Configuring FAX on ATA 186 with CME 3.4

Hi,
I have an ATA 186 connected to my network, I have configured CME for auto assign extensions & I got an extension as well, when I connect analog phone it works fine but when I connect FAX Machine I cannot send & recieve fax. Do I need to change any configurations in ATA???? Please check the screen shot attached

Try this link for more information on configuraing FAX on ATA
http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_configuration_example09186a00800d698e.shtml

Similar Messages

  • Problem to register ATA 186 with CME 7.0

    Hello,
    I have to two ATA connected into switch that are connected with Cisco 2851.
    The first ATA was connected in the past and it works well, now I need to connect another ATA  but I don't be able to register in CME.
    Both ATA have the same version of firmware, and got ip by the dhcp.
    I've checked the ports in switch where are connected the ata's and have the same configuration.
    To register the new ATA I go into CME portal and when I try to add a new phone I receive a message that say "no new phone to add".
    Please help me to fix it
    Thanks
    Regards

    Hello,
    thanks for the answers.
    I solved the new ATA was registred automaticaly in cme with a randon telephone number, for this reason I wasn't able to find it.
    With the command show ephone register I checked all the phones registered with the number and I finded the new ata.
    Thanks for your help,
    Regards

  • ATA-186 with overhead paging systems

    Since the ATA-186 supplies 600 Ohms, would I need a seperate device such as a Bogen TAM-B to supplie the audio for overhead paging, or could I just use the ATA-186?

    ATA-186 can be used as an audio source.

  • Ata 186 with Polycom MGC 100

    I'm trying to setup an audio conference on a Polycom MGC100 with a Cisco Ata186. I can dial out to the Ata using the IP address and the Ata will answer but it disconnectes after 30 seconds. Has anyone else tried this and if so what were your results? Thanks.

    I have the same problem as well with CM 6, however my calls last about 30 minutes then disconnect.
    Has anyone found a solution?

  • ATA 186 with External Bogen Night Ringer

    Using Call Manager, I am using an ATA with and External Bogen Night Ringer. It works when I call the ATA extension and the Speakers Ring out but when I call forward a ip phone to the ATA DN the speakers do not output anything. My goal is to call forward the main DN of the receptionist to the ATA hooked up to the Bogen TPU-100B paging unit that has the night ringer functionality. I thought it might be some sort of gateway issue but the call forward does not work from IP Phone Calling another IP Phone that is call forwarded to the ATA with the Night Ringer. Does anyone have any ideas.

    http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=IP%20Communications%20and%20Video&topic=Video%20over%20IP&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.ee944f1/3
    I think the ring voltage is not suffecient enough from the FXO being passed to the ATA, I think I need to viking RG-10A to sit inline and boost increase power on the line. The Bogen requires 90V.

  • ATA 186 for FAX With CME

    Hi,
    I have ATA 186 connected to my network when i connect a phone it works but when I connected fax machine i cannot recieve or send faxes...do I need to do any configurations in ATA...please check the attachment..

    you'll need dial peer(s), on your CME router, that enable FAX passthrough as well as a few other pieces.
    please see the following link for Config/Troubleshooting ATA-186 with FAX:
    http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_configuration_example09186a00800d698e.shtml#task2

  • ATA 186 - Faxing with sccp on CCME

    Is there any specific config required to get a fax working with an ATA 186 with sccp, both in the ATA settings and ccme config ?
    Any useful links or example configs would be a great help
    Thanks in advance

    Hey Mark,
    Here are some good ATA - Fax related docs;
    Field Notice: Fax Passthrough Limitations on ATA 186
    http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_field_notice09186a0080094af7.shtml
    Configuring the Cisco ATA for SCCP
    http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_administration_guide_chapter09186a00801e0e0c.html
    Configuring and Debugging Fax Services
    http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_administration_guide_chapter09186a00801e0dff.html
    Hope this helps!
    Rob

  • Cisco ATA 186 configuration to connect FAX machine

    Dear All,
    Please could you give me the procedures and configuration to install and configure the cisco ATA 186 for the FAX in the IPT network.The network contains the following
    1.Callmager4.1.3
    2.MCS7825
    3.Voicegateway 1760USING h.323 SING.pROTOCOL
    4.cp 7912G, 7940G
    I want to know the switch configuration to connect the ATA uplink to the switch.
    Thanks
    swamy

    Simply follow this guide:
    http://www.cisco.com/univercd/cc/td/doc/product/voice/ata/ataadmn/sccp3_0/sccpaapd.htm
    HTH, please rate all posts!
    Chris

  • Problem with Fax and ATA

    Hi,
    i do not have problem to send Fax to the PSTN, but when I try to receive a fax on the fax machine in port1 of the ATA, the machine never give fax signal.

    Hi Leonardo,
    Have a look at the following;
    Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide (SCCP) (2.15.ms, Rev B0)
    Configuring and Debugging Fax Services
    http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_administration_guide_chapter09186a00800c4d1e.html#1016012
    Configuring and Troubleshooting the Cisco ATA 186 with Fax
    http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_configuration_example09186a00800d698e.shtml
    Configure Fax Detection Method on the Cisco ATA 186
    Use a web browser and go to http:///dev (for example, http://172.16.104.117/dev) in order to configure the Cisco ATA 186 using the web interface.
    You must configure these parameters in order to configure the Cisco ATA 186.
    Audio Mode
    bit 2 (18)=0 Enable detection of FAX CED (answer) tone and switch to FAX mode for the rest of the call if the tone is detected.
    Hope this helps!
    Rob

  • Troubleshooting an ATA 186

    How can I tell what digits are being passed from a phone plugged into an ATA 186?
    We have an ATA 186 with a credit card machine plugged into it that is failing to place calls. When I monitor the call with a butt set I hear dial tone, then 1 digit being dialed and then an error from callmanager basically telling me to check the number. The call never gets past that first digit. If I use a butt set to place a call everything works fine. I'm concerned the digit being passed is not the access code of 8, and I want to verify that. I have also included the 9001.log from the prsrev.exe I just don't know how to read it.

    Hi,
    It look to me like the ATA isn't configured properly in CCM?
    There's a lot of messages in the log stating "RegRej[1]:Error: DB Config", which I think means the device isn't registering properly.
    Have you checked the ports are configured properly?
    Here's a troubleshooting guide which may also help:
    http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_configuration_example09186a0080094adf.shtml
    Please rate if useful...

  • ATA 186 needs assistance configuring to work with SIP

    Hello. Just got ATA 186. I would like to use it as SIP FXS. I already have FXO with the POTS plugged in. I don't want o use the gateway or the gatekeeper. I would like to configure it to be IP dialing. II am running SIP image ATA030201SIP050616A.zup. Any help is greatly appreciated.
    George

    Hello, already replied in another thread, please do not open duplicates.

  • ATA 186 Issue to send faxes

    Hi,
    I have an issue with ATA 186 to send faxes. I have tried many things, but the fax sending  is unsuccessful. I am not a VoIP expert, so it is pretty hard to me to identify the difference between some commands. This is the topology of the network:
    Fax Machine --- ATA ---- CCM ---- VoIPGW --- E1(PSTN)
    I have the following values in ATA:
    AudioMode: 0x00120012
    ConnectMode: 0x00008400
    This is the dial-peer configured to that Fax:
    dial-peer voice 1010 voip
    call-block translation-profile incoming 110
    call-block disconnect-cause incoming call-reject
    preference 1
    destination-pattern 1044
    voice-class h323 1
    session target ipv4:10.15.190.4
    dtmf-relay cisco-rtp h245-signal h245-alphanumeric
    codec g711ulaw
    fax rate disable
    fax protocol pass-through g711ulaw
    no vad
    Aditionaly I had the following lines in VoIPGW:
    ccm-manager fax protocol cisco
    mgcp
    mgcp fax t38 ecm
    Recently I changed to:
    no ccm-manager fax protocol cisco
    mgcp
    mgcp fax t38 inhibit
    Not sure if I missing something, in the other hand I would like to know which is the different between  fax protocol pass-through g711ulaw and modem passthrough nse codec g711ulaw
    Thanks for your comments....

    Hello,
    There is one relly important detail on this matter, is the fax machine a super G3 fax machine? this is because as you mention there are some limitation for the ATAs to work with fax machines and modems, this is because the device was not designed for this purpose.}
    In the follow link you could find some information about the ATA configuration for faxing:
    http://www.cisco.com/en/US/partner/products/hw/gatecont/ps514/products_qanda_item09186a00800946e1.shtml
    Another important detail is check if your gateway supports the type of faxing that you are trying to do
    http://www.cisco.com/en/US/partner/tech/tk652/tk777/technologies_tech_note09186a0080159cf3.shtml
    Finally this are the configuration steps for you voice gaway:
    http://www.cisco.com/en/US/partner/docs/ios/12_3/vvf_c/cisco_ios_fax_services_over_ip_application_guide/pt.html
    HTH
    <-------------------->
    Walter    Solano
    CCNA Voice
    UCCX Specialis

  • ATA-186 can be registered with CUCM v10.5

    Hello guys ;
                          Please confirm me that ATA-186 can work with CUCM v10.5 ? .
    Regards;
    Shib

    Loaded the latest firmware into CM, then manually on ATA firmware using this process as CM didn't change it:
    http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cata/186_188/3_0/english/administration/guide/sccp/sccp3_0/sccpaapc.html#wp1011450
    I followed this link from another post regarding ASA not registering for an older issue.
    http://www.cisco.com/en/US/docs/voice_ip_comm/cata/186_188/3_0/english/administration/guide/sccp/sccpaape.html#wpxref59054
    Follow the part that mentions setting the SID0 & SID1 to "." no quotes.  I did this and my ATA registered to CM.  Screen caps attached.
    I have a Cisco ATA 186 running on 10.5.1 and it shows to be registered.  I can make calls on it.  Not sure how it will do for faxes.  HTH Please rate.

  • Configuring ATA 186

    We have a single 2610XM Router at central site and all remote 805 Routers.We want to configure ATA 186 at all the sites for VoIP connectivity.Can we configure the Gateway and Gatekeeper on the single 2610XM Router?It has come loaded with h.323 software feature set and has flash of 16MB and DRAM 32MB.
    Pls suggest a solution.

    Yes you can run both Gatekeeper and Gateway functions on the 2610XM router at the same time. You may need to bump your DRAM up in order to run the latest images that support both Gatekeeper and Gateway functionality. For example you could use the following image (c2600-ix-mz.12.3-1a) which is the IP/H323 featureset in the 12.3 release train. The minimum memory requirement for this is 48Megs of DRAM.
    Once you have your gatekeeper configured, you would then configure your ATA's to point to the gatekeeper, and all your remote ATA's will be able to locate and call each other. If your 2610XM is also utilized as the PSTN gateway, then your remote ATA's can call out to the PSTN via the same router.

  • Is it possible to configure an SNMP copmmunity string on an ATA 186 without accessing it via console?

    I am trying to configure a particular SNMP community string on many ATAs for a Cisco 'Know the Network' project. On a Cisco ATA 186, you cannot telnet or SSH to it and the only way to remotely change the parameters are via the web GUI, which doesn't have the SNMP field available.
    Is this possible without getting physical console access to the ATA?

    No.
    An ASA can, as you noted, restrict source and destination IP and port. To do what you are asking, one would need to prevent a string within the payload from being transmitted (or only accept certain strings).
    You should just put the access-list on the destination device(s) restricting what host(s) are allowed snmp rw (as you alluded to). That's a very common implementation straight out of the textbook.

Maybe you are looking for