Configuring Aironet 1040 with WPA2-PSK
I am attempting to configure two Aironet 1040 series wireless access points for the first time and am having some difficulty. This office does not have a RADIUS server so I would like to set them up to use WPA2 with a pre-shared key. However just how this is accomplished is not immediately apparent. I have attempted using both the command line interface and the web interface, but I get errors in both places. It doesn't seem like it is all that difficult, we're just talking about a few lines in the configuration file.
This is what I have so far:
Current configuration : 1684 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap1
logging rate-limit console 9
enable secret 5 $1$q9i9$V8Z042Zif0H7t4qN5awMM.
no aaa new-model
ip domain name Office
dot11 syslog
dot11 ssid WLAN
vlan 30
authentication open
username Cisco password 7 05280F1C2243
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid WLAN
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
ssid WLAN
antenna gain 0
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.2.2 255.255.255.0
no ip route-cache
ip default-gateway 192.168.2.1
ip http server
no ip http secure-server
ip http help-path
http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
access-list 111 permit tcp any any neq telnet
bridge 1 route ip
line con 0
access-class 111 in
line vty 0 4
access-class 111 in
login local
end
OK, I figured out some of what was going on. The admin account was set to read only instead of read/write, and both radios had not been added to my VLAN. Now I have successfully (?) configured WPA2-PSK on both wireless access points, and they are broadcasting their SSIDs, but I am unable to connect to them for an unknown reason. I am prompted for the pre shared key and then the connection fails. Hmm...
Similar Messages
-
Please post if you have WiFi with WPA2-PSK and WEP working on iPod ios4
Quite a few people seem to be having difficulty with getting WiFi with WPA2-PSK and WEP working on iPod ios4. I'd like to know if anyone does have this working. Please let us know iPod model, access point (router) model, and security settings on your setup. I'm reluctant to upgrade if I can't get WiFi because quite a few of my favorite apps need the net. Please do NOT post to this thread if your WiFi is NOT working. Thanks
I have:
1. brand new (not yet even initialized) 32GB iPod Touch
2. iPod Touch 8GB 3rd Gen
3. Netcomm gateway/router/access point with security set as noted above.
Edit: if you don't know what Gen your iPod Touch is, please see:
http://support.apple.com/specs/#ipodtouch
The easiest way to tell 2nd from 3rd gen is that 3rd gen has bluetooth (look in Settings/General -- if Bluetooth is there, your iPod is 3rd gen, if not it's 2nd gen or earler).
Message was edited by: KumbiaKidThanks a lot to all who responded. I now have registered and upgraded my brand spanking new 32GB iPod Touch to ios4. Before I updated, I registered the new iPod, set up and checked the WiFi connection as described in my OP (except that it was AES - not WEP as noted above) and it worked just fine. I then updated to ios4 and it still worked fine, with no further input from me. It just connected as it should have after the update and all internet functions connect and work as expected.
To those who have had problems, my sympathy, but the problems are clearly not due only to ios4 -- there has to be something else going on with your connections.
Message was edited by: KumbiaKid -
Connecting an ibook to accesspoint with WPA2-PSK
My Ibook, bought this year, but early (panther 10.x), have problems with connecting to my Dlink accesspoint after setting the security to WPA2-PSK.
Are there any problems with this connection from apples side? The machine is rather new, but I cant get connected ...WPA with TKIP most certainly does NOT currently provide "good enough security for the time being".
Ref: http://www.cr0.net:8040/code/network/aircrack/
AirCrack is perfectly capably of cracking WPA-PSK using TKIP. It's all about the weakness of RC4 as a cipher. AES is what we truly need. The problem is that we'll have to get Linksys and Apple to stop finger pointing long enough to figure out what the actual problem is and fix it. -
WPA2+PSK with local webauth?
Hi all, I'm trying to configure a guest wlan with WPA2+PSK and local webauth. This will authenticate against ISE and once authentication is complete dropped into a authz profile.
This is supposed to be possible per cisco's docs, however when I try to set this up on the WLAN I get the message:
Only PSK can be enabled for WPA with web-auth and Radius Nac.
Well, I've got only WPA with PSK configured. Is there any 'trick' to this config that I'm missing? I've got L2 security set to WPA+WPA2, WPA2 Policy and AES with only PSK configured. Under advanced I've got AAA override and NAC state sent to radius NAC. What else, that should be it right? I've tried it on multiple controllers with the same results every time.That error is a little confusing and I don't think is a proper description of what the WLC is trying to tell you; there are actually a couple errors you may see depending on the combination of RADIUS NAC with L3 security. Essentially, you shouldn't be able to enable RADIUS NAC if you're configured for a PSK. What exactly are you trying to accomplish? It sounds like you want ISE to perform CWA for your wireless guests, but you mention local webauth. In order to do the CWA, you will use the mac-filtering option for L2 security and set security type to None. This will allow you to specify the RADIUS NAC option correctly.
When you say that "ISE will authenticate the users", how are you planning on doing this with a PSK WLAN, or are you intending that the local webauth will use RADIUS for authentication to ISE? What is the end-user flow or experience you are expecting? ie. user connects to guest, redirects, logs in, gets appropriate access.
Please also post what version of ISE and WLC you are running so we can determine what features will and will not work. -
WPA2-PSK with open MAC authentication
Can anyone help me with the configuration of Autonomous ap with WPA2-PSK with mac authentication..?
I tried configuring and created 700 ACL. But its not workingonce i enable mac authentication "wpa-psk ascii 7 06020C234D1F5B4A511416" dissappears. :(
Model: AIR-SAP1602E-N-K9
IOS: ap1g2-k9w7-mx.152-2.JB2/ap1g2-k9w7-mx.152-2.JB2
Getting Error: WPA-PSK not supported with MAC address authentication configured -
Anyone else having WPA2-PSK issues? My MacBook Pro works flawlessly with WEP but when I recently changes my network over to WPA2-PSK it stopped connecting. I have 5 PC's that connect just fine so I know there's nothing wrong with the settings on my WAP. I did some digging and noticed that after I configure the settings for my network in System Preferences and save it; it lists my network as WPA not WPA2. I thought this just might be a gui bug so I pretty much ignored it. Well I'm guessing it's more than that. I found that if I edit my com.apple.airport.preferences.plist and change the WPA reference to WPA2 it will connect to my network. The problem I have is OS X will change it back to WPA and I will lose connection. I've searched and searched forum after forum and I can't find a solution to my problem. I've reinstalled OS X and that didn't fix the issue. I've had to resort to setting up my 802.11a channel with WEP and my 802.11g with WPA2-PSK. I really want to dump the old WEP key since I now have neighbors within my wireless range.
My router is a Netgear WGR614v2 (no laughing please). Anyone have any suggestion (besides buy a new router)?I'm new to the Mac world (have linux experience) so I could be wrong on this but isn't the Airport Utility only for configuring Apple's Airport WAP's? I don't think that would do me any good since I'm connected to a third party WAP. Am I wrong?
-
I was hoping to get some assistance on getting the 1231g to work with WPA2-PSK (AES). My laptops cannot authenticate using this config but connect fine to the 1242AG. Below are some of the specifics:
1231G
Radio Type: AIR-MP31G
IOS Ver: 12.3(8) JED
Multiple SSID
Encryption: AES
Key Management: Mandatory WPA
*Laptops can connect to SSID with WEP
Any help would be greatly appreciated.I am sorry to say this, but in order to do AES with the AP you are using, you MUST have
either an AIR-RM21A or AIR-RM22A...this ap does not have either one of these radios.
...the following excerpt is from the 12.3(2)JA release notes:
AES-CCMP
This feature supports Advanced Encryption Standard-Counter Mode with Cipher Block Chaining
Message Authentication Code Protocol (AES-CCMP). AES-CCMP is required for Wi-Fi Protected
Access 2 (WPA2) and IEEE 802.11i wireless LAN security. This feature is not supported on
350 series access points.
This feature is supported on these devices:
•1100 series access points (802.11g radio only)
•1130AG series access points
•1200 series access points (IEEE 802.11g and 802.11a radios only with the part numbers
AIR-RM21A or AIR-RM22A)
•1230AG series access points (IEEE 802.11g and 802.11a radios only with the part numbers
AIR-RM21A or AIR-RM22A)
Regards
Surendra -
Server 2008 R2 RADIUS Server with a Cisco Aironet 1040 Wireless AP
I am trying to get Server 2008 R2 RADIUS Server to work with a Cisco Aironet 1040 Wireless AP. I have installed the RADIUS server by MS standards and performed some searches on Google to configure the Cisco Aironet. I see others using a Wireless LAN Controller, which I do not have. I found this post below:
https://supportforums.cisco.com/discussion/11546056/wlc-2504-radius-2008-r2-server
But I have yet to locate a good step by step document on how to set it up and I have found so many different ways that others have set it up, but none have yet to work. I am having authentication issues that I have know of and I do not see any errors in the Windows Event Viewer and I do not know where the Acess Point stores it logs for any sort of error. Keep in mind this is the first time I am doing this. I do not have a Wireless LAN Controller and all my network / domain services are on individually built servers and not on one single server as I have seen with most of the documentation they all say the same thing by putting the Certificate Services, Domain Services (AD / ADS, etc), and NPS. I do not want that configuration and my setup should not be any different, but something is not right. I know from reading that this is not rocket science, but from someone who has never done it before this is difficult as I keep reading on and so many people do it different ways including what I have been reading according to what Cisco says to configure in the environment. Does anyone know where I can find good step by step documentation along with where I can look for logs on either device? I find that all the documentation I see on Cisco's website and from searching that it is old and outdated and not been updated in a long time so it is hard to determine what works and what does not work. I am stumped here and have been doing this for several weeks now with no luck. Thank you in advance.I did configure the Server 2008 R2 RADIUS Server using this video below:
https://www.youtube.com/watch?v=g-0MM_tK-Tk
I also referenced Technet to make sure it was configured correctly as well. I am still not sure if I am 100% setup correctly on the Windows Server side, but I for sure want to make sure I have the AP side setup correctly. Do you know of a better article for the Windows Server 2008 R2 setup? Does it matter that I do not have all the services installed on the same server? Instead I have them installed on multiple servers.
I have image number c1140-k9w7-tar.124.25d.JA1 on the AP. The part that confused me in that article, which I have seen before was the part about "Setting up access point must be configured in the authentication server as an AAA client." What is the AAA Client? I also am not aware of having Cisco Secure ACS anywhere built into the AP as that part through me off completely. Do I need to skip these steps? Thank you for help on this. -
802.1x errors from client in WLAN with WPA2 and PSK
Hello,
I have been doing a client troubleshooting and I have got some errors that does not have so much sense for me:
1)
Time :03/15/2011 14:49:54 CET Severity :ERROR Controller IP :10.x.x.x Message :802.1x authentication message received, static dynamic wep supported.
2)
Time :03/15/2011 14:49:54 CET Severity :INFO Controller IP :10.x.x.x Message :Association request received from a client has an invalid RSN IE.(One reason could be mismatch in WPA2 algorithm).
The WLAN is configured with WPA2 with AES and PSK, and during the troubleshooting several roamings have happened.
Do you have any idea why they can be produced?
I attach the complete log.
Thank you in advanced.Sounds like the clients are doing WPA with TKIP for the message number 2 for example ?
-
How to setup WPA2-PSK on aironet 1602 i
I have an AIR-SAP1602I-A-K9 WAP and I am interested in configuring it for WPA2-PSK security for WAP access. I don't see a way to do this in the GUI, does this model support that type of security? Thank you.
Yes it does support WPA2/AES. Please review this guide as it should help:
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/116599-config-wpa-psk-00.html
-Scott -
Hello,good day problem with Cisco aironet 1040 series acces point
Hello good day to all, how to configure cisco aironet 1040 series using web configuration attaching through patch cord without using the console.
if possible please send me step by step instruction, any help is gladly appreciated.
thank you in advance, More power
melhelo good day sir,
this is the first time i configure this device i am using Cisco aironet 1040 for our wireless using POE for power, and using cisco catalyst 2960 as switch
i jack the patch cord in and its goes on colored green,
the thing is how i can configure the aironet 1040 sir?
waiting for a step by step instruction,
thank you in advance
mel -
Slow connection with Cisco Aironet 1040
I have been racking my brain for a while and cannot figure out why I am not getting 144Mbps out of my Aironet 1040. I was reading a previous thread (
https://supportforums.cisco.com/thread/2141961) and set it up exactly like it said. I have set the encryption to Cipher AES CCMP and set the SSID to open authentication. I also set the SSID's key management to enable WPA (WPAv2).
I was reading that WMM has to be set. I have 3 options: Disabled, Legacy, and dot11d. If i chose dot11d I have to put in a coutry code. Problem is there are no options in the country code pull down. I cannot even manually type it in.
Another problem is that cell phones cannot connect. It keeps saying authentication fails in the log.
Any reason why I am having such slow speeds?WMM is enabled by default, or at least it should be.
What type of client are you using? Check the specs of the WNIC, and see how many spatial streams that it supports.
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered -
WLAN User Idle Timeout and WPA2-PSK authentication
Hi,
There is a WLAN for Guest users with Session Timeout of 65535 sec and User Idle Timeout of 28800 sec. The WLAN uses PSK as Layer-2 authentication and Web Auth as Layer-3 authentication. Authentication source is locally created users on the controllers (LocalEAP) - can be RADIUS through ISE as well.
(Cisco Controller) show>sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.6.130.0
RTOS Version..................................... 7.6.130.0
Bootloader Version............................... 7.6.130.0
Emergency Image Version.......................... 7.6.130.0
Build Type....................................... DATA + WPS
System Name...................................... vwlc-1
System Location.................................. Matrix
System Contact................................... IT HelpDesk Matrix
System ObjectID.................................. 1.3.6.1.4.1.9.1.1631
IP Address....................................... 10.10.10.50
System Up Time................................... 6 days 17 hrs 30 mins 26 secs
System Timezone Location......................... (GMT+10:00) Sydney, Melbourne, Canberra
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... AU - Australia
--More-- or (q)uit
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 2
Number of Active Clients......................... 0
Burned-in MAC Address............................ 00:0C:29:74:15:2F
Maximum number of APs supported.................. 200
(Cisco Controller) show> wlan 2
WLAN Identifier.................................. 2
Profile Name..................................... Matrix-LocalEAP
Network Name (SSID).............................. Matrix-LocalEAP
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
Client Profiling Status
Radius Profiling ............................ Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Local Profiling ............................. Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 65535 seconds
User Idle Timeout................................ 28800 seconds
Sleep Client..................................... disable
Sleep Client Timeout............................. 12 hours
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... vwlc-1
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
WLAN Layer2 ACL.................................. unconfigured
mDNS Status...................................... Disabled
mDNS Profile Name................................ unconfigured
DHCP Server...................................... Default
DHCP Address Assignment Required................. Enabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... 802.1P (Tag=2)
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ 10.10.10.70 1812
Accounting.................................... 10.10.10.70 1813
Interim Update............................. Disabled
Framed IPv6 Acct AVP ...................... Prefix
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Enabled (Profile 'local-eap-matrix')
Security
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Disabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Disabled
PSK..................................... Enabled
CCKM.................................... Disabled
FT-1X(802.11r).......................... Disabled
FT-PSK(802.11r)......................... Disabled
PMF-1X(802.11w)......................... Disabled
PMF-PSK(802.11w)........................ Disabled
FT Reassociation Timeout................... 20
FT Over-The-DS mode........................ Disabled
GTK Randomization.......................... Disabled
SKC Cache Support.......................... Disabled
CCKM TSF Tolerance......................... 1000
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Enabled
IPv4 ACL........................................ Unconfigured
IPv6 ACL........................................ Unconfigured
Web-Auth Flex ACL............................... Unconfigured
Web Authentication server precedence:
1............................................... local
2............................................... radius
3............................................... ldap
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Enabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
flexconnect PPPoE pass-through................ Disabled
flexconnect local-switching IP-source-guar.... Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Optional
PMF........................................... Disabled
PMF Association Comeback Time................. 1
PMF SA Query RetryTimeout..................... 200
Tkip MIC Countermeasure Hold-down Timer....... 60
Eap-params.................................... Disabled
AVC Visibilty.................................... Disabled
AVC Profile Name................................. None
Flow Monitor Name................................ None
Split Tunnel (Printers).......................... Disabled
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Enabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Disabled
802.11k Neighbor List Dual Band.................. Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
802.11u........................................ Disabled
MSAP Services.................................. Disabled
Local Policy
Priority Policy Name
The wireless user on joining the WLAN enters the PSK and than gets redirected to WLC Web Auth portal for authentication. On successful login, the user is granted access. The issue is that despite Idle Timeout being 28800 sec (8 hours), the WLC removes the client entry before 8 hours if the device goes to sleep - mostly within the first hour. Tested this on Windows 7 notebook multiple times. When the PC is put to sleep, the WLC loses its record after some time. When PC wakes up, it has to undergo Web Auth again. Debugging the client MAC generates these logs - from initial association to final clearing.
(Cisco Controller) >*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 Association received from mobile on BSSID 00:26:cb:4c:89:d1
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 Global 200 Clients are allowed to AP radio
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 Max Client Trap Threshold: 0 cur: 1
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 override for default ap group, marking intgrp NULL
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 Applying Interface policy on Mobile, role Local. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 10
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 Re-applying interface policy for client
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 10.10.1.130 WEBAUTH_REQD (8) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 10.10.1.130 WEBAUTH_REQD (8) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 In processSsidIE:4850 setting Central switched to FALSE
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 Applying site-specific Local Bridging override for station 3c:a9:f4:0b:91:70 - vapId 2, site 'default-group', interface 'management'
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 Applying Local Bridging Interface Policy for station 3c:a9:f4:0b:91:70 - vlan 10, interface id 0, interface 'management'
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 STA - rates (6): 152 36 176 72 96 108 0 0 0 0 0 0 0 0 0 0
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 Processing RSN IE type 48, length 22 for mobile 3c:a9:f4:0b:91:70
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 AID 1 in Assoc Req from flex AP 00:26:cb:4c:89:d0 is same as in mscb 3c:a9:f4:0b:91:70
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 apfMs1xStateDec
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 10.10.1.130 WEBAUTH_REQD (8) Change state to START (0) last state WEBAUTH_REQD (8)
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 pemApfAddMobileStation2: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 10.10.1.130 START (0) Initializing policy
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 10.10.1.130 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 10.10.1.130 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 Encryption policy is set to 0x80000001
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 Central switch is FALSE
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 Sending Local Switch flag = 1
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 10.10.1.130 8021X_REQD (3) DHCP Not required on AP 00:26:cb:4c:89:d0 vapId 2 apVapId 2for this client
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 10.10.1.130 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 00:26:cb:4c:89:d0 vapId 2 apVapId 2 flex-acl-name:
*apfMsConnTask_0: Feb 04 07:48:10.562: 3c:a9:f4:0b:91:70 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 3c:a9:f4:0b:91:70 on AP 00:26:cb:4c:89:d0 from Associated to Associated
*apfMsConnTask_0: Feb 04 07:48:10.563: 3c:a9:f4:0b:91:70 apfPemAddUser2:session timeout forstation 3c:a9:f4:0b:91:70 - Session Tout 65535, apfMsTimeOut '65535' and sessionTimerRunning flag is 0
*apfMsConnTask_0: Feb 04 07:48:10.563: 3c:a9:f4:0b:91:70 Scheduling deletion of Mobile Station: (callerId: 49) in 65535 seconds
*apfMsConnTask_0: Feb 04 07:48:10.563: 3c:a9:f4:0b:91:70 Func: apfPemAddUser2, Ms Timeout = 65535, Session Timeout = 65535
*apfMsConnTask_0: Feb 04 07:48:10.563: 3c:a9:f4:0b:91:70 Sending Assoc Response to station on BSSID 00:26:cb:4c:89:d1 (status 0) ApVapId 2 Slot 0
*apfMsConnTask_0: Feb 04 07:48:10.563: 3c:a9:f4:0b:91:70 apfProcessAssocReq (apf_80211.c:8294) Changing state for mobile 3c:a9:f4:0b:91:70 on AP 00:26:cb:4c:89:d0 from Associated to Associated
*pemReceiveTask: Feb 04 07:48:10.563: 3c:a9:f4:0b:91:70 10.10.1.130 Removed NPU entry.
*spamApTask7: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 Sent 1x initiate message to multi thread task for mobile 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 Creating a PKC PMKID Cache entry for station 3c:a9:f4:0b:91:70 (RSN 2)
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 Resetting MSCB PMK Cache Entry 0 for station 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 Removing BSSID 00:26:cb:4c:89:d1 from PMKID cache of station 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 Setting active key cache index 0 ---> 8
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 Adding BSSID 00:26:cb:4c:89:d1 to PMKID cache at index 0 for station 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: New PMKID: (16)
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: [0000] 67 67 8f 7d 2a 8d 78 f9 6d 29 c7 74 d2 fd 6a 25
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 Initiating RSN PSK to mobile 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 EAP-PARAM Debug - eap-params for Wlan-Id :2 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 dot1x - moving mobile 3c:a9:f4:0b:91:70 into Force Auth state
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 Skipping EAP-Success to mobile 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 EAPOL Header:
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 00000000: 02 03 5f 00 .._.
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 Found an cache entry for BSSID 00:26:cb:4c:89:d1 in PMKID cache at index 0 of station 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 Found an cache entry for BSSID 00:26:cb:4c:89:d1 in PMKID cache at index 0 of station 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: [0000] 67 67 8f 7d 2a 8d 78 f9 6d 29 c7 74 d2 fd 6a 25
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 Starting key exchange to mobile 3c:a9:f4:0b:91:70, data packets will be dropped
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 Sending EAPOL-Key Message to mobile 3c:a9:f4:0b:91:70
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 Sending EAPOL-Key Message to mobile 3c:a9:f4:0b:91:70
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 Allocating EAP Pkt for retransmission to mobile 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 mscb->apfMsLwappLradNhMac = 00:0c:29:e4:e9:6a mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 mscb->apfMsBssid = 00:26:cb:4c:89:d0 mscb->apfMsAddress = 3c:a9:f4:0b:91:70 mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 10 mscb->apfMsLwappMwarInet.ipv4.addr = 168430130
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.566: 3c:a9:f4:0b:91:70 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 168427904 mscb->apfMsLwappLradPort = 41879
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.567: 3c:a9:f4:0b:91:70 Received EAPOL-Key from mobile 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.568: 3c:a9:f4:0b:91:70 Ignoring invalid EAPOL version (1) in EAPOL-key message from mobile 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.568: 3c:a9:f4:0b:91:70 Received EAPOL-key in PTK_START state (message 2) from mobile 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.568: 3c:a9:f4:0b:91:70 Stopping retransmission timer for mobile 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.568: 3c:a9:f4:0b:91:70 EAPOL Header:
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.568: 00000000: 02 03 5f 00 .._.
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.568: 3c:a9:f4:0b:91:70 Sending EAPOL-Key Message to mobile 3c:a9:f4:0b:91:70
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.568: 3c:a9:f4:0b:91:70 Sending EAPOL-Key Message to mobile 3c:a9:f4:0b:91:70
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.568: 3c:a9:f4:0b:91:70 Reusing allocated memory for EAP Pkt for retransmission to mobile 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.568: 3c:a9:f4:0b:91:70 mscb->apfMsLwappLradNhMac = 00:0c:29:e4:e9:6a mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.568: 3c:a9:f4:0b:91:70 mscb->apfMsBssid = 00:26:cb:4c:89:d0 mscb->apfMsAddress = 3c:a9:f4:0b:91:70 mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.568: 3c:a9:f4:0b:91:70 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 10 mscb->apfMsLwappMwarInet.ipv4.addr = 168430130
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.568: 3c:a9:f4:0b:91:70 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 168427904 mscb->apfMsLwappLradPort = 41879
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 Received EAPOL-Key from mobile 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 Ignoring invalid EAPOL version (1) in EAPOL-key message from mobile 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 Stopping retransmission timer for mobile 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 Freeing EAP Retransmit Bufer for mobile 3c:a9:f4:0b:91:70
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 apfMs1xStateInc
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 10.10.1.130 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state 8021X_REQD (3)
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 Central switch is FALSE
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 Sending the Central Auth Info
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 Central Auth Info Allocated PMKLen = 32
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 PMK: pmkActiveIndex = 0
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
apfMsEntryType = 0 apfMsEapType = 0
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 Sending Local Switch flag = 1
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 10.10.1.130 L2AUTHCOMPLETE (4) DHCP Not required on AP 00:26:cb:4c:89:d0 vapId 2 apVapId 2for this client
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 Not Using WMM Compliance code qosCap 00
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 10.10.1.130 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 00:26:cb:4c:89:d0 vapId 2 apVapId 2 flex-acl-name:
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 10.10.1.130 L2AUTHCOMPLETE (4) Change state to WEBAUTH_REQD (8) last state L2AUTHCOMPLETE (4)
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 10.10.1.130 WEBAUTH_REQD (8) pemAdvanceState2 6236, Adding TMP rule
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 10.10.1.130 WEBAUTH_REQD (8) Adding Fast Path rule
type = Airespace AP Client - ACL passthru
on AP 00:26:cb:4c:89:d0, slot 0, interface = 1, QOS = 0
IPv4 ACL ID
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 10.10.1.130 WEBAUTH_REQD (8) Fast Path rule (contd...) 802.1P = 2, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 10, Local Bridging intf id = 0
*Dot1x_NW_MsgTask_0: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 10.10.1.130 WEBAUTH_REQD (8) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*spamApTask7: Feb 04 07:48:10.569: 3c:a9:f4:0b:91:70 spamEncodeCentralAuthInoMsPayload: msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
apfMsEntryType = 0 pmkLen = 32
*pemReceiveTask: Feb 04 07:48:10.570: 3c:a9:f4:0b:91:70 10.10.1.130 Added NPU entry of type 2, dtlFlags 0x0
*pemReceiveTask: Feb 04 07:48:10.570: 3c:a9:f4:0b:91:70 Pushing IPv6: fe80:0000:0000:0000:c915:4a8e:6d1a:e20d , and MAC: 3C:A9:F4:0B:91:70 , Binding to Data Plane. SUCCESS !!
*DHCP Socket Task: Feb 04 07:48:10.589: 3c:a9:f4:0b:91:70 DHCP received op BOOTREPLY (2) (len 308,vlan 10, port 1, encap 0xec03)
*DHCP Socket Task: Feb 04 07:48:10.589: 3c:a9:f4:0b:91:70 DHCP processing DHCP ACK (5)
*DHCP Socket Task: Feb 04 07:48:10.589: 3c:a9:f4:0b:91:70 DHCP op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*DHCP Socket Task: Feb 04 07:48:10.589: 3c:a9:f4:0b:91:70 DHCP xid: 0xcce207f6 (3437365238), secs: 0, flags: 0
*DHCP Socket Task: Feb 04 07:48:10.589: 3c:a9:f4:0b:91:70 DHCP chaddr: 3c:a9:f4:0b:91:70
*DHCP Socket Task: Feb 04 07:48:10.589: 3c:a9:f4:0b:91:70 DHCP ciaddr: 0.0.0.0, yiaddr: 10.10.1.130
*DHCP Socket Task: Feb 04 07:48:10.589: 3c:a9:f4:0b:91:70 DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*DHCP Socket Task: Feb 04 07:48:10.589: 3c:a9:f4:0b:91:70 DHCP server id: 10.10.1.20 rcvd server id: 10.10.1.20
*SNMPTask: Feb 04 07:48:16.594: 3c:a9:f4:0b:91:70 Central Switch = FALSE
*SNMPTask: Feb 04 07:48:16.594: 3c:a9:f4:0b:91:70 Central Switch = FALSE
*SNMPTask: Feb 04 07:48:16.595: 3c:a9:f4:0b:91:70 Central Switch = FALSE
*SNMPTask: Feb 04 07:48:16.595: 3c:a9:f4:0b:91:70 Central Switch = FALSE
*ewmwebWebauth1: Feb 04 07:48:31.129: 3c:a9:f4:0b:91:70 Username entry (local1) created for mobile, length = 6
*ewmwebWebauth1: Feb 04 07:48:31.130: 3c:a9:f4:0b:91:70 Username entry (local1) created in mscb for mobile, length = 6
*ewmwebWebauth1: Feb 04 07:48:31.130: 3c:a9:f4:0b:91:70 10.10.1.130 WEBAUTH_REQD (8) Change state to WEBAUTH_NOL3SEC (14) last state WEBAUTH_REQD (8)
*ewmwebWebauth1: Feb 04 07:48:31.130: 3c:a9:f4:0b:91:70 apfMsRunStateInc
*ewmwebWebauth1: Feb 04 07:48:31.130: 3c:a9:f4:0b:91:70 10.10.1.130 WEBAUTH_NOL3SEC (14) Change state to RUN (20) last state WEBAUTH_NOL3SEC (14)
*ewmwebWebauth1: Feb 04 07:48:31.130: 3c:a9:f4:0b:91:70 Session Timeout is 65535 - starting session timer for the mobile
*ewmwebWebauth1: Feb 04 07:48:31.130: 3c:a9:f4:0b:91:70 10.10.1.130 RUN (20) Reached PLUMBFASTPATH: from line 6571
*ewmwebWebauth1: Feb 04 07:48:31.131: 3c:a9:f4:0b:91:70 10.10.1.130 RUN (20) Replacing Fast Path rule
type = Airespace AP Client
on AP 00:26:cb:4c:89:d0, slot 0, interface = 1, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID =
*ewmwebWebauth1: Feb 04 07:48:31.131: 3c:a9:f4:0b:91:70 10.10.1.130 RUN (20) Fast Path rule (contd...) 802.1P = 2, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 10, Local Bridging intf id = 0
*ewmwebWebauth1: Feb 04 07:48:31.131: 3c:a9:f4:0b:91:70 10.10.1.130 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*pemReceiveTask: Feb 04 07:48:31.132: 3c:a9:f4:0b:91:70 10.10.1.130 Added NPU entry of type 1, dtlFlags 0x0
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >*pemReceiveTask: Feb 04 07:48:31.132: 3c:a9:f4:0b:91:70 Pushing IPv6: fe80:0000:0000:0000:c915:4a8e:6d1a:e20d , and MAC: 3C:A9:F4:0B:91:70 , Binding to Data Plane. SUCCESS !!
*emWeb: Feb 04 07:49:14.120: 3c:a9:f4:0b:91:70 Central Switch = FALSE
*emWeb: Feb 04 07:49:14.120: 3c:a9:f4:0b:91:70 Central Switch = FALSE
*emWeb: Feb 04 07:49:14.120: 3c:a9:f4:0b:91:70 Central Switch = FALSE
*SNMPTask: Feb 04 07:51:19.646: 3c:a9:f4:0b:91:70 Central Switch = FALSE
*SNMPTask: Feb 04 07:51:19.646: 3c:a9:f4:0b:91:70 Central Switch = FALSE
*SNMPTask: Feb 04 07:51:19.662: 3c:a9:f4:0b:91:70 Central Switch = FALSE
*SNMPTask: Feb 04 07:51:19.662: 3c:a9:f4:0b:91:70 Central Switch = FALSE
*SNMPTask: Feb 04 07:51:19.663: 3c:a9:f4:0b:91:70 Central Switch = FALSE
*SNMPTask: Feb 04 07:51:19.663: 3c:a9:f4:0b:91:70 Central Switch = FALSE
*IPv6_Msg_Task: Feb 04 07:53:35.661: 3c:a9:f4:0b:91:70 Link Local address fe80::c915:4a8e:6d1a:e20d updated to mscb. Not Advancing pem state.Current state: mscb in apfMsMmInitial mobility state and client state APF_MS_STATE_A
*dot1xMsgTask: Feb 04 07:54:26.664: GTK Rotation Kicked in for AP: 00:26:cb:4c:89:d0 SlotId = 1 - (0x47440ef0)
*dot1xMsgTask: Feb 04 07:54:26.665: Generated a new group key for AP 00:26:cb:4c:89:d0(1) - vap 1
*dot1xMsgTask: Feb 04 07:54:26.665: Sending of M5 for 00:26:cb:4c:89:d0 is Skipped, rc = 1
*dot1xMsgTask: Feb 04 07:54:26.665: Generated a new group key for AP 00:26:cb:4c:89:d0(1) - vap 2
*dot1xMsgTask: Feb 04 07:54:26.665: Sending of M5 for 00:26:cb:4c:89:d0 is Skipped, rc = 1
*SNMPTask: Feb 04 07:56:19.689: 3c:a9:f4:0b:91:70 Central Switch = FALSE
*SNMPTask: Feb 04 07:56:19.689: 3c:a9:f4:0b:91:70 Central Switch = FALSE
*SNMPTask: Feb 04 08:01:19.730: 3c:a9:f4:0b:91:70 Central Switch = FALSE
*SNMPTask: Feb 04 08:01:19.730: 3c:a9:f4:0b:91:70 Central Switch = FALSE
*dot1xMsgTask: Feb 04 08:01:23.904: GTK Rotation Kicked in for AP: 00:26:cb:4c:89:d0 SlotId = 0 - (0x47440ef0)
*dot1xMsgTask: Feb 04 08:01:23.904: Generated a new group key for AP 00:26:cb:4c:89:d0(0) - vap 1
*dot1xMsgTask: Feb 04 08:01:23.905: Sending of M5 for 00:26:cb:4c:89:d0 is Skipped, rc = 1
*dot1xMsgTask: Feb 04 08:01:23.905: Generated a new group key for AP 00:26:cb:4c:89:d0(0) - vap 2
*dot1xMsgTask: Feb 04 08:01:23.905: GTK rotation for 3c:a9:f4:0b:91:70
*dot1xMsgTask: Feb 04 08:01:23.905: 3c:a9:f4:0b:91:70 EAPOL Header:
*dot1xMsgTask: Feb 04 08:01:23.905: 00000000: 02 03 5f 00 .._.
*dot1xMsgTask: Feb 04 08:01:23.905: 3c:a9:f4:0b:91:70 Key exchange done, data packets from mobile 3c:a9:f4:0b:91:70 should be forwarded shortly
*dot1xMsgTask: Feb 04 08:01:23.905: 3c:a9:f4:0b:91:70 Key exchange done, data packets from mobile 3c:a9:f4:0b:91:70 should be forwarded shortly
*dot1xMsgTask: Feb 04 08:01:23.906: Confirmation Key: (16)
*dot1xMsgTask: Feb 04 08:01:23.906: [0000] fa a3 68 28 46 1f 49 18 a0 60 7a 92 c4 f5 64 3d
*dot1xMsgTask: Feb 04 08:01:23.906: 3c:a9:f4:0b:91:70 Sending EAPOL-Key Message to mobile 3c:a9:f4:0b:91:70
state PTKINITDONE (message 5 - group), replay counter 00.00.00.00.00.00.00.02
*dot1xMsgTask: Feb 04 08:01:23.906: 3c:a9:f4:0b:91:70 Sending EAPOL-Key Message to mobile 3c:a9:f4:0b:91:70
state PTKINITDONE (message 5 - group), replay counter 00.00.00.00.00.00.00.02
*dot1xMsgTask: Feb 04 08:01:23.906: 3c:a9:f4:0b:91:70 Allocating EAP Pkt for retransmission to mobile 3c:a9:f4:0b:91:70
*dot1xMsgTask: Feb 04 08:01:23.906: 3c:a9:f4:0b:91:70 mscb->apfMsLwappLradNhMac = 00:0c:29:e4:e9:6a mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: Feb 04 08:01:23.906: 3c:a9:f4:0b:91:70 mscb->apfMsBssid = 00:26:cb:4c:89:d0 mscb->apfMsAddress = 3c:a9:f4:0b:91:70 mscb->apfMsApVapId = 2
*dot1xMsgTask: Feb 04 08:01:23.907: 3c:a9:f4:0b:91:70 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 1 mscb->apfMsLwappLradVlanId = 10 mscb->apfMsLwappMwarInet.ipv4.addr = 168430130
*dot1xMsgTask: Feb 04 08:01:23.907: 3c:a9:f4:0b:91:70 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 168427904 mscb->apfMsLwappLradPort = 41879
*dot1xMsgTask: Feb 04 08:01:23.907: 3c:a9:f4:0b:91:70 Updated broadcast key sent to mobile 3C:A9:F4:0B:91:70
*dot1xMsgTask: Feb 04 08:01:23.907: 3c:a9:f4:0b:91:70 Updated broadcast key sent to mobile 3C:A9:F4:0B:91:70
*dot1xMsgTask: Feb 04 08:01:23.907: Sending of M5 for 00:26:cb:4c:89:d0 is Skipped, rc = 1
*osapiBsnTimer: Feb 04 08:01:25.104: 3c:a9:f4:0b:91:70 802.1x 'timeoutEvt' Timer expired for station 3c:a9:f4:0b:91:70 and for message = M5
*dot1xMsgTask: Feb 04 08:01:25.104: 3c:a9:f4:0b:91:70 Retransmit 1 of EAPOL-Key M5 (length 131) for mobile 3c:a9:f4:0b:91:70
*dot1xMsgTask: Feb 04 08:01:25.104: 3c:a9:f4:0b:91:70 mscb->apfMsLwappLradNhMac = 00:0c:29:e4:e9:6a mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: Feb 04 08:01:25.104: 3c:a9:f4:0b:91:70 mscb->apfMsBssid = 00:26:cb:4c:89:d0 mscb->apfMsAddress = 3c:a9:f4:0b:91:70 mscb->apfMsApVapId = 2
*dot1xMsgTask: Feb 04 08:01:25.104: 3c:a9:f4:0b:91:70 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 1 mscb->apfMsLwappLradVlanId = 10 mscb->apfMsLwappMwarInet.ipv4.addr = 168430130
*dot1xMsgTask: Feb 04 08:01:25.104: 3c:a9:f4:0b:91:70 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 168427904 mscb->apfMsLwappLradPort = 41879
*osapiBsnTimer: Feb 04 08:01:26.104: 3c:a9:f4:0b:91:70 802.1x 'timeoutEvt' Timer expired for station 3c:a9:f4:0b:91:70 and for message = M5
*dot1xMsgTask: Feb 04 08:01:26.104: 3c:a9:f4:0b:91:70 Retransmit 2 of EAPOL-Key M5 (length 131) for mobile 3c:a9:f4:0b:91:70
*dot1xMsgTask: Feb 04 08:01:26.104: 3c:a9:f4:0b:91:70 mscb->apfMsLwappLradNhMac = 00:0c:29:e4:e9:6a mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: Feb 04 08:01:26.104: 3c:a9:f4:0b:91:70 mscb->apfMsBssid = 00:26:cb:4c:89:d0 mscb->apfMsAddress = 3c:a9:f4:0b:91:70 mscb->apfMsApVapId = 2
*dot1xMsgTask: Feb 04 08:01:26.104: 3c:a9:f4:0b:91:70 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 1 mscb->apfMsLwappLradVlanId = 10 mscb->apfMsLwappMwarInet.ipv4.addr = 168430130
*dot1xMsgTask: Feb 04 08:01:26.104: 3c:a9:f4:0b:91:70 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 168427904 mscb->apfMsLwappLradPort = 41879
*osapiBsnTimer: Feb 04 08:01:27.104: 3c:a9:f4:0b:91:70 802.1x 'timeoutEvt' Timer expired for station 3c:a9:f4:0b:91:70 and for message = M5
*dot1xMsgTask: Feb 04 08:01:27.104: 3c:a9:f4:0b:91:70 Retransmit failure for EAPOL-Key M5 to mobile 3c:a9:f4:0b:91:70, retransmit count 3, mscb deauth count 0
*dot1xMsgTask: Feb 04 08:01:27.104: 3c:a9:f4:0b:91:70 Resetting MSCB PMK Cache Entry 0 for station 3c:a9:f4:0b:91:70
*dot1xMsgTask: Feb 04 08:01:27.105: 3c:a9:f4:0b:91:70 Removing BSSID 00:26:cb:4c:89:d1 from PMKID cache of station 3c:a9:f4:0b:91:70
*dot1xMsgTask: Feb 04 08:01:27.105: 3c:a9:f4:0b:91:70 Setting active key cache index 0 ---> 8
*dot1xMsgTask: Feb 04 08:01:27.105: 3c:a9:f4:0b:91:70 Sent Deauthenticate to mobile on BSSID 00:26:cb:4c:89:d0 slot 0(caller 1x_ptsm.c:598)
*dot1xMsgTask: Feb 04 08:01:27.105: 3c:a9:f4:0b:91:70 Setting active key cache index 8 ---> 8
*dot1xMsgTask: Feb 04 08:01:27.105: 3c:a9:f4:0b:91:70 Deleting the PMK cache when de-authenticating the client.
*dot1xMsgTask: Feb 04 08:01:27.105: 3c:a9:f4:0b:91:70 Global PMK Cache deletion failed.
*dot1xMsgTask: Feb 04 08:01:27.106: 3c:a9:f4:0b:91:70 Scheduling deletion of Mobile Station: (callerId: 57) in 10 seconds
*dot1xMsgTask: Feb 04 08:01:27.106: 3c:a9:f4:0b:91:70 Freeing EAP Retransmit Bufer for mobile 3c:a9:f4:0b:91:70
*osapiBsnTimer: Feb 04 08:01:37.105: 3c:a9:f4:0b:91:70 apfMsExpireCallback (apf_ms.c:626) Expiring Mobile!
*apfReceiveTask: Feb 04 08:01:37.105: 3c:a9:f4:0b:91:70 apfMsExpireMobileStation (apf_ms.c:6655) Changing state for mobile 3c:a9:f4:0b:91:70 on AP 00:26:cb:4c:89:d0 from Associated to Disassociated
*apfReceiveTask: Feb 04 08:01:37.105: 3c:a9:f4:0b:91:70 Scheduling deletion of Mobile Station: (callerId: 45) in 10 seconds
*osapiBsnTimer: Feb 04 08:01:47.105: 3c:a9:f4:0b:91:70 apfMsExpireCallback (apf_ms.c:626) Expiring Mobile!
*apfReceiveTask: Feb 04 08:01:47.106: 3c:a9:f4:0b:91:70 Sent Deauthenticate to mobile on BSSID 00:26:cb:4c:89:d0 slot 0(caller apf_ms.c:6749)
*apfReceiveTask: Feb 04 08:01:47.106: 3c:a9:f4:0b:91:70 Setting active key cache index 8 ---> 8
*apfReceiveTask: Feb 04 08:01:47.106: 3c:a9:f4:0b:91:70 Deleting the PMK cache when de-authenticating the client.
*apfReceiveTask: Feb 04 08:01:47.106: 3c:a9:f4:0b:91:70 Global PMK Cache deletion failed.
*apfReceiveTask: Feb 04 08:01:47.106: 3c:a9:f4:0b:91:70 apfMsAssoStateDec
*apfReceiveTask: Feb 04 08:01:47.106: 3c:a9:f4:0b:91:70 apfMsExpireMobileStation (apf_ms.c:6787) Changing state for mobile 3c:a9:f4:0b:91:70 on AP 00:26:cb:4c:89:d0 from Disassociated to Idle
*apfReceiveTask: Feb 04 08:01:47.106: 3c:a9:f4:0b:91:70 Scheduling deletion of Mobile Station: (callerId: 47) in 10 seconds
*osapiBsnTimer: Feb 04 08:01:57.106: 3c:a9:f4:0b:91:70 apfMsExpireCallback (apf_ms.c:626) Expiring Mobile!
*apfReceiveTask: Feb 04 08:01:57.106: 3c:a9:f4:0b:91:70 pemApfDeleteMobileStation2: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
*apfReceiveTask: Feb 04 08:01:57.106: 3c:a9:f4:0b:91:70 10.10.1.130 START (0) Deleted mobile LWAPP rule on AP [00:26:cb:4c:89:d0]
*apfReceiveTask: Feb 04 08:01:57.106: 3c:a9:f4:0b:91:70 Username entry deleted for mobile
*apfReceiveTask: Feb 04 08:01:57.106: 3c:a9:f4:0b:91:70 Deleting mobile on AP 00:26:cb:4c:89:d0(0)
If Layer-2 Auth (PSK) is set to "none" and only Layer-3 Web Auth is kept, then there are no issues. PC can wake up before 8 hours and not prompted for Web Auth again. As a test, I setup the WLAN with Layer-2 PSK auth only with Layer-3 auth set to none. The WLC removed the client entry after 25 minutes. Not an issue for PSK based auth only as PC on wake up seamlessly gets associated to WLAN.
Is User Idle Timeout setting not valid when WPA2-PSK is used as the auth method ?
Thanks,
Rick.Thanks Scott, The code version is 7.6.130.0 which supports Sleeping Client feature. However, as per the docu "http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-6/configuration-guide/b_cg76/b_cg76_chapter_010111.html#reference_7008E6F7D7094BA7AD39491D7361622D"
The authentication of sleeping clients feature is not supported with Layer 2 security and web authentication enabled.
and as you mentioned as well
...Sleeping client like George mentioned is a better way than adjusting the idle timer but strictly for layer 3 only...
Sleeping Client wasn't an option in my case. That is why I was hoping that Idle Timeout may do the trick here. This is an actual case where a client with an existing wireless network just wanted to enable sleeping client feature so that their guests don't need to re-auth if their device sleeps or they go out (break) and come back after some time. Layer-3 Web Auth alone should be enough I think. Keeping L2-PSK is probably their security team's decision, as they also use the same SSID for BYOD devices and don't want nearby people/buildings to see that there is an Open Wifi available and on joining would see the Web Auth portal and company disclaimer.
George, I agree with Dot1X method. It can be used for the BYOD devices (separate SSID) while we can keep the Guest WLAN as L3-WebAuth only on controller (or do CWA through ISE if available).
Thanks for all your help.
Rick. -
Greetings -
I currently have a Cisco AIR-AP1231G-A-K9 that is running IOS version 12.3(8)JEA1. I am trying to setup WPA2 "Personal" (WPA2-PSK) with a client running Windows XP SP2. The WLAN Nic is a Cisco a/b/g PCMCIA, driver version 2.5.0.22. I have configured the PSK on both the AP and the client and verified that I did not make a typing mistake. I have installed the Microsoft WPA2 hotfix to see if that was causing the problem but it is not. The actual problem is that the client says it's "Authenticated" but will not allow any traffic to pass through. Whenever I created an SSID NOT using WPA2-PSK, the client can ge an IP address and things function normally. Here is the current AP configuration:
sh run
Building configuration...
Current configuration : 4170 bytes
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP1
enable secret ****
ip subnet-zero
no aaa new-model
dot11 vlan-name Joes-VLANofFUN vlan 237
dot11 vlan-name Joes-VLANofFUN-PartII vlan 238
dot11 ssid -=b0Gg$=-
vlan 237
authentication open
--More-- authentication key-management wpa
wpa-psk ascii ****
username Cisco password ****
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 237 mode ciphers aes-ccm
ssid -=b0Gg$=-
--More-- speed basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
no power client local
power client 50
power local cck 50
power local ofdm 30
station-role root
bridge-group 1
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.237
encapsulation dot1Q 237
no ip redirects
no ip unreachables
no ip proxy-arp
no ip route-cache
no cdp enable
bridge-group 237
bridge-group 237 subscriber-loop-control
bridge-group 237 block-unknown-source
--More-- no bridge-group 237 source-learning
no bridge-group 237 unicast-flooding
bridge-group 237 spanning-disabled
interface FastEthernet0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
no ip route-cache
speed 100
full-duplex
hold-queue 160 in
interface FastEthernet0.237
encapsulation dot1Q 237
no ip redirects
no ip unreachables
no ip proxy-arp
no ip route-cache
no cdp enable
bridge-group 237
--More-- bridge-group 237 subscriber-loop-control
bridge-group 237 block-unknown-source
no bridge-group 237 source-learning
no bridge-group 237 unicast-flooding
bridge-group 237 spanning-disabled
interface FastEthernet0.238
encapsulation dot1Q 238 native
no ip redirects
no ip unreachables
no ip proxy-arp
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 10.238.1.100 255.255.0.0
no ip redirects
no ip unreachables
no ip proxy-arp
no ip route-cache
--More-- ip default-gateway 10.238.1.10
no ip http server
ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
control-plane
bridge 1 route ip
line con 0
privilege level 15
logging synchronous
line vty 0 4
login local
end
I have tried upgrading the WLAN NIC drivers to the latest version (3.5 I believe) but it does not help. If I run the troubleshooting task of the Aironet Desktop Utility is sasys that the Authentication tests failed, even though the status shows me as "Authenticated". Perhaps there is something in the above config that I am missing.
Any help would be greatly appreciated.
JoeCheck the hardware version of your AP radio(S).
Earlier versions (ending in "20") do not support AES (used for WPA2 / 802.11i).
You should have at least a "Radio AIR-MP31G " for your 802.11G and "Radio AIR-RM21A" for your 802.11a radio.
THe (probably) easiest way to check this is the Web GUI ... go to INterfaces, select each band, then the "Detailed Status" tab.
If your radios are older than this, the CLI and GUI will accept your configuration for WPA2/802.11i, but will not operate in that mode (and usually fail).
Either radio is independently upgradeable for ~US$100.00 through someplace like www.cdw.com.
Good Luck
Scott -
How to change default admin password on Cisco Aironet 1040
How do I change the default username and password on the Cisco Aironet 1040. There is a default set and I want to change that to secure the device. I've checked the manual and can't seem to find the directions. Any ideas?
Hi Brian,
If this AP is already registered with a WLC then you can change it via WLC.
In WLC GUI, go to Wireless -> Select the AP -> Credential -> Override Global Credential-> Update username/pw/enable pw
In WLC CLI, you can configure it like this. If it is for all APs, then select all, otherwise AP name.
(WLC3) >config ap mgmtuser add username admin password Cisco123 secret Cisco123 ?
all Applies the configuration to every AP that does not have a specific user name.
Enter the name of the Cisco AP.
(WLC3) >config ap mgmtuser add username password secret
(WLC3) >save config
Are you sure you want to save? (y/n) y
If it is Autonomous AP you can configure using the "username xxxx password xxx" IOS command
HTH
Rasika
*** Pls rate all useful responses ****
Maybe you are looking for
-
I've been noticing that any site I go to that opens content in a new window with "javascript:void(null);" will be ignored by Safari 3.1. The links work in Firefox and used to work in Safari as well. Any suggestions?
-
Refreshing JTable remotely or in another computer
I have search the forums but i could not find the appropriate answer for my problem. I created a jtable with two buttons to add and delete row. This jtable and the mysql table which is the source of the data in the jtable, can be accessed by any comp
-
IWeb says 'offline' when trying ftp publishing
I have tried to Publish individual sites using ftp in iWeb but each time I click on Test Connection I get an error message "You are offline. Please check your internet connection and try again" . Of course I am not offline since Safari, Mail , and Tr
-
Multiple deadlines in one activity - requested end deadline
Hi, I have a requiredment I need to have 2 deadline notifications on one activity. if the task is not finished (requested end) in 5 days then an email should be sent to one dept. (one person) after 3 days of sending the first escallation email if the
-
hi experts can any one explain me about symbolic accounts, and the difference between symbolic accounts and g/l accounts.how to post payroll results to fico