Configuring SNMpv3 in switch 2960 and connect to cisco prime 6.3

hi
I configuring the parameters in the switch for snmp v3 and the cisco prime, but i don´t have any response
but, I configure snmp version1 this work
in the scree on the cisco prime, don´t appear this field´s to configure all parameters for snmpv3
any idea??
thanks

Hi ,
share your SNMPv3 config or I have attached the sample SNMPv3 config , kindly check or reconfigure it and see if it help
Thanks-
Afroz
***Ratings Encourages Contributors ***

Similar Messages

Is it possible to manage the switch SMB 300 series using Cisco Prime Infrastructure?

Is it possible to manage the switch SMB 300 series using Cisco Prime Infrastructure 1.2?

SF300 series is targeted for support in PI 2.0.

Adding new switch in my network including Cisco Prime Infrastructure

hi all,
if I connect new switch to my network, can I let Cisco PI to apply a specific template of configuration to this switch automatically?
how can I do that ?
thanks in advance

Hi,
i followed these steps :
SWITCH SIDE
- configured Prime Infrastructure as snmp-server host;
- enabled snmp-traps for linkup and linkdown events globally;
- disabled snmp-traps for linkup and linkdown on non relevant interfaces using the no snmp trap link-status command
PRIME INFRASTRUCTURE SIDE
- under "Deploy/Monitor Deployment" i deployed template "Interface Health" for all the interested switches
- under "Administration/System Settings/Mail Server Configuration" configured my internal SMTP server to make Prime Infrastructure able to send e-mails
- under "Operate/Alarms & Events" click on "Email Notifications" , then on "Switches and Hubs"
- check the "critical" box , insert the destination e-mail address into the "To" field then click "Save"
- check the "switches and Hubs" box and then click Save
As i know is possible to avoid to configure every single not-interesting port on the switches with "no snmp trap link-status" command (it's a bit annoying when you have tens of switches), using Port Grouping configuration on PI but i tried it without success.
Hope this helps.
Best Regards,

User Name and Password for Cisco Prime Infrastructure 2.1

Hi all:
I am stuck at the login page of Cisco Prime Infrastructure 2.1.
I have tried using the user name root and its password (when log in with root at Vsphere Client) and also the login user name "before" get into the appliance infrastructure, all cannot work.
Anybody knows what is the default username or password or any way to set the username and password for this Cisco Prime Infrastructure 2.1 website?
Thanks!
tangsuan

Hi Tangsuan,
Following is the documented procedure for password recovery..
In order to modify the GUI root user password, you will need to login to the NCS CLI
as an admin user, and enter the command
"ncs password root password <new password>" (without the quotes)
This should set the web interface root user password :
http://www.cisco.com/en/US/docs/wireless/ncs/1.1/configuration/guide/manag.html#wp1268889
If you have lost your CLI password , try the default logging that is ,
CLI user is admin and not root, so please try logging in as admin with
the password that was set during setup. If that does not work , you need
the install disk that came with the appliance to recover that password.
Follow these steps:
Recovering a Lost Admin Password
If you lose or forget the admin password for NCS appliance, follow these steps.
Step 1 Reboot the NCS appliance with the ISO DVD inserted. The Cisco Prime Network Control
System Welcome screen appears:
ISOLINUX 3.11 2005-09-02 Copyright (C) 1994-2005 H. Peter Anvin
             Welcome to Cisco Prime Network Control System
To boot from hard disk, press <Enter>.
Available boot options:
   [1] Network Control System Installation (Keyboard/Monitor)
   [2] Network Control System Installation (Serial Console)
   [3] Recover administrator password. (Keyboard/Monitor)
   [4] Recover administrator password. (Serial Console)
<Enter> Boot existing OS from Hard Disk.
Enter boot option and press <return>.
boot:
Step 2 Select the desired recovery option, 3 or 4, depending on how you
are connected to the appliance and then follow the prompts.
Thanks-
Afroz
***Ratings Encourages Contributors ****

WCS and LMS to Cisco Prime Infrastructure 1.3 Upgrade

Hello,
Our customer is currently having WCS for 500 devices and LMS 3.2 for 1500 devices. We are planning to upgrade to Cisco Prime Infrastructure 1.3.
I want to check is the upgrade procedure that we have planned is ok or we have missed something.
Phase 1: WCS to CPI 1.3 upgrade
1. Check that WCS is at 7.0.230.0 version
2. Export WCS database
3. Install NCS 1.1.1.24 software
4. Contact cisco to obtain trial license for NCS software (L-WCS-NCS1-M-K9 license).
5. Migrate WCS license and import it in NCS software
6. Migrate WCS data to NCS software using ncs migrate command
7. Patch NCS software
8. Inline upgrade to CPI 1.3 software
9. Install proper licenses on CPI 1.3 (WCS and LMS device count)
My concern in this first phase is should I use NCS large image since our Cisco Prime Infrastructure 1.3 software should manage 2000 devices at the end.
Or is it better not to perform inline upgrade and insted go with exporting data from NCS and then importing them to CPI 1.3 that is going to be installed separately?
Phase 2: LMS 3.2 to CPI upgrade
1. Export LMS 3.2 database
2. Install LMS 4.2 software
3. Install license to LMS 4.2
4. Restore data from LMS 3.2 to LMS 4.2
5. Direct upgrade from LMS 4.2 to 4.2.2
6. Export the device list with credentials from LMS 4.2.2 and import it as a Bulk Import in CPI 1.3
At the end we will have CPI 1.3 and LMS 4.2.2 software running.
Is it possible to directly upgrade from LMS 4.2 to LMS 4.2.4 and then import data to CPI 1.3 or we need to go with 4.2.2 version?
Regards,
Jelena

Hello Marvin,
We have restored LMS 3.2 SP 1 database on LMs 4.2 and we have got some error messages during restore. Please see our restore output:
[kalms4/root-ade ~]# /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/res
resolver.pl           restoreDBTableMig.pl restoreJRMMig.pl      restorebackup.pl
[kalms4/root-ade ~]# /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/restorebackup.pl -d /opt/BKP/
Restore started at : 2013/12/05 14:11:58
Please see '/var/adm/CSCOpx/log/restorebackup.log' for status.
     USER ID is ..................................... : sysadmin
     OS of the backup archive is..................... : Windows
INFO:The backup archive is from a different OS. Your current Platform is: Soft Appliance .
You are attempting to perform a Cross Platform Restore..
Do you wish to continue (Y/N) [Y] :Y
     Generation to be restored is ................... : 0
     Backup taken from............................... : /opt/BKP/
     Common Services version in the backup data is... : 3.3.1
     Common Services is installed in................. : /opt/CSCOpx
     The temp folder for this restore program........ : /opt/CSCOpx/tempBackupData
     Applications installed on this machine ......... : [Common Services][Campus Manager][Resource Manager Essentials][Device Fault Manager][cwportal][ipm][upm][cvw][cwlms]
     Applications in the backup archive ............. : [Common Services][Campus Manager][Resource Manager Essentials][Device Fault Manager][opsxml][cwportal][ipm][upm][cvw]
     WARNING: The list of applications installed on this CiscoWorks server does not match the list of
              applications in the backup archive. If you restore data from this backup archive,it may
              cause problems in the CiscoWorks applications.
              Do you want to continue the restore operation? (y-continue or n-quit, y/n)?Y
     Applications to be restored are................. : [Common Services] [Campus Manager] [Resource Manager Essentials] [Device Fault Manager] [cwportal] [ipm] [upm] [cvw]
     Available disk space in NMSROOT................. : 86451488 Kb
     Required disk space in NMSROOT.................. : 35906524 Kb
     (The temp and NMSROOT are on same device, therefore this required disk space includes temp space)
Copying the backup files to the temporary location [/opt/CSCOpx/tempBackupData]
preRestore of [Common Services] has started.
preRestore of [Common Services] has completed.
preRestore of [Campus Manager] has started.
preRestore of [Campus Manager] has completed.
preRestore of [Resource Manager Essentials] has started.
preRestore of [Resource Manager Essentials] has completed.
preRestore of [Device Fault Manager] has started.
preRestore of [Device Fault Manager] has completed.
preRestore of [cwportal] has started.
preRestore of [cwportal] has completed.
preRestore of [ipm] has started.
preRestore of [ipm] has completed.
preRestore of [upm] has started.
preRestore of [upm] has completed.
preRestore of [cvw] has started.
preRestore of [cvw] has completed.
doRestore of [Common Services] has started.
          Cross Platform Update started.
          Cross Platform Update completed.
          License check started.
             WARNING: The license details in the server are different from the backup data.
                      After restoring, please check the license available in the server.
             WARNING: Your current license count is lower than your earlier license count.
                      If you restore the data now, devices that exceed the current licence count
                      will be moved to Suspended state.
          License check completed.
          Restoring certificate.
             WARNING: Cannot evaluate the hostname, hence the certificate
                      may be from this host or another host.
                      [ Certificate not overwritten ]
          Restored Certificate.
          Restoring Common Services database.
          Restored Common Services database.
          Restoring CMIC data.
          Restored CMIC data.
          Restoring CMC data.
          Restored CMC data.
          Restoring Security Settings.
          Restored Security Settings.
          Restoring DCR data.
          Restored DCR data.
          Restoring Certificate key store.
          Restored Certificate key store.
Restoring DCNM CrossLaunch data.
          Restored DCNM CrossLaunch function.
          Restoring JAAS configuration.
          Restored JAAS configuration.
          JRM Job Migration started.
          JRM job Migration done.
doRestore of [Common Services] has completed.
doRestore of [Campus Manager] has started.
          Cross Platform Migration for Campus started.
Cross Platform update Starts for Campus
doRestore of [Campus Manager] has completed.
doRestore of [Resource Manager Essentials] has started.
10% of RME Restore completed
30% of RME Restore completed
50% of RME Restore completed
70% of RME Restore completed
100% of RME Restore completed
doRestore of [Resource Manager Essentials] has completed.
doRestore of [Device Fault Manager] has started.
10% of DFM Restore completed
30% of DFM Restore completed
50% of DFM Restore completed
80% of DFM Restore completed
Going to modify Eight PM report
Modified Sucessfully Eight PM report
100% of DFM Restore completed
doRestore of [Device Fault Manager] has completed.
doRestore of [cwportal] has started.
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.properties ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.script ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.log ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties//defaultUserCommunity.properties ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties//defaultCommunity.properties ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
doRestore of [cwportal] has completed.
doRestore of [ipm] has started.
        10% of IPM Restore Completed
        30% of IPM Restore Completed
        50% of IPM Restore Completed
        60% of IPM Restore Completed
        70% of IPM Restore Completed
        100% of IPM Restore Completed
doRestore of [ipm] has completed.
doRestore of [upm] has started.
HUM database restore starts
INFO:STOP= /opt/CSCOpx/objects/db/bin64/dbstop -q -y -c dsn=upm
SQL Anywhere Command File Hiding Utility Version 10.0.1.4239
INFO: Database Shutdown is in Progress..Please wait
INFO: Stop Engine Args= /opt/CSCOpx/objects/db/bin64/dbstop -q -y -c dsn=upm
INFO: After Database Shutdown RC= 2304
root=C:\PROGRA~2\CSCOpx\databases\upm\upm.db
DBUTILS: Inside Cross Platform
INFO: Current Database password does not match the password of Database being restored
INFO: Using the Password of the Database being restored
HUM database restore successfully completed.
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Threshold
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Threshold/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Custom
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Custom/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller_Failure
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller_Failure/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/TrendWatch
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/TrendWatch/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Availability
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Availability/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPORTUtilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPORTUtilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Utilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Utilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Memory_Utilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Memory_Utilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Availability
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Availability/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Threshold_Violations
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Threshold_Violations/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/CPU_Utilization
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/CPU_Utilization/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPSEConsumption
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPSEConsumption/README.txt
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_ErrorRate
File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_ErrorRate/README.txt
Directory is reportsStarted changing property .
linux
Restored HUM configuration file successfully.
doRestore of [upm] has completed.
doRestore of [cvw] has started.
doRestore of [cvw] has completed.
postRestore of [Common Services] has started.
postRestore of [Common Services] has completed.
postRestore of [Campus Manager] has started.
postRestore of [Campus Manager] has completed.
postRestore of [Resource Manager Essentials] has started.
postRestore of [Resource Manager Essentials] has completed.
postRestore of [Device Fault Manager] has started.
postRestore of [Device Fault Manager] has completed.
postRestore of [cwportal] has started.
postRestore of [cwportal] has completed.
postRestore of [ipm] has started.
postRestore of [ipm] has completed.
postRestore of [upm] has started.
postRestore of [upm] has completed.
postRestore of [cvw] has started.
postRestore of [cvw] has completed.
Restored successfully.
Are this errors going to affect our LMS 4.2 operations?
Then we have upgraded to LMS 4.2.2 and exported data and credentiales for PI import.
On PI 1.3 we have installed WCS 500 devices upgrade license and LMS 1500 upgrade license and now we are having 2000 devices lifecycle license. We have successfully restored WCS data in PI and we have imported LMS devices as bulk import. What is strange is that we have this message in prime regarding licensing:
On LMS 3.2 our customer had saved unlimited number of configuration versioning. After upgrading to LMS 4.2 we can only see last 3 configurations regardless of unlimided number of configurations in previous LMS, so my question is where can we find older configurations in LMS 4.2?
We are planning to turn unlimited versioning on CPI 1.3 now, so our customer will again have feature that they need. Do you have some experiance regarding disk space when all device configurations are stored forever?
Thank you for your help.
Regards,
Jelena

Offline sync using Cellular when switched off and connected to Wifi

Problem with Spotify or Apple iPhone6?? I have the sync over cellular switched off in Spotify, but just synced whilst connected to wifi supposedly based on the WiFi icon showing but it used about 1gb of my cellular data. Latest iPhone6 update applied but might not be the reason. Anyone else experiencing this??? I have had to buy more data so I don't get charged.

I have had the exact same problem. With syncing 2 albums over 200Mb (of 500mb) of my cellular data gone!
Wifi was on (and working with websites etc.), mobile data for Spotify in iOS settings was enabled, syncing in Spotify via 2g/3g disabled and offline mode in Spotify was turned off.
This was on iPhone 5c with iOS 8.1, Spotify version 1.9.0.2744
Please help!

Non-existing connections in Cisco Prime LMS 4.2.4

Hi
We have experienced weird connections in LMS 4.2.4 and earlier versions, even back to LMS 3.2.1. Even if I delete the connections, they reappear as if the connection was present.
Sometimes it is related to a change of interface from 1G to 10G and in some cases other device ...but not always.
It hurts my eyes, watching this, so I hope some of you might know the reason or even better, the solution.
Thanks in advance ;-)

Hi Afroj
Thanks for your reply
I've just tried your suggestion. This is the result.
Acquisition start time 27 Feb 2014, 10:00 CET
Last Acquisition end time 27 Feb 2014, 09:20 CET
(output is old, I know)
From that I conclude, that i does acquire data. The weird part is that it sometimes "forget" that a connection is moved or removed and therefore it sometimes seems that 3 devices are connected on the same media/cable.
I've tried to run a datacollection, but with no result. I does collect data as expected on new devices. If I physically move a device, LMS sometimes moves the connection as well. Other times, it just add the connection, so three devices share the same media, ...even if I delete all the devices and asks it to collect again.
Weeeeird.

Patch and upgrade problems cisco Prime

Hi all
Because of my simple mind I am strugling to upgrade my CPI from 1.2.0.103 to 1.3.
The guidelines are not that good and so i searched through the community and internet.
I did configure the repository. And next i tried to copy the file using tftp, ftp and also from local cdrom.
Not one of my tries did work.
I need your help on the config steps as i believe i do something wrong or miss a command/setting
CPI/admin(config)# repository defaultRepo
CPI/admin(config-Repository)# url tftp://170.237.255.234
CPI/admin(config-Repository)# end
CPI/admin# copy tftp://170.237.255.234/pi_1.2.1.12_update.tar.gz disk:/defaultRepo
CPI/admin(config)# repository defaultRepo
CPI/admin(config-Repository)# url cdrom:/
CPI/admin(config-Repository)# end
CPI/admin# copy cdrom://pi_1.2.1.12_update.tar.gz disk:/defaultRepo
Thanks for your help
Sent from Cisco Technical Support iPad App

defaultRepo shouldn't have a URL that should be assigned to disk:/
Please look at this support doc and it should help you out.
https://supportforums.cisco.com/docs/DOC-26972
Sent from Cisco Technical Support iPhone App

Differences between clients and devices in Cisco Prime infrastructure

Hello
It seems to be a very simple question :
I read the Prime Licensing Guide in order to size the
right version of OVA to deploy in my datacenter .
I don't understand what is a "client" , because there is a topic about it in the data sheet :(cf joined pic)
could you please help me ?
Cheers ;

Hi,
By client , it mean wired client like your laptop or wireless client like your smart phone
License is depended on the devices count not on client count.
Thanks-
Afroz
****Ratings Encourages Contributors ****

LMS 4.2 User Tracking for Avaya IP Handsets and Connected Devices

I manage an environment that makes extensive use of Avaya IP phones and it's frustrating that this seems to limit the usefulness of the User Tracking application within LMS.
We configure the switch (2960) ports connected to the handsets as dot1q trunks with the associated PC being connected to the switch built into the phone.
Having done some forum research it seems that UT only adds an entry for a device connected on a trunk port if it is a Cisco IP phone, not anything else. This is frustrating as it eliminates a large part of our network from being recorded in UT and is doubley frustrating since the PC connected to the switch on the phone also isn't recorded.
Is there any way to get around this problem that anybody is aware of? Thanks

As long as you have a supported Cisco Layer 3 device in your LMS-management domain, you should be able to correlate the IP-MAC addresses in User Tracking (UT).
UT support is not specifically listed for the ASA firewall - I'm not sure it will support that feature if it is the users' gateway.
Useful links:
UT explanation from the LMS Admin Guide
Supported devices listing
Hope this helps.

Ask The Expert: Understanding, Implementing, and Troubleshooting Cisco Prime Network

Ask questions and learn about Cisco Prime Network with Cisco experts Vignesh Rajendran Praveen and Jaminder Singh Bali.
Cisco Prime Network is and Cisco Prime Network provides cost-effective device operation, administration and network fault management for today’s complex and evolved programmable networks (EPNs). It is a single solution to support both the traditional physical network components, as well as compute infrastructure, and the virtual elements found in data centers. Automated configuration and change management combined with advanced troubleshooting and diagnostics greatly help service providers enable proactive service assurance. Additionally, the flexible and extensible architecture is designed to support the multivendor environment, helping to lower operational costs.
This event runs January 5 through January 16, 2015.
Vignesh Rajendran Praveen is a High Touch Engineer with the Focused Technical Services team supporting Cisco's major Service Provider customers in Routing, Switching, Multiprotocol Label Switching (MPLS) technologies and Cisco Prime Network related issues. Previously at Cisco he has worked as a Network Consulting Engineer for Enterprise Customers and as a Customer Support Engineer for Service Provider customers. He has been in the networking industry for ten years and holds CCIE certification (#34503) in the Routing and Switching as well as Service Provider tracks.
Jaminder Singh Bali is a Customer Support Engineer working in SP-NMS TAC team, supporting Cisco's major service provider customers in Cisco Prime Network, Performance and Prime Central related issues. His areas of expertise include Oracle, Linux and NMS applications. He has been in the industry for past six years.
Remember to use the rating system to let the experts know if you have received an adequate response.
The Experts might not be able to answer each question due to the volume expected during this event. Remember that you can continue the conversation in Network Infrastructure community, sub-community, LAN, Switching and Routing discussion forum shortly after the event. This event lasts through January 16, 2015. Visit this forum often to view responses to your questions and the questions of other community members.

Hello Jerome,
A variety of Cisco devices are supported by the the Cisco Prime Network. I would encourage you to go through the below links on the user guide depending the version of Cisco Prime Network being used.
"Cisco Prime Network Supported Cisco Virtual Network Elements (VNEs)"
"Cisco Prime Network Supported Cisco VNEs - Addendum"
Below is the link for the user guide.
http://www.cisco.com/c/en/us/support/cloud-systems-management/prime-network/products-user-guide-list.html
Hope this would help in providing you more clarity.
***********Plz do rate this post if you found it helpful*************************
Thanks & Regards,
Vignesh R P

When is Cisco Prime Infrastructure 2.0 released, and what does 2.0 offer?

We are running Prime Infrastructure 1.3 primarily for wireless management at this point. We have enough licenses to add all our switches, routers, and firewalls, but we're hesitant to do so until 2.0 comes out. While there are some features for backing up and configuring switches and routers, 1.3 still seems pretty limited in regards to non-wireless features. For example, nearly every report in 1.3 is for wireless controllers or AP's, there are no reports I've found relevent for switches and routers. I've read a lot of blogs, cisco posts, and white papers talking about how Cisco Prime Infrastrucure 2.0 will finally consolidate Prime into a truly all-in-one network management suite that can manage the entire Cisco environment. Does anyone know when it's officially being released? Does anyone have an tech sheets on what's new in 2.0, or what its capabilities are? I want to better understand what 2.0 has to offer, when it's coming out, how to upgrade, so I can start planning for the upgrade and eventually importing all our network devices to Cisco Prime for centralized management. Any useful information or links would be appreciated.
Thanks,
Christian

PI 2.0 is in Beta mode for testing in closed group already. However it may still take some time to get released on CCO for FCS.
I think it is expected to be released between aug-sep. BU has also started working on CPI 2.1, which you can see test uploads on CCO.
For what does it have for customers?
> As Cisco have a vision of one network Management software for both wired and wireless infrastructure, which started getting real partially with Cisco PI.
As WCS got evolved to NCS and eventually to Cisco Prime Infrastructure, but it doesnt yet have full Management capability for wired infra., which is there with LMS.
With CPI 2.x Cisco plans to blend entire LMS and WCS features together.
-Thanks

Ask the Expert: Overview of Cisco Prime Service Catalog and Process Orchestrator Solutions

Welcome to this Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about the Cisco Prime Service Catalog and Process Orchestrator solutions.
Cisco expert Jason Davis will discuss Cisco’s network management products offered under the Cisco Prime framework. If you have questions about Cisco Prime infrastructure or data center automation with our Cisco Prime Service Catalog and Process Orchestrator solutions, join us on the Cisco Support Community.
Jason Davis is a distinguished services engineer in the Intelligent Infrastructure Practice team of Cisco Advanced Services. His role is to provide strategic and tactical consulting for hundreds of Advanced Services customers, lead service innovation, and assess new services and technologies. Jason's primary expertise areas are in network management systems, intelligent automation, virtualization, data center operations, software-defined networking, and network programmability.
Based out of the Research Triangle Park (RTP) campus, Jason is also responsible for administering the Research Triangle Park Network Management Lab, Cisco's largest network management lab.
Since joining Cisco in 1998, Jason has been a frequent speaker at Cisco's Networkers and CiscoLive conferences in the United States and Europe. In the past five years he has also been involved in the conference network setup and monitoring. He is a much sought-after resource by the field sales teams to assist with presales solutions and executive briefings. He has provided strategic and tactical network management consulting for several hundred customers.
Jason is a subject matter expert with the following products and features:
Cisco Prime LAN management solution
Cisco Prime infrastructure
CiscoSecure ACS
Cisco Prime Network Registrar
Cisco Process Orchestrator
Cisco Prime Service Catalog
Cisco IP SLA
Embedded Event Manager
SNMPv3
onePK and OpenFlow
Cisco UCS
Device instrumentation
VMware ESX, ESXi, and vCenter
ITIL
Jason received his bachelor of science degree in electrical engineering from the University of Miami (FL). He has been married for 20 years and has 4 children. His interests include providing audiovisual technical support for churches and conference venues, camping and biking with his family, remote-control helicopter piloting, paintball, and recreational shooting.
Remember to use the rating system to let Jason know if you have received an adequate response.
Because of the volume expected during this event, Jason might not be able to answer every question. Remember that you can continue the conversation in Data Center > Intelligent Automation under the subcommunity Cisco Prime Service Catalog shortly after the event. This event lasts through September 12, 2014. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

Hello Jason,
Thank you very much for welcoming me to your expert discussion :) I feel to be in the right place, at the right time. Thank you also for answering question beyond your scope here, much appreciated. The information received will help me to go further as such I have submitted a 5 start rating for your first reply.
That sounds promising about the LMS part so yes, I stay tuned and wait patiently.
Ok, now let’s revert to the actual topic discussed here. Cisco Prime Service Catalog and Process Orchestrator solutions I have briefly read up on this on CCO (where elseJ) and picked out the following quote
---- Quote from the Cisco Prime Service Catalog Data Sheet
Today’s end users want self-service and easy access to IT tools and services.
Simultaneously, organizations are seeking ways to extend their cloud management
platforms beyond self-service delivery of virtual machines and infrastructure resources
while increasing their use of cloud-based solutions to enhance business agility and effectiveness.
Cisco Prime™ Service Catalog offers tremendous benefits to organizations that want to unify the ways in
which all types of IT services are ordered and fulfilled, not just infrastructure requests
---- un quote ---
I try to understand what (at high level of course) happens in the back ground when an order is raised and which vendor solution your product can interact with.
As mentioned in the quoted text, this service catalogue goes beyond the standard infrastructure.
Let’s say, a user wants to deploy a new email services, or in your example, extends or create a new web-portal (i.e. for HR to view and manage holiday, staff absence and benefits).
Your solution will need to interact somehow with the 3rd party vendor application that is capable building such portal I believe.
Without disclosing to many information, I assume the portal is linked to backend VM,s that spin up requested resources (and more magic of course). Perhaps I am mixing this up with another cisco product where a user can go on the portal and spin up virtual Firewalls, virtual Routers can be provisioned in now time.
Out if interest; Is this product also known as Mozart? (project code within Cisco?)
I hope query is ok.
Best wishes
Markus

Cisco Prime Configuration Archive on Interface Flap

Hey All,
We've been using Cisco Prime 2.1 for a bit now and I have a question about the configuration archive based on change events. Will Cisco Prime go and attempt to perform a config backup based on an interface flap? Looking at the audit logs it appears that it does that (see attachment). Is this a default behavior and does anyone see any benefit to this? It seems like if an interface is flapping it will continuously log into the device to see if the configuration has changed.
Brian

Hi Brian,
I don't think configuration achieve can be triggered due to interface flap ,however if there is any change in the configuration yes PI can do the config Archive
Go to Administration > System Settings > Configuration Archive
Archive Configuration on receiving configuration change events? Check box this option
Thanks-
Afroz
***Ratings Encourages Contributors *****

What is the difference in the features between Cisco prime 1.2 and Cisco prime 1.4 ?

Dears,
Please i need to know what is the difference in the features between Cisco prime infrastructure 1.2 and Cisco prime 1.4.
Already i see the release note for each one but the release indicate only the New feature for every one. so i need to know the difference between them not new features.
Wait your kind feedback plz
Regards,

Hi,
New Features and Enhancements
The following topics describe new features and enhancements in Cisco Prime Infrastructure 1.4.
Management Support for WLC Release 7.5
Support for 802.11ac Module
Support for Cisco AP 700
Policy Classification Engine
FlexConnect Audit Support
Autonomous AP Support
Client Stateful Switchover
Cable Modem Monitoring
Support for Secure File Transfer Protocol
and please go through the link and check the data sheet for further clearance.
http://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/prime-infrastructure/datasheet-c78-729879.html

Configuring SNMpv3 in switch 2960 and connect to cisco prime 6.3

Similar Messages

Maybe you are looking for