Configuring additonal server ports
Hi, if i'm using 2 server ports per chassis, and wish to add another 2, besides plugging in the cables and settings the ports on the interconnect for "Configure as Server Port" is there anything else that is needed and is there any disruption to traffic ?
Hello David,
Re-acknowledging the chassis does not reboot the blades. The links between IOM and FI are flapped and are included to carry traffic between blades and FI.
---->>> What about changing from individual links to port-channel, will this require a re-acknowledgement as well ?
{Padma] Depends upon where we make the change.
If you change it under Equipment > Policies > , you need to manually re-acknowledge the chassis for the links to form a port-channel.
If the global policy is set to None for " Link Grouping Preference " and we are changing the policy for specific chassis ( Equipment > Chassis X > Connectivity Policy " to port-channel, then this configuration change automatically re-acknowledges the chassis. You will get a warning before saving the changes.
Fabric port channel is available when you have FI 62XX / IOM 220X / UCSM 2.0 hardware / software combination.
--->>> Using individual links what method does the FI use for sending traffic down 1 link as opposed to the other ?
[Padma] When using individual links between IOM and FI, traffic is distributed according to pre-defined configuration based on number of physical links
Supported physical links are 1,2 4 and 8.
Let me know how your hardware model and current number of links used between IOM and FI.
Padma
Similar Messages
-
Can't configure tacacs-server port
We're unable to configure a specific port, which is required for our customer for the tacacs-server. One of the devices is a 7604 router running this image -
c7600rsp72043-adventerprisek9-mz.122-33.SRD6.bin. The other device is a 2960 switch with the following image - c2960-lanbasek9-mz.122-35.SE5.bin.
We don't get the option to add a port after the tacacs-server host x.x.x.x command.
Any ideas would be greatly appreciated!
Regards..Hi
Please go through this link, this will be helpful regarding TCSACS Authentication and Fortigate configuration:
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.2/user/guide/acsuserguide.html -
Difference between HTTP Server port and HTTP Server listen port
Hi,
What's the difference between the following?
Oracle HTTP Server port = 7780
Oracle HTTP Server listen port = 7781
They are the ports used in my 9ias 9.0.3 instance.
Please advise.
Thank you.Hi,
The server port, 7780, is port where HTTP server response and listen ports are other ports tha HTTP Server can listen. In IAS, the default configuration, the server port is response for Web Cache and Web Cache connect with HTTP Server in listen port.
Marcio Mesti -
Change/Configure Host and Port for the Web Service Proxy with Server
Hi,
Is there a way to configure Host and Port in generated proxy for Web service depending upon server. (ADF 11g)
Scenario:
We are consuming Credit Card web service from a service provider and have different Host and Port details for development, QA and Prod.
So we created proxy classes using wsdl for development and things work fine, but when deploying code to QA or Prod we need to change the Host
and Port details.
Is their a way we could user variable's for Host and Port which looks to some configuration file to evaluate their values
based on server.
I am a bit new to this web service .. will appreciate if someone could provide an example.
Thanks.Are you using Web Service Proxy or Web Service Data Control?
If you are using Web Service Proxy. Right click on your Proxy --> Properties --> Port Endpoints. Here you can change the IP & Port details for each port.
Venkat -
Weblogic Admin server port configuration
Hi All,
I want to configure the Admin server port from 7001 to 80. Since I cant access Admin console, can we change this using the config files.If so, which file I need to
modify.
Environment: Oracle Enterprise Linux
Pl. provide me some inputs.
THanks
RajHi Raj
1. By default when you create a Weblogic Domain and choose all the defaults, it uses default port as 7001. There will NOT be any entry for this in config.xml file. Look for the file named config.xml file under yourDomain/config/ folder. You will not find any word like "7001" most of the times.
The entries related to this section are something like this in addition to extra tags between <server>...</server> for example:
<server>
<name>yourAdminServerName</name>
<listen-address/>
</server>
2. Take a back up of config.xml file. Make sure Server is not running. If someting goes wrong, use this backup config.xml file to restart the server.
3. Carefully edit config.xml file, the contents inside the above tag <server>...</server> by adding a new attribute as shown below by name <listen-port>
<server>
<name>DefaultServer</name>
<listen-port>80</listen-port>
<listen-address></listen-address>
<tunneling-enabled>true</tunneling-enabled>
</server>
All you do is add this one line: <listen-port>80</listen-port> within the <server>...</server> tags.
Restart the server. Access the weblogic console like this now http://localhost:80/console or http://localhost/console (port 80 is default and we do not need to type it manually).
Thanks
Ravi Jegga
NOTE: You can change the port from Admin Console also, siince you mentioned you do not have access to console, you can manually edit config.xml file. -
FPN configured for message server port
Hello,
I would like to configure my Consumer Portal to connect to my Producer on port :8101 (the default message server port of the Producer). However, each time I try with this conifguration FPN breaks and nothing works - can't browse the PCD or see remote roles via Identity Management (when I switch the config back to point to port :50000 in the Producer object on the Consumer it works fine again). I'm not using a SAP web dispatcher between the two portals but Producer portal is indeed listening on port :8101 since I can hit it directly. Is this a limitation of FPN?
My http trace shows an ABORT message when trying to connect with the :8101 configuration.
The 8101 port is necessary to be configured in order to leverage our clustered load balanced environment which has the 8101 message server port listening and redirecting to a cluster of servers.
PatrickWhen using Remote Delta Links one can configure the SAP Message Server's RMI-P4 port (3901 by default) for RMI-P4 communication.
For the HTTP load balancing you cannot configure it to point to the HTTP port of SAP Message Server (8101 by default) only the application server's HTTP port on the Central Instance (e.g. 50000) can be used.
But don't bother yourselves with this, because SAP recommends using SAP Webdispatcher for HTTP load balancing in FPN scenario, so don't use SAP Message Server directly for HTTP load balancing in the FPN connection setup! -
Can I configure some ports on FI-6200UP GEM as server ports?
Hi,
I need your help!
I know FI-6100 doesn't support to be configured its some port on GEM as server ports.
Is it possible to configure some ports on FI-6200UP GEM as server ports?
And also, I wonder that some ports(1/9-16) on a port group(Second) can be configured as a server port(1/9-10), uplink ethernet port(1/11-12), FCoE port(1/13-14), and FC port(1/15-16).
Thanks in advance.
PaulHello Paul,
Yes, you can configure server ports on Expansion modules on FI 6200 series.
http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/gui/config/guide/2.1/b_UCSM_GUI_Configuration_Guide_2_1_chapter_0110.html#concept_A552AD7757A549FB82D16A07D0EDA1E4
--------- snip ------------
All of the port types listed are configurable on both the fixed and expansion module, including server ports, which are not configurable on the 6100 series fabric interconnect expansion module, but are configurable on the 6200 series fabric interconnect expansion module.
HTH
Padma -
Single Nexus 5548UP- FCoE configuration with multiple server ports
Hello Everyone,
I am new to Networking so please bear with me.
Here is some background information. We have a SINGLE Nexus 5548 UP switch to which we are connecting both the storage and the UCS C240 M3 servers (with CNA). Both the storage and server has 2 ports each going to this nexus switch.
We want to implement FCoE with this solution.
Below are the steps (for server ports) that I have followed to configure the nexus. But the port not logging into the SAN (no flogi) with the config.
Enable Features
config t
feature lacp
feature dot1x
feature interface-vlan
feature sshServer
feature npiv
end
Confgure Ethernet Ports - Server
configure
interface ethernet 1/17
description To_UCS_rack_server_1_FCoE_port_1
switchport mode trunk
switchport trunk native vlan 6
switchport trunk allowed vlan 1,6
spanning-tree port type edge trunk
priority-flow-control mode on
no shutdown
end
configure
interface ethernet 1/18
description To_UCS_rack_server_1_FCoE_port_2
switchport mode trunk
switchport trunk native vlan 6
switchport trunk allowed vlan 1,6
spanning-tree port type edge trunk
priority-flow-control mode on
no shutdown
end
Create VLAN
configure
vlan 6
name FCOE_VLAN
fcoe vsan 6
end
Setup FCoE QOS
configure terminal
system qos
service-policy type qos input fcoe-default-in-policy
service-policy type queuing input fcoe-default-in-policy
service-policy type queuing output fcoe-default-out-policy
service-policy type network-qos fcoe-default-nq-policy
end
Create vfc for Initiators (UCS Servers)
configure
interface vfc 17
bind interface ethernet 1/17
switchport description virtual_fiber_channel_Server1_Port1
end
configure
interface vfc 18
bind interface ethernet 1/18
switchport description virtual_fiber_channel_Server1_Port2
end
Adding vFC’s to VSAN
configure
vsan database
vsan 6 interface vfc 17
vsan 6 interface vfc 18
Create Zonesets and Zones
configure
show flogi database vsan 6 ----> Do not see any pwwn here???
show fcns database vsan 6
Any help in the regard would be highly appreciated.
Cheers,
KSFixed the issue. "switchport trunk native vlan 6" was causing the issue. Maybe the storage and Servers were not configured with proper VLAN's. I removed the native vlan and everything logged in fine.
Any how I have configured a single zone with all 3 servers pWWN's. I know single initiator zoning is the way to go.
Can you please guide me if I can move these servers in their separate zones without any outages? If it helps, all severs have 2 pWWN's. The current zoneset is active with that single zone.
Please let me know if you need any additional details.
Cheers,
KS -
Outgoing server port configuring not in Mail 3.5 - problems sending mail?
I recently upgraded from Tiger to Leopard and one of the things I noticed is that in Mail 3.5 undere Mail>Preferences>Accounts under the Account Information tab, there is no longer the ability to select or change ports for the Outgoing Server.
In Mail 2.x, there was an Advanced button that would let you choose a different port and select SSL (or not). In Mail 3.5, this feature is missing. Does anyone know if the outgoing server port can be changed? The reason I ask is that when I travel, my ISP will not accept any of my outgoing mail because I'm not using my home IP address (especially with .mac). This is usually remedied by changing to a different, less common port for the outgoing server. If I'm unable to change outgoing server ports in Mail 3.5, is this going to cause problems sending mail when I'm on the road? Any help would be appreciated. Thanks.
EdIf you pull down the bar in the outgoing mail server, you should be able to select "edit server list" and the window shows up where you can set up port.
-
Mail & IMAP : unable to use "exotics" server port ?
Hello,
I updated my IMAP configuration on server side, to change listening ports to something less usual than 993.
It's working fine on my mac, so server's configuration is OK.
But my iPhone refuses to connect to this new port, and always displays "unable to connect to ..." (using my WiFi, or 3G).
If I switch back to the usual port 993, and reconfigure the iPhone, it's OK...
Have anyone experienced the same thing, or managed to configure iPhone to connect on a specific port ?
Message was edited by: aK`Triple-click the word "telnet" in the line below on this page to select the whole line:
telnet imap.gmail.com 993
Copy the selected text to the Clipboard by pressing the key combination command-C.
Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window by pressing command-V. I've tested these instructions only with the Safari web browser. If you use another browser, you may have to press the return key after pasting.
You should almost instantly get three lines of output below what you entered, the last of which is this:
Escape character is '^]'.
If there's no output within ten seconds, consider that a failure. If you get something different from the above, please post it in a reply. You can then quit Terminal. -
Error in configuring content server
Dear All
i am configuring external content server
I have defined my content repositories using tcode OAC0. parameters are as follows:
content repository : ZXYZ ( XYZ is my content repository)
Document Area : DMS
Storage type :HTTP content Server
Version no. : 0046
HTTP Server :IP address of content server
Port No : 1090
HTTP Script :ContentServer/ContentServer.dll
after that i saved.
now when i am clicking on Test connection i am getting Connect to Host Port 1090 error: NIECONN_REFUSED
Pls Let me know any solution you have.
Thanks
sandeep sharma> now when i am clicking on Test connection i am getting Connect to Host Port 1090 error: NIECONN_REFUSED
This means that
- either the HTTP server on the target system is not running - or not listening on port 1090
- a firewall prevents accessing that port
Markus -
Hi All,
we are in a process of configure mail server in one of our sap instance.
i have done the following settings,
1. In t-code sicf under virtual host SAPCONNECT,
2. I have added in host data * : *
3.under handler list CL_SMTP_EXT_SAPCONNECT.
4. now in scot i have added my deault domain under "settings -> default domain " <company name.com>
5.on double clicking on SMTP i have added the following entries
SMTP CONNECTIONS : mail host : smtp.gmail.com
port : 465
code page : 0
SUPPORT ADDRESS TYPE : i have set internet address to *
did i miss any of the steps in configuring the SMTP mail server.
after sending the mail when i look in to t code sost the message number displays "672"
please advice how can i configure mail server for incoming and outgoing
Thanks in advance,
VardhanHello Vardhan,
I suggest you to go through the below links and cross check the configuration.
http://help.sap.com/saphelp_nw04/helpdata/en/66/9c25413fabef23e10000000a155106/content.htm
http://help.sap.com/saphelp_nw04/helpdata/en/af/73563c1e734f0fe10000000a114084/content.htm
http://help.sap.com/saphelp_470/helpdata/en/af/73563c1e734f0fe10000000a114084/content.htm
Thanks,
Siva Kumar
Edited by: Siva Kumar Arivinti on Jan 19, 2012 3:16 AM -
Cupsd's bootstrap server port not found
I've got both Samba and CUPS turned off at startup, yet I get this recurring error in the system log:
Dec 12 19:07:12 /usr/sbin/smbd: cupsd's bootstrap server port not found
Dec 12 19:07:13 /usr/sbin/smbd: cupsd's bootstrap server port not found
Dec 12 19:07:13 /usr/sbin/smbd: cupsd's bootstrap server port not found
Dec 12 19:07:14 /usr/sbin/smbd: cupsd's bootstrap server port not found
I kill smbd but it starts up again, apparently thanks to /usr/libexec/launchproxy
I'm using the default configuration files for Samba and CUPS and there is no printer set up. Using OS X 10.4.3 (not Server). repaired permissions.
this is driving me nuts...any suggestions welcome.I get that response all the time, it doesn't seem to have any relevance to anything and as far as I can tell, doesn't impair the functioning of my machine.
sometimes, too much information is too much information...
Miriam -
Can we configure SAP server installed in RHEL in windows sapmmc?
Can we configure SAP server installed in RHEL in windows sapmmc(Which is also sap server with same version and same DB)?
I have tried to configure using help from previous post in SCN ( SAP MMC in one server to control the entrie landscape ) but it is not working... As picture shown below after entering the details am clicking on add but nothing is happening...
Scenario is I have installed 4 VM's with SAP installed in all (out of it 3 linux and 1 windows) & all communicating well and they are in same Network/Landscape & I can configure/manage/logon all servers in host GUI... But If I shutdown my VM or a Laptop... Every time I have to start all the servers... by starting lsnrctl, DB, sap for all the servers,
Is there any chance to configure sap in windows sapmmc...???
Kindly suggest the process step by step...
Thanks in advance...Hi Yüksel
Thank you for the reply It helped me to configure but i struck in some place.. Dispatcher is getting stopped... I tried to add 3 different sap servers in sapmmc and tried to start.. Three are getting same errors(Guess same error)
After your suggestion i was able to configure and start SIDadm of host but immediately or after 30sec Dispatcher gets stopped tried to find out some solutions but didnt worked... But i was able to start from there servers manually in linux way startsap, but not in SAPMMC way...
Could you or please help me in solving trace given below...
trc file: "dev_disp.new", trc level: 1, release: "700"
sysno 00
sid W41
systemid 387 (Intel x86 with Linux)
relno 7000
patchlevel 0
patchno 353
intno 20050900
make: single threaded, Unicode, optimized
pid 22162
kernel runs with dp version 247000(ext=110000) (@(#) DPLIB-INT-VERSION-247000-UC)
length of sys_adm_ext is 576 bytes
*** SWITCH TRC-HIDE on ***
***LOG Q00=> DpSapEnvInit, DPStart (00 22162) [dpxxdisp.c 1345]
shared lib "dw_xml.so" version 353 successfully loaded
shared lib "dw_xtc.so" version 353 successfully loaded
shared lib "dw_stl.so" version 353 successfully loaded
shared lib "dw_gui.so" version 353 successfully loaded
shared lib "dw_mdm.so" version 353 successfully loaded
rdisp/softcancel_sequence : -> 0,5,-1
use internal message server connection to port 3900
Tue Mar 31 00:02:41 2015
*** WARNING => DpNetCheck: NiHostToAddr(www.doesnotexist0042.qqq.nxst) took 21 seconds
Tue Mar 31 00:02:52 2015
*** WARNING => DpNetCheck: NiAddrToHost(1.0.0.0) took 11 seconds
***LOG GZZ=> 2 possible network problems detected - check tracefile and adjust the DNS settings [dpxxtool2.c 5540]
MtxInit: 30000 0 0
DpSysAdmExtInit: ABAP is active
DpSysAdmExtInit: VMC (JAVA VM in WP) is not active
DpIPCInit2: start server >willsys41_W41_00 <
DpShMCreate: sizeof(wp_adm) 17120 (1712)
DpShMCreate: sizeof(tm_adm) 4480000 (22288)
DpShMCreate: sizeof(wp_ca_adm) 28800 (96)
DpShMCreate: sizeof(appc_ca_adm) 9600 (96)
DpCommTableSize: max/headSize/ftSize/tableSize=500/8/524056/524064
DpShMCreate: sizeof(comm_adm) 524064 (1036)
DpSlockTableSize: max/headSize/ftSize/fiSize/tableSize=0/0/0/0/0
DpShMCreate: sizeof(slock_adm) 0 (92)
DpFileTableSize: max/headSize/ftSize/tableSize=0/0/0/0
DpShMCreate: sizeof(file_adm) 0 (68)
DpShMCreate: sizeof(vmc_adm) 0 (1684)
DpShMCreate: sizeof(wall_adm) (38456/34360/80/184)
DpShMCreate: sizeof(gw_adm) 48
DpShMCreate: SHM_DP_ADM_KEY (addr: 0x4ed2000, size: 5141584)
DpShMCreate: allocated sys_adm at 0x4ed2000
DpShMCreate: allocated wp_adm at 0x4ed4260
DpShMCreate: allocated tm_adm_list at 0x4ed8540
DpShMCreate: allocated tm_adm at 0x4ed8570
DpShMCreate: allocated wp_ca_adm at 0x531e170
DpShMCreate: allocated appc_ca_adm at 0x53251f0
DpShMCreate: allocated comm_adm at 0x5327770
DpShMCreate: system runs without slock table
DpShMCreate: system runs without file table
DpShMCreate: allocated vmc_adm_list at 0x53a7690
DpShMCreate: allocated gw_adm at 0x53a76d0
DpShMCreate: system runs without vmc_adm
DpShMCreate: allocated ca_info at 0x53a7700
DpShMCreate: allocated wall_adm at 0x53a7790
MBUF state OFF
DpCommInitTable: init table for 500 entries
DpRqQInit: Parameter rdisp/queue_lock_level = 2
rdisp/queue_size_check_value : -> on,50,30,40,500,50,500,80
ThTaskStatus: rdisp/reset_online_during_debug 0
EmInit: MmSetImplementation( 2 ).
MM global diagnostic options set: 0
<ES> client 0 initializing ....
<ES> EsILock: use spinlock for locking
<ES> InitFreeList
<ES> block size is 1024 kByte.
Using implementation map
<EsMap> EsMapUnamFileMapInit: Initialize the memory 240 MB
Linux: Kernel supports shared memory disclaiming
Linux: using madvise(<pointer>, <size>, 9).
Linux: disclaiming for shared memory enabled
<ES> 239 blocks reserved for free list.
ES initialized.
mm.dump: set maximum dump mem to 96 MB
Tue Mar 31 00:02:53 2015
rdisp/http_min_wait_dia_wp : 1 -> 1
***LOG CPS=> DpLoopInit, ICU ( 3.0 3.0 4.0.1) [dpxxdisp.c 1752]
***LOG Q0K=> DpMsAttach, mscon ( willsys41) [dpxxdisp.c 12953]
DpStartStopMsg: send start message (myname is >willsys41_W41_00 <)
DpStartStopMsg: start msg sent
Warning: Swap space is configured quite small with 5035 MB.
It should be two times larger than the amount of RAM (3066 MB).
See note 171356 for more information.
Warning: tmpfs at /dev/shm is configured quite small with 1532 MB!
Minimum value is 2048 MB.
Recommended size is 75 % of RAM + swap.
*** INFO Shm 13 in Pool 10 59082 KB estimated 58800 KB real ( -282 KB -72 %)
CCMS: start to initalize 3.X shared alert area (first segment).
*** ERROR => DpWPCheck: W0 (pid 22217) died (severity=0, status=65280) [dpxxdisp.c 16083]
child (pid=22217) exited with exit code 255
my types changed after wp death/restart 0xbf --> 0xbe
*** ERROR => DpWPCheck: W1 (pid 22218) died (severity=0, status=65280) [dpxxdisp.c 16083]
child (pid=22218) exited with exit code 255
*** ERROR => DpWPCheck: W2 (pid 22219) died (severity=0, status=65280) [dpxxdisp.c 16083]
child (pid=22219) exited with exit code 255
*** ERROR => DpWPCheck: W3 (pid 22220) died (severity=0, status=65280) [dpxxdisp.c 16083]
child (pid=22220) exited with exit code 255
my types changed after wp death/restart 0xbe --> 0xbc
my types changed after wp death/restart 0xbc --> 0xb8
my types changed after wp death/restart 0xb8 --> 0xb0
my types changed after wp death/restart 0xb0 --> 0xa0
my types changed after wp death/restart 0xa0 --> 0x80
*** DP_FATAL_ERROR => DpWPCheck: no more work processes
*** DISPATCHER EMERGENCY SHUTDOWN ***
increase tracelevel of WPs
NiWait: sleep (10000ms) ...
NiISelect: timeout 10000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:04 2015
NiISelect: TIMEOUT occured (10000ms)
dump system status
Workprocess Table (long) Tue Mar 31 07:03:04 2015
========================
No Ty. Pid Status Cause Start Err Sem CPU Time Program Cl User Action Table
0 DIA 22217 Ended no 1 0 0
1 DIA 22218 Ended no 1 0 0
2 DIA 22219 Ended no 1 0 0
3 DIA 22220 Ended no 1 0 0
4 UPD 22221 Ended no 1 0 0
5 ENQ 22222 Ended no 1 0 0
6 BTC 22223 Ended no 1 0 0
7 BTC 22224 Ended no 1 0 0
8 SPO 22225 Ended no 1 0 0
9 UP2 22226 Ended no 1 0 0
Dispatcher Queue Statistics Tue Mar 31 07:03:04 2015
===========================
+------+--------+--------+--------+--------+--------+
| Typ | now | high | max | writes | reads |
+------+--------+--------+--------+--------+--------+
| NOWP | 4 | 4 | 2000 | 4 | 0 |
+------+--------+--------+--------+--------+--------+
| DIA | 1 | 1 | 2000 | 1 | 0 |
+------+--------+--------+--------+--------+--------+
| UPD | 0 | 0 | 2000 | 0 | 0 |
+------+--------+--------+--------+--------+--------+
| ENQ | 0 | 0 | 2000 | 0 | 0 |
+------+--------+--------+--------+--------+--------+
| BTC | 0 | 0 | 2000 | 0 | 0 |
+------+--------+--------+--------+--------+--------+
| SPO | 0 | 0 | 2000 | 0 | 0 |
+------+--------+--------+--------+--------+--------+
| UP2 | 0 | 0 | 2000 | 0 | 0 |
+------+--------+--------+--------+--------+--------+
max_rq_id 6
wake_evt_udp_now 1
wake events total 5, udp 1 ( 20%), shm 4 ( 80%)
since last update total 5, udp 1 ( 20%), shm 4 ( 80%)
Dump of tm_adm structure: Tue Mar 31 07:03:04 2015
=========================
Term uid man user term lastop mod wp ta a/i (modes)
Workprocess Comm. Area Blocks Tue Mar 31 07:03:04 2015
=============================
Slots: 300, Used: 0, Max: 0
+------+--------------+----------+-------------+
| id | owner | pid | eyecatcher |
+------+--------------+----------+-------------+
NiWait: sleep (5000ms) ...
NiISelect: timeout 5000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:10 2015
NiISelect: TIMEOUT occured (5000ms)
DpHalt: shutdown server >willsys41_W41_00 < (normal)
DpJ2eeDisableRestart
DpModState: buffer in state MBUF_OFF
NiBufSend starting
NiIWrite: hdl 2 sent data (wrt=110,pac=1,MESG_IO)
MsINiWrite: sent 110 bytes
MsIModState: change state to SHUTDOWN
DpModState: change server state from STARTING to SHUTDOWN
Switch off Shared memory profiling
ShmProtect( 57, 3 )
ShmProtect( key 57 valid )
ShmProtect( slot Index 56 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x151f000)
ShmProtect( after shmat )
ShmProtect: shmat key 57 prot 3/0 done
ShmProtect(SHM_PROFILE, SHM_PROT_RW
ShmProtect( 57, 1 )
ShmProtect( key 57 valid )
ShmProtect( slot Index 56 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x151f000)
ShmProtect( after shmat )
ShmProtect: shmat key 57 prot 1/4096 done
ShmProtect(SHM_PROFILE, SHM_PROT_RD
DpWakeUpWps: wake up all wp's
Stop work processes
Stop gateway
killing proc (22215) (SOFT_KILL)
Stop icman
killing proc (22216) (SOFT_KILL)
Terminate gui connections
wait for end of work processes
wait for end of gateway
kill(22215,0) -> ESRCH: process died
wait for end of icman
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:11 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:12 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:13 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:14 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:15 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:16 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:17 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:18 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:19 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:20 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:21 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) successful -> process alive
waiting for termination of icman ...
NiWait: sleep (1000ms) ...
NiISelect: timeout 1000ms
NiISelect: maximum fd=12
NiISelect: read-mask is NULL
NiISelect: write-mask is NULL
Tue Mar 31 00:03:23 2015
NiISelect: TIMEOUT occured (1000ms)
kill(22216,0) -> ESRCH: process died
DpStartStopMsg: send stop message (myname is >willsys41_W41_00 <)
AdGetSelfIdentRecord: > <
AdCvtRecToExt: opcode 60 (AD_SELFIDENT), ser 0, ex 0, errno 0
AdCvtRecToExt: opcode 4 (AD_STARTSTOP), ser 0, ex 0, errno 0
DpConvertRequest: net size = 189 bytes
NiBufSend starting
NiIWrite: hdl 2 sent data (wrt=562,pac=1,MESG_IO)
MsINiWrite: sent 562 bytes
send msg (len 110+452) to name -, type 4, key -
DpStartStopMsg: stop msg sent
NiBufIAlloc: malloc NIBUF-IN, to 32110 bytes
MsIBufAlloc: allocated buffer
NiIRead: hdl 2 received data (rcd=458,pac=1,MESG_IO)
NiBufIIn: NIBUF len=458
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 458 bytes
MSG received, len 110+348, flag 4, from willsys41_W41_00 , typ 0, key FFFFFFFF00000000
DpHalt: received 348 bytes from message server
NiIRead: hdl 2 received data (rcd=114,pac=1,MESG_IO)
NiBufIIn: NIBUF len=114
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 114 bytes
MSG received, len 110+4, flag 3, from MSG_SERVER , typ 0, key -
DpHalt: received 4 bytes from message server
NiIRead: hdl 2 received data (rcd=114,pac=1,MESG_IO)
NiBufIIn: NIBUF len=114
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 114 bytes
MSG received, len 110+4, flag 3, from MSG_SERVER , typ 0, key -
DpHalt: received 4 bytes from message server
NiIRead: hdl 2 received data (rcd=114,pac=1,MESG_IO)
NiBufIIn: NIBUF len=114
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 114 bytes
MSG received, len 110+4, flag 3, from MSG_SERVER , typ 0, key -
DpHalt: received 4 bytes from message server
NiIRead: hdl 2 received data (rcd=114,pac=1,MESG_IO)
NiBufIIn: NIBUF len=114
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 114 bytes
MSG received, len 110+4, flag 3, from MSG_SERVER , typ 0, key -
DpHalt: received 4 bytes from message server
NiIRead: hdl 2 received data (rcd=114,pac=1,MESG_IO)
NiBufIIn: NIBUF len=114
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 114 bytes
MSG received, len 110+4, flag 3, from MSG_SERVER , typ 0, key -
DpHalt: received 4 bytes from message server
NiIRead: hdl 2 received data (rcd=114,pac=1,MESG_IO)
NiBufIIn: NIBUF len=114
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 114 bytes
MSG received, len 110+4, flag 3, from MSG_SERVER , typ 0, key -
DpHalt: received 4 bytes from message server
NiIRead: hdl 2 received data (rcd=214,pac=1,MESG_IO)
NiBufIIn: NIBUF len=214
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 214 bytes
MSG received, len 110+104, flag 3, from MSG_SERVER , typ 0, key -
DpHalt: received 104 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 received data (rcd=274,pac=1,MESG_IO)
NiBufIIn: NIBUF len=274
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 274 bytes
MSG received, len 110+164, flag 1, from MSG_SERVER , typ 0, key -
DpHalt: received 164 bytes from message server
NiIRead: hdl 2 recv would block (errno=EAGAIN)
NiIRead: read for hdl 2 timed out (0ms)
DpHalt: no more messages from the message server
DpHalt: send keepalive to synchronize with the message server
NiBufSend starting
NiIWrite: hdl 2 sent data (wrt=114,pac=1,MESG_IO)
MsINiWrite: sent 114 bytes
send msg (len 110+4) to name MSG_SERVER, type 0, key -
MsSndName: MS_NOOP ok
Send 4 bytes to MSG_SERVER
NiIRead: hdl 2 recv would block (errno=EAGAIN)
NiIPeek: peek successful for hdl 2 (r)
NiIRead: hdl 2 received data (rcd=114,pac=1,MESG_IO)
NiBufIIn: NIBUF len=114
NiBufIIn: packet complete for hdl 2
NiBufReceive starting
MsINiRead: received 114 bytes
MSG received, len 110+4, flag 3, from MSG_SERVER , typ 0, key -
Received 4 bytes from MSG_SERVER
Received opcode MS_NOOP from msg_server, reply MSOP_OK
MsOpReceive: ok
MsSendKeepalive : keepalive sent to message server
NiIRead: hdl 2 recv would block (errno=EAGAIN)
Tue Mar 31 00:03:24 2015
NiIPeek: peek for hdl 2 timed out (r; 1000ms)
NiIRead: read for hdl 2 timed out (1000ms)
DpHalt: no more messages from the message server
DpHalt: sync with message server o.k.
detach from message server
***LOG Q0M=> DpMsDetach, ms_detach () [dpxxdisp.c 13304]
NiBufSend starting
NiIWrite: hdl 2 sent data (wrt=110,pac=1,MESG_IO)
MsINiWrite: sent 110 bytes
MsIDetach: send logout to msg_server
MsIDetach: call exit function
DpMsShutdownHook called
NiBufISelUpdate: new MODE -- (r-) for hdl 2 in set0
SiSelPSet: set events of sock 11 to: ---
NiBufISelRemove: remove hdl 2 from set0
SiSelPRemove: removed last sock 11 (pos=3)
NiSelIRemove: removed hdl 2
NiICloseHandle: shutdown and close hdl 2 / sock 11
NiBufIClose: clear extension for hdl 2
MsIDetach: detach MS-system
cleanup EM
EsCleanup ....
EsCleanup destroy slot 0
<EsMap: unlink /SAP_ES_00_000
EmCleanup() -> 0
Es2Cleanup: Cleanup ES2
ShmCreate( 76, 0, 2, 0x0xcef3328 )
ShmKeyPermission( 76 ) = 0740 (octal)
ShmDelete( 13 )
cleanup event management
cleanup shared memory/semaphores
ShmCleanup SHM_SYS_ADM_KEY
ShmCleanup( 1 )
ShmCreate( 1, 0, 2, 0x0xbf99a5e8 )
ShmProtect( 1, 3 )
ShmProtect( key 1 valid )
ShmProtect( slot Index 0 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x5e1000)
ShmProtect( after shmat )
ShmProtect: shmat key 1 prot 3/0 done
ShmCreate( 1, 0, 2, -> 0x0x5e1000 )
ShmCleanup SHM_DP_ADM_KEY
ShmCleanup( 2 )
ShmCreate( 2, 0, 2, 0x0xbf99a5e8 )
ShmProtect( 2, 3 )
ShmProtect( key 2 valid )
ShmProtect( slot Index 1 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x4ed2000)
ShmProtect( after shmat )
ShmProtect: shmat key 2 prot 3/0 done
ShmCreate( 2, 0, 2, -> 0x0x4ed2000 )
ShmCleanup SHM_DP_CA_KEY
ShmCleanup( 3 )
ShmCreate( 3, 0, 2, 0x0xbf99a5e8 )
ShmProtect( 3, 3 )
ShmProtect( key 3 valid )
ShmProtect( slot Index 2 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x1655000)
ShmProtect( after shmat )
ShmProtect: shmat key 3 prot 3/0 done
ShmCreate( 3, 0, 2, -> 0x0x1655000 )
ShmCleanup SHM_PF_KEY
ShmCleanup( 4 )
ShmCreate( 4, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 4 ) = 0740 (octal)
ShmCleanup SHM_PRES_BUF
ShmCleanup( 14 )
ShmCreate( 14, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 14 ) = 0740 (octal)
ShmCleanup SHM_CALI_BUFFER
ShmCleanup( 11 )
ShmCreate( 11, 0, 2, 0x0xbf99a5e8 )
ShmGet( 10, 11, 0, 2, 0x0xbf99a52c )
ShmCleanup SHM_DB_TBUFF
ShmCleanup( 19 )
ShmCreate( 19, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 19 ) = 0740 (octal)
ShmCleanup SHM_DB_TBUFF_P
ShmCleanup( 33 )
ShmCreate( 33, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 33 ) = 0740 (octal)
ShmCleanup SHM_DB_STBUFF
ShmCleanup( 41 )
ShmCreate( 41, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 41 ) = 0740 (octal)
ShmCleanup SHM_DB_TTBUFF
ShmCleanup( 42 )
ShmCreate( 42, 0, 2, 0x0xbf99a5e8 )
ShmGet( 40, 42, 0, 2, 0x0xbf99a52c )
ShmCreate( 40, 0, 2, 0x0xbf99a1ec )
ShmKeyPermission( 40 ) = 0740 (octal)
ShmCleanup SHM_DB_FTBUFF
ShmCleanup( 43 )
ShmCreate( 43, 0, 2, 0x0xbf99a5e8 )
ShmGet( 40, 43, 0, 2, 0x0xbf99a52c )
ShmCreate( 40, 0, 2, 0x0xbf99a1ec )
ShmKeyPermission( 40 ) = 0740 (octal)
ShmCleanup SHM_DB_SNTBUFF
ShmCleanup( 45 )
ShmCreate( 45, 0, 2, 0x0xbf99a5e8 )
ShmGet( 40, 45, 0, 2, 0x0xbf99a52c )
ShmCreate( 40, 0, 2, 0x0xbf99a1ec )
ShmKeyPermission( 40 ) = 0740 (octal)
ShmCleanup SHM_DB_IRBUFF
ShmCleanup( 44 )
ShmCreate( 44, 0, 2, 0x0xbf99a5e8 )
ShmGet( 40, 44, 0, 2, 0x0xbf99a52c )
ShmCreate( 40, 0, 2, 0x0xbf99a1ec )
ShmKeyPermission( 40 ) = 0740 (octal)
ShmCleanup SHM_DB_OBJ_BUFFER
ShmCleanup( 54 )
ShmCreate( 54, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 54 ) = 0740 (octal)
ShmCleanup SHM_DB_SYNC
ShmCleanup( 46 )
ShmCreate( 46, 0, 2, 0x0xbf99a5e8 )
ShmGet( 40, 46, 0, 2, 0x0xbf99a52c )
ShmCreate( 40, 0, 2, 0x0xbf99a1ec )
ShmKeyPermission( 40 ) = 0740 (octal)
ShmCleanup SHM_DB_CUA_BUFFER
ShmCleanup( 47 )
ShmCreate( 47, 0, 2, 0x0xbf99a5e8 )
ShmGet( 40, 47, 0, 2, 0x0xbf99a52c )
ShmCreate( 40, 0, 2, 0x0xbf99a1ec )
ShmKeyPermission( 40 ) = 0740 (octal)
ShmCleanup SHM_DB_OTR_BUFFER
ShmCleanup( 64 )
ShmCreate( 64, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 64 ) = 0740 (octal)
ShmCleanup SHM_DB_ESM_BUFFER
ShmCleanup( 65 )
ShmCreate( 65, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 65 ) = 0740 (octal)
ShmCleanup SHM_ROLL_AREA_KEY
ShmCleanup( 9 )
ShmCreate( 9, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 9 ) = 0740 (octal)
ShmCleanup SHM_PAGING_AREA_KEY
ShmCleanup( 8 )
ShmCreate( 8, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 8 ) = 0740 (octal)
ShmCleanup SHM_ROLL_ADM_KEY
ShmCleanup( 17 )
ShmCreate( 17, 0, 2, 0x0xbf99a5e8 )
ShmGet( 10, 17, 0, 2, 0x0xbf99a52c )
ShmCleanup SHM_PAGING_ADM_KEY
ShmCleanup( 18 )
ShmCreate( 18, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 18 ) = 0740 (octal)
ShmCleanup SHM_PXA_KEY
ShmCleanup( 6 )
ShmCreate( 6, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 6 ) = 0740 (octal)
ShmCleanup SHM_ENQ_TABLE_KEY
ShmCleanup( 34 )
ShmCreate( 34, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 34 ) = 0740 (octal)
ShmCleanup SHM_ENQID_KEY
ShmCleanup( 58 )
ShmCreate( 58, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 58 ) = 0740 (octal)
ShmCleanup SHM_VB_ADM_KEY
ShmCleanup( 7 )
ShmCreate( 7, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 7 ) = 0740 (octal)
ShmCleanup SHM_ES2_ADM
ShmCleanup( 76 )
ShmCreate( 76, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 76 ) = 0740 (octal)
ShmCleanup SHM_EM_ADM
ShmCleanup( 51 )
ShmCreate( 51, 0, 2, 0x0xbf99a5e8 )
ShmProtect( 51, 3 )
ShmProtect( key 51 valid )
ShmProtect( slot Index 50 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x6e14000)
ShmProtect( after shmat )
ShmProtect: shmat key 51 prot 3/0 done
ShmCreate( 51, 0, 2, -> 0x0x6e14000 )
ShmCleanup SHM_EM2_ADM
ShmCleanup( 77 )
ShmCreate( 77, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 77 ) = 0740 (octal)
ShmCleanup SHM_EG2_ADM
ShmCleanup( 78 )
ShmCreate( 78, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 78 ) = 0740 (octal)
ShmCleanup SHM_MSBUF
ShmCleanup( 52 )
ShmCreate( 52, 0, 2, 0x0xbf99a5e8 )
ShmProtect( 52, 3 )
ShmProtect( key 52 valid )
ShmProtect( slot Index 51 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x60b000)
ShmProtect( after shmat )
ShmProtect: shmat key 52 prot 3/0 done
ShmCreate( 52, 0, 2, -> 0x0x60b000 )
ShmCleanup SHM_THRUN_ADM_KEY(th run adm)
ShmCleanup( 30 )
ShmCreate( 30, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 30 ) = 0740 (octal)
ShmCleanup SHM_JAVA
ShmCleanup( 70 )
ShmCreate( 70, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 70 ) = 0740 (octal)
ShmCleanup SHM_PF_AS_KEY(Appl.Statistics)
ShmCleanup( 56 )
ShmCreate( 56, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 56 ) = 0740 (octal)
ShmCleanup SHM_PROFILE
ShmCleanup( 57 )
ShmCreate( 57, 0, 2, 0x0xbf99a5e8 )
ShmProtect( 57, 3 )
ShmProtect( key 57 valid )
ShmProtect( slot Index 56 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x151f000)
ShmProtect( after shmat )
ShmProtect: shmat key 57 prot 3/0 done
ShmCreate( 57, 0, 2, -> 0x0x151f000 )
ShmCleanup SHM_NO_BUFFER
ShmCleanup( 48 )
ShmCreate( 48, 0, 2, 0x0xbf99a5e8 )
ShmGet( 40, 48, 0, 2, 0x0xbf99a52c )
ShmCreate( 40, 0, 2, 0x0xbf99a1ec )
ShmKeyPermission( 40 ) = 0740 (octal)
removing request queue
ShmCleanup( 31 )
ShmCreate( 31, 0, 2, 0x0xbf99a5d8 )
ShmProtect( 31, 3 )
ShmProtect( key 31 valid )
ShmProtect( slot Index 30 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x573d000)
ShmProtect( after shmat )
ShmProtect: shmat key 31 prot 3/0 done
ShmCreate( 31, 0, 2, -> 0x0x573d000 )
ShmCleanup SHM_POOL_0
ShmCleanup( 10 )
ShmCreate( 10, 0, 2, 0x0xbf99a5e8 )
ShmProtect( 10, 3 )
ShmProtect( key 10 valid )
ShmProtect( slot Index 9 )
ShmProtect( Mode: 76000000 )
ShmCreate( 10, 0, 2, -> 0x0xb3723000 )
ShmCleanup SHM_DB_POOL
ShmCleanup( 40 )
ShmCreate( 40, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 40 ) = 0740 (octal)
ShmCleanup SHM_POOL_50
ShmCleanup( 50 )
ShmCreate( 50, 0, 2, 0x0xbf99a5e8 )
ShmKeyPermission( 50 ) = 0740 (octal)
MiCleanup:
ShmCleanup( 62 )
ShmCreate( 62, 0, 2, 0x0xbf99a5c8 )
ShmProtect( 62, 3 )
ShmProtect( key 62 valid )
ShmProtect( slot Index 61 )
ShmProtect( Mode: 0 )
ShmProtect( before shmdt )
ShmProtect( after shmdt )
ShmProtect( before shmat 0x8b30e000)
ShmProtect( after shmat )
ShmProtect: shmat key 62 prot 3/0 done
ShmCreate( 62, 0, 2, -> 0x0x8b30e000 )
MpiCleanup() -> 0
SemKeyPermission( 1 ) = 0740 (octal)
SemKeyPermission( 1 ) = 0740 (octal)
SemKeyPermission( 6 ) = 0740 (octal)
SemKeyPermission( 6 ) = 0740 (octal)
SemKeyPermission( 7 ) = 0740 (octal)
SemKeyPermission( 7 ) = 0740 (octal)
SemKeyPermission( 8 ) = 0740 (octal)
SemKeyPermission( 10 ) = 0740 (octal)
SemKeyPermission( 10 ) = 0740 (octal)
SemKeyPermission( 11 ) = 0740 (octal)
SemKeyPermission( 11 ) = 0740 (octal)
SemKeyPermission( 12 ) = 0740 (octal)
SemKeyPermission( 12 ) = 0740 (octal)
SemKeyPermission( 13 ) = 0740 (octal)
SemKeyPermission( 13 ) = 0740 (octal)
SemKeyPermission( 14 ) = 0740 (octal)
SemKeyPermission( 14 ) = 0740 (octal)
SemKeyPermission( 15 ) = 0740 (octal)
SemKeyPermission( 16 ) = 0740 (octal)
SemKeyPermission( 16 ) = 0740 (octal)
SemKeyPermission( 17 ) = 0740 (octal)
SemKeyPermission( 17 ) = 0740 (octal)
SemKeyPermission( 18 ) = 0740 (octal)
SemKeyPermission( 18 ) = 0740 (octal)
SemKeyPermission( 19 ) = 0740 (octal)
SemKeyPermission( 19 ) = 0740 (octal)
SemKeyPermission( 20 ) = 0740 (octal)
SemKeyPermission( 20 ) = 0740 (octal)
SemKeyPermission( 21 ) = 0740 (octal)
SemKeyPermission( 21 ) = 0740 (octal)
SemKeyPermission( 22 ) = 0740 (octal)
SemKeyPermission( 22 ) = 0740 (octal)
SemKeyPermission( 24 ) = 0740 (octal)
SemKeyPermission( 24 ) = 0740 (octal)
SemKeyPermission( 25 ) = 0740 (octal)
SemKeyPermission( 25 ) = 0740 (octal)
SemKeyPermission( 26 ) = 0740 (octal)
SemKeyPermission( 26 ) = 0740 (octal)
SemKeyPermission( 27 ) = 0740 (octal)
SemKeyPermission( 27 ) = 0740 (octal)
SemKeyPermission( 28 ) = 0740 (octal)
SemKeyPermission( 28 ) = 0740 (octal)
SemKeyPermission( 29 ) = 0740 (octal)
SemKeyPermission( 29 ) = 0740 (octal)
SemKeyPermission( 30 ) = 0740 (octal)
SemKeyPermission( 30 ) = 0740 (octal)
SemKeyPermission( 31 ) = 0740 (octal)
SemKeyPermission( 31 ) = 0740 (octal)
SemKeyPermission( 35 ) = 0740 (octal)
SemKeyPermission( 35 ) = 0740 (octal)
SemKeyPermission( 36 ) = 0740 (octal)
SemKeyPermission( 37 ) = 0740 (octal)
SemKeyPermission( 42 ) = 0740 (octal)
SemKeyPermission( 42 ) = 0740 (octal)
SemKeyPermission( 43 ) = 0740 (octal)
SemKeyPermission( 43 ) = 0740 (octal)
SemKeyPermission( 44 ) = 0740 (octal)
SemKeyPermission( 44 ) = 0740 (octal)
SemKeyPermission( 45 ) = 0740 (octal)
SemKeyPermission( 47 ) = 0740 (octal)
SemKeyPermission( 47 ) = 0740 (octal)
SemKeyPermission( 48 ) = 0740 (octal)
SemKeyPermission( 48 ) = 0740 (octal)
SemKeyPermission( 49 ) = 0740 (octal)
SemKeyPermission( 49 ) = 0740 (octal)
SemKeyPermission( 50 ) = 0740 (octal)
SemKeyPermission( 51 ) = 0740 (octal)
SemKeyPermission( 51 ) = 0740 (octal)
SemKeyPermission( 53 ) = 0740 (octal)
SemKeyPermission( 53 ) = 0740 (octal)
SemKeyPermission( 54 ) = 0740 (octal)
SemKeyPermission( 54 ) = 0740 (octal)
SemKeyPermission( 55 ) = 0740 (octal)
SemKeyPermission( 55 ) = 0740 (octal)
SemKeyPermission( 56 ) = 0740 (octal)
SemKeyPermission( 56 ) = 0740 (octal)
SemKeyPermission( 57 ) = 0740 (octal)
SemKeyPermission( 57 ) = 0740 (octal)
SemKeyPermission( 58 ) = 0740 (octal)
SemKeyPermission( 58 ) = 0740 (octal)
SemKeyPermission( 59 ) = 0740 (octal)
SemKeyPermission( 62 ) = 0740 (octal)
SemKeyPermission( 63 ) = 0740 (octal)
SemKeyPermission( 64 ) = 0740 (octal)
SemKeyPermission( 65 ) = 0740 (octal)
SemKeyPermission( 66 ) = 0740 (octal)
SemKeyPermission( 67 ) = 0740 (octal)
SemKeyPermission( 69 ) = 0740 (octal)
SemKeyPermission( 69 ) = 0740 (octal)
SemKeyPermission( 70 ) = 0740 (octal)
SemKeyPermission( 72 ) = 0740 (octal)
removing Semaphore-Management
closing connect handles (dgm + tcp)
DpDelSocketInfo: del info for socket 0 (type=2)
NiICloseHandle: shutdown and close hdl 0 / sock 8
DpDelSocketInfo: del info for socket 1 (type=1)
NiICloseHandle: shutdown and close hdl 1 / sock 9 - sock 10
***LOG Q05=> DpHalt, DPStop ( 22162) [dpxxdisp.c 11739]
*** shutdown completed - server stopped ***
Thanks in advance....
Regards,
Sundar -
We have our SMTP server under port number 141 and we should add username and password. but inside SharePoint 2013, I can only define the SMTP server name , from email, reply-to . But there are not fields to define the port number , the username and password.
So can anyone advice from where I can define the port number and other field settings for the SMTP server ?
Thanksi am no sure about user name and password. i never saw that option.
check this guide:
http://blogs.technet.com/b/tirumals/archive/2012/03/17/step-by-step-configuration-of-outgoing-emails-from-sharepoint-to-microsoft-online.aspx
http://blog.fpweb.net/configuring-an-smtp-server-for-sharepoint/#.UuANoxAo6M8
Please remember to mark your question as answered &Vote helpful,if this solves/helps your problem. ****************************************************************************************** Thanks -WS MCITP(SharePoint 2010, 2013) Blog: http://wscheema.com/blog
thanks for the reply, but in our case the SMTP is a separate server , and to connect to it i need to define the ; server IP /Name , port number, username & password. but in SharePoint there is no option to define the port number , and the links you
provide are regarding configuring SMTP server, while we already have an SMTP server but i need to connect SP with it . can you advice please?
Maybe you are looking for
-
Reading from a text file and displaying the contents with in a frame
Hi All, I am trying to read some data from a text file and display it on a AWT Frame. The contents of the text file are as follows: pcode1,pname1,price1,sname1, pcode2,pname2,price2,sname1, I am writing a method to read the contents from a text file
-
Can I use Bluetooth to connect my PC
Can I use Bluetooth to connect my laptopTo transfer pics
-
Can't write on SD card even first party apps
Since I updated my Xperia Z to the 4.4.4 kitkat using pc companion, I couldn't copy any file to SD card Searching on Google I knew their is a restrictions for third party apps but even my first party apps can't write on my SD card (32 gb). Camera app
-
Hi, Good day. I have developed a very simple page that shows the Oracle Logo and page status, the page seems to be run ok but there are many red messages or errors appear in the OC4J log tab (attached) what are those messages and do I have to do some
-
Sourced SC showing in Buyer's Worklist
Is that a standard behavior that sourced SC are visible in the Buyer's worklist in SOCO? They have zero quantity and cannot be selected for sourcing, although they are visible in there untill deleted by the buyer manually out of the Worklist. We are