Configuring PCMCIA Network Card 3Com 3CCFE574BT,3CCE589EC

Hi reader,
Have two PCMCIA cards 3Com, How do I install one this cards in Solaris 8 X86 or Sol 7 X86, Is possible install in my Acer TravelMate 507DX Not book
using the device configuration assistant software don't know my boards!
How do I now?
Wait one response, thanks
Marcio from Brazil/Ctba/PR

configure the following files manually and you should be good to go.
/etc/hosts
example
# Internet host table
127.0.0.1 localhost
192.168.1.104 hostname.domain.com hostname
/etc/netmasks
example
192.168.1.104 255.255.255.0
/etc/defaultrouter
example
192.168.1.1
/etc/hostname.iprb0
example
192.168.1.104
/etc/nodename
example
hostname.domain.com
Ofcourse substitute all the examples with your valid info.
Hope this helps....

Similar Messages

Looking for PCMCIA network card

I installed Solaris 8 on my laptop(Compaq Presario 1275),
and am looking for PCMCIA network card to configure
networks. Does anyone have Solaris 8 installed on
laptops and configured networks? If yes, what kind of
PCMCIA network card do you have for your laptop?
I plan to purchase a PCMCIA network card for my laptop?
Any recommendation, vendor, model name?
Thanks,

Soheil,
Just by adding more memory to your machine you can install RAC on your machine.You dont need two laptops.
http://www.oracle-base.com/articles/10g/OracleDB10gR2RACInstallationOnCentos4UsingVMware.php
Hope it helps

PCMCIA Network card for public network

Hi All
I am going to setup Oracle RAC on my laptops and would like to use PCMCIA netwrok card as public network, but I am wondering if it there would be any issue at all.
Could anybody advise please.
Thanks
Soheil

Soheil,
Just by adding more memory to your machine you can install RAC on your machine.You dont need two laptops.
http://www.oracle-base.com/articles/10g/OracleDB10gR2RACInstallationOnCentos4UsingVMware.php
Hope it helps

Dbconsole configuration - two network cards

Hi,
I have two network cards in the Solaris server and
Oracle 11g2 EE database server.
One network card is used for connection to the application (data network). Connection though standard port 1521.Database configured using server name defined for Net1 card and I can connect to the Oracle database using net1 card from apps server.
Second card is the management card (connected to the management network).
Is it possible to use it for connection to the dbconsole installed in the database ORACLE_HOME?
If yes, how I should configure dbconsole that I can see dbconsole web window through net2 card.
Thanks,
Oleg

Messy setup IMO, but anyway....
Your faulty resolv.conf is the reason you can't ping google. Edit it manually as required, and then use the -R flag in /etc/conf.d/dhcpcd to prevent it being overwritten. DHCP on both interfaces will probably cause routing issues as well, in which case you will need the -G flag.

Configure multiple network card with netcfg

Hello Archers! I am a happy new user of Arch Linux . I wanna say that your community is really great, thanks to all the people giving help out there.
My question is:
I must configure two eth interfaces, I have the both configured but sometimes I need to change configuration for connecting to other network that needs only one network card with other IP. I would like to select the configuration trough the "NET_PROFILES=menu" line in /etc/rc.conf or with the "netcfg" command but I don't know how to configure TWO interfaces in ONE profile of the /etc/network-profiles/* files?
Both networks have Static IP.
I search on the forums and do not find anything useful. I'm sorry if is there something in other post that I doesn't read.
Last edited by gooze (2007-02-01 07:00:26)

TuxLyn,
this netcfg profile works OK for me for a long time now:
CONNECTION="ethernet"
DESCRIPTION="Bridge: nVidia Corporation MCP55 Ethernet (rev a2)"
INTERFACE=eth1
#HOSTNAME="archabit64"
IP="dhcp"
DHCP_TIMEOUT=15
DHCP_OPTIONS="-C resolv.conf"
DHCLIENT=no
POST_UP="ip addr add 192.168.2.115/24 broadcast 192.168.2.255 dev eth1"
Of course, yours is more circunvoluted, but perhaps it helps.
ip addr outputs:
eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether 00:50:8d:9a:bc:2f brd ff:ff:ff:ff:ff:ff
inet 192.168.2.140/24 brd 192.168.2.255 scope global eth1
inet 192.168.2.115/24 brd 192.168.2.255 scope global secondary eth1
inet6 fe80::250:8dff:fe9a:bc2f/64 scope link
valid_lft forever preferred_lft forever
Mektub

Cannot configure External Network card

I cannot connect externel Network card to the system.OS cannot see the newly installed networkcard. My OS is SOlaris 10 x86 5/08. i tried different types of Network card Realtek,Datalink. Network Card number is D-Linkk DL10038C .Couldnt find any driver for this Network card that support for Solaris.
Can any one help me please....

Probably as stupid question but is there a way to export the driver from OpenSolaris to Solaris 10 as OpenSolaris supports the NIC?
By the way, I don't know if it matters but the info for my NIC on Solaris 10 appears both in */boot/solaris/devicedb/master* and */etc/driver_aliases*. It's just that the system doesn't detect it, when I run ifconfig -a it only lists the loopback interface.

Configure 2 network Card in Sun ULTRA 1

Hi,
Can I put 2 network card in a Sun Ultra 1
One Card it's for connected in my Network Sun in 192.9.XXX.XXX
and the second it's for my Network PC in 192.168.XXX.XXX
I want see this machine in the 2 network
Best regards.

This is caused by the default security policy which blocks file sharing with unidentified networks by making them public. (How it determines unidentified networks is another interesting question). To allow file sharing, you have to change the local
security policy to allow unidentified networks to be private.
Local Security Policy | Network List Manager Policies |Unidentified Networks
Bill

PCMCIA Network Card Drivers

I hope that this hasn't been posted already. I want to be able to use my Solaris 8 (intel) with my laptop computer. But I am having a devil of a time finding the drivers to make the Xircom RealPort Ethernet 10/100 (RE-100) NIC. The closest that I have found was the PCMCIA driver softwate from Lynnsoft for $100.00. I would sooner continue using Linux.Could someone please point me in the right direction. I have read the Hardware Compatability List, but to be homest, I just ended up confused. The PCMCIA entries that I found there and in the patch database did not give me the warm fuzzy that I was looking for before wiping out my HD to install Solaris 8 on and get on the Net. Any help would be greatly appreciated. Thanks in advance for the help and your patience.
Brgds,
[email protected]

Welcome to the Lenovo Community!
The factory update page only shows the diskette method (other systems also have an option to use the hard drive; typically this is called "non-diskette"). This thread:
http://forum.thinkpads.com/viewtopic.php?f=6&t=11244
appears to say that you can take a BIOS update floppy (created on a system which obviously has a floppy drive) and then use Nero to create a bootable copy on a CD. I have not personally tried this but it seems like it should work. Unless the BIOS updater checks to see if the media it's running off of is writable .
Also note that the BIOS update requires a working battery. However, there is a hack for that:
http://forum.thinkpads.com/viewtopic.php?f=6&t=782638
For about $10 you can get a 05K8874 floppy drive off of eBay and then you won't have to do this at all. In fact, if you get the external housing along with the floppy, you can basically have a three-spindle system; hard drive, Ultraslimbay CD drive and the external floppy. The floppy drive can be removed from the housing and installed in the Ultraslimbay if needed.
ref: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=220464800301
ref: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=290337648696
ref: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=390079970022 (2 for $10!!)
ref: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=260459667170
Message Edited by rkawakami on 08-11-2009 01:13 PM
Ray Kawakami
X22;X24;X31;X41;X41T;X60;X60s;X61s;X300;X301;Z60m;Z61t;Z61p;560Z;600E;600X;T21;T22;T23;T41;R50;A21p;A22p;A31 and A31p
Not a Lenovo employee; just a volunteer helping out here
All personal links to PC-Doctor software removed 8/2012 by mfg request

Configure / Enable network card, and DHCP on VMware Workstation 6

Hi Everyone,
I am newbie in Solaris. If you can walk me through steps by steps, I would really appreciate it.
Problem/Question: One main issue, No network connection.
Background:
VM machine 01:
I installed Solaris 10/06 first, it starts and works ok. However, when I tried to use the Update manager to update, it doesn't allow me to. It said something like "Failed" connection". However, it has normal internet connection, and it is just a litte slow, but internet connection works ok.
VM machine 02:
I installed the most recent distro: Solaris 10 8/07. The installation process went fine. I selected "Network" and connect to "DHCP" at the installation process just like "VM Machine 01". And the installation went through fine too.
The problem comes after the installation and it starts to reboot, and trying to get a IP address.
The boot screen said something like IP 192.168.XXX.XXX has the same Mac Address XX XX XX XX XX XX on pcn01
This error message pops up 4x or so, it then took me back to end section of the installation screen where it asked me if the computer is connected to "Network" and "no Network", and installed the new protocol "IPv6"...
Since I got the error message, I selected "No Network", and it didn't take me to "DHCP" page. Then, the system started fine, but no network connection.
What interesting and wired is that, "Connect Properites" of the PCN01, it shows that it has an IP address, and try to transfer data. Unfortunately, nothing comes up.
On a post from VMware, it mentioned that SUSE Linux sometimes has this problem with the network identifier and mac address is being the same. And it suggested to do some manual changes.
http://kb.vmware.com/selfservice/microsites/search.do?cmd=displayKC&docType=kc&externalId=http--pubsvmwarecom-guestnotes-guestossuse10html&sliceId=&docTypeID=DT_PRODUCTDOCUMENTATION_1_1&dialogID=46496526&stateId=0%200%2046494431
I am not sure if it would be the same for Solaris, and if it may be, would you please tell me where and how to change the mac address in Solaris?
Thanks in advance,
Best,
Xin

do you have dhcpcd installed? nm 0.7 uses dhcpcd instead of dhclient by default, so it seems there is something wrong with that.
oh and !dhcp can be removed from INTERFACES aswell, what does that even do?
as i said above, the things i mentioned before weren't fixes for your problem, so it's no wonder they didn't solve your problem
they were just cleanups for your networking stuff and to make nm really do the part it is supposed to.

How to configure Netgear FA510C Network Card

I installed Solaris 8 (Intel) on my laptop(Compaq Presario
1275) and have NetGear FA510C network card to be
configured. When I installed Solaris, it didn't recognize
the network card, and I have no idea how to configure
this network card. Does any have any idea how to
install and configure this network card?
I'll appreciate your help.
cwpak

Try to use devfsadm -v to find the device
Then use ifconfig dnet0 (not positive this is the right syntax for SMC) to plumb the device.
Then use ifconfig dnet0 192.168.50.4 up
You may have to modify these files to get the IP to come up on startup and properly resolve:
/etc/hostname.dnet0
/etc/netmasks
/etc/resolv.conf
/etc/defaultrouter
/etc/nodename

How to configure SMC 9432TX - Network Card

Hi,
My Solaris8 (Intel) works fine but I just got a NIC card. Can anyone tell me the steps to Install and configure a Network Card.
I have SMC 9432TX .
Thanks

Try to use devfsadm -v to find the device
Then use ifconfig dnet0 (not positive this is the right syntax for SMC) to plumb the device.
Then use ifconfig dnet0 192.168.50.4 up
You may have to modify these files to get the IP to come up on startup and properly resolve:
/etc/hostname.dnet0
/etc/netmasks
/etc/resolv.conf
/etc/defaultrouter
/etc/nodename

Use only one network card with Edge

hi,
is it ok to configure single network card for the edge and do the static routing on that network card. is it supported if yes then kindly providee me the Technet article. If it is not supported then kindly provide me technet article which says that one network
card for lync edge is not supported.
Thanx
SKHATRI

Hello all,
Thanks a lot for your post. May i know the following clarification as i want to use single interface at EDGE server.
Unsupported Scenario
A Consolidated Edge cannot be deployed with a single Network Interface in the environment as the roles has a requirement to have and bind separate IP addresses for internal and external services. At the same time, a single multihomed
network adapter connected to a same IP sub-network for both internal and external routes is not supported for the A/V Edge role specifically.
– Did not understand why not supported, in TCP/IP communication, what will be the issue? If I make sure that external and internal users see the EDGE server with different IP. External
users will see the EDGE server with public IP. The external users will not able to connect internal interface in any case. Internal users/server will see the EDGE server with private IP. They will be able to connect with public IP /service (port).
Besides that, if i use 2 NIC but IP will be from same subnet of DMZ what will be the issue.
Appritiate your response.
Thanks
Ashif

?? configure network-cards under Sol. 8 ?? please heeellpplp

Hi,
I'm a stand alone Solaris's user (at home). Since about 2 months I've installed Solaris 8 on my PC, and wont be able to configure my Internet-Connection and my privat Home-Network.
I'd already read about 500 different publication's pages, but wont be able to go any further. My main PC contain Solaris 8 and has two RTL-Network-Cards. One for the Internet Connection(LAN), and the other (interne hub) for my small privat network at home. I've read there should be two files named: /etc/hostname.XXX0, XXX1. But there arent such files to see by me. The only file I have is "/dev/hostname.". I've tried to create them and lunch some commands I've seen in some manual's page.
Result ===> some error messages by the boot sequence.
Please can anyone help? Without having these cards working, I can't have any Internet connection.
The OS (Solaris) is already working on my PC, and I love it. But the only problem is how to set up these damned hardware, Network-Cards, Sound-Card and. I don't really know how to start with.
Please help!! Dont want to give up and I will not! Please help me to enjoy that hard work.
Thanks for helping.
PS: I'm connected to the internet trought Network (LAN), i.e I'm using a RTL 8029 PCI Ethernet network-card, and the interne Hub is also a RTL 8029 PCI Ethernet card.

yes. you got it .... eg..
/etc/hostname.le0
/etc/hostname.le1
in here put the hostname ... so at the shell prompt:
# hostname <cr>
should give your hostname.
now, in the hosts file: eg:
# Internet host table
127.0.0.1 localhost
<your ip address> <your hostname> loghost
129.156.89.252 host2
you need to reboot after this.
if you get a 'bad address' error on boot,
you probably have a mismatch of hostnames/ip addresses somewhere in their respective files.
also, see:
# man hosts
# man ifconfig

Configure network card on laptop

I've installed solaris 9 on a NEC versa lx laptop and during installation in does not see the 10/100Mbps 16-bit PCMCIA Ethernet PC Card network card. Can someone help me with this problem?
Newcomer

You need to check the x86 hardware compatibility list to see if that laptop and the interface in it are supported.

Can i change the wifi card MAC address in windows 10 /configure/Advanced „Network Address" funktion works?

Many users complained some wifi cards missing the
/configure/Advanced „Network Address” funktion.Without this function
does not work normal MAC adresses which begin for example
„00”.There are many
forums people write about (indignantly)
the problem.
picture here
of what
I mean:
stewx.cba.pl/extend-your-free-wifi-by-spoofing-your-mac-address/
older post more links:
social.technet.microsoft.com/Forums/windows/en-US/8f33667e-ba25-442c-a49b-a3aec79b6cc9/windows-781-can-not-change-the-mac-address-on-wifi-and-cannot-load-login-page-in-public-hotspot?forum=w8itpronetworking
I'm curious about the Windows 10 users
experience with different
wifi cards.
This function working perfectly, all linux platform,Mac,already in android,the old windows XP,windows 2000,
it's a basicthing.This problem affects some reason only are newer Windows platforms and directly the wifi option.

well....it doesn't matter whether the MAC add is 00-14-BF-93-D2-66 or 00:14:BF:932:65 or any other format .. the most important thing is the hex decimal numbers are the same ... so not worry about it...

Configuring PCMCIA Network Card 3Com 3CCFE574BT,3CCE589EC

Similar Messages

Maybe you are looking for