Configuring Paging system to interface with an FXO port

Hello
Wanted to see if there is some good documentation on configuring my fxo port on my gateway to interface with a paging system?
Thank you for your help

Hi Joseph,
It really depends on the type of overhead paging system you're intending to use. The documentation for the paging system being used usually specifies exactly what type of circuit is required.
Kind regards,
Craig

Similar Messages

Need a sample cme with multiple fxo ports, hunt fashion

hi,
anyone kind enough to provide a sample working configuration of multiple fxo ports (each being a pstn line) and I assuming the telco is doing hunting...
so let's say 4 lines, if line 1 is busy the call is sent by the telco on line 2 and so on...
incoming and outgoing.
thank you very much!!
I did google it and can't find anything with multiple fxo ports.

trunk group 1
max-calls voice 4 (or however many POTS lines you want to use)
hunt-scheme round-robin (or whatever method you like)
voice-port 0/0/0
trunk-group 1
connection plar opx XXXX (extension)
caller-id enable
voice-port 0/0/1
trunk-group 1
connection plar opx XXXX
caller-id enable
voice-port 0/0/2
trunk-group 1
connection plar opx XXXX
caller-id enable
voice-port 0/0/3
trunk-group 1
connection plar opx XXXX
caller-id enable
dial-peer voice 1 pots ( I like creating this for troubleshooting, by default cisco router accept incoming calls)
trunkgroup 1
incoming called-number .
direct-inward-dial
dial-peer voice 2 pots
trunkgroup 1
destination-pattern 8[2-9]...... (8 for an outside line or 9 or nothing, then adjust your forward-digits to match)
forward-digits 7
dial-peer voice 3 pots
trunkgroup 1
destination-pattern 81[2-9]..[2-9]......
forward-digits 11
dial-peer voice 4 pots
trunkgroup 1
destination-pattern 8911
forward-digits 3
dial-peer voice 5 pots
trunkgroup 1
destination-pattern 911
forward-digits 3

CAPA System (CATSWEB) Interface with SAP

Hi Experts
Anybody worked on SAP interface with CATSWEB software (for CAPA system)?
Please guide me to do the same.
Thanks in advance.
Regards
Bala

Hi JJ,
I may be just re-iterating what has already been said, but for clarity I will put down the points again, since I was also faced with the same confusion regarding how barcode and sap will work.
1. Barcode Scanner has nothing to do with SAP or any software.
   In simple terms, it is just like a keyboard. To demo;
    a) Plug in the barcode scanner in the USB port
    b) Open Notepad in windows
    c) The cursor will be inside the notepad
    d) Now scan the bar code against any barcode image.
          (Suppose the barcode image contains the information XYZABC)
   e) As soon as you scan, the characters   X Y Z A B C (without spaces)
      will AUTOMATICALLY GET TYPED on the screen, inside the notepad, at the place of cursor.
    Hence, the SCANNER just acts as a KEYBOARD.
   and autommatically types in the characters WHEREVER the CURSOR is.
   We can test this using notepad, Excel, word or any where the cursor can appear.
   We can test in any standard sap screen on any text field also, etc.
2. Saving the data in SAP.
    a) First we have to figure out how to save data in SAP,
        considering we are entering data MANUALLY.
   b) This can be a STANDARD Transaction or a Z transaction.
   c) Suppose the field / information is material number,
     then instead of TYPING the material number on the screen, in the field,
    we simply place the cursor on that field.
d) then we simply scan the image (containing information on material n umber) and hooooooray,
    it gets automatically TYPED IN on that field.
    Thats it. Other fields we may have to enter manually and press the SAVE button to save the data.
Scanner just saves TYPING the information manually, and hence reduces time and error both.
Hope this helps.
Regards,
Amit Mittal.

Link PBX systems E1 interface with router

The interface is E1 for PBXs, with QSIG ?
I want to make less 10 simultaneous calls. What WIC, VIC or VWIC modules and codecs should be used with router 2801 / 2811
Thanks.

Already answered at:
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Service%20Providers&topic=Voice%20over%20IP&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1ddefb93

Issue connecting SPA3102 FXO port to paging interface

Hello,
I was referred to this community after a call to small business support, we were unable to come to a solution.
SPA3102 v5.2.13 FW
Viking Electronics PI-1 Paging Interface
We were told from Viking that the interface only supports an FXO port, all the connections were verified with their support and we're able to page by connecting an analog phone straight to the interface. Plugging into the FXS port on the SPA3102 also results in a dial tone playing over the paging system.
All settings on the SPA3102 are default minus SIP registration information, we see the unit as registered within the web interface as well as within our Asterisk CLI.
Trying to ring the extension results in constant ringing if voicemail is disabled, and straight to voicemail if enabled. Within the Asterisk CLI we see a SIP response 503 "Service Unavailable."
I can get the SPA3102 to respond by lowering the "Line In Use Voltage" down from its default value of 30. However all I hear is a hum and I'm not able to speak over the paging system.
Any insight into this issue would be greatly appreciated, we believe it's just settings on the SPA3102 unit itself that need to be changed.
Thanks!

Looking at the Viking Pl-1 web page installation instructions, I think the key setting on the SPA3102 would be to set the voip-to-pstn gateway dial plan to NONE. The "hum" you get when you lower the Line-In-Use setting sounds like the dial tone you would get with the default dial plan setting.
I would try the following:
Viking Pl-1:
Talk Battery Switch (PT): On
Audio In: Cabled to FXO port of SPA3102
SPA3102:
Interface Analog Phone attached to SPA3102:
Line 1 Tab
Line Enable: YES
Dial Plan: (S0<:@gw0>)
PSTN Line Tab
Line Enable: Yes
VoIP-to-PSTN Gateway Enable: Yes
One Stage Dialing: Yes
Line 1 VoIP Caller DP: NONE
VoIP Answer Delay: 0
Line In Use Voltage: xx
The Line In Use Voltage needs to be lower than the Talk Battery voltage supplied by the Viking Pl-1. Usually it is set about half way between the on-hook and off-hook voltage level. Measure the FXO (PSTN Line) on-hook voltage by reading it on the SPA3102 INFO Tab. Set the Line In Use Voltage substantially below the on-hook talk voltage.
If you lift the phone with the above settings you should be connected to the paging system.
Interface to an asterisk pbx system:
PSTN Line Tab
Setup Registration on PSTN Line Tab to Asterisk system.
Register: Yes
Proxy: xxx
UserID: xxx
Password: xxx
VoIP-to-PSTN Gateway Enable: Yes
VoIP Caller Auth Method: None
One Stage Dialing: Yes
VoIP Caller Default DP: NONE
VoIP Answer Delay: 0
Line In Use Voltage: same comments as above
If you call the extension on the asterisk PBX you should be attached to the Viking unit.

QM interface with WM

Hi Gurus,
I Have a situation where transfer orders are generating based on the storage bin capacity.
For example: when i used GR quantity 3000 LBs, TO is not generated and when i changed the quantity to 1000Lbs TO is generated.
I believe, it has something to do with the Storage bin capacity. Please advice.
We had an issue before when QM views were activated, TO's are not generated. So i made a configuration changes in WM interface with QM and moved to Production client, now we are having this problem.
Your suggestions are highly appreciated.
Thanks,
Quantum.

Hi Anand Rao,
Thanks for showing interest on my issue.
Configurations i have done QM interface with WM are given below.
Logistics execution -> WarehouseManagement-> Interface->Qualitymanagement->Define Inspection sample Control
Here i maintained Quality control to the Warehouse number.
Logistics execution -> WarehouseManagement-> Interface->Qualitymanagement->Activate QM interim storage type search
Here i assigned Quality control indicators to the warehouce no. and storage type combination.
I believe my issue is not related to the above configuration. It has something to do with the storage bin capacity.
Please feel free to let me know, if you need further information.
Thanks,
Naveen.

Configuring IDSM-2 Promiscuous Mode with MLS IP IDS

I am having a problem configuring promiscuous mode with an IDSM-2 running 5.0(3)S181.0 in a 6509 with Sup 720 running IOS 12.2(18)SXD4. I am running router interfaces without VLANs so I have created an extended access list with a 'permit ip any any' and configured this on my interfaces with 'mls ip ids access-list-name'. I configured 'intrusion-detection module x data-port 1 capture' and 'intrusion-detection module x data-port 2 capture', and because of the caution note on page 14-12 of 78-16127-01 I also configured 'intrusion-detection module x data-port 1 capture allowed-vlan 1-4094' and 'intrusion-detection module x data-port 2 capture allowed-vlan 1-4094'. After that I can see the output counters rising in 'show 'intrusion-detection module x data-port 1 traffic' and 'show 'intrusion-detection module x data-port 2 traffic'. I can configure the IDSM-2 using the VMS management center, and I added my sensor to security monitor and set the level down to informational, but I don't even see any events or even the start-up informational message. Anyone have any idea what I missed?

Here is a document on Configuring the Catalyst Series 6500 Switch for IDSM-2 in Promiscuous Mode.
http://www.cisco.com/en/US/products/sw/secursw/ps2113/products_configuration_guide_chapter09186a0080459221.html#wp1030752

3825 FXO Port remains in off-hook after call

Hello,
I have a 3825 router with 8 FXO ports running Cisco IOS Software, 3800 Software (C3825-SPSERVICESK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2). The problem we are facing is that after a call is placed through any of the FXO ports and the call is ended by the user, the port remains in off-hook till a reset of the port is done or someone restarts the router. Only then is the port accessible again.
I am thinking of changing the cards, but i do not want to invest in replacing the cards and then find out that this doesnt solve the problem.
The wierd thing is that this issue started on its own accord not too long ago.
Comments and suggestions please!
Regards,
Femi

Hello,
I do not want to change the FXO card till I am sure that is the problem and I did state that I always have to reboot the router when the problem starts. Rebooting clears the problem but it is back immediately I attempt a call again and hang up that call.
I have timeouts call-disconnect already configured, see below:
voice-port 0/0/0
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/0/1
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 2626878
caller-id enable type 1
voice-port 0/0/2
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/0/3
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/0
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/1
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/2
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/3
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
Regards,
Femi

Grouping FXO Ports

Hello all ,
I am setting up a CUCM with an h323 gateway that only has multiple FXO ports . I am looking for a method to group FXO ports and by grouping I don't just mean to group them with a trunk group but I need to use "for example" 4 ports for specific users and and other 4 or more ports for others .
what is the workaround for this ..
Thanks

or let's make it simple...
Have a duplicate router patterns in different partitions for desired group of users and assign CSS accordingly.
Have separate route list for desired group of users.
Apply called party digit manipulation at each route list level and add different prefix to called party. Say 8 to group 1 and 9 to other.
At gateway, have separate destination-patterns (under dialpeer) for prefix 8 and 9 with desired FXO ports assigned to dialpeer.

SAP Inventory management interface with Third party Warehouse System

Hi Experts,
Need your input for designing the SAP solution with existing Third party warehouse system ( Exacta ):-
SAP ERP will be implemented for all locations of Client ( SAP MM, FI, PS , HR etc ).The Client has 10 distribution centres which are on Exacta Warehouse systems and will be linked with SAP Inventory management system.
The way it will work - Goods receipt will always happen in SAP for all locations and then interface needs to Trigger subsequent Putaway activities at Exacta Ware house ( third party warehouse system) for those 10 locations.
Goods Issue for these locations will happen from Exacta and then update will be posted in SAP via interface.
All locations will be created as Plant /Storage locations in SAP.
Need your inputs what special configurations need to happen in SAP for those locations so that goods receipt in SAP can trigger putaway activities in Exacta system .
Do we need to do configuration for decentralised Warehouse in SAP for handling this?
Pl. give your inputs based on your past experience where you handled such scenarios via interface with SAP Inventory management and legacy warehouse systems.
Thanks for quick response on this.
Regards,
Krish

Krish
This is a std business process where clients have used their existing warehousing systems but implemented SAP forother functions such as Order entry, inventory mgmt and procurement, financials.
The typical interface that needs to happen is
1. Sales order ( and or delivery)
2. Invetory needs to be passed to the WH. Typically people send it when SAP GR takes place.
3. When WH system does picking, it sends signal to SAP which then does PGI for the sales order delivery and that takes the stock out of the system.
Material master has to be transferred or mapped between two systems. Also, other elements need to be mapped between two systems.
The way I have seen this happening is :
you have an output on the SAP GR process. That creates an idoc to the WH system. Based on the capabilities of the WH system, it then does appropriate actions in the system.
Many times, middlewares are used to translate/ map the data between SAP and the WH systems.
So system wise, there is ALE setup that needs to take place for IDOC creations.
Configuration and coding is required for the output type and the program behind it. There are several std FUnction Modules that can be used for this.
Hope this helps.
Mankai

EREC: Interfaces with Third Party Systems

Hello Experts,
Does anybody can provide me a list of third party systems with seamless interface with E-Recruiting (SAP Partner) for the following purposes below:
Resume Parsing
Background Check
Drug Screening
Posting in Multiple Job Boards
Thanks in advance!
Sivani

Resume mirror is used for resume parsing.
Regards,
Bharat

Testing CAD-Desktop interface with CAD-system

Hi,
does anybody know if it is possible to get a CAD-system for free to test the CAD-Desktop interface of SAP?
I am not a key CAD user, I just want to look how CAD Desktop works.
Regards,
Oliver

You do not need CAD system to work with CAD Desktop
call transaction SE37
In Function module enter : CDESK_SHOW
or CDESK_TEST
Fill the import paramenters
Execute it
CAD Desktop will appear

How to configure SolMan for interfacing with SAP Quality Center

Hello everyone,
Our company has only recently acquired and activated the permanent license for SAP Quality Center by HP. We would like QC to interface with SAP Solution Manager. My question is how to perform the configuration steps to make the interface work with Quality Center? I need to set up the IMG addon SM_QC_AD, which can be found under the transaction SPRO, but I need documentation on which steps to take and why.
I am often referred to SAP note 1059350 and/or the configuration guide, but these only say that I should configure the IMG but not how.
There is a SAP tutor available on the service marketplace, but I think it's rather uninformative.
Can I find better documentation elsewhere?

Hi ,
[Configuration Guide SAP adapter for SAP Quality Center by HP|https://websmp101.sap-ag.de/~sapdownload/011000358700000612662007E/Adapter_Configuration_.pdf] might be useful.
Check [Master guide|https://websmp201.sap-ag.de/~sapdownload/011000358700000612672007E/Adapter_Master_Guide.pdf] also.
Regards
Naveen
Edited by: Naveen kumar Palanichamy on Feb 19, 2009 6:38 AM

SAP Certification for *ABAP System Interfaces with SAP NetWeaver    7.0*

Hi Experts,
I am appearing for SAP Certification in the stream of *ABAP
System Interfaces with SAP NetWeaver    7.0*
so as per the syllabus i required the following material,
BC420,BC425, BC427,BC415,BC417,BIT300,BIT350
BC401,BC402,BC400, BC430,BC490,ADM325,BC425,NET900,
NW001,TESA20,TZCAFG,SM001
so if any body is having the softcopy or any related links of the
above mentioned material
please send to my following mail ID's.
<removed by moderator>
Points Assured.
Regards
Praneeth
Edited by: Jan Stallkamp on Oct 13, 2008 3:30 PM

Don't ask for copyrighted material!
Don't publish your e-mail address!
Don't assure points!
=> this thread will be locked.
Please read the rules of engagement otherwise you will set your account on risk of being deleted.
Best regards,
Jan Stallkamp

SAP Certification for   ABAP System Interfaces with SAP NetWeaver

Hi Experts,
I am appearing for SAP Certification in the stream of *ABAP
System Interfaces with SAP NetWeaver    7.0*
so as per the syllabus i required the following material,
BC420,BC425, BC427,BC415,BC417,BIT300,BIT350
BC401,BC402,BC400, BC430,BC490,ADM325,BC425,NET900,
NW001,TESA20,TZCAFG,SM001
so if any body is having the softcopy or any related links of the
above mentioned material
please send to my following mail ID's.
<removed by moderator> at yahoo dot co in
Points Assured.
Regards
Praneeth
<THREAD LOCKED. Please read the [Rules of Engagement|https://wiki.sdn.sap.com/wiki/display/HOME/RulesofEngagement] to discover why>
Edited by: Mike Pokraka on Oct 14, 2008 1:25 PM

Don't ask for copyrighted material!
Don't publish your e-mail address!
Don't assure points!
=> this thread will be locked.
Please read the rules of engagement otherwise you will set your account on risk of being deleted.
Best regards,
Jan Stallkamp

Configuring Paging system to interface with an FXO port

Similar Messages

Maybe you are looking for