Configuring HSRP in Cisco 6509

We have 2 nos Cisco 6509 switches with MSFC II . VLAN's are configured in both the 6509's and now we need to have the HSRP for redudancy.

Dear Anand,
It is really helpfull info for me also.I am having same set up But my one 6509 again connect to tw0 3725 routers where i am using HSRP.Please fine set up below
Customer end Router --- > Ethernet1------> 6509-A ---->3725 Router-1 (Standby 3725 Rou-2 )---> Remote Location
Customer end Router --- > Ethernet2------> 6509-A ---->3725 Router-1 (Standby 3725 Rou-2 ) ---> Remote Location
My Problem is that i need full redundancy between customer router and 3725 routers also.
If i cross connect 3725 Routers on both 6509 then how existing HSRP of 3725 will work.
TIA
Regards
SAM

Similar Messages

How can i configure hsrp in cisco 3850 switch please guide me

how can i configure hsrp in cisco 3850 switch please guide me

Hi Mauleshg,
Please the below mention link to configure Hsrp hope this will help you.
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3850/software/release/3se/ip/configuration_guide/b_fhrp_3se_3850_cg/b_fhrp_3se_3850_cg_chapter_010.html
Br.
Mohseen Patel

Configuring HSRP in Cisco Switches using Dynamips

Dear Friends,
I am in process of configuring hsrp using dynamips
   when i am putting the comand
    SW1(config)#standby 1 ip 10.1.1.10
                                           ^
% Invalid input detected at '^' marker.
   its showing error i,e the command is support by switch ios
Please check the show version command for ios details
"SW1#sh version Cisco IOS Software, 3600 Software (C3640-IK9O3S-M), Version 12.4(7), RELEASE SOF TWARE (fc6) Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2006 by Cisco Systems, Inc. Compiled Wed 01-Mar-06 00:58 by alnguyen ROM: ROMMON Emulation Microcode ROM: 3600 Software (C3640-IK9O3S-M), Version 12.4(7), RELEASE SOFTWARE (fc6) SW1 uptime is 3 hours, 13 minutes System returned to ROM by unknown reload cause - suspect boot_data[BOOT_COUNT] 0 x0, BOOT_COUNT 0, BOOTDATA 19 System image file is "tftp://255.255.255.255/unknown"    Cisco 3640 (R4700) processor (revision 0xFF) with 94208K/4096K bytes of memory. Processor board ID 00000000 R4700 CPU at 100MHz, Implementation 33, Rev 1.2 16 FastEthernet interfaces DRAM configuration is 64 bits wide with parity enabled. 125K bytes of NVRAM. 8192K bytes of processor board System flash (Read/Write) Configuration register is 0x2102 "
Can anyone help me in solving this issue. Any kind of help is greatly appreciated

Hi,
SW1(config)#
you have to be in (layer-3) interface configuration mode, e.g. on a SVI:
R1#conf termR1(config)#interface vlan1R1(config-if)#standby 1 ip 1.1.1.1
Hope that helps
Rolf

HSRP on 3750 & 6509

Hi,
We have got Cisco 6509(Main) & 3750(Standby), 6509 has got L3 card & HSRP is running & 3750 also running HSRP, i know that 6509 & 3750 should hav connectivity each other while running HSRP, so that even if 6509 fails automatically 3750 becomes active swtich, i know theoritcially it works,but practically i havn't tried this. so can any lemme know whether some one has tried this in pratically & got worked? thanks in advance.

Yes it will work. HSRP is not platform dependent and can be configured across different platforms. I have few customers implement HSRP this way.

LLQ priority issue after upgrading to Sup32 on Cisco 6509

Hi,
I have 1x Cisco 6509 with Sup2 and MSFC2 and it is running on IOS (c6k222-jk9sv-mz.122-17d.SXB11).
I have following policy map :
Policy Map VOIP
Class IPPHONE
priority percent 75
and the following command on each interface:
service-policy output VOIP
those configuration are working fine on SUP2 with MSFC2 but last week I tried to upgrade the SUP2 to SUP32 on the switch and upgrade the IOS to the latest version (s3223-adventerprisek9-mz.122-33.SXJ4)
but when I try to put service-policy output VOIP on each physical interface I am getting the following error:
"Priority command is not supported in output direction for this interface"
and when I try to add service-policy output VOIP on a VLAN interface I am getting following error:
MQC features are not supported in output direction for this interface.
Please let me know if I need to change something after upgrading to SUP32.
Thanks

Hi
Hi
Sup32 uses PFC3B for Hardware forwarding and implemenation of features like qos, acl, netflow etc
PFC QoS does not support these policy map class commands:
•bandwidth
•priority
•queue-limit
•random-detect
•set qos-group
•service-policy
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SX/configuration/guide/qos.html
Thanks
Raju

Cisco 6509 with Reliability 255/255, txload 238/255, rxload 8/255 interface

Hi there,
I'm having an issue with my Cisco 6509. One of Internet configured as trunk Interface direct with a HP7500 is showing reliability 255/255, txload 238/255, rxload 8/255.
The Issue is that my Cacti Server show me that only 10% of the link is in use but if you look at txload you can see that almost 100% of the bandwidth is in use..
What can I do in order to figure out what's going on with this Interface. I'm thing about to put wireshark and configure a port monitor in order to capture the packets.
Is anyone has any tip to do a troubleshoot with this issue??
SWITCH01#show int port-channel 10
Port-channel10 is up, line protocol is up (connected)
Hardware is EtherChannel, address is c47d.4fbf.a8c2 (bia c47d.4fbf.a8c2)
Description: CORECISCO_X_COREHP
MTU 1500 bytes, BW 2000000 Kbit, DLY 10 usec,
reliability 255/255, txload 238/255, rxload 8/255
Encapsulation ARPA, loopback not set
Full-duplex, 1000Mb/s
input flow-control is off, output flow-control is unsupported
Members in this channel: Gi8/19 Gi8/20
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters 1w0d
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 66043000 bits/sec, 23041 packets/sec
5 minute output rate 1871148000 bits/sec, 186439 packets/sec
15127300343 packets input, 6121405739799 bytes, 0 no buffer
Received 232321316 broadcasts (161670914 multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
118621325538 packets output, 141124879219641 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
SWITCH01#
Regards
Adriano

This pretty much tells you your port channel is pretty full. How many ports in the channel?
5 minute input rate 66043000 bits/sec, 23041 packets/sec
5 minute output rate 1871148000 bits/sec, 186439 packets/sec

Regarding LACP commands on Cisco 6509 to connect server

Hi All ,
We have to connect two servers to cisco 6509 (sup720 with MFFC R7000) switches and we have to configure LACP on the 6509 to bundle two ports to get 2 Gbps through put.
Each server has four NIC ports ..out of which two ports will be connected to Switch 1 ( active ) and remaning two ports will be connected to switch 2 ( standby).
We are going to use below commands for LACP on both the switches.Apart from below commands do we need to have any other commands to make LACP to work as soon as we connect the servers.
Switch 1 :
set channelprotocol lacp 1
set port lacp-channel 1/1-2 73
set port lacp-channel 1/1-2 mode active
Set port vlan 10 1/1-2
set spantree bpdu-guard 1/1-2 enable
set port lacp-channel 1/9-10 85
set port lacp-channel 1/9-10 mode active
Set port vlan 10 1/9-10
set spantree bpdu-guard 6/9-10 enable
On the MFFC we have so many vlans along with vlan 10
int Vlan 10
ip address 10.10.10.2 255.255.255.0
standby 10 ip address 10.10.10.1
standby 10 timers 1 3
standby 10 priority 200
same series of port will be used on Switch 2 to connect servers.
Servers support LACP protocol only.
diagram is enclosed...If any suggetions on this would be appreciated..
Thanks ,
M S K

Interesting I thought all sup 720's were non hybrid and used IOS only . Guess you learn something everyday. Looks like it should work with what you
have as long as the servers are setup with lacp in a active/standby mode.

Port mirroring on cisco 6509

We have cisco 6509,Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI2a, RELEASE SOFTWARE (fc2).
I want to know, at a time how many interfaces can be configured as a source interface and at a time how many interfaces can be configured as a destination interface?

The 9100EM does not support port mirroring.
You might want to find a hub and use that to mirror the traffic.
http://shop.ebay.com/?_from=R40&_trksid=p5197.m570.l1313&_nkw=ethernet+hub&_sacat=See-All-Categories
Be careful though, many of those listed claim to be hubs are not and are in fact switches.

Cisco 6509 with 10G Module

Hello,
We have Cisco 6509 Core Switch with following details & we need to install WS-X6716-10T-3C module in int.
Can some body advise which slot number i should use in 6509 ?
Do i need to upgrade supervisor engine IOS for this ?
Is it hot swapable module & can i install this module in production ?
6509_CORE#sh ver
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI6, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Mon 28-Mar-11 12:09 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)SX7, RELEASE SOFTWARE (fc1)
6509_CORE uptime is 2 years, 30 weeks, 1 day, 3 hours, 13 minutes
Uptime for this control processor is 2 years, 30 weeks, 1 day, 1 hour, 44 minutes
Time since AUB_CORE switched to active is 2 years, 30 weeks, 1 day, 1 hour, 44 minutes
System returned to ROM by power cycle at 11:55:23 UTC Wed Apr 27 2011 (SP by power-on)
System restarted at 11:16:22 AST Sun Jun 26 2011
System image file is "sup-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXI6.bin"
Last reload reason: Reload Command
cisco WS-C6509-E (R7000) processor (revision 1.5) with 983008K/65536K bytes of memory.
Processor board ID SMC1426001S
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from s/w reset
4294967295 Ethernet interfaces
33 Virtual Ethernet interfaces
150 Gigabit Ethernet interfaces
100 Ten Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
6509_CORE#sh module
Mod Ports Card Type                              Model              Serial No.
1   24 CEF720 24 port 1000mb SFP              WS-X6724-SFP       SAL1430P2QU
2   48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX     SAL1429N6XB
3   16 CEF720 16 port 10GE                    WS-X6716-10GE      SAL1430NYUE
4   16 CEF720 16 port 10GE                    WS-X6716-10GE      SAL1430NX5A
5    5 Supervisor Engine 720 10GE (Active)    VS-S720-10G        SAL1430NUJE
7   16 CEF720 16 port 10GE                    WS-X6716-10GE      SAL1645RJTF
Mod MAC addresses                       Hw    Fw           Sw           Status
1 d0d0.fd62.d9e0 to d0d0.fd62.d9f7   4.4   12.2(18r)S1 12.2(33)SXI6 Ok
2 c84c.75b8.596c to c84c.75b8.599b   3.4   12.2(18r)S1 12.2(33)SXI6 Ok
3 001f.6cac.11d0 to 001f.6cac.11df   1.0   12.2(18r)S1 12.2(33)SXI6 Ok
4 5475.d06e.0988 to 5475.d06e.0997   1.0   12.2(18r)S1 12.2(33)SXI6 Ok
5 001e.4a7f.3068 to 001e.4a7f.306f   3.2   8.5(4)       12.2(33)SXI6 Ok
7 fc99.4736.2d80 to fc99.4736.2d8f   1.1   12.2(18r)S1 12.2(33)SXI6 Ok
Mod Sub-Module                  Model              Serial       Hw     Status
1 Distributed Forwarding Card WS-F6700-DFC3C     SAL1430P282 1.4    Ok
2 Centralized Forwarding Card WS-F6700-CFC       SAL1430NRAS 4.1    Ok
3 Distributed Forwarding Card WS-F6700-DFC3C     SAL1430P26L 1.4    Ok
4 Distributed Forwarding Card WS-F6700-DFC3C     SAL1430NZRM 1.4    Ok
5 Policy Feature Card 3       VS-F6K-PFC3C       SAL1429N6B7 1.1    Ok
5 MSFC3 Daughterboard         VS-F6K-MSFC3       SAL1430NN3R 5.0    Ok
7 Distributed Forwarding Card WS-F6700-DFC3C     SAL1644RAZF 1.5    Ok
Mod Online Diag Status
1 Pass
2 Pass
3 Pass
4 Pass
5 Pass
7 Pass

Hello cmarva,
I got power requirement from core switch:
6509_CORE#show power
system power redundancy mode = redundant
system power total =     3795.12 Watts (90.36 Amps @ 42V)
system power used =      2748.06 Watts (65.43 Amps @ 42V)
system power available = 1047.06 Watts (24.93 Amps @ 42V)
                        Power-Capacity PS-Fan Output Oper
PS   Type               Watts   A @42V Status Status State
1    WS-CAC-4000W-INT   3795.12 90.36 OK     OK     on
2    WS-CAC-4000W-INT   3795.12 90.36 OK     OK     on
                        Pwr-Allocated Oper
Fan Type               Watts   A @42V State
1    WS-C6509-E-FAN      210.00 5.00 OK
                        Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type          Watts   A @42V Watts   A @42V State State
1    WS-X6724-SFP        162.96 3.88   162.96 3.88 on   on
2    WS-X6748-GE-TX      325.50 7.75   325.50 7.75 on    on
3    WS-X6716-10GE       457.80 10.90   457.80 10.90 on    on
4    WS-X6716-10GE       457.80 10.90   457.80 10.90 on    on
5    VS-S720-10G         338.10 8.05   338.10 8.05 on    on
6    (Redundant Sup)       -     -      338.10 8.05 -     -
7    WS-X6716-10GE       457.80 10.90   457.80 10.90 on    on
system auxiliary power mode = off
system auxiliary power redundancy operationally = non-redundant
system primary connector power limit =   10920.00 Watts (260.00 Amps @ 42V)
system auxiliary connector power limit = 10500.00 Watts (250.00 Amps @ 42V)
system primary power used =              2748.06 Watts (65.43 Amps @ 42V)
system auxiliary power used =            0 Watt
As per Cisco document i require this power WS-X6716-10T-3C: 509.3W (12.1A @ 42V) & from output available power is system power available = 1047.06 Watts (24.93 Amps @ 42V)
Looks like im good to go. Can you verify please ?
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6500-series-switches/product_data_sheet09186a00801dce34.html
Regards,

CatOS image upgradation in Cisco 6509

what is the procedure for upgrading the CatOS in Cisco 6509, can any provide step by step configuration?

The link below has the step-by-step procedure to upgrade the CatOS image.
http://www.cisco.com/en/US/products/hw/switches/ps700/products_configuration_example09186a0080116ff0.shtml
HTH,
Sundar
*Please rate all helpful posts.

Do i have to configure ssl on cisco unified provisioning manager for it to work. I am running BE6000 9.X

Do i have to configure ssl on cisco unified provisioning manager for it to work

Here is the code
#include <userint.h>
#include "iface.h"
#define DAQmxErrChk(functionCall) if( DAQmxFailed(error=(functionCall)) ) goto Error; else
int write_onoff(uInt8 HL, const char linename[])
int         error=0;              // error code (initialized to zero i.e. no error)
TaskHandle taskHandle=0;            // task ID for DAQmx
char        errBuff[2048]={'\0'}; // error message
// DAQmx Configure Code
SetWaitCursor(1);
DAQmxErrChk(DAQmxCreateTask("", &taskHandle));
DAQmxErrChk(DAQmxCreateDOChan(taskHandle, linename, "", DAQmx_Val_ChanPerLine ));
// DAQmx Start Code
DAQmxErrChk(DAQmxStartTask(taskHandle));
// DAQmx Write Code
DAQmxErrChk(DAQmxWriteDigitalU8(taskHandle, 1, 1, 10.0, DAQmx_Val_GroupByChannel, &HL, NULL, NULL));
Error:
   SetWaitCursor(0);
   if (DAQmxFailed(error)) DAQmxGetExtendedErrorInfo(errBuff, 2048);
   if (taskHandle!=0)
      // DAQmx Stop Code
      DAQmxStopTask(taskHandle);
      DAQmxClearTask(taskHandle);
   if (DAQmxFailed(error)) MessagePopup("DAQmx Error", errBuff);
return error;
} // end write_digital_line
int CVICALLBACK test (int panel, int control, int event, void *callbackData, int eventData1, int eventData2)
uInt8 onoff=0;
if (event==EVENT_COMMIT)
    GetCtrlVal(panel, control, &onoff);
   write_onoff(onoff, "Dev1/port0/line0");
return 0; // return 0 to tell the system the message has been handled

What's "SAVE" configuration command for Cisco switch/ router?

What's "SAVE" configuration command for Cisco switch / router? I know Switch#copy running-config startup-config works well,
but so long, any other command that easy to remenber?

What's "SAVE" configuration command for Cisco switch / router? I know Switch#copy running-config startup-config works well, but so long,
any other command that easy to remenber?
yes, here: Switch#write,and want to know more about the Cisco switch, please visit:http://www.3anetwork.com/cisco-switches-price_c1

ThinkPad USB 3.0 dock network port has problems with our Cisco 6509 switch

We purchased a ThinkPad USB 3.0 dock for and X1 carbon and the main issue we are having is the network port does not seem to work with our Cisco 6509 switch. I tried updating the firmware on the dock but it still hasn't fixed the issue. I was wondering if anyone else had run into this problem with any other networks out there.

I'm seeing the same issue with a ThinkPad W520. When I connect my ethernet cable directly to the laptop, my internet speeds are on par with my service provider of 18 Mbps. When I move that cable to the dock, I will only see 1.5 Mbps. I have two displays attached to the dock and I'm running Windows 7. I've updated the dock firmware and have installed the latest system drivers. Is there anything else to try?

Send configuration file to Cisco router

Where can I find a C programm that send configuration file to Cisco router from linux workstation?

I wonder what kind of config changes you are making and whether that may have an impact on SSH. For example if you change the host name or change the domain name then the keys need to be regenerated.
HTH
Rick

Ciscoview Cisco 6509 VSS power supply LED indicators incorrect

Hello all
i am experiencing the following problem.
In the Ciscoview, the LED indicators of the power supply of Cisco 6509 VSS are represented incorrectly. All power inputs and fans are okay actually. however, in the ciscoview, there is only 1 green "INPUT OKAY" for each power supply. And "FAN OKAY" LEDS are off on Active chassis.
Any assistance would be greatly appreciated.
LMS 4.1
IOS Version 12.2(50)SY1
Device Package:
38.
Cat6000
12.0
Cat6000 Package
39.
Cat6000IOS
37.0
Cat6000IOS Device Package

Check the PS at the back, is there a light? If there's no light, then you need to RMA the PS as it could be faulty.
If there's a light on the PS, then you need to RMA the switch.

Configuring HSRP in Cisco 6509

Similar Messages

Maybe you are looking for