Configuring Cisco Aironet 1140 for Radius and setting up a Radius server

guys i need some help setting up my Radius to work with cisco aironet 1140, i am new at this however i was tasked with setting up a Radius server and setting our AP with WPA2- enterprise so users can log into our AP using AD credentials.
When i try to setup on the AP a new SSID i do not see the option for WPA2- enterprise?

Here are other links with examples:
https://supportforums.cisco.com/thread/331581
http://targetcisco.blogspot.com/2011/03/cisco-autonomous-access-point.html
http://downloads.avaya.com/css/P8/documents/100041614
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Similar Messages

Cisco Aironet 1140: 3 of our 4 are always hanging

Our office has 4 Cisco Aironet 1140 access points mounted on the ceiling. They are all powered via PoE. Every few days 3 of the 4 access points hang and have to be rebooted. When they hang I am not able to connect to their web interface to check the logs. The fourth, for some reason, always seems to stay alive.
I checked the configuration for all AP's and "Hot Standby" is disabled
They are all using static IP addresses. I've tried 2 different banks of static IP addresses and 3 of 4 still hange so I don't think this is an IP conflict
I have saved the configurations and compared them and they are all identical, where possible.
They all have software version: 12.4(21a)JA1
They all have bootloader version: 12.4(23c)JA1
I have tried to download the latest software/firmware, but unfortunately I do not have a valid service contract in place with Cisco and therefore can't download the latest version. All of our CISCO hardware was purchased from Amazon resellers and they can't seem to help me with this. I have also tried to contact Cisco and they can't seem to help either. If anyone has a suggestion on how I can get a valid service contract that information would also be very helpful!!!
Does anyone have any ideas why 3 of our 4 access points would hang? When they hang, I can't login to the web interface and the logs seem to reset when I reset each access point. I have also set up an rsyslog server and I don't see a log entry that would indicate a problem.
Any ideas?
Thank you

Here is the config for one of the AP's that keeps hanging:
! Last configuration change at 09:18:05 -1000 Mon Jan 30 2012 by admin
! NVRAM config last updated at 09:18:05 -1000 Mon Jan 30 2012 by admin
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname XXX2
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
clock timezone -1000 -10
ip name-server 8.8.8.8
ip name-server 8.8.4.4
dot11 syslog
dot11 ssid XXX2
   authentication open
   authentication key-management wpa version 2
   guest-mode
   wpa-psk ascii 7 01234567890123456789012
username admin privilege 15 password 7 01234567890123456789012
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid XXX2
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.100.252 255.255.255.0
no ip route-cache
ip default-gateway 192.168.100.1
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
snmp-server community MyCommunity RO
bridge 1 route ip
line con 0
line vty 0 4
sntp server 192.43.244.18
sntp broadcast client
end

How to load a boot image to cisco aironet 1140 series after missing boot image

Hi all,
I need a solution for this. When i switch my cisco aironet 1140 , it s blinking with red light .and gives a message "no boot image to load".
When i tried next time, by pressing escape it shows this message that i have mentioned below.
ap:
ap:
using eeprom values
WRDTR,CLKTR: 0x83000800 0x40000000
RQDC ,RFDC : 0x80000035 0x00000208
using ÿÿÿÿ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0x40000000
RQDC, RFDC : 0x80000035, 0x00000208
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
PCIE1 port 1 not initialized
PCIEx: initialization done
flashfs[0]: 1 files, 1 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 1536
flashfs[0]: Bytes available: 32383488
flashfs[0]: flashfs fsck took 16 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 28:94:0f:d6:c8:62
Ethernet speed is 100 Mb - FULL duplex
The system is unable to boot automatically because there
are no bootable files.
C1140 Boot Loader (C1140-BOOT-M) Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Tue 18-Oct-11 14:51 by prod_rel_team
ap:
So , now my question is how to load the boot image ? From where will we get this ? OR
I m also having another Cisco aironet 1140 , Can i get bootimage from that . Kindly let me know the solution from genius ?

Take a look at this link as it should have the info you need
https://supportforums.cisco.com/docs/DOC-14636
Sent from Cisco Technical Support iPhone App

Configuring Netgear FVS318 VPN for iPhone and Mac OS X clients.

Hi,
I am trying to configure the FVS318 VPN for iPhone and Mac clients to connect to. I have been able to set it up that all hard wired and wireless connections with in the network to connect seemlessly, but when it comes to VPN I am not able to get any connection from outside the network. I have set all the usernames, passwords and shared secrets multiple times and I am unable to connect even after reseting it. Any help setting this would be great.
Thanks

Are you using your external IP address to set this up? This works while on the network, as in at the office but not from any connection outside? What IP scheme are you using on the Netgear? If you are using something like 192.168.1.1 and starbucks uses the same scheme it wont work. Try setting your Netgear to something like 192.168.33.1

I received a new IMac for Christmas and set up a new .me account and I'm using this on my IMac and IPhone4S. how do I transfer my music from my old Windows iTunes account to my new Mac account?

I received a new IMac for Christmas and set up a new .me account and I'm using this on my IMac and IPhone4S. how do I transfer my music from my old Windows iTunes account to my new Mac account?

You can red this article about transfering your tunes - http://www.myfirstmac.com/index.php/mac/articles/how-do-i-move-my-itunes-library -from-pc-to-mac-and-keep-my-settings-intact
MJ

Can't find autonomous image to Cisco Aironet 1140

Can anyone gives a link?
-JeIlMa

Here you go:
http://tools.cisco.com/support/downloads/go/PlatformList.x?sftType=IOS+Software&mdfid=282439881&treeName=Wireless&mdfLevel=Model&url=null&modelName=Cisco+Aironet+1140+Access+Point&isPlatform=N&treeMdfId=278875243&modifmdfid=null&imname=&hybrid=Y&imst=N

Setting up Cisco Aironet 1250 for home use

Hey everyone,
I'm rather new to the whole Enterprise Router lines. I've set up countless networks with Linksys routers in the past. However, this Aironet is giving me more trouble than I'd want it to. I was wondering if anyone could help. I've assigned it an IP Address and accessed that In-Browser interface and set up an SSID and activated the two extensions. I've been able to connect to the router with my computer and access the internet without restriction. However, when I attempt to connect a second PC or Laptop to the network, it won't allow network access to the second device. I've been stuck there forever. Is there any specific setup method I need to use to make sure more than one workstation/device? I want to use this router for home use, I often use laptops and move around the house a lot, so the advantage of better connection signal and speed is well worth it. Any help is highly apprieciated. If you need more information, don't hesitate to contact me.

Sorry for my late reply. Here is the config:
It wasn't connected to anything. This was a raw pull from a fresh cold boot.
IOS Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 150 files, 7 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 6406144
flashfs[0]: Bytes available: 25462784
flashfs[0]: flashfs fsck took 16 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: 54:75:d0:dd:b5:12
Loading "flash:/c1250-k9w7-mx.124-10b.JDA3/c1250-k9w7-mx.124-10b.JDA3"...##################################################################################################################################################################################################################
File "flash:/c1250-k9w7-mx.124-10b.JDA3/c1250-k9w7-mx.124-10b.JDA3" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Sun 07-Jun-09 03:50 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x01000000
Initializing flashfs...
flashfs[1]: 150 files, 7 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 31868928
flashfs[1]: Bytes used: 6406144
flashfs[1]: Bytes available: 25462784
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Warning: the compile-time code checksum does not appear to be present.
Radio 1 A600 8000 0 0 A8030000 30
Radio 1 A600 8000 0 0 B8030000 13
tx_paks 1293
tx_paks 646
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html you require further assistance please contact us by sending email to
[email protected]. AIR-AP1252AG-A-K9    (PowerPC 8349) processor (revision C0) with 49142K/16384K bytes of memory.
Processor board ID FTX1423902R
PowerPC 8349 CPU at 533Mhz, revision number 0x0031
Last reset from power-on
1 Gigabit Ethernet interface
2 802.11 Radio(s)
If
cisco
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 54:75:D0:DD:B5:12
Part Number                          : 73-10425-06
PCA Assembly Number                  : 800-27630-06
PCA Revision Number                  : B0
PCB Serial Number                    : FOC142025F4
Top Assembly Part Number             : 800-29039-03
Top Assembly Serial Number           : FTX1423902R
Top Revision Number                  : A0
Product/Model Number                 : AIR-AP1252AG-A-K9
Press RETURN to get started!
*Mar 1 00:00:06.211: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.039: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:07.543: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:09.587: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 00:00:09.591: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Sun 07-Jun-09 03:50 by prod_rel_team
*Mar 1 00:00:09.591: %SNMP-5-COLDSTART: SNMP agent on host Cisco1250 is undergoing a cold start
*Mar 1 01:37:52.027: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 01:37:52.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 01:37:52.707: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 01:37:53.467: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 01:37:53.467: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 01:37:53.847: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 01:37:54.467: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 01:37:54.695: %CDP_PD-4-POWER_OK: Full power - INJECTOR_DETECTED inline power source
*Mar 1 01:37:54.703: %DOT11-4-NO_HT: Interface Dot11Radio1, Mcs rates disabled on vlan 0 due to not using AES encryption or
*Mar 1 01:37:58.303: %DOT11-6-FREQ_USED: Interface Dot11Radio1, frequency 5180 selected
*Mar 1 01:37:58.307: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 01:37:58.307: %DOT11-4-NO_HT: Interface Dot11Radio0, Mcs rates disabled on vlan 0 due to not using AES encryption or
*Mar 1 01:37:58.311: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0, Scanning frequencies for 13 seconds
*Mar 1 01:37:59.307: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 01:38:00.307: %LINK-3-UPDOWN: Interface BVI1, changed state to down
*Mar 1 01:38:02.931: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Mar 1 01:38:11.919: %DOT11-6-FREQ_USED: Interface Dot11Radio0, frequency 2462 selected
*Mar 1 01:38:11.923: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 01:38:12.923: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
Cisco1250>enable
Password:
Cisco1250#show running-config
Building configuration...
Current configuration : 1717 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname Cisco1250
enable secret 5 $1$jDeQ$cFdx0aHAd8wj8tk6CCmXq/
no aaa new-model
dot11 ssid Home Network
   authentication open
   guest-mode
power inline negotiation prestandard source
username Cisco password 7 05280F1C2243
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption key 1 size 128bit 7 23D0220D02AE7FA723492AA01E34 transmit-key
encryption mode wep mandatory
ssid Home Network
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption key 1 size 128bit 7 0B4935657C801B3620154AB56630 transmit-key
encryption mode wep mandatory
ssid Home Network
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.0.1 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
snmp-server community Community RW
bridge 1 route ip
line con 0
line vty 0 4
login local
end
They way I connect it in the network is as follows:
BrightHouse Networks ISP Modem --> Cisco Aironet 1252 --> Incoming connections from computers and laptops.
Any ideas?

Cisco Aironet 1140 Issues (Dropping clients, 5GHz issue, AP Switching)

Greetings,
We've been having issues for a while with these Aironet 1140's. We have two of them in the office and the issue is similar to the first issue displayed in this post:
https://supportforums.cisco.com/docs/DOC-26228
The only difference is that I can't do this since we don't use a controller.
We're using Mac clients on Lion/Mt. Lion. We have no issues connecting to the access points, but occassionally the user will drop off one of the AP's(Access Point 2). Recently I changed the setup from TKIP/WPA to AES-CCM/WPA to get the PHY address to 802.11N instead of 802.11G. I got the speeds working fine, but I suppose this caused an issue of people dropping off at different times. I noticed if I remove the SSID from the preferred list and reconnect it goes from WPA to WPA2. Not sure if this is relevant information, just trying to list what I can to resolve this issue. I haven't had any reported issues with the other Access Point(Access Point 1).
Another issue we have is getting the radio to work on 5GHz for Access Point 1. It seems when a user is connected to the 5GHz signal, it will not load any web pages. Can ping out just fine, and ping internally as well. I've checked to see if the client is getting an IP address, and it is. It also has DNS set to 8.8.8.8 and another DNS IP we use. The other Access Point seems to work just fine with 5GHz enabled. Both work with 2.4GHz with no issues at all.
Lastly, clients are not switching Access Points to the strongest signal. I've tried this test with 5+ machines running different OS's from Snow Leopard to Mt. Lion. The client will not switch over passively, the Laptop must be closed and reopened to re-establish the connection to grab the closest signal. This isn't a huge issue, but it's something I'd like to get fixed. This could have been an ongoing issue before I switched the AP's to AES-CCM, but I've only noticed it after the fact.
If there's any additional information needed that could help resolve these issues, let me know.
Thanks!

The wireless clients/devices decides which WAPs to join. It's not a "Cisco thing". It's the standard.
That's what I figured, it's just an issue we have been having lately and trying to rule out the possibility it might be an Access Point issue.
Did you enable WPA and WPA2??? Apple does not like to "choose". You have to either use WPA OR WPA2.
Actually, yes I should have included my steps of trying to resolve the issue. For some reason, the SSID would not appear in the listing of SSID's so I removed the preferred connection, which was WPA, and manually added it to be WPA2 Personal on the client. Still saw some issues with a few users, others seem to have rectified or they're not telling me.
I checked the event logs on the device and saw this:
Packet to client e0f8.4735.c16e reached max retries, removing the client
After some research, it was recommended to raise the packet retry value to 128. I haven't received any complaints from the 3 people that usually complain about dropped wifi yet, but it's still too soon to say.
The only thing I can think of is the signal strength. Disable the 2.4 Ghz and see what signal strength you are getting with the 5.0 Ghz.
It should not be signal strength since I am about 10 feet away on my test machine which has the issue as well as any other clients in any distance long enough to grab the connection. I will try turning off 2.4 when there's nobody in the office tomorrow in the morning to see if that actually works. I would like to have it dual band though since we're not all at 5GHz here. With this issue, I was actually fearing that there just may be an issue with the 5GHz radio hardware. We also have an extra 1140 laying around I used for testing; the 5GHz radio worked with identical settings to the one not working.
Thanks for the reply! I will take a look at what you suggested a little further and keep this updated if increasing the packet retry value actually rectified the problem just in case someone else has the same issue.

Multiple Cisco Aironet 1131AG access points and same SSID?

We have multiple Cisco Aironet 1131AG devices, all wired on one Cisco L2 switch(2560) who is connected to L3 switch (3550). We assigned one VLAN for access point in L3 switch who acts as vtp server (L2 switch is vtp client). All ap's will have static ip address and all will have same SSID and no security and they will be using multiple channels (ex. 1,6,11). They will operate in 3 floor building for roaming wireless client. We won't using any wireless controller.
So my question is this: How to configure APs-all the same with different ip's, can we use L3 switch to create dhcp server for access points VLAN (pool for clients, and the rest for static ip for ap's)? Can one of the ap's be WDS and in the same time local radius server with users without Cisco Secure ACS or similar controller or I didn't understand this quite well :-). I followed guide http://www.cisco.com/en/US/docs/wireless/access_point/12.3_2_JA/configuration/guide/s32roamg.html for WDS where the part abou Cisco ACS is a problem, so I can use same ap as Local Authenticator as in guide http://www.cisco.com/en/US/docs/wireless/access_point/12.3_4_JA/configuration/guide/s34local.html#wp1035723.
Many thanks...

Well, just so you know, WDS and local RADIUS authentication is only needed if you're using authentication on your wireless connection. You say you're not planning to use security, so this isn't necessary. However, I'd highly recommend at least using a simple WPA2-PSK to lock down your connection, otherwise you might end up giving free Internet access at best, and at worst you might be giving access to company PCs and servers. If you want to further use an 802.1x or WPA authentication method, then yes, you can use an AP as a RADIUS server and WDS to improve authenticated roaming, but this is far more limited than using a Cisco ACS.
As for your other questions, yes, your APs can all be configured the same except for at least three parameters: IP address, channel, and hostname. Configure your static IP addresses on the AP's BVI1 interface. Don't place it on the Radio or Ethernet interfaces, because if either of these interfaces goes down you'll lose the ability to configure the AP, so it's best to use the BVI1 interface.
And yes, configuring a DHCP scope for your clients on your L3 switch is a good design, or you could also use your DHCP server on a different subnet by using the ip helper-address command on the L3 interface. I hope this helps! Let me know if you need help configuring any of this.
Merry Christmas!
Jeff

Aironet 1140 AP's and DHCP

We have 6 aironet 1140's throughout the office I have them all configed as one ssid but I would like the DHCP to come from our Windows server. Right now I have set them up with ip dhcp pools. So what is the secret to get them to send dhcp requests to the Windows server?
Thanks

Nope...
All you have to do is configure ip helpder address on L3 device and remove the dhcp pool configuration from AP's. This will ensure that devices pick ip from your wondws dhcp scope.
Hope that helps.
Regards
Najaf
Please rate when applicable or helpful !!!

Cisco Aironet 1140 Association

All,
Quick question about the association web interface tab on a 1140. I have noticed that the Device Type shows as "unknown" and the Name shows as "NONE." Anyone have a clue as to why? Thanks for any help!
Dave

Any resolution on this?
We have about 20 Cisco Aironet APs and they all show the same, Device type unknown, Name NONE

Bug? Cisco Jabber Video for TelePresence and spanish keyboard

Hello everybody,
because of a customer request I checked Jabber Video with spanish keyboard configured (traditional sort) an figured out, that with this configuration the Jabber Client (tested with 4.2, 4.6 and 4.8.8) doesn't accept the pound key when it is pressed on the keyboard. In Word for example the pound key works as expected. At the moment I told the customer to use the "onboard" keyboard in the Jabber Video client, but I think it is a bug (don't know if it's a bug in Jabber Video or Windows 7). Has anyone experienced the same? Maybe this will be fixed in future?
Regards, Daniel

You can have both "free" and "enterprise" versions installed on a Mac.
If you already have "enterprise" version installed on a PC, and you install the "free" version, the registry settings will be changed and server setting locked to
https://sjc1-movi-pr-bootproxy-vip.ciscojabbervideo.com/endpoint/configuration
when you install the "free" version, so ,no, you can't have both versions installed on the same PC.
You can change the registry settings so it's not locked to the Cisco server, but then you might as well just have the "enterprise" version installed and just edit the internal server settings to use the above URL if you want to make it behave as the "free" version.
There's no difference, clientwise, between the two, the server settings determines which server it will register with, and provisioning settings will change accordingly.
/jens

Cisco aironet 1310G non_native vlan and dhcp

hi evrybody
i have problem with my cisco aironet 1310G
non-native vlan can not get(dynamicly)ip address from cisco aironet 1310G
this is all my configuration please can someone help me
ip dhcp excluded-address 20.20.20.20
ip dhcp excluded-address 20.0.0.0
ip dhcp excluded-address 30.0.0.0
ip dhcp excluded-address 30.30.30.30
ip dhcp excluded-address 10.0.0.0
ip dhcp excluded-address 10.0.0.10
ip dhcp excluded-address 10.1.0.0
ip dhcp excluded-address 10.1.0.10
ip dhcp pool d01
network 10.0.0.0 255.255.255.0
default-router 10.0.0.10
ip dhcp pool d02
network 20.0.0.0 255.255.255.0
default-router 20.20.20.20
ip dhcp pool d03
network 30.0.0.0 255.255.255.0
default-router 30.30.30.30
no aaa new-model
dot11 ssid vlan01
vlan 1
authentication open
dot11 ssid vlan02
vlan 2
authentication open
dot11 ssid vlan3
vlan 3
authentication open
username cisco password xxx
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
broadcast-key vlan 2 change 100
broadcast-key vlan 3 change 100
ssid vlan01
ssid vlan02
ssid vlan3
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root access-point
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
interface Dot11Radio0.3
encapsulation dot1Q 3
no ip route-cache
bridge-group 3
bridge-group 3 subscriber-loop-control
bridge-group 3 block-unknown-source
no bridge-group 3 source-learning
no bridge-group 3 unicast-flooding
bridge-group 3 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
hold-queue 80 in
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
no bridge-group 2 source-learning
bridge-group 2 spanning-disabled
interface FastEthernet0.3
encapsulation dot1Q 3
no ip route-cache
bridge-group 3
no bridge-group 3 source-learning
bridge-group 3 spanning-disabled
interface BVI1
ip address 10.0.0.10 255.255.255.0
no ip route-cache
interface BVI2
ip address 20.20.20.20 255.255.255.0
no ip route-cache
interface BVI3
ip address 30.30.30.30 255.255.255.0
no ip route-cache
control-plane
bridge 1 priority 9000
bridge 1 protocol ieee
bridge 1 route ip
bridge 2 priority 10000
bridge 2 protocol ieee
bridge 3 priority 3100
bridge 3 protocol ieee
line con 0
line vty 0 4
login local
end

hi friend
i did what you sugested but it is styl not working so plz find below the show run and debug ip dhcp server in ordr to help us thanks for all your suport
ip subnet-zero
ip dhcp excluded-address 20.0.0.20
ip dhcp excluded-address 30.0.0.30
ip dhcp excluded-address 10.0.0.10
ip dhcp pool d01
network 10.0.0.0 255.255.255.0
default-router 10.0.0.10
ip dhcp pool d02
network 20.0.0.0 255.255.255.0
default-router 20.0.0.20
ip dhcp pool d03
network 30.0.0.0 255.255.255.0
default-router 30.0.0.30
aaa new-model
dot11 ssid vlan01
vlan 1
authentication open
guest-mode
dot11 ssid vlan02
vlan 2
authentication open
dot11 ssid vlan03
vlan 3
authentication open
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
broadcast-key vlan 2 change 100
broadcast-key vlan 3 change 100
ssid vlan01
ssid vlan02
ssid vlan03
station-role root access-point
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
interface Dot11Radio0.3
encapsulation dot1Q 3
no ip route-cache
bridge-group 3
bridge-group 3 subscriber-loop-control
bridge-group 3 block-unknown-source
no bridge-group 3 source-learning
no bridge-group 3 unicast-flooding
bridge-group 3 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
hold-queue 80 in
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
no bridge-group 2 source-learning
bridge-group 2 spanning-disabled
interface FastEthernet0.3
encapsulation dot1Q 3
no ip route-cache
bridge-group 3
no bridge-group 3 source-learning
bridge-group 3 spanning-disabled
interface BVI1
ip address 10.0.0.10 255.255.255.0
no ip route-cache
interface BVI2
ip address 20.0.0.20 255.255.255.0
no ip route-cache
interface BVI3
ip address 30.0.0.30 255.255.255.0
ip helper-address 30.0.0.0
no ip route-cache
and debug ip dhcp server {events | packets | linkage}
*Mar 1 01:06:37.054: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating
Station 0011.a304.2b65 Reason: Sending station has left the BSS
*Mar 1 01:06:40.140: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 0011.a304
.2b65 Associated KEY_MGMT[NONE]

Configuring CISCO AIRONET AP

Hello;
how to configure the IP Adress of CISCO AIRONET 1600i AP to access It through the Web browser and configure It?
we tried to assign a static IP using CLI so we downloaded Tera Term and tried to connect It using the DB Cable. The following message shows up:
*Mar 1 01:41:43.674: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
we tried to execute 'Enable' command and It works then we tried to execute 'config t' command but failed (the other commands do not work too):
APf07f.06f0.93b5#config t
^ % Invalid input detected at '^' marker.
I connected the Aironet AP to a Router which has 192.168.1.1 as a default IP Adress and thats what shows up on the terminal:
Translating "CISCO-CAPWAP-CONTROLLER.Home"...domain server (192.168.1.1)
*Mar 1 00:34:05.251: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:34:05.255: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.Home
Not in Bound state.
*Mar 1 00:34:50.754: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:34:53.766: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
*Mar 1 00:34:53.830: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.1.5, mask 255.255.255.0, hostname APf07f.06f0.93b5

Hi
By default these AP comes with lightweight image & require a WLC to manage it.(unless you specifically order this AP with autonomous image)
If you want to convert it autonomous (to use without a WLC) then you have to load an autonomous image to it. You should have an image like this (ap1g2-k9w7-tar.153-3.JAB.tar) to begin with (you may require a valid maintenance contract to download this from cisco web site)
Then you can follow one of the methods to convert it to a autonomous AP
1. http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/
2. http://mrncciew.com/2013/12/13/ap-conversion-using-mode-button/
HTH
Rasika

"problem reading configuration" Bug in Admin for Graphite and Snow

Background: Bought a used "graphite" (M5757 SN PW9495EYH93) for a friend with only dial-up access. Downloaded Airport Admin for Graphite and Snow. System seemed to be operating fine - I could see it on WiFi and even connect. Of course I was missing some passwords, so I needed to get it back to default settings by doing a hard reset-"perform a local reload". Support article HT2439 provided instructions: I plugged in a wired connection.
But "Auto" address selection didn't seem to work - I kept getting "problem reading configuration" messages.
So I tried "Manual" for entering IP address and password.
OOPS! When selecting "manual" for setting the IP address, the IP address triplets entered were reversed when saved in the device. Or at least they display reversed in AirPort Admin, while other nearby AirPort addresses display correctly.
For instance, when I set the device to the Apple default address of 192.42.249.13, the address displayed in AirPort Admin was 13.249.42.192. This was reliably repeatable, and worked around by entering the desired triplets in reverse order. Once I inverted the triplets and got the IP address I expected into the AirPort, configuration proceeded smoothly.
This bug can lead to frustration finding and reconfiguring AirPort devices, communicating over ethernet (since of course the network address and subnet masks work perfectly, but not as expected) and displaying/changing configurations. I didn't spend more time investigating the boundaries of the problem after finding the work-around and getting this particular AirPort working, but the problem might be the cause of some of the other configuration issues that seem to crop up regularly.

Hello Dudlington. Welcome to the Apple Discussions!
The "Airport Admin Utility for Graphite and Snow" seems to be at version 4.2.5 for OS X and was released in April 2008, yet only supports the "dual ethernet" versions.
Not to worry, the "Dual Ethernet" and "Snow" actually refer to the same model. The 802.11b Snow is the predecessor to the 802.11b/g AirPort Extreme Base Station (AEBS) and followed the "Graphite."

Configuring Cisco Aironet 1140 for Radius and setting up a Radius server

Similar Messages

Maybe you are looking for