Configuring SYNCE/PTP on Cisco 7600 and Cisco MWR for NSN NodeB
Hi to All,
I would to ask for support on how i can establish the PTP between Cisco MWR 2941-DC and a NSN NodeB. The Cisco MWR is connected to a Cisco 7600 with SPA-2X1GE-SYNCE where the SSU/OSN clock is connected on the BITS ports. Hope you can assist me with the configurations.
Thanks,
Eugene
Dear Genedeath,
I have noticed that you posted this message since last year ..... have you ever been able to solve the case??
I had a glance to the diagram and it looks quite similar to my case.
I need to configure a Cisco MWR2941 for the very first time in order to support SyncE for packet Abis between a NSN FlexyBSC and a NSN BTS.
BTS---------------Gig x/y MWR Gig x/x-----------------------FlexyBSC
I guess the source clock would be provided by BSC...
Can you support me according to your experience ??
thanks and regards!
Mauro
Similar Messages
-
Communication problem between Cisco 3560 and Cisco SG300.
Dear Support,
I have a Cisco SG300 and Cisco 3560 switches.
3560 is my Core Switch and SG300 is access switch.
From 3560 VLAN information is not passed to SG300.
3560 Configuration:
interface GigabitEthernet0/23
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,2,10,11
switchport mode trunk
SG300 Configuration:
interface gigabitethernet49
spanning-tree link-type point-to-point
switchport mode general
switchport general allowed vlan add 2,10-11 tagged
macro description switch
Please suggest how this issue is resolve.
Regards,
JItesh Mahajan.Dear Aleksandra,
Below Configuration is right or wrong for 3560 and SG300.
3560 Configuration:
interface GigabitEthernet0/23
switchport trunk encapsulation dot1q
switchport trunk allowed vlan remove VLAN 1
switchport native vlan 1
switchport trunk allowed vlan 1,2,10,11
switchport mode trunk
SG300 Configuration:
interface gigabitethernet49
spanning-tree link-type point-to-point
switchport mode general
switchport general allowed vlan add 2,10-11 tagged
macro description switch
Regards,
JItesh Mahajan. -
Re-Paired Cisco DMM and Cisco Show & Share
Hi ...
guys ... do anyone have experience to re-paired Cisco DMM and Cisco Show & Share ? I do re-paired it, but it doesn't success. First i pair Cisco Show and Share with Cisco DMS it success, but when i pair Cisco DMM with Cisco Show and Share it doesn't success (the proccess took so long about 30 minute i do ctrl C and it says failed to install certificate from Cisco Show and Share).
Anyone have idea ?
BRAvoid Pairing Failures
•Pairing fails when you complete these steps in the wrong order. You must use AAI on your Cisco Cisco Show and Share appliance before you use AAI on your Cisco DMM appliance. Do not reverse this order or try to use AAI simultaneously on both appliances.
•Do not use the POP option on the pairing menu. Doing so may cause Cisco Show and Share to fail. If you accidently choose the POP option, you will need to re-pair the Cisco Show and Share and DMM appliances.
Pair Your Appliances
Procedure
Step 1 From the appliance that runs Cisco Show and Share 5.2:
a. Log in as admin to the Appliance Administration Interface (AAI).
b. Choose APPLIANCE_CONTROL > PAIR APPLIANCE.
c. Choose DMM.
Warning Do not choose any other option than DMM.
d. Enter the fully-qualified domain name (FQDN) for your Cisco DMM appliance.
This is the DNS name. Do not enter an IP address.
e. Press Enter.
Your Cisco Show and Share appliance receives and successfully imports a digital certificate from your Cisco DMM appliance.
Step 2 From the appliance that runs Cisco Digital Media Manager 5.2:
a. Log in as admin to the Appliance Administration Interface (AAI).
b. Choose APPLIANCE_CONTROL > PAIR APPLIANCE.
c. Choose SHOW_AND_SHARE.
Warning Do not choose any other option than SHOW_AND_SHARE.
d. Enter the fully-qualified domain name (FQDN) for your Cisco Show and Share appliance.
This is the DNS name. Do not enter an IP address.
e. Press Enter.
Your Cisco DMM appliance receives and successfully imports a digital certificate from your Cisco Show and Share appliance.
See Cisco Link :
http://www.cisco.com/en/US/docs/video/digital_media_systems/5_x/5_2/dms/aai/administration/guide/pair.html -
Difference between Cisco DCNM and CISCO Fabric Manager
Hello Everyone,
I am new to Cisco SAN and just would like to know the differences between cisco DCNM and Cisco Fabric manager and which one is latest as of now.
regards
VINAYHi Viany,
Fabric Manager was renamed DCNM starting at 5.2.
Fabric Manager only monitors SAN Fabrics, while DCNM 5.2 and above can monitor both SAN Fabrics and Ethernet LANs.
Regards,
David -
Routing issue between Cisco Nexus and Cisco 4510 R+E Chassis
We have configured Cisco Nexus 7K9 as core and Cisco 4510 R+E as access switches for Server connectivity.
We are experiencing problem in terms of ARP learning and Ping issues between Cisco Nexus and end hosts.Hi,
So you have N7k acting as L3 with servers connected to 4510?.
Do you see the MAC associated with failing ARP in 4510?. Is it happening with all or few servers?. Just to verify if it is connectivity issue between N7k and 4510, you can configure an SVI on 4510 and assign address from same raneg (server/core range) and perform a ping.
This will help narrow down if issue is between server to 4510 or 4510 to N7k.
Thanks,
Nagendra -
Problem VOFR cisco 3810 and Cisco 1750
-I have a network with equipment 3810 Cisco and Cisco 1750 in topology in stars.
-The router central is a Cisco 3810 wthin a E1 connected to PBX
- other router in the network, have fxs wthin two port
- the network this working with vofr
- the problem is: from an equipment 1750 I can call to a Cisco 3810 but from an equipment 3810 I can not to a cisco 1750.
- but if I place debug in Cisco 1750 ( debug voice ccaip inout) I watch that the call this arriving
- the configurations de routers is OK
- please it can help me---------------Debug voice ccaip inout-----------------------------------
ARBORAL-R#
ARBORAL-R#
ARBORAL-R#ter moni
ARBORAL-R#
*Mar 4 00:01:59.358: cc_api_call_setup_ind (vdbPtr=0x810920C0, callInfo={called=6250,called_oct3=0x0,calling=,calling_oct3=0x0,subscriber_type_str=Unknown,
fdest=1 peer_tag=0},callID=0x80FF6BB4)
*Mar 4 00:01:59.358: cc_api_call_setup_ind type 0 , prot 11
*Mar 4 00:01:59.362: cc_process_call_setup_ind (event=0x81093FA8) handed call to app "DEFAULT"
*Mar 4 00:01:59.362: sess_appl: ev(23=CC_EV_CALL_SETUP_IND), cid(1), disp(0)
*Mar 4 00:01:59.362: sess_appl: ev(SSA_EV_CALL_SETUP_IND), cid(1), disp(0)
*Mar 4 00:01:59.362: ccCallSetContext (callID=0x1, context=0x81074A5C)
*Mar 4 00:01:59.366: ssaCallSetupInd finalDest cllng(), clled(6250)
*Mar 4 00:01:59.366: ssaSetupPeer cid(1) peer list: tag(6250) called number (6250) tag(1) called number (6250)
*Mar 4 00:01:59.366: ssaSetupPeer rotary_dialpeer_status(1)
*Mar 4 00:01:59.366: ssaSetupPeer cid(1), destPat(6250), matched(4), prefix(), peer(81213410), peer->encapType (1)
*Mar 4 00:01:59.366: ccCallProceeding (callID=0x1, prog_ind=0x0)
*Mar 4 00:01:59.366: ccCallSetupRequest (Inbound call = 0x1, outbound peer =6250, dest=, params=0x81074A70 mode=0, *callID=0x8109F780)
*Mar 4 00:01:59.366: ccCallSetupRequest numbering_type 0x0
*Mar 4 00:01:59.366: dest pattern 6250, called 6250, digit_strip 1
*Mar 4 00:01:59.370: callingNumber=, calledNumber=6250, redirectNumber=
*Mar 4 00:01:59.370: accountNumber=, pinNumber=
*Mar 4 00:01:59.370: finalDestFlag=1, guid=06e4.bc49.8945.19b9.0000.0000.fdc3.ac59
*Mar 4 00:01:59.370: peer_tag=6250
*Mar 4 00:01:59.370: ccIFCallSetupRequestPrivate: (vdbPtr=0x81069AF4, dest=, callParams={called=6250,called_oct3=0x0, calling=,calling_oct3=0x0, subscriber_type_str=Unknown, fdest=1, voice_peer_tag=6250},mode=0x0) vdbPtr type = 6
*Mar 4 00:01:59.370: ccIFCallSetupRequestPrivate: (vdbPtr=0x81069AF4, dest=, callParams={called=6250, called_oct3 0x0,
calling=,calling_oct3 0x0,fdest=1, voice_peer_tag=6250}, mode=0x0)
*Mar 4 00:01:59.370: ccSaveDialpeerTag (callID=0x1, dialpeer_tag=
*Mar 4 00:01:59.370: ccCallSetContext (callID=0x2, context=0x810C043C)
*Mar 4 00:01:59.378: cc_api_call_proceeding(vdbPtr=0x81069AF4, callID=0x2,
prog_ind=0x0)
*Mar 4 00:01:59.378: cc_api_call_alert(vdbPtr=0x81069AF4, callID=0x2, prog_ind=0x8, sig_ind=0x1)
*Mar 4 00:01:59.378: sess_appl: ev(20=CC_EV_CALL_PROCEEDING), cid(2), disp(0)
*Mar 4 00:01:59.378: cid(2)st(SSA_CS_CALL_SETTING)ev(SSA_EV_CALL_PROCEEDING)
oldst(SSA_CS_MAPPING)cfid(-1)csize(0)in(0)fDest(0)
*Mar 4 00:01:59.382: -cid2(1)st2(SSA_CS_CALL_SETTING)oldst2(SSA_CS_MAPPING)
*Mar 4 00:01:59.382: ssaIgnore cid(2), st(SSA_CS_CALL_SETTING),oldst(1), ev(20)
*Mar 4 00:01:59.382: sess_appl: ev(7=CC_EV_CALL_ALERT), cid(2), disp(0)
*Mar 4 00:01:59.382: cid(2)st(SSA_CS_CALL_SETTING)ev(SSA_EV_CALL_ALERT)
oldst(SSA_CS_CALL_SETTING)cfid(-1)csize(0)in(0)fDest(0)
*Mar 4 00:01:59.382: -cid2(1)st2(SSA_CS_CALL_SETTING)oldst2(SSA_CS_MAPPING)
*Mar 4 00:01:59.382: ccCallAlert (callID=0x1, prog_ind=0x8, sig_ind=0x1)
*Mar 4 00:01:59.382: ccConferenceCreate (confID=0x8109F7F8, callID1=0x1, callID2=0x2, tag=0x0)
*Mar 4 00:01:59.382: cc_api_bridge_done (confID=0x1, srcIF=0x810920C0, srcCallID=0x1, dstCallID=0x2, disposition=0, tag=0x0)
*Mar 4 00:01:59.386: cc_api_bridge_done (confID=0x1, srcIF=0x81069AF4, srcCallID=0x2, dstCallID=0x1, disposition=0, tag=0x0)
*Mar 4 00:01:59.386: cc_api_caps_ind (dstVdbPtr=0x810920C0, dstCallId=0x1, srcCallId=0x2,
caps={codec=0xEBFB, fax_rate=0x7F, vad=0x3, modem=0x2
codec_bytes=0, signal_type=3})
*Mar 4 00:01:59.386: cc_api_caps_ind (Playout: mode 0, initial 56068,min 33034, max 5688)
*Mar 4 00:01:59.386: cc_api_caps_ind (dstVdbPtr=0x81069AF4, dstCallId=0x2, srcCallId=0x1,
caps={codec=0x8, fax_rate=0x2, vad=0x2, modem=0x1
codec_bytes=30, signal_type=2})
*Mar 4 00:01:59.386: cc_api_caps_ind (Playout: mode 0, initial 0,min 0, max 0)
*Mar 4 00:01:59.386: cc_api_caps_ack (dstVdbPtr=0x81069AF4, dstCallId=0x2, srcCallId=0x1,
caps={codec=0x8, fax_rate=0x2, vad=0x2, modem=0x1
codec_bytes=30, signal_type=2})
*Mar 4 00:01:59.386: cc_api_caps_ack (dstVdbPtr=0x810920C0, dstCallId=0x1, srcCallId=0x2,
caps={codec=0x8, fax_rate=0x2, vad=0x2, modem=0x1
codec_bytes=30, signal_type=2})
*Mar 4 00:01:59.390: cc_api_call_disconnected(vdbPtr=0x81069AF4, callID=0x2, cause=0xAC)
*Mar 4 00:01:59.390: sess_appl: ev(28=CC_EV_CONF_CREATE_DONE), cid(1), disp(0)
*Mar 4 00:01:59.390: cid(1)st(SSA_CS_CONFERENCING_ALERT)ev(SSA_EV_CONF_CREATE_DONE)
oldst(SSA_CS_MAPPING)cfid(1)csize(0)in(1)fDest(1)
*Mar 4 00:01:59.390: -cid2(2)st2(SSA_CS_CONFERENCING_ALERT)oldst2(SSA_CS_CALL_SETTING)
*Mar 4 00:01:59.390: sess_appl: ev(12=CC_EV_CALL_DISCONNECTED), cid(2), disp(0)
*Mar 4 00:01:59.394: cid(2)st(SSA_CS_CONFERENCED_ALERT)ev(SSA_EV_CALL_DISCONNECTED)
oldst(SSA_CS_CALL_SETTING)cfid(1)csize(0)in(0)fDest(0)
*Mar 4 00:01:59.394: -cid2(1)st2(SSA_CS_CONFERENCED_ALERT)oldst2(SSA_CS_CONFERENCING_ALERT)
*Mar 4 00:01:59.394: ssaDisconnectedAlert: redirect_numbers(0)
*Mar 4 00:01:59.394: ccConferenceDestroy (confID=0x1, tag=0x0)
*Mar 4 00:01:59.394: cc_api_bridge_drop_done (confID=0x1, srcIF=0x810920C0, srcCallID=0x1, dstCallID=0x2, disposition=0 tag=0x0)
*Mar 4 00:01:59.394: cc_api_bridge_drop_done (confID=0x1, srcIF=0x81069AF4, srcCallID=0x2, dstCallID=0x1, disposition=0 tag=0x0)
*Mar 4 00:01:59.394: sess_appl: ev(29=CC_EV_CONF_DESTROY_DONE), cid(1), disp(0)
*Mar 4 00:01:59.394: cid(1)st(SSA_CS_ALERT_DISC_CONF_DESTROYING)ev(SSA_EV_CONF_DESTROY_DONE)
oldst(SSA_CS_CONFERENCING_ALERT)cfid(1)csize(0)in(1)fDest(1)
*Mar 4 00:01:59.398: -cid2(2)st2(SSA_CS_ALERT_DISC_CONF_DESTROYING)oldst2(SSA_CS_CONFERENCED_ALERT)
*Mar 4 00:01:59.398: ssa: Disconnected cid(2) state(11) cause(0xAC)
*Mar 4 00:01:59.398: ssaCallDisconnectAlert: cid(2), peer-cid(1)
*Mar 4 00:01:59.398: ccCallDisconnect (callID=0x2, cause=0xAC tag=0x0)
*Mar 4 00:01:59.402: cc_api_call_disconnect_done(vdbPtr=0x81069AF4, callID=0x2, disp=0, tag=0x0)
*Mar 4 00:01:59.402: sess_appl: ev(13=CC_EV_CALL_DISCONNECT_DONE), cid(2), disp(0)
*Mar 4 00:01:59.402: cid(2)st(SSA_CS_ALERT_DISC_DISCONNECTING)ev(SSA_EV_CALL_DISCONNECT_DONE)
oldst(SSA_CS_CONFERENCED_ALERT)cfid(-1)csize(0)in(0)fDest(0)
*Mar 4 00:01:59.402: -cid2(1)st2(SSA_CS_ALERT_DISC_DISCONNECTING)oldst2(SSA_CS_ALERT_DISC_CONF_DESTROYING)
*Mar 4 00:01:59.406: ssaDisconnectDone: Rotary Retry cid(1) peer list: tag(1) called number (6250)
*Mar 4 00:01:59.406: ssaSetupPeer cid(1) peer list: tag(1) called number (6250)
*Mar 4 00:01:59.406: ssaSetupPeer rotary_dialpeer_status(2)
*Mar 4 00:01:59.406: ssaSetupPeer cid(1), destPat(6250), matched(0), prefix(), peer(81211DC4), peer->encapType (5)
*Mar 4 00:01:59.406: ccCallProceeding (callID=0x1, prog_ind=0x0)
*Mar 4 00:01:59.406: ccCallSetupRequest (Inbound call = 0x1, outbound peer =1, dest=, params=0x81074A70 mode=0, *callID=0x8109F7C0)
*Mar 4 00:01:59.406: ccCallSetupRequest numbering_type 0x0
*Mar 4 00:01:59.406: dest pattern ...., called 6250, digit_strip 0
*Mar 4 00:01:59.406: callingNumber=, calledNumber=6250, redirectNumber=
*Mar 4 00:01:59.406: accountNumber=, pinNumber=
*Mar 4 00:01:59.410: finalDestFlag=1, guid=06e4.bc49.8945.19b9.0000.0000.fdc3.ac59
*Mar 4 00:01:59.410: peer_tag=1
*Mar 4 00:01:59.410: ccIFCallSetupRequestPrivate: (vdbPtr=0x810920C0, dest=, callParams={called=6250,called_oct3=0x0, calling=,calling_oct3=0x0, subscriber_type_str=Unknown, fdest=1, voice_peer_tag=1},mode=0x0) vdbPtr type = 11
*Mar 4 00:01:59.410: ccSaveDialpeerTag (callID=0x1, dialpeer_tag=
*Mar 4 00:01:59.410: ccCallSetContext (callID=0x3, context=0x810C0D90)
*Mar 4 00:01:59.458: cc_api_call_proceeding(vdbPtr=0x810920C0, callID=0x3,
prog_ind=0x8)
*Mar 4 00:01:59.462: sess_appl: ev(20=CC_EV_CALL_PROCEEDING), cid(3), disp(0)
*Mar 4 00:01:59.462: cid(3)st(SSA_CS_CALL_SETTING)ev(SSA_EV_CALL_PROCEEDING)
oldst(SSA_CS_MAPPING)cfid(-1)csize(0)in(0)fDest(0)
*Mar 4 00:01:59.462: -cid2(1)st2(SSA_CS_CALL_SETTING)oldst2(SSA_CS_ALERT_DISC_CONF_DESTROYING)
*Mar 4 00:01:59.462: ssaIgnore cid(3), st(SSA_CS_CALL_SETTING),oldst(1), ev(20)
*Mar 4 00:01:59.466: cc_api_call_disconnected(vdbPtr=0x810920C0, callID=0x3, cause=0x3)
*Mar 4 00:01:59.466: sess_appl: ev(12=CC_EV_CALL_DISCONNECTED), cid(3), disp(0)
*Mar 4 00:01:59.466: cid(3)st(SSA_CS_CALL_SETTING)ev(SSA_EV_CALL_DISCONNECTED)
oldst(SSA_CS_CALL_SETTING)cfid(-1)csize(0)in(0)fDest(0)
*Mar 4 00:01:59.466: -cid2(1)st2(SSA_CS_CALL_SETTING)oldst2(SSA_CS_ALERT_DISC_CONF_DESTROYING)
*Mar 4 00:01:59.466: ssa: Disconnected cid(3) state(1) cause(0x3)
*Mar 4 00:01:59.470: ccCallDisconnect (callID=0x3, cause=0x3 tag=0x0)
*Mar 4 00:01:59.470: ccCallDisconnect (callID=0x1, cause=0x3 tag=0x0)
*Mar 4 00:01:59.470: cc_api_call_disconnect_done(vdbPtr=0x810920C0, callID=0x3, disp=0, tag=0x0)
*Mar 4 00:01:59.470: sess_appl: ev(13=CC_EV_CALL_DISCONNECT_DONE), cid(3), disp(0)
*Mar 4 00:01:59.474: cid(3)st(SSA_CS_DISCONNECTING)ev(SSA_EV_CALL_DISCONNECT_DONE)
oldst(SSA_CS_CALL_SETTING)cfid(-1
ARBORAL-R#
ARBORAL-R#
ARBORAL-R# -
Cisco SAMI (Cisco Service and Application Module for IP) modules
Hi,
Could anyone confirm whether Cisco SAMI module on 7600 supports traditional ppp over vpdn wholesale broadband?
Currently we have setup on Cisco 7200's and we want to upgrade the hardware to 7600 to scale better, MWAM module supports the VPDN configuration but its now end of sale and replacement product is SAMI whose literature is quite confusing.
Thanks
HiteshTry this link for more information on cards
http://www.cisco.com/en/US/products/hw/univgate/ps501/products_white_paper0900aecd801f92c1.shtml -
Connectivity issues between Cisco 2901 and Cisco SG300-52
Hello,
I am having some serious connectivity issues between the hosts in my LAN.
My LAN is based on a Cisco 2901 router and a Cisco SG300-52 port switch.
The issue that has been happening is that connections between hosts on the LAN (remote desktop, extended ping, etc) is very unstable, at some point I can see a 35% lost packets on an extended ping. This happens at any time of the day and from any host.
All hosts are on the same Vlan(default Vlan) and on the same subnet. Some hosts have fixed IP addresses (servers and network equipment) and others obtain their IP address trough a DHCP reservation established on the router (reserved with the MAC address of every host).
I can provide further details if needed, because this issue is very serious and I would really appreciate any insight or support.
Many thanks in advanced.
Sair Amer
EDIT: After doing every test we could think of, we finally found the reason behind this problem.
It turns out that the switch has problems handling communications between clients at different speeds, because most of the hosts connected were working at 100 Mbps but the servers were working at 1000 Mbps (and the communication between host and servers wasn't stable).
After manually setting the speed on all ports to 100 Mbps the problems have stopped.
Many thanks for you help on this issue.Building configuration...
Current configuration : 4123 bytes
! Last configuration change at 12:06:16 PCTime Sat Jul 19 2014 by ccp
version 15.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Foninsa
boot-start-marker
boot-end-marker
no logging buffered
enable secret 5 $1$BDbJ$HN3VP8nmywrGB55RCxPd30
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
clock timezone PCTime -4 0
clock summer-time PCTime date Apr 6 2003 2:00 Oct 12 2003 12:00
no ip cef
ip dhcp excluded-address 192.168.1.1 192.168.1.10
ip dhcp excluded-address 192.168.1.151 192.168.1.255
ip dhcp pool FONINSA
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 8.8.8.8 8.8.4.4
ip dhcp pool Laptop-Sporta-Wifi
host 192.168.1.10 255.255.255.0
ip name-server 8.8.8.8
ip name-server 8.8.4.4
no ipv6 cef
multilink bundle-name authenticated
crypto pki trustpoint TP-self-signed-213585710
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-213585710
revocation-check none
rsakeypair TP-self-signed-213585710
crypto pki certificate chain TP-self-signed-213585710
certificate self-signed 01
30820229 30820192
quit
license udi pid CISCO2901/K9 sn
license boot module c2900 technology-package securityk9
username ccp privilege 15 password
redundancy
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 190.196.21.98 255.255.255.248
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
interface GigabitEthernet0/1
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
no ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip nat inside source list 1 interface GigabitEthernet0/0 overload
ip nat inside source static tcp 192.168.1.3 21 190.196.21.98 21 extendable
ip nat inside source static tcp 192.168.1.3 80 190.196.21.98 80 extendable
ip nat inside source static udp 192.168.1.8 1194 190.196.21.98 1194 extendable
ip nat inside source static tcp 192.168.1.4 3389 190.196.21.98 3389 extendable
ip nat inside source static tcp 192.168.1.9 3389 190.196.21.98 10000 extendable
ip nat inside source static tcp 192.168.1.3 3389 190.196.21.98 20000 extendable
ip route 0.0.0.0 0.0.0.0 190.196.21.97
access-list 1 permit 192.168.1.0 0.0.0.255
control-plane
line con 0
password $
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 5
access-class 23 in
privilege level 15
password #
transport input telnet ssh
no scheduler allocate
end -
Documentation of cisco::eem and cisco::lib libs
Hello Experts,
Would you be able to help me find the link to complete documentation of cisco:eem / cisco::libs libraries ?
Thank you.Some of the available functions are documented on Cisco.com in the EEM Tcl guide (e.g., the CLI functions and the mail functions). Some of the others I mention at https://supportforums.cisco.com/docs/DOC-12757#Tcl_Packages . Between the two sources, I think you'll find everything you're looking for.
-
How Cisco NAC and Cisco NAC Agent works
HI,
Can anyone help in explaining in detail for Cisco NAC will work in L2 OOB mode?
Also, what is the path from the time the end user connects to the network till he gets access to the network?
Please reply soon.Its urgent.I really do not know if you will find the answer that you are looking for. From what I remember NAP was an option that was available with the ACS via a special patch. This is only supported for vista clients if memory serves me correct.
Here is the link that will help you with the basics.
http://www.cisco.com/en/US/netsol/ns466/index.html
We do not get much case volume or exposure to the NAP solution and with ACS 5.2 and ISE around the corner it might be too late to go through this setup and then run into issues with acs 4.2 possibly hitting eol/eos.
Thanks,
Tarik -
Integrating Cisco ACS and Cisco NAC Manager - Downloadable ACL
Hi There
I have Cisco NAC setup in my environment. These are all working fine. The users will get themselves authenticated via Cisco NAC Manager. The Cisco NAC Manager talks to the Cisco ACS for the user database portion. These are all working fine. I would like to enable Downloadable ACL. I have tried using the CISCO-AV-PAIR method and creating a downloadable ACL entry in Shared Components, but nothing works. It's either I'm doing it wrongly or this setup of mine doesn't support downloadable ACL? Please kindly advice.
Regards,
Ram
+6-012-2918870Hi,
That is not possible.
You cannot push ACLs into the NAC manager.
If you are doing Radius authentication from NAC manager, what you can do is to create Roles on the NAC manager, and on those roles you define traffic policies.
Using Radius attributes you can then map users to Roles.
Please take a look into this:
http://www.cisco.com/en/US/docs/security/nac/appliance/configuration_guide/48/cam/m_auth.html#wp1158789.
HTH,
Tiago
If this helps you and/or answers your question please mark the question as "answered" and/or rate it, so other users can easily find it. -
The question is whether Ciscworks 3.1 or version 4.0 supports Cisco ISE as integration for authentication
Hi,
Nope its not supported.
Thanks,
Gaganjeet -
Routeur cisco 1841 and cisco SA540
I already have 1841 router and I am trying to install SA540 as firewall. Can someone help me how to configure these
two? I tried once but failed. I can connect Internet from firewall but I can not connect Internet from PC which connected to router.
If I have to tell you more information, please let me know.
Thank you.Tahar,
How far you can get? Do you have connectivty between the SA and the 1841 Router? Is the Router able to go out to the internet? In your computer, can you see an ARP being build for the IP address of the router?
Mike -
my ipod suddenly asked me to connect my ipod to iTunes and it's saying that it's in recovery mode and I need to reset it to factory default but I don't want to lose any of my media and I haven't synced to a computer or backed it up and it wont let me sync it or retrieve any data from it. please tell me how to keep my media from being deleted?
i have, its connected to my sisters computer,it starts to restore then says there was a problem downloading the software for the iphone, the network connection has timed out. what does this mean?
-
Cisco 7600, SCE8000, Etherchannel
I have two Cisco 7600 and 4 Cisco SCE8000.
I try connect two 7600 through etherchannel with sce.
I read MGSCP design guide and configured src-ip load-balance on one 7600 and dst-ip on another 7600.
I tested by test etherchannel load-balance command, IPs are use same interfaces on etherchannels.
But I see all numbers of sessions on each SCE but not 1/4 of all sessions.
What may be wrong in configuration?After I wrote to config Cisco SM command force_subscriber_on_one_sce=true and restarted SM, I have 100% control CPU utilization on SCE and high CPU utilization of SM server.
Maybe you are looking for
-
Why is the MacBook Pro no longer available in a 17" screen?
Why is the MacBook Pro no longer available in a 17" screen?
-
Help !!! Homogeneous system copy hold on step: Create Database
Group, we use homogeneous system copy to install PRD system. The system hold on step : create databse. When we check the server and found the data library has been restored from tape. The installation just hold on the step and can't going on. And th
-
HP Mini 110 asking for current password, won't boot
Hello I have the same issue with my netbook: Enter CURRENT Password: Fatal Error... System Halted CNU938555L Thanks!
-
Oracle Streams Implementing Step by Step in oracle10g
how to implement Oracle streams in Oracle10g provide a step by step Document regarding Oracle Streams implementation.
-
HI, Users in our Knowledge Center (KC) are getting created automatically. The Start Date is getting populated as 01-01-1900. Is there any way by which we can set this Start Date as System Date? Thanks in advance,