be greatly appreciated

    You are making some progress with setup of wireless network. Apparently there is reliability problem with the wireless connection. Perhaps you want to refer to following Apple support documents and start tweaking parameters in the router to improve the reliability. I used to have third-party routers such as Belkin and Netgear but switched to Apple Airport routers (Time Capsule then Airport Extreme for now) because of incompatibility issues whenever Apple upgrade Mac OS X. But since Apple develops Airplay protocol as alternative to Bluetooth for wireless audio/video streaming (with much better bandwidth) and must be deployed in any wireless network, there is no reason third-party routers not working for Airplay protocol.
    About AirPlay Mirroring in OS X Mountain Lion:
    http://support.apple.com/kb/HT5404
    iOS: Recommended settings for Wi-Fi routers and access points:
    http://support.apple.com/kb/HT4199
    Troubleshooting AirPlay and AirPlay Mirroring:
    http://support.apple.com/kb/TS4215
    Good luck in setting up 802.11 wirelesss network.

  • I have a wireless network at home. I run my iphone and ipad on it with no problems. Just purchased a MacBook Pro, and now my wi-fi keeps disconnecting and i get an error message saying another device is using the same IP address. What does all this mean?

    I have a wireless network at home. I run my iphone and ipad on it with no problems. Just purchased a MacBook Pro, and now my wi-fi keeps disconnecting and i get an error message saying another device is using the same IP address. What does all this mean?

    Hello AKCamus
    To give you some ideas of what to do next, I have provided a few articles that will give some troubleshooting Wi-Fi connections and recommended Wi-Fi settings.
    iOS and OS X: Recommended settings for Wi-Fi routers and access points
    http://support.apple.com/kb/HT4199
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/ts1398
    Troubleshooting Wi-Fi issues in OS X Lion and Mac OS X v10.6
    http://support.apple.com/kb/HT4628
    Thanks for using Apple Support Communities.
    Regards,
    -Norm G.

  • Two Iphones on the same WiFi network, using the same Apple ID receive calls meant for only one of the phones.

    My husband and I each have an IPhone 6.  We are using the same WiFi network and the same Apple ID, the phone numbers are different.  When we are at home, both phone receive calls meant for one of the phones.  Call can be answered from either phone.  Is this a new feature and How can I turn it off?

    go into settings then FaceTime then turn off iPhone cellular calls

  • I am trying to set up home sharing between my iphone 4s and mac which is running itunes 11. Both are connected to my home wifi network and using the same apple id but on the iphone app it says 'Turn on Home sharing in iTunes on your mac using account ***

    I am trying to set up home sharing between my iphone 4s and mac which is running itunes 11. Both are connected to my home wifi network and using the same apple id but on the iphone app it says 'Turn on Home sharing in iTunes on your computer or apple tv using account ***
    Does anybody have suggestions as to why this is the case?

    Understanding Home Sharing - Support - Apple
    Hope this helps.

  • How can I get Firefox to run on a network with multiple users logging on with the same user name and password?

    I am trying to get Firefox running on a large network where I have multiple users that log on with the same user name and password. The problem is that when another user logs on to another computer the message comes up that their is already an instance of firefox running on that computer even though there really isn't. Only one instance can be run on the network at one time. I believe it is because firefox stores a shared profile as it thinks it is actually the same user even though it is being run on another computer. I repeat that each user that logs on uses the same user name and password but on different computers.

    I am trying to get Firefox running on a large network where I have multiple users that log on with the same user name and password. The problem is that when another user logs on to another computer the message comes up that their is already an instance of firefox running on that computer even though there really isn't. Only one instance can be run on the network at one time. I believe it is because firefox stores a shared profile as it thinks it is actually the same user even though it is being run on another computer. I repeat that each user that logs on uses the same user name and password but on different computers.

  • Using the same library with multiple computers over a network Use Aperture

    Hi Everyone. I am researching some cataloguing/editing programs to recommend one to my boss, and I was wondering if it was possible to use the same library between multiple computers on a network. Does anyone know if this is possible? This may be what makes or breaks the decision on whether or not to go with Aperture as we need a program that can access a large database of photos on multiple computers.
    Thank you.

    Welcome to the forum.
    You can do it, but...
    It's not supported by Apple.
    Performance won't be great unless you're running a really fast network.
    If more than one person tries to access the Library at one time you're likely to end up with a corrupted database, and there's no code in Aperture to limit access to one person at a time.
    The Library must be stored on an HFS+ volume - don't even try putting it on a FAT32-formatted drive.
    If you want 'proper' multi-concurrent-user network-enabled cataloguing software you're looking into a whole different level of investment than the low price of Aperture - think more in terms of thousands or even tens of thousands of dollars.
    Ian

  • Configuring SMTP Namespace Sharing between two Exchange Forests on the same LAN

    Hi guys, really hoping that someone can help me with configuring SMTP Namespace Sharing between two Exchange Forests on the same LAN.
    Basically, I have created a new forest and installed a new exchange organisation in this forest.  Both forests are located on the same IP subnet and a two way trust has been created between the forests.  Federated sharing has also been configured. 
    I can use ADMT to migrate the user and computer accounts to the new forest and also migrate test mailboxes over.  Ideally, I want to be able to do the mailbox migrations in stages so will need to be able to have mail flowing between the two forests. 
    I have read over the following article (http://ibrahimnore.wordpress.com/2012/09/06/configuring-smtp-namespace-sharing-between-two-exchange-forests-part-2/)
    which is good but it's demonstrating over the internet, can anybody advise how this can be achieved on the local LAN? 
    Any help greatly appreciated :-)

    Hi Gilliano,
    Thanks for correct link. I must say this is a very good article indeed, I read the entire article and if you go to the 3rd part of this article, please note the text "DOMAINC.COM is configured as Internal Relay Accepted Domain on both the domains"
    This is exactly what I asked you to check. Personally, I understand the method described in this article will work but its very complex to manage and administer, while the easiest option is to configure internal relay at the first place and no need to make
    so many DNS changes and customizations to your environment.
    The solution really depends on what your requirement is - Since you mentioned that you are migrating stuff over from source to destination - I feel this article is too complex for your situation and not really worth (for your requirement). The setup described
    in the article is an excellent choice if you are planning to keep both forests alive for longer duration due to several reasons like compliance or company mergers and so on...
    please let me know if my explanation is not clear enough.. we can even even have a one-on-one email conversation too!
    All the best!
    Please mark as helpful if you find my contribution useful or as an answer if it does answer your question. Regards, Siva

  • Can you share photos between machines that use the same wifi network? Thanks for your help.

    Can you share photos on i-photo between machines that use the same network or even between different accounts on the same machine? I know you can share music on i-tunes but can you do the same on i-photo? Thanks for your help.

    Yes.
    If you want the other user to be able to see the pics, but not add to, change or alter your library, then enable Sharing in your iPhoto (Preferences -> Sharing), leave iPhoto running and use Fast User Switching to open the other account. In that account, enable 'Look For Shared Libraries'. Your Library will appear in the other source pane.
    Any user can drag a pic from the Shared Library to their own in the iPhoto Window.
    Remember iPhoto must be running in both accounts for this to work.
    You can figure out using it with another machine from that too

  • Trying to use the same ground for more than two channels (RSE configuration) with usb 6000

    Hello,
    I'm currently trying to set up a LabView code in order to get readings of voltage using 5 different locations simultaneously. I want to only use the first location as ground and obtain 4 voltage measurements between the ground and each one of the other 4 channels. I'm using a usb 6000 which for now allows me to use the same ground for only two channels. Is there a way to use the same ground for 4 channels?
    Thank you,
    Maria

    You're right it is confusing the way I describe it so I ahve attached some pictures of the set up. The first figure is the cell filled with soil and the 5 probes inserted in it. The anode is placed at the left end of the cell and the cathode at the right end but they do not appear in the figure. I'm trying to use location 1 as gournd and take measurements of voltage from the following pairs: 1-2, 1-3, 1-4, and 1-5. The second figure is the DAQ I'm using. When I was trying to set up the RSE configuration, it was ussing ground A for the channels 6 & 7 (locations 2 and 3 in figure 1) but ground B for channels 4 & 5 (locations 4 and 5 in figure 1). What I am asking is which is the best way to use the signal from location 1 as the ground for all 4 channels. Is this more clear?
    Thank you for your time!
    Maria

  • Can you get an iphone 5 at target that uses AT&T or Verizon network and use the Straight Talk plan from Walmart?

    Can you get an iphone 5 at target that uses AT&T or Verizon network and use the Straight Talk plan from Walmart? I don't have AT&T or Verizon network and I don't want to get them but I was just wondering if you can get the iphone 5 that is at target and use it for the straight talk plan. I will be getting the straight talk plan but I would like to do some research on the iphone 5 first for straight talk. At walmart the phone is $544.99 and I think it will be a lot cheaper to buy it at target.
    Thank You!

    When I use find file http://www.macupdate.com/app/mac/30073/find-file (which does tend to find files that "Finder" can't), it's not coming up with any other itunes library files that have been modified in the past week, which I know it would have been - unfortunately, I don't have a very recent backup of the hard drive.  It would be a few months old so it wouldn't have the complete library on it....any ideas?  I'm wondering if restarting the computer might help but have been afraid to do so in case it would make it harder to recover anything...I was looking at this thread https://discussions.apple.com/thread/4211589?start=0&tstart=0 in the hopes that it might have a helpful suggestion but it's definitely a different scenario.

  • I can't make or receive calls in my iPhone 5(just bought second hand and unlocked), but I am able to use 3G network. If I use the same SIM card in other phone it works fine. I have tried network resetting and restore.

    I can't make or receive calls in my iPhone 5(just bought second hand and unlocked), but I am able to use 3G network. If I use the same SIM card in other phone it works fine. I have tried network resetting and restore.
    I bought this cheap from an unknown persons. I have checked it is not in blacklist. And unlocked by apple.

    Those are all carrier features, so contact your cell phone provider.

  • Using the same client for both regfree and out-of-proc COM

    Hi,
    Here is the context:
    1. We have the same set of COM objects that can be deployed as in-proc COM servers (dlls) or out-of-proc COM servers (exe).  In-proc servers are called through regfree COM.
    2. We have test projects that use the in-proc COM servers through regfree COM.
    I would like to use the same test client projects for both regfree and out-of-proc COM servers (but not at the same time). For example, I would like to first run the client using regfree COM, then delete the in-proc dll and register the out-of-proc com server,
    and then run the client again without having to recompile.  But I have not found a way to do this.
    Instead, what I have to do is modify the project settings of the test client project, removing the regfree stuff (the manifest dependencies) before I can use the test client project with the out-of-proc server.
    Is there a way to do this without recompiling?
    FYI, I have tried regfree COM by changing the client project's Project->Properties->Linker->Manifest file->Additional Manifest Dependencies, or by changing the client project's Project->Properties->Manifest Tool->Input and Output->Additional
    Manifest Files.  Either way works with regfree COM.  And either way I have to remove those settings before making it work with out-of-proc COM (and hence recompiling, which is what I am trying to avoid).
    Thanks,
    Nick

    Try Manifest Tool > Input and Output > Embed Manifest = No, and change Linker > Manifest File > Manifest File to drop ".intermediate" in the middle (or just rename the file after the build).
    A manifest doesn't have to be embedded into the executable, it could be a standalone file named like ApplicationName.exe.manifest and sitting in the same directory next to the .EXE. Then you can simply delete or rename it back and forth to switch between
    registered and reg-free COM.
    Igor Tandetnik

Maybe you are looking for