Configuring IP SLA in cisco 3925 router.

HI Team.we need to configuring IP SLA in cisco 3925 router with c3900-universalk9-mz.SPA.151-4.M4.bin ios. For Monitoring purpose. Earlier we have used the rtr command for the same. Now we are going with new Cisco 3925 router. with the above mentioned IOS. Pls suggest whether we can configure the IP SLA in the router with Licence. Or We need to buy the licence for the ame.
Posted by WebUser Ramkumar Selvaraj from Cisco Support Community App

Hi
I think the command has been updated - rather than 'rtr responder' it's now 'ip sla responder'.
I don't believe you need any particular feature set.
Also, this is a 'Contact Center' forum - you would get more responses in other places.
Regards
Aaron HarrisonPrincipal Engineer at Logicalis UK
Please rate helpful posts...

Similar Messages

How many numbers of GRE Tunnels are supported on Cisco 3925 router?

Hi...
I would like to know that.......
How many numbers of GRE Tunnels are supported on Cisco 3925 router?
Thanks....

This is what I found in my search:
There may be factors such as memory constraints that will place practical limits on how many tunnels you can support. But there is also a hard limit on the number of tunnels that you can configure. That limit is based on the limitation of the number of IDBs supported by your router. The IDB is the Interface Descriptor Block and each interface (physical, or tunnel, or loopback, or whatever) requires an IDB. The number of IDBs will vary by platform and sometimes by release level of the code that you are running. You can use the privileged command show idb to see what the limitation is on your router. On the 1841 router that I just checked the limit on IDB is 1200 (which is a pretty large number - I believe that you would encounter other limits on performance or on size of configuration before you exhaust the IDB limit).
https://supportforums.cisco.com/thread/2007932
Hope it helps.
Jatin Katyal
- Do rate helpful posts -

Cisco 3925 router with an ATM E3 card that never goes down!

Hi all,
We a Cisco 3925 router with an ATM E3 card (NM-1A-T3/E3) configured as below with 1 PVC. we see that the ATM subinterface we created for the PVC never goes down! not even when the WAN link is down! The problem with this is we are tracking the line protocol of the ATM sub interface to have VRRP failover to standby router. But because of this issue only BGP goes down whenever the WAN is down & line-protocol of the Subinterface remains up, the failover never happens & site is down. We can configure VRRP to track reachability of a BGP route as workaround but I would like an explanation or troubleshooting steps to check whats the trouble with current setup?
Cisco IOS Software, C3900 Software (C3900-UNIVERSALK9-M), Version 15.1(2)T4.1, MAINTENANCE INTERIM SOFTWARE
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 30-Aug-11 08:44 by prod_rel_team
card type e3 1
interface ATM1/0
description Link to PE
mtu 1500
bandwidth 34010
no ip address
no ip proxy-arp
logging event subif-link-status
no atm ilmi-keepalive
no atm enable-ilmi-trap
end
interface ATM1/0.101 point-to-point
description PVC to MPLS PE
mtu 1500
bandwidth 2500
ip address a.b.c.d 255.255.255.252
no ip proxy-arp
ip flow monitor FMforIP4in sampler ata1to100 input
ip flow monitor FMforIP4out sampler ata1to100 output
ip nat outside
ip virtual-reassembly in
no atm enable-ilmi-trap
snmp trap link-status
pvc 1/101
vbr-nrt 8192 8192 1
vc-hold-queue 2048
oam-pvc manage
oam retry 3 5 1
oam ais-rdi 15 3
encapsulation aal5snap
protocol ip inarp
queue-depth 5 3
service-policy out Edge_Queueing
end
Thanks a lot in advance!

Your router has some configuration on it already and it would help us give you better advice if we knew what is already in the configuration. So would you post the output of show running-config (if there is sensitive information like addresses and passwords you can mask them out.
Changing the configuration register was a good start. I have a couple questions/observations that may help you get started. I notice what appears to be the same public IP address on Gig0/0 and on multilink. Did you get that address from your ISP? If so what kind of connection do you have to the ISP?
In your description you tell us that Gig0/0 is connected to a small switch, which I assume is for the LAN of your network. But that also is the interface where the public address is configured. So I am confused whether this interface is for LAN or for connecting to the ISP. Can you clarify this?
HTH
Rick

Configuration Issue with my Cisco 871 Router

Hi all,
I am a newbie to the Cisco IOS.
I got a Cisco 871 Router that I'd like to use for internet connection. My LAN network is 192.168.1.0/24 and the ISP has assigned us the IP 41.212.79.108/24 and gateway 41.212.79.1.
With my current configuration, I can hit the router - 192.168.1.1 - and it's WAN port - 41.212.79.108 - but not the gateway.
Below is my current config:
Hoggers#show config
Using 4414 out of 131072 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Hoggers
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
enable secret 5 **********************.
no aaa new-model
crypto pki trustpoint TP-self-signed-568493463
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-568493463
revocation-check none
rsakeypair TP-self-signed-568493463
crypto pki certificate chain TP-self-signed-568493463
certificate self-signed 01 nvram:IOS-Self-Sig#7.cer
dot11 syslog
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.10.1
ip dhcp excluded-address 192.168.1.1
ip dhcp excluded-address 192.168.1.2
ip dhcp excluded-address 192.168.1.3
ip dhcp excluded-address 192.168.1.4
ip dhcp excluded-address 192.168.1.5
ip dhcp excluded-address 192.168.1.6
ip dhcp excluded-address 192.168.1.7
ip dhcp excluded-address 192.168.1.8
ip dhcp excluded-address 192.168.1.9
ip dhcp excluded-address 192.168.1.10
ip dhcp excluded-address 192.168.1.100
ip dhcp excluded-address 192.168.1.90
ip dhcp pool ccp-pool
   import all
   network 10.10.10.0 255.255.255.248
   default-router 10.10.10.1
   lease 0 2
ip dhcp pool LANPOOL
   network 192.168.1.0 255.255.255.0
   default-router 192.168.1.1
   dns-server 41.212.3.2 41.212.3.253
ip domain name yourdomain.com
ip name-server 41.212.3.2
ip name-server 41.212.3.253
archive
log config
hidekeys
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface FastEthernet4
description Wan to Outside World
ip address 41.212.79.108 255.255.255.0
duplex auto
speed auto
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
ip address 192.168.1.1 255.255.255.0
ip tcp adjust-mss 1452
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 41.212.79.1
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip dns server
ip nat inside source static tcp 192.168.1.31 80 interface FastEthernet4 80
access-list 23 permit 10.10.10.0 0.0.0.7
no cdp run
control-plane
scheduler max-task-time 5000
end
I'll appreciate any light you can shed on what am missing.

2 wireless routers can not communicate wirelessly with each other.
You need to connect cable between 2 routers and use the second wireless router as access point.
Follow this link to connect Linksys router to another router.
Some of your devices are getting same IP address. This might be the issue with DHCP server of the router. You can try DHCP reservation on the router so that each device will get unique IP address.

Configuring QoS on Cisco 3845 router for Polycom Video Conferecing

Dear All,
We have implemented a Polycom Video Conferecing solution at our Head Office. Using this we communicate with other branch offices through WAN (2mbps, MPLS).
The problem is that this WAN link is also used for data. When the traffic is high on the link, the voice and the video quality goes down drastically and we experience connection drops.
At the moment we have configured our Polycom box to communicate at 512kbps speed and we would like to reserve it in our WAN link. In case, video conferencing is not happening we would like it to be utilised by other traffic.
Can we configure QoS on our Cisco 3845 router to do this? I'm not a Cisco expert and have pressures from Management to correct this before the next conference.
I have already googled a fair bit but couldn't find something for me.
Could someone please tell me the exact commands that need to be given on our router to achieve this.
I'll be very thankful for this help.
Best Regards.

Hi,
You can use something like the following to guarantee 5122k of bandwidth to your video-conferencing bandwidth but to allow that bandwidth to be used by other traffic when it is not being used for video-conferencing:
class-map VDOConf
match ip dscp af41
policy-map WANPolicy
class VDOConf
bandwidth 512
interface
service-policy output WANPolicy
Note that the above assumes that your video conferencing traffic is being marked to AF41. If that is not the case, you can always match on the IP address of your polycom device using an ACL:
class-map VDOConf
match access-group 101
access-list 101 permit ip .....
Hope that helps - pls rate the post if it does.
Paresh

Cisco 3925 Enhanced EtherSwitch Service Module

Hello all,
I have a Cisco 3925 router with a SM-ES3G-16-P Etherswitch module. In order for me to access it, I need to put an IP address on the phyiscal interface its attached to. Then I can access it via the service-module command.
My question is -- does it matter what address I give it? Does it need to be a legitimate management address on my network so that I can access it directly from another switch? Or do I always need to go through the router and issue the service-module command? If I do need to always go through the router, I should just be able to give it a 10.10.10.1 address and that should be enough, right?
Thanks for your help in advance,
Bobby Grewal

Thanks Reza...one more question. how does the switch module actually talk to the 3925 router? Through port 17 or 18? If so, do I need to configure those interfaces as routed ports within the same subnet? Or are they just trunks? All connections within the switching module would need to talk to outside devices.

Sm32-a in Cisco 3925 terminal server

Hi,
I have a SM-32A module installed in slot 1 in a Cisco 3925 router to act as a terminal server providing reverse telnet sessions to various other device console ports. My understanding is that the ports on the SM-32A are referenced as "slot/port" - in my case 1/0-31. The terminal server L0 address is 100.1.1.1 What I cannot determine is do I need to configure an ip host table with conventional port numbers to facilitate connections e.g.
ip host R 2000 100.1.1.1
ip host R1 2001 100.1.1.1
ip host R3 2003 100.1.1.1
ip host R31 2031 100.1.1.1
If so, are the port numbers 2000 to 2031 or is another convention used?
Many thanks.
Ed

Duplicate posts.
Go here: https://supportforums.cisco.com/discussion/12213596/sm32-cisco-3925-terminal-server

I am loosing configuration when I power off my Cisco 857 router

I bought new Cisco 857 router from the shop. Router must have been used before as I couln't go in with default username/password cisco/cisco.
Well I followed instruciton and reset password to username and password. Now I finally connected to the Cisco CP express over my IE browser.
I found out that somebody was using a router from the shop so this is why I coun't log to it in the first place. Anyway problem is that when I changed configuration and applied settings it remembers it until I power it off. When I power it on again it remembers all settings from that shop.
It reverts everything back: IP address, previous level 15 account and password - everything like after password reset.
I tried it again and it again lost settings. So I found following instruction:
http://www.cisco.com/en/US/products/hw/routers/ps233/products_tech_note09186a00800a65a5.shtml
I followed it and changed again all settings on the router. My settings are again lost after power off/on. I noticed that when I do first bit it does show
0x2102 not 0x2142 like they think that is password reset mode.
Here is my output from Hyper Terminal:
=============================
Cisco#enableCisco#show startUsing 3359 out of 131072 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Cisco!boot-start-markerboot-end-marker!logging buffered 51200 warningsenable secret 5 $1$hpKF$Rc1tl6r45J8iHG7EN5jSk.!no aaa new-model!crypto pki trustpoint TP-self-signed-3185909327 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-3185909327 revocation-check none rsakeypair TP-self-signed-3185909327!!crypto pki certificate chain TP-self-signed-3185909327 certificate self-signed 01 nvram:IOS-Self-Sig#5.cerdot11 syslogno ip dhcp use vrf connectedip dhcp excluded-address 10.10.10.1!ip dhcp pool ccp-pool   import all   network 10.10.10.0 255.255.255.248   default-router 10.10.10.1   lease 0 2!!ip cefno ip domain lookupip domain name molinary.com!!!username admin privilege 15 secret 5 $1$jD3j$r6ROikgGsIlcMTGjkxFQ6.username username privilege 15 password 0 password!!archive log config hidekeys!!!!!interface ATM0 no ip address shutdown no atm ilmi-keepalive dsl operating-mode auto!interface ATM0.1 point-to-point description $ES_WAN$ ip nat outside ip virtual-reassembly pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 !!interface FastEthernet0!interface FastEthernet1!interface FastEthernet2!interface FastEthernet3!interface Vlan1 description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$ ip address 10.10.10.1 255.255.255.248 ip nat inside ip virtual-reassembly ip tcp adjust-mss 1452!interface Dialer0 ip address dhcp encapsulation ppp dialer pool 1 dialer-group 1 no cdp enable ppp authentication chap pap callin ppp chap hostname [email protected] ppp chap password 0 netgear01 ppp pap sent-username [email protected] password 0 netgear01!ip forward-protocol nd!ip http serverip http access-class 23ip http authentication localip http secure-serverip http timeout-policy idle 60 life 86400 requests 10000ip nat inside source list 1 interface ATM0.1 overload!access-list 1 remark INSIDE_IF=Vlan1access-list 1 remark CCP_ACL Category=2access-list 1 permit 10.10.10.0 0.0.0.7dialer-list 1 protocol ip permitno cdp run!control-plane!banner exec ^C% Password expiration warning.-----------------------------------------------------------------------Cisco Configuration Professional (Cisco CP) is installed on this deviceand it provides the default username "cisco" for one-time use. If you havealready used the username "cisco" to login to the router and your IOS imagesupports the "one-time" user option, then this username has already expired.You will not be able to login to the router with this username after you exitthis session.It is strongly suggested that you create a new username with a privilege levelof 15 using the following command.username <myuser> privilege 15 secret 0 <mypassword>Replace <myuser> and <mypassword> with the username and password youwant to use.-----------------------------------------------------------------------^Cbanner login ^CAuthorized access only! Disconnect IMMEDIATELY if you are not an authorized user!^C!line con 0 login local no modem enableline aux 0line vty 0 4 privilege level 15 login local transport input telnet ssh!scheduler max-task-time 5000endCisco#Cisco#Cisco#Cisco#Cisco#Cisco#Cisco#Cisco#Cisco#show versionCisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, RELEASE SOFTWARE (fc3)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 22-Jan-10 14:46 by prod_rel_teamROM: System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARECisco uptime is 20 minutesSystem returned to ROM by power-onSystem image file is "flash:c850-advsecurityk9-mz.124-15.T12.bin"This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.A summary of U.S. laws governing Cisco cryptographic products may be found at:http://www.cisco.com/wwl/export/crypto/tool/stqrg.htmlIf you require further assistance please contact us by sending email [email protected] 857 (MPC8272) processor (revision 0x400) with 59392K/6144K bytes of memory.Processor board ID FCZ140792J5MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x104 FastEthernet interfaces1 ATM interface128K bytes of non-volatile configuration memory.20480K bytes of processor board System flash (Intel Strataflash)Configuration register is 0x2102Cisco#Cisco#Cisco#Cisco#endTranslating "end"% Unknown command or computer name, or unable to find computer addressCisco#reloadProceed with reload? [confirm]*Mar 1 01:19:27.786: %SYS-5-RELOAD: Reload requested by username on console. Reload Reason: Reload Command.System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARETechnical Support: http://www.cisco.com/techsupportCopyright (c) 2006 by cisco Systems, Inc.C850 series (Board ID: 2-149) platform with 65536 Kbytes of main memoryBooting flash:/c850-advsecurityk9-mz.124-15.T12.binSelf decompressing the image : ############################################## [OK]              Restricted Rights LegendUse, duplication, or disclosure by the Government issubject to restrictions as set forth in subparagraph(c) of the Commercial Computer Software - RestrictedRights clause at FAR sec. 52.227-19 and subparagraph(c) (1) (ii) of the Rights in Technical Data and ComputerSoftware clause at DFARS sec. 252.227-7013.           cisco Systems, Inc.           170 West Tasman Drive           San Jose, California 95134-1706Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, RELEASE SOFTWARE (fc3)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 22-Jan-10 14:46 by prod_rel_teamImage text-base: 0x8002007C, data-base: 0x814E7240This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.A summary of U.S. laws governing Cisco cryptographic products may be found at:http://www.cisco.com/wwl/export/crypto/tool/stqrg.htmlIf you require further assistance please contact us by sending email [email protected] 857 (MPC8272) processor (revision 0x400) with 59392K/6144K bytes of memory.Processor board ID FCZ140792J5MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x104 FastEthernet interfaces1 ATM interface128K bytes of non-volatile configuration memory.20480K bytes of processor board System flash (Intel Strataflash)no ip dhcp use vrf connected               ^% Invalid input detected at '^' marker.SETUP: new interface NVI0 placed in "shutdown" statePress RETURN to get started!*Mar 1 00:00:03.952: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Initialized*Mar 1 00:00:03.960: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Enabled*Mar 1 00:00:07.244: %LINK-3-UPDOWN: Interface FastEthernet0, changed state toup*Mar 1 00:00:08.413: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up*Mar 1 00:00:08.821: %SYS-5-CONFIG_I: Configured from memory by console*Mar 1 01:19:27.072: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up*Mar 1 01:19:27.352: %SYS-5-RESTART: System restarted --Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, RELEASE SOFTWARE (fc3)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 22-Jan-10 14:46 by prod_rel_team*Mar 1 01:19:27.352: %SNMP-5-COLDSTART: SNMP agent on host Cisco is undergoinga cold start*Mar 1 01:19:27.436: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF*Mar 1 01:19:27.436: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF*Mar 1 01:19:27.540: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, changed state to down*Mar 1 01:19:28.072: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up*Mar 1 01:19:28.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up*Mar 1 01:19:28.484: %LINK-5-CHANGED: Interface ATM0, changed state to administratively down*Mar 1 01:19:28.848: %LINK-5-CHANGED: Interface NVI0, changed state to administratively down*Mar 1 01:19:28.932: %LINK-3-UPDOWN: Interface FastEthernet3, changed state toup*Mar 1 01:19:28.936: %LINK-3-UPDOWN: Interface FastEthernet2, changed state toup*Mar 1 01:19:28.940: %LINK-3-UPDOWN: Interface FastEthernet1, changed state toup*Mar 1 01:19:29.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to down*Mar 1 01:19:29.932: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet3, changed state to down*Mar 1 01:19:29.936: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet2, changed state to down*Mar 1 01:19:29.940: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1, changed state to down*Mar 1 01:19:29.948: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to upAuthorized access only!===========================================
Please help me as I am stuck and can't go any further....

Hi David White,
Alternatively, after password recovery you can modify the configuration to be what you want, and then issue:
   write memory
to save the configuration. You can then verify that your changes have been saved to the startup config by issuing:
   show startup-config"
The only good thing is that when I switch off a router it erase configuration except my new password which I created after password reset. Everything else is getting vanished (ADSL settings, DHCP, routing ) everything. Even new admin accounts I created.
Well have a question to your above comments. I am new in Cisco so please put as much detail as you can for me to understand. When you say modify configuration do you mean to go to Cisco CP Express graphical interface and then connect router to hyper terminal and execute above commands?
Why router doesn't remember this anyway. There must be some option to change in configuration to make thing permanent when I hit apply changes in Cisco CO Express otherwise it is pointless to heve it.
Phillip
write memory
is
copy running-config startup-config"
Can't this be done via Cisco CP Express or set up router to copy this every time I change this in graphical interface rather going to command line to achnoledge it?
I understand your concern about this router and somebodie's configuration details as you want things to be un-used when you buy them - true. ADSL details belongs to the shop which sold me the router so that is why I don't make a big problem about this. We take most of hardware from this shop and have discount and many good deals with them so I think they have been just testing it and forgot to erease their config. It might be that someone has returned router to the shop and they have repaired it and tested it.
I hope this is a normal behaviour of this router as I have option to replace it in case this is a fault.
Could you please write me step by step guide how can I make changed options stay permanently on router?
thank you
Dragan

Configuring Cisco 3620 router

I am quite new and haven't worked before with Cisco router. I have a Cisco 3620 router with only one ethernet interface (FastEthernet 0/0).
I want to configure it so that the router will have ip address of 192.168.2.2 (255.255.255.0). I am not using DHCP so all the machines in the network are configured manually.
My running-config is as follows.
version 11.3
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname router
enable secret xxxx
enable password xxxx
controller T1 0/0
framing esf
linecode b8zs
channel-group 0 timeslots 1-24 speed 64
interface FastEthernet0/0
ip address 192.168.2.2 255.255.255.0
interface Serial0/0:0
no ip address
shutdown
ip classless
dialer-list 1 protocol ip permit
dialer-list 1 protocol ipx permit
line con 0
line aux 0
line vty 0 4
password xxxx
login
end
Can someone give advise on what should I use for default-gateway, default-network and route?
I want to use name-server which has class B ip address. 131.x.x.x.
If my router can route all the traffic to 131.x.x.y (gateway in the same LAN as router) then I can connect to Internet.
Can someone tell me how to do this?
Regards,
Amar.

Hi
i feel u need to have 2 ethernet interfaces in your router to have the reachability to the 131.x.x.x series from your local lan which is in 192.168.2.x series..
eventually u need to deploy nat to have this kinda access in place...
if you got to have that you can configure one of your interface on 131.x.x.x series and configure it as a nat outside interface and keep faeth0/0 as ur inside interface.
you need to configure up a access list and also the necessary overloading to achieve the connectivity.
i think this link will def help u out to find more details about the scenario and config details about which i m mentionining over here..
http://www.cisco.com/en/US/tech/tk648/tk361/technologies_tech_note09186a0080094831.shtml
And again you can have the ip reachability using normal static ip route in your box..pointing to the ip which can be used to go out to the public/outside world..
regds

Cisco works LMS 3.0.1 does not archiever configuration for cisco 7201 router

Hi All,
We have Cisco works LMS 3.0.1 and it does not archiever configuration for cisco 7201 router.
Any help would be appriciated.
Thanks in advance
Samir

Hi,
*** Device Details for d0151-100 ***
Protocol ==> Unknown / Not Applicable
Selected Protocols with order ==> TFTP,SSH,HTTPS
Execution Result:
Unable to get results of job execution for device. Retry the job after increasing the job result wait time using the option:Resource Manager Essentials -> Admin -> Config Mgmt -> Archive Mgmt ->Fetch Settings
This is the error while doing syn archieve.
I am not sure about Rtr7000 version but we have latest Rtr7000.
Waiting for your kind reply.
Samir

What's "SAVE" configuration command for Cisco switch/ router?

What's "SAVE" configuration command for Cisco switch / router? I know Switch#copy running-config startup-config works well,
but so long, any other command that easy to remenber?

What's "SAVE" configuration command for Cisco switch / router? I know Switch#copy running-config startup-config works well, but so long,
any other command that easy to remenber?
yes, here: Switch#write,and want to know more about the Cisco switch, please visit:http://www.3anetwork.com/cisco-switches-price_c1

Still trying to configure a Cisco 877W router

Hi,
I am still unable to configure my Cisco 877W router for use on a B.T. ADSL phone line.
I can log in to the router which starts up the SDM Express. I then select the wizard and get as far as filling in the DHCP server configuration.
When I then press next it does not go to the next step, it just stays on the DHCP config screen. I am now using a Windows XP machine to configure the router as someone suggested, but it continues to halt at the same place.
Can anyone help please,
Thanks.
Dave.

Hi. You may check out the topics in this link instead.

Cisco 831 Router to Configure VPN Access

Hello,
I need assistance in configuring a VPN in a Cisco 831 Router. I do not have any experience in configuring routers and VPN's, and would appreciate if any one could help out.
I would like to connect three Laptops to the Cisco 831 via Cisco VPN Client. Three laptops must have 10.42.6.x Address assigned by the router on the VPN Connection. They will also need access to the internal network which is 192.168.x.x private network. The Cisco has a Static IP on the Internal Interface and External Interface. I have tried several different ways of doing this, however I must be doing something wrong in my config.
Any help or suggestions would be appreciated.

Hi Robert
You can refer the below link in finding out the exact config to start with.
do make sure that your Cisco 831 box with the current IOS code installed in it supports the required feature to run the same..
http://www.cisco.com/en/US/tech/tk583/tk372/tech_configuration_examples_list.html#anchor16
regds

Configuration of cisco 3662 router

i want to connect 3662 router to cisco 1700 router
how to configure the 2 router ?
what are the commands using?
meaning of each commands?

What sort of interface(s) are you using to connect these two routers ? The commands used will depend on that...
Paresh

I have a Cisco wireless router. Can I buy an Airport Express plug in booster for a distant part of my house or do I need an Airport Extreme base station instead to make the Airport Express plug in booster work?

Can I buy an Airport Express plug-in wifi signal booster to connect to a Cisco wireless router, or do I have to buy an Airport Extreme base station to make the Airport Express plug-in work?

You would need either an AirPort Extreme or an AirPort Express connected to the Cisco router, with a permanent Ethernet cable connection.
Configure the Extreme or Express that is connected to the Cisco router to "create a wireless network".
Then, you could add an AirPort Express to "extend a wireless network" to provide more wireless coverage for the network that the Extreme or Express would be creating.
Remember that the Express can only "extend" the quality of signal that it receives, so it must be located where it can receive a strong signal from the "main" AirPort.
If you don't need the Cisco wireless signal, you could turn it off.....or use that network for guests or something similar.
The bottom line here......you always need two Apple routers if you want to extend the network wirelessly.

Configuring IP SLA in cisco 3925 router.

Similar Messages

Maybe you are looking for