Configuring Frame-Relay and the Frame-Relay Switch To Participate in WAN Routing
Hey,
My WAN in my voice lab is currently functional between all of my routers HQ, BR1, and BR1 with full-mesh connectivity. I am using my PSTN router for the frame-relay switching as is shown in the attached configs. I have used the connect commands for the PVC routing logic.
connect HQ-BR1 Serial0/3/0 101 Serial0/2/0 201
connect HQ-BR2 Serial0/3/0 102 Serial0/2/1 301
connect BR1-BR2 Serial0/2/0 202 Serial0/2/1 302
My question concerns the possibility of getting the PSTN router to participate in the WAN and the OSPF routing process? The connect command tells how the PVCs are to be connected and pass through the PSTN router. Is there anyway to do it so that a PVC connects to the PSTN router itself?
I would specifically like to create a connection between the HQ and PSTN router over the WAN. If anyone has any insight on this I would really appreciate it.
Thank you.
Hello Adam,
you don't need to do FR switching.
You just need to configure a back to back PVC associated to a p2p subinterface under PSTN router interface se0/3/0 and HQ:se0/1/0. the new PVC can be 103 on both sides
PSTN
interface ser0/3/0.103 point-to-point
ip address 10.1.13.1 255.255.255.0
frame-relay interface-dlci 103
HQ
interface ser0/1/0.103 point-to-point
ip address 10.1.13.1 255.255.255.0
frame-relay interface-dlci 103
note: I was able to do this using the older syntax frame-relay route under interface configuration on frame relay switch. I would expect to work for you too with newer syntax connect.
Hope to help
Giuseppe
Similar Messages
-
Hello,
How to I increase the space between the top of tabs and the frame of the entire window? It was fine until Firefox updated and since it updated it reduced the space. Now the space is too thin which makes it more difficult to move the open window frame around when I need to grab something from Desktop. Image attached.In the image, see how thin the space is right above the tab? It was much wider before Firefox update so if any know how to make it wider again, please let me know. Thank you
''troyable7 [[#question-1058550|said]]''
<blockquote>
Hello,
How to I increase the space between the top of tabs and the frame of the entire window? It was fine until Firefox updated and since it updated it reduced the space. Now the space is too thin which makes it more difficult to move the open window frame around when I need to grab something from Desktop. Image attached.
</blockquote>
In the image, see how thin the space is right above the tab? It was much wider before Firefox update so if any know how to make it wider again, please let me know. Thank you -
Trying to export a video and the frame keeps getting cut
Hello,
I'm trying to export a video and the frame keeps getting cut. I've tried exporting it as a flattened movie through export - QT - "current settings" and through QT conversion, making to sure set the "size" as 720 x 480 ( my sequence presets are as follows: 720 x 480, DVCPRO50) but the default " current size" seems to be set at 640 x 480 and that's how it is exporting it. I must be missing something, I've never had this happen to me before... Any ideas? Maybe I should try trashing the preferences, usually what I do when I'm out of options...Thanks,I just tested a bunch of stuff and the only way it would export correctly was by choosing "none" in the compression dialog box from the export to qt menu. weird hunh?
-
FCPX green frames/artifacts and dropped frames
I have been trying to use FCPX for a couple of weeks now, but haven't been able to. I constantly get green frames/artifacts and dropped frames during playback AND export regardless of using optimixed or proxy media. I am importing mp4 quicktime files, in case that is important.
I am using:
MBP (mid 2009)
OSX 10.6.8
Intel Core 2 Duo @ 2.26 ghz
2 gb ram
Nvdidia GeForce 9400M w/256 vram
I know that it is reccommended I have 4 gb ram, but I meet the minimum requirements and cannot even use the program! Would upgrading to 4-8gb ram resolve this issue? Or is my processor the culprit?
Any help is greatly appreciated.You DEFINITELY need to upgrade your memory to 8GB, etc. Otherwise you will not likely be able to get much real work done at all ... but ... that is likely not exactly the problem you are experiencing now . Since you are talking about bringing in MP4 files, I am thinking you did not get them from a tape-based camcorder. If you did, then they were converted to MP4 afterwards somewhere. Can you play the MP4 files in Quicktime and not see any green screens? If so then have you tried using the FCP X File/Import ... Files command to bring them into FCP X? I have used this with MP4 files without a problem. If Quicktime can play them okay without green frames, and FCP X cannot then the problem does seem to be in FCP X. Are your preferences set to use optimized media? If so then FCP X will convert the files to ProRes and the timeline playback should be okay. There are other "green frames" discussions here that you could also reference. These are just some thoughts.
-
Add frame hold and export frame
hi
i'm working on HD broadcast cartoon animation.
'add frame hold' and 'export frame' are not creating a 2 field, proper frame hold for me - yes i can tweak the field options using 'always deinterlace' or 'flicker removal' but this isnt a fix or a true result of a 'frame freeze'.
is this a bug or am i missing something?
thanks
JoeIs your timeline interlaced?
-
I have lost the instructions for my apachie keyboard and cannot manage to connect it to my iPad. It is fully charged and the Bluetooth is switched on on iPad. Can anyone help me..
This video shows a person pairing that keyboard with the iPad.
http://www.youtube.com/watch?v=zrhrKGQWAdM -
Rectangle frames are missing the frame inside
Hello everyone
I was making a design comp for a website and the Rectangle Frame Tool suddenly stopped displaying the X-shaped frame inside the bounding boxes as shown in the capture below:
I first thought the disappearance of the inside frame may be due to the undefined solid colour, but then setting the solid car would not bring back the frame.
Please someone help me restore the frame.
Thank you in advance,
EadGreat! Switching to the Normal mode has restored the X-shaped frames.
Thank you,
Ead -
Final Cut Pro 7 Frame freezing and dropping frames for 3 seconds...
So, I'm creating a video which leads up to .png files being on screen for 00:00:00:20 and 00:00:00:10. When it hits that first frame of 00:00:00:20, it freezes for 3 seconds, misses out the rest of the frames before continues. What puzzles me is that in the playback window in FCP, it plays exactly how it should but when rendering out into "Apple ProRes 422 (HQ) 1920x1084 60i 48 kHz .mov" format, it plays like this...
It leads me to believe that the frames per second need to be upped but not a cut how to do this on FCP. If this is not the reason for this problem, I'd love to hear from you!
Thanks in advanced!I feel that this is your problem. Editing from a network drive is not particularly ideal as there are quite a few overheads when it comes to data transfer. Bear in mind that in a properly set up network users have a restricted amount of bandwidth to 'play" with so as to minimise horrendous bottlenecks and complaints. Additionally having only 1.9 to 2 GB of free space is a recipe for disaster. The drive could fail miserably and as a result you could lose your work. One thing that is useful to know about conventional drives is that their speed drops dramatically as you fill them up, up to the point that they crawl. I suggest you move your work into a local drive, that is one connected to the computer you use, with ample space to space (filled way below 50% of its capacity). In fact, fcp capture scratch, render and media folders should be there.
Good luck -
i created a .swf slideshow in fireworks and imported it to dreamweaver, but the image has a rather large colored background and there is a frame around the slideshow itself. Is there a way to only display the photos? am i using the correct application. i am using cs4 web premium.
Aperture allows for trimming the audio of any clip that you drop as background music onto the film strip. The clip appears as a green bar, and you can drag it to the place where you want the music to begin, also you can shorten/trim it by dragging the handles at the ends of the audio region.
For example:
If that does not suffice, you can use iTunes to trim the music. For any song in iTunes you can set the start and end time in the "options" pane of the Information panel. Then create a new, shorter version of the song, using the menu
Advanced -> create ... version. -
Received an iPad for Father's Day; during email setup, not able to send a reply to an email as a message appears stateing "Message not sent as server does not allow relaying." Can receive emails with no problem. Whoes server, theirs or mine.
iOS: Unable to send or receive email
http://support.apple.com/kb/TS3899
Can’t Send Emails on iPad – Troubleshooting Steps
http://ipadhelp.com/ipad-help/ipad-cant-send-emails-troubleshooting-steps/
Setting up and troubleshooting Mail
http://www.apple.com/support/ipad/assistant/mail/
Server does not allow relaying email error, fix
http://appletoolbox.com/2012/01/server-does-not-allow-relaying-email-error-fix/
Why Does My iPad Say "Cannot Connect to Server"?
http://www.ehow.co.uk/info_8693415_ipad-say-cannot-connect-server.html
iOS: 'Mailbox Locked', account is in use on another device, or prompt to re-enter POP3 password
http://support.apple.com/kb/ts2621
iPad Mail
http://www.apple.com/support/ipad/mail/
Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
Or this - Delete the account in Mail and then set it up again. Settings->Mail, Contacts, Calendars -> Accounts Tap on the Account, then on the red button that says Remove Account.
Cheers, Tom -
I am unable to reply to emails on both my iPhone and iPad. The message is that the server is unable to relay
create a backup of your information in itunes. update your ios software. reset network settings. if that doesnt work, delete and re add email account.
-
IPad - Jumping Back, Frame Freezes, and the Dot of...
Watching the SPFL game last night was painful enough without the iPad app doing all of the above. I wonder why the buffering spot stays on even once the video feed is obviosly working again, stopping and starting the stream clears this but I had to get off the sofa to do this and am now tired out
This was at my sisters place connected via BT BB at 5.5mbs using the 5GHz band with nothing else connected, picture out to her telly via iPad HDMI adapter. Did any of the 9 or 10 other people watching this game experience similar problems?Hi bonnyrigger,
Thanks for posting. Sorry for the problems with the buffering. Did you have any problems with any other games or was it just this one? I’m assuming it was Hibs v P. T.?
Cheers
David
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-) -
The TMS configuration is inconsistent and The transport route configuration
Hi,
I logged on domain controller in STMS in QA. I can see the following in STMS as
" The TMS configuration is inconsistent
The transport route configuration is inconsistent"
Users were able to do transports and there were no issues.
Transport routes
DEV>QA>PRD
TST(which is not active)
Environment:
Oracle: 10.2.0.4.0
Windows NT
Netweaver 70 ehp1 abap
Please guide me how to resolve the above issue.
Thanks and Regards
SatyaHi,
Everything is tick marked.
Please find the output.
Check Transport Directory 03/30/2011 08:34:16
QA1 CAL - Quality
Transport Directory
bin
sap2bksrv\sapmnt\trans\bin
Create Test File
Read Test File
Delete Test File
buffer
sap2bksrv\sapmnt\trans\buffer
Create Test File
Read Test File
Delete Test File
cofiles
sap2bksrv\sapmnt\trans\cofiles
Create Test File
Read Test File
Delete Test File
data
sap2bksrv\sapmnt\trans\data
Create Test File
Read Test File
Delete Test File
log
sap2bksrv\sapmnt\trans\log
Create Test File
Read Test File
Delete Test File
sapnames
sap2bksrv\sapmnt\trans\sapnames
Create Test File
Read Test File
Delete Test File
tmp
sap2bksrv\sapmnt\trans\tmp
Create Test File
Read Test File
Delete Test File
Thanks and Regards
Satya -
Refreshing one frame only in a frame page
Hi all,
Pls help....i have this frame page with 4 frames. each one when click targets to another one on the same page...The last frame is a page which has 2 buttons Delete and Confirm and it has checkboxes.....when the checkbox are clicked and user clicks on Delete this specific frame page needs to be refresh and display the upated value....Right now it when i click on delete, it is being redirecting to blank window with the updated value and i need to click back to see the frame pages and the frame updated..which i do not want. Upon clicking Delete i want this specific frame to refresh and display the updated value....Pls help meeeeeeeeeeethanx a lot......geee....u have been of great help...i wrongly specified the target for my button in my javascript......
-
Configuring CE-PE link on Frame Relay over ATM
Hi!
Need you guys expert opinion on how to configure configuring CE-PE link on Frame Relay over ATM. I am stump by this one because I never done it before. The CE is a Cisco 7206 with ATM PA and the parameters given to us is DLCI number in x/y format...isn't that the format for PVC. When asked, my SP contact says that it is indeed FR over ATM. Any of you guys who have experience to guide on this or point me in the right direction is most welcome. Thanks
Rgds
HelmeHello Helme,
ask your provider if they are doing FR to ATM service interworking.
In that case one side is configured for Frame-Relay and the other side for ATM
Service interworking is done by provider.
Verify that you have the same MTU on both sides and configure following ISP specifications
ATM uses two numbers to identify a PVC
int atm 4/0
no ip address
no shut
int atm 4/0.1 point-to-point
mtu 1500
ip address x.x.x.1 255.255.255.252
pvc x/y
enc aal5snap
protocol ip x.x.x.2 broadcast
this should be enough to have it working
on the other side configure or have a point-to-point subif configured on FR
see this example
http://www.cisco.com/en/US/tech/tk39/tk53/technologies_configuration_example09186a00801747e3.shtml
Hope to help
Giuseppe
Maybe you are looking for
-
Repairing boot drive from an external drive
I want to verify and if need be repair my startup disk (as i have never done it). I don't have access to my original install DVD as it is in an apartment overseas! But is this safe or possible? My system is 10.4.4 but I have a bootable version 10.2.8
-
I walked away from my Imac 24" Intel (white) yesterday and when I came back it seemed as though the Imac went into sleep mode (although its not set to go into sleep mode in my account). Anyways I hit the space bar and few other keys also tried mouse
-
Hi All, I am implementing an Inbound INVOIC02 IDoc for posting Credit Memo that references purchase order. But there is some unique thing. This IDoc is used to post only the SAC (D240 - Freight Allowance). Freight Allowance will come at Header level
-
Pop-up windows in webmin filemanager are behind the firefox app
When i use the java filemanager application within webmin to administer my websites all the java app windows are poping up behind the firefox screen. The only way to edit information in the "pop under" java windows is to move the firefox window to th
-
We have installed Weblogic Server 10.3.6 on a Oracle Linux x86_64 test server (5GB RAM) and Configured RTD and Webcenter in one domain.We are using single database for these two products, after starting Admin Server we are only able to start one mana