Configuring Integrated Planning

Hi All,
We are planning to configure BI - IP.
The server available is SAP NetWeaver 2004s ( Abap + Java ).
Support Packs :
SAP_ABA               700      0014   SAPKA70014   Cross-Application Component
SAP_BASIS            700      0014   SAPKB70014   SAP Basis Component
PI_BASI      2005_1_700      0014   SAPKIPYJ7E    PI_BASIS 2005_1_700
SAP_BW                700      0016   SAPKW70016 SAP NetWeaver BI 7.0
BI_CONT                703      0012   SAPKIBIIQ2    Business Intelligence Content
If any one configured, please advice that the above status will be sufficient to configure or any thing else required.
Also, Please provide the steps for configuring.
Regards,
Venu

self

Similar Messages

Configuration Requirement for Integrated Planning in BI 7.0 with JAVA Addin

Hi,
We have BI 7.0 with Java Add-in installation newly migrated to Unicode.
BW consultants (I am BASIS Consultant) want to use "Integrated Planning". I already checked IMG link of it & JCO destinations mentioned there are not in J2EE engine.   Even I am not able to create b'cos current setup is not on SLD.
I would really appreciate your help on below queries :
1) Can I configure Integrated Planning without using SLD ?
2) Do I need to install BI JAVA to running Integrated Planning ?
3) Do I need to install EP & EP Core ?
I already checked most of SDN thread but sorry couldn't able to get answer to above questions.   I have checked SAP Notes : 901022, 919850, 917950.
Your early reply would be highly appreciated.
Thanks & Regards,
Narsing.

Hi Balaji,
Thanks for information.   One thing to update with JAVA/JAVA addin portal core components gets installed.   So I didn't installed EP.
Now Integrated Planner is working fine.
Thanks for your help.
Best Regards,
Narsing.

Integrated planning configuration guide

Hi,
I would appreciate if anybody could send me a configuration guide witha general scenario for integrated planning.I tried the best practice side ,but the sales planning/cost center planning(planning scenarios ) are for bps
regards
savi

As per my understanding functional config. remain the same ,however the technical configuration for IP is different from BPS.
Check below for Modelling Scenarios -
http://help.sap.com/saphelp_nw2004s/helpdata/en/43/1d2440301a06f4e10000000a422035/frameset.htm
Sales Planning & Sales Analysis
http://help.sap.com/bp_biv335/BI_EN/html/BW/SalesPlan.htm
Hope it Helps
Chetan
@CP..

Approve and Notify in Integrated Planning

I am wanting to implement an Approve and Notify functionality in my planning application in Integrated Planning.
i.e. When all assistants have submitted their yearly goals, I want to be able to notify the regional manager that they can begin reviewing the goals. Also, when the regional manager has approved them (and performed a few functions), I want to be able to email the assistants.
I am wanting to avoid using BPS - STS if at all possible. Is there a way to have FOX Formula, or some other function, email the users when this has been performed?
I was thinking about marking a submit flag when the assistants submit their hours, and when all flags have been marked for a region, it will notify their manager.
Thoughts?

Hi,
It's quite difficult to track the status of the goal submission by all assistants if you are not using STS.
But you can send mails to assistants when their goals are approved by writing ABAP. You can't achieve that via FOX.
Try to use STS as that will fulfill all your requirements with minimal configuration efforts and no programming. Also, you will not require additional characteristic and programming logic for FLAG.
But if anyways you don't want to use STS let me know, I have the code for sending emails via planning function exit.
Regards,
Deepti

Integrated planning-config guide for a scenario

hi,
Aappreciate if sombody could help me out witha configuration guide for integrated planning for scenarios of cost/profit planning etc...i tried best practice side but the docs were more of BPS
email id:[email protected]
regards
savi

This could be useful.
http://help.sap.com/bp_biv335/BI_EN/html/BW/SalesPlan.htm

Business Objects and SAP BI Integrated Planning material

hi
guys
i am looking for Business Objects and SAP BI Integrated Planning any material site plz send me
regards
suresh

Hi ,
Please find these blogs by Ingo. This should help you.
BusinessObjects and SAP - Installation and Configuration Part 1 of 4
Install Part #1
BusinessObjects and SAP - Installation and Configuration Part 2 of 4
Install Part #2
BusinessObjects and SAP - Installation and Configuration Part 3 of 4
Install Part #3
BusinessObjects and SAP - Installation and Configuration Part 4 of 4
Install Part #4
BusinessObjects and SAP - Configure SAP Authentication
SAP Authentication
BusinessObjects Integration with SAP NetWeaver BI - Technical Material
Thanks,
Gopi

BI Integrated Planning - Error config logon tickets

Hi,
I am trying to use the Integrated Planning module in 2004s, when I select the start modeler, I get an error relating to the configuration of SAP logon tickets.
Both the required profile parameters are set to the correct value:
login/create_sso2_ticket = 2
login/accept_sso2_ticket = 1
Does Integrated Planning have to use sso?
Thanks
danjl

Hi Dan,
Hope this links gives you better insight on Integrated Planning:
http://help.sap.com/bp_epv170/EP_US/Documentation/How-to/Installation/Upgrade_NW2004s_JavaSR1.pdf
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/c0ac03a4-e46e-2910-f69d-ec5fbb050cbf
Assign points if useful.
Regards
Vishwanath

Integrated Planning NW04s

Must SEM be configured in ECC as a prerequisite to using Integrated Planning NW04s? Or can Integrated Planning NW04s work with non-SEM business content?

Hi
As far as I know the integrated planning is a part of BW-BPS so it will work without having SEM. Some of the standard SEM functions might not be available.
thanks

CCA and PCA retraction in Integrated Planning

Hi all,
Please I need some orientation about CCA an PCA retraction when you are using Integrated planning.
I read blogs about CCA retraction (made by Praveen Mayalur) and was very helpfull, but it only refers a planning scenario using BW-BPS, and I don't have the same structure to send the data in the integrated planning.
I had looked in SDN and SAP portal, and I can't find anything about it.
I hope you can help me.
Thanks in advance, best regards
Inge Eichhorns

Hi
1) Retraction are driven by BPS, IP is not equipped with Retraction.
2) Cost Center & Internal Order Retraction should be configured through in BPS--> Planning Area; Planning Level, Planning Function; Parameter Group.
3) You need to configure Source Structure, based on business requirement you need to ensure that the retraction happens either in CO Currency or Transaction Currency.
4) Try to use the SAP Standard Function Modules for Cost Center and Internal Order Retraction. Refrain from copying & modifying the same.
go through the Cost Center Retraction relevant documents and they are very helpful.
5) Function Modules for Profit Center Retraction are not available in ECC due to the New GL Concept.
6) If possible advise the Business to use "File Upload" for Profit Center Data.
Regards
Srinivas

Integrated planning in sneak preview of java and abap versions of nw 2004s

Hello all,
I installed both AS ABAP and AS JAVA of the sneak preview netweaver 2004s,but unable to run integrated planning.I searched the forum and sap notes but did not find specific required steps to configure.Anyone able to run integrated planning of the preview versions ? does it involve extensive configuration ? Could someone post the necessary steps to configure.I checked the SLD and it is running but did not have any 'technical systems' configured.I created a technical system for ABAP and JAVA manually myself.The jco destinations still shows 'No SLD connection' with a red button beside it.
Then I went to visual administrator and checked SLD data supplier service.It looks like it is lot of BASIS work to configure this.Please let me know if someone has simple steps to configure and run integrated planning just after installing sneakpreview versions of nw 2004s ABAP and JAVA.
Thanks

Hi Steffen,
all you need for this type of communication is already included in the WAS. There's a lot of documentation available:
JCO (Java Connector for ABAP backends): http://help.sap.com/saphelp_nw04/helpdata/en/35/42e13d82fcfb34e10000000a114084/frameset.htm
Generating proxies "around" JCO (very useful feature of the developer studio):
http://help.sap.com/saphelp_nw04/helpdata/en/ed/897483ea5011d6b2e800508b6b8a93/frameset.htm
Using ABAP EIS in a transactional J2EE environment via J2EE connector architecture: http://help.sap.com/saphelp_nw04/helpdata/en/6f/1bd5caa85b11d6b28500508b5d5211/frameset.htm
This should be sufficient for the beginning
Hope that helps.
Best regards
Stefan

Issue with Input Ready Query in Integrated Planning.

Hello Everyone,
I've been working on Integrated Planning for some time now. My company recently started using a new server for this work. I find that I am unable to make the queries "input ready". Though I edited the properties of the key figure to "accept user entered values" and chose the option to "start query in change mode", when I execute the query, I find that it the values for the Key Figure cannot be changed. I tried to search in the OSS for any note(s) regarding this issue, but was unable to come up with a solution. Is the problem related to the server or is there some other configuration that I should take care of? Additionally, I would also like to know if there is any method to debug such a problem. I would appreciate it if someone could help me out in this regard.
Thanks,
Jake.

Hi,
Please verify the following.
1. Check if the underlying realtime cube is in "Planning Mode:Loading not allowed" state in rsa1
2. If you have created an aggregation level, Check if the most detailed information is available at that Aggregation Level(i.e, include characteristics so that the record can be uniquely identified at that aggregation level).Best would be to include all characteristics and create a query first and ensure it works.Then remove unwanted charecteristics one by one, so that you can fix the issue.Best thing to start with is to create the aggregation level on top the real time cube itself.
3. Check for any characteristic restrictions been defined for the real-time cubes.If so, try removing them temporarily and execute the query
4.Also check if any data slices has been created on the real time cube. If so, try removing it temporarily and then execute the query.
5. Set the property for Planning "Start query in Change Mode"- this is for th Query
6. Set the 'Key Figure' Planning Property to "Can be changed Manually or via Planning Functions" for the appropriate KeyFigures- this is for the key figures
7. Try removing the currency/unit from row/column. Try restricting them in filters rather than in row/columns.
8. Check if there are any locks occurring due to filter., i.e if you are using a filter and even if 1 record of this selection locks with another user's selection you lose the input readiness.
Mostly this should fix the issue. Assign points if this info helps you.
Thanks,
Balaji.

Is BI Integrated Planning / STS right tools for this kind of application

Hi Everyone,
I need your advise/help. I need to create a simple web application to do as below:
1) Data Entry Form on web - Enter / Edit / Delete data i.e. order entry
2) Save the data in BW cube or datastore
3) E-mail to Managers for approvals
4) Click a button to approve
5) Retrieve the data from BW and show it as a web report
Is BI Integrated Planning / STS right tools for this kind of application? If yes, can you please recommend some documentations?; if no, Which tool will be the best fit for this kind of requirement?
Thanks a Million, Jin Freda

STS allows you to lock/release/approve one set of plan data (say many records). I thought your requirement is to approve individual order documents. configuring this in STS would be unnecessarily complicated I think.
Similarly IP is to work on a set of data (say all order quantity for a region or period), not for individual orders. Building all the checks and validations that you would probably want in an order entry may not be easy to build in IP.
VC or Webdynpro can't post to a infocube. They can certainly write to a transactional ODS (which probably would be a better place to write such data).
I have limited knowledge of your requirement so can't say whether it is a problem - probably not a show-stopper. If you are entering a set of orders in one go, may be IP is appropriate, but if you are looking for an application where users may be posting individual orders at random times, IP would be a bad choice I think.

Problems with BI Integrated Planning

Hello, everybody,
We installed BI 7.0 and want to use BI Integrated Planning, but then i connect to Modeler Wizard i get error No JCO Connection. Our BASIS Team can't find an issue.
Maybe there is some kind of configuration in BI side, not just in BASIS?
Could you give us some advice?
Thanks in advance.
Best Regards,
Arunas Stonys

Joanne,
Are you still having issues with BI-IP? I have been troubleshooting with the basis folks in getting BI-IP up on a new system over the last few day to a week and have now gone through the process myself whereas before I had been given a system already set up. I have enclosed some troubleshooting feedback with my counterpart in getting the system up.
What type of issue are you having?
Can the basis folks start the planning modeler or planning wizard in RSPLAN even if you can't?
1. The note mentioned above 919850 and the help documentation in SPRO under
SAP NETWEAVER->Business Intelligence->BI Integrated Planning
are very helpful. They have to set the following Jco Destinations in Web Dynpro Content Administrator:
BI_MODELDATA
BI_METADATA
WD_ALV_MODELDATA_DEST
WD_ALV_METADATA_DEST
And the problem was the connection to the message server. It was not possible to connect without having a Logon group assigned. This had to be done in WI4 ABAP as well as in the SLD for this system. After that assignment connection was no problem.
2. make sure you have the portal ips in your host file.
3. have they have created an account for you in client 001 of the NW04S?
4. Have they created a portal id for you and assign the portal role com.sap.ip.bi.business_planning_showcase to you?
5. have they configured the setting for starting the planning modeler (also under SPRO)..
Hope this helps. If you have more specific questions, feel free to e-mail me directly.
Mary

Status and Tracking system (STS) with BI Integrated Planning ?

Hi, is posible get some images or demo for show my clients ?
i am reading Salp Help
http://help.sap.com/saphelp_nw04s/helpdata/en/b6/92bc7479fb11d5b3df0050dadfb23f/frameset.htm
and say :
You can use the BW-BPS Status and Tracking system (STS) with BI Integrated Planning. This is useful if you are already using BW-BPS with the Status and Tracking system but want to use additional functions from BI Integrated Planning.
What is additional functions from BI Integrated Planning ?
Is posible write free text in some areas for planning and option for look from high levels ?
Is posible Insert in the proces STS to "Area Manager" only for look status the Planning (open, in process or finishing) ?
General manager --> Lock when is finishing.
Area manager--> only look status the Planning ?
Submanager of area --> Responsable, Aproval, etc.
planning1
planning2
planning3
planning4
planning5
Submanager of area : Planning TOO.
Thank you ... This is important info and get some images the last version in STS working in web mode, for my client buy the product.

Hi Bala ,
Yes you can use the STS for BI IP also and you need to configure the Planning level and sub plan area and follow the steps to set up STS.
STS still has BPS flavour and can be used in IP.
Hope this helps
Raja

Questions about Integrated Planning and BPS

Hi all,
I'm testing the functions of BW7.0. And at the point of comparing the new BI Integrated Planning from the BPS, I'm stuck with 3 problems. Can anybody give me some solution?
i. When using the input-ready layout of the BW-BPS 3.5, I was able to create a new record and load it up to the cube. Is it possible to make the same operation like this using the BI Integrated Planning of BW7.0?
ii. When using the BW-BPS 3.5, showing the character hierarchy on the Manual planning layout can be chosen. And I'd like to show the BPS Characteristic Hierarchies in BI Integrated Planning of BW7.0 like it is in the BW-BPS 3.5. Is it possible to show the hierarchy in similar type somehow? If not,can't I show the sum of it anyhow? And if possible,can you also show the sum of the each hierarchy and change the data?
iii. When showing the Characteristic combination data, can you choose how to show them from the transaction data or from all the combination like it was possible in the BW-BPS 3.5?
Kind regards,
Hiroshi Iwanaga

Dear Beat,
Thanks for your help.
The information you gave me made a lot of help.
Can I ask you more about the first question?
About getting new lines in the table web item,as you have told me, I have set the parameter NEW_LINES_COUNT as 20 in the table web item. But when I execute it,no lines shows up. Is this a program error or am I setting the parameter in a wrong place?
And this getting new lines feature, is it also possible when using a workbook?
Thanks in advance,
Hiroshi Iwanaga

Configuring Integrated Planning

Similar Messages

Maybe you are looking for