Configuring The DVI Port?

Does the DVI port require some sort of setup and/or configuring when plugging in a monitor.
Our IT department is adding Dell 19" flat panel monitors to our PowerMacs.
They plugged the monitor into the DVI port and nothing happened.
What else could be the problem?
Thanks.
Richard

Hi there,
Welcome to the Discussions!
One of the things we ask new members to do is fill out the computer portion of the My Settings --> over there on the right. Then we can see what kind of Mac you have and give you better advice, thanks.
DVI ports don't need configuring. The key on DVI-I connectors forms a plus sign, while on DVI-D connectors it forms a minus sign. Look here to identify your type of DVI:
http://www.audioholics.com/techtips/specsformats/audiovideoconnections.php
Note: Many Mac G4's came with ADC/VGA video ports, these require a ADC>DVI Adapter.
In addition, it just may be that the video card in your Mac cannot provide the proper resolutions for the Dell monitor. We'll need to know more info about your Mac to determine that.
Regards, Dave

Similar Messages

  • Is it possible for a mini DVI port on the graphics card to stop working while the DVI port works fine?

    I have a 27 inch cinema LED display that will not work when I plug into a Mac Pro (10.6.8) mini dvi port. But it will work fine on another Mac Pro with the same system and other Mac Pros with Lion and Mountain Lion. I can get a 20 inch LCD monitor to work in the DVI port on the mentioned problem Mac.
    I've ran all software updates and troubleshooting utilities.

    Real, Welcome to the discussion area!
    Sorry to douse your enthusiasm but that is NOT a mini-DVI connector. It is a mini-VGA connector.

  • I would like to extend the screen from my circa 2013 27in iMAC with thunderbolt onto my circa late 2006 imac using the DVI port on that iMAC. Is this possible? If not is there another approach I can use?

    I would like to extend the screen from my circa 2013 27in iMAC with thunderbolt onto my circa late 2006 imac using the DVI port on that iMAC. Is this possible? If not is there another approach I can use? My 2006 iMAC is showing it's age but I figure I can use it as just a monitor just fine. Assuming I can connect the two together.

    That older iMac isn't designed to receive video input through the mini-DVI connection. Only certain newer iMacs are able to be used as displays.
    Your only options are to use something like ScreenRecycler mentioned above.
    ~Lyssa

  • Macbook Pro 4,1 (early 2008) is the DVI port analog or digital?

    I have been tasked with a slide show presentation on a family member's HD TV using my MacBook Pro 4,1. The TV is a slightly older big screen TV without HDMI inputs. I would lke to use the component (YPbPr) inputs on the TV rather than VGA. VGA degrades the image appearance too much.
    I purchased a "ViewHD" HDMI input (Digital) to YPbPr (analog component) Output Switch Converter with the thought of using my 2nd Gen Apple TV (ATV) to connect the ATV via HDMI into the Converter and output the component YPbPr to the TV set. I am looking for a simple, elegant solution as I know this question will rear it's ugly head again.
    First, I could find no resources that discusses the output of the DVI port on the MBP. Is it DVI-D, DVI-A, or DVI-I?
    Is there an adaptor out there that I can use to change the DVI out on the MBP (if it is digital) to HDMI so I don't have to use the Apple TV?
    Any help or solutions would be greatly appreciated.
    TIA

    The DVI connector on a MacBook Pro supports both Analog and Digital output.

  • How to configure the eth1 port of NIcRIO 9024 to another IP address and subnet mask

    Hi ,
    I am using cRIO 9024 and am planning to configure it to be an MMS server that interacts with a client which is in another network with different IP and subnetmask. I want to run the server VIs from the host computer via the eth0 port and want to communicate the MMS messages through the eth1 port. the eth0 port is configured as a static IP as shown in the screenshot attached and would like to assign a separate IP and subnet mask to the other port . But when I try to save the configuration I get the error "Could not save your changes tot he target.The subnet mask for eth1 is invalid" .
    I have already directly cross connected the Crio and have disabled the firewalls and still am not able to configure it.
    1) is it possible to configure the ethernet ports to have separate IPs corresponding to different networks and thus the subnet masks?
    2) If its possible then what is the mistake i am doing while configuring it ?
    I would be extremaly grateful to have a reply on this as its pretty desperate to spend a lot of time just to set up the IP configurations..!!!!!
    Regards
    Abhinav

    Dear Abhinav,
    I'm sorry but what you are tryining to do is not suported by the Second Ethrnet Port on any cRIO and so you getting this error meeage.
    Here a abstract out ouf the KnowledgeBase How do I Configure the Dual Ethernet Ports on Real-Time Controllers?:
    Ethernet port 2 is currently not supported to communicate outside its own subnet. There is no capability of configuring the Default Gateway for Ethernet port 2 and therefore cannot connect to a large isolated intranet.  However, there appears to be a common misconception that this port can only be used for communication between NI products: this is not the case, though any communication through the secondary port must be within the same subnet.
    Kind Regards,
    SG3 | Applications Engineering | National Instruments | NIG |

  • ATI X800XT is adc port same dvi signal as the dvi port

    For starters, what does "adc" stand for? Does it mean the adc is an analog port needing conversion to digital for display to an apple cinema display? someone at apple just said it stands for apple display connection. Yes, I know I still need an adapter, but I'm wondering if this port is inferior the the dvi port on the card. I don't know if the adaptor is just changing the physical hardware connections, or something else.
    I want to go from the adc port thru an adc/dvi adaptor to the matrox mxo box, out of the mxo to apple hd 23" display. I need to reserve the other graphics port (dvi) to go thru a dvi/vga adaptor to my vga monitor.
    Is the adc port on the card the same as the dvi port in terms of the type and quality of signal? What is the adc port anyway?

    The video quality should not be compromised by using any of these adapters. The ADC outputs the same exact digital signal as the DVI outputs. The ADC-to-DVI adapter basically discards the USB and power features and passes the digital AND analog signals through.
    As mentioned above, both ADC and DVI also carry analog video signals. Using a DVI-to-VGA adapter, an ADC-to-VGA adapter, or a combination of both will allow you to use an analog VGA monitor from either port on your video card, again with no degradation of the signal.
    If you are missing any or all colors or the signal is degraded in some way, you must have a bad connection, bad adapter, or bad cable. Try reconnecting or replacing each part one at at time to determine the culprit.
    As for the problem of non-matching DVI connectors, check the link below to determine which ones you have and which ones you need. There are pictures of each connector on this page:
    http://en.wikipedia.org/wiki/DigitalVisualInterface
    http://en.wikipedia.org/wiki/AppleDisplayConnector
    You should be able to find an adapter (or gender changer) that matches up to your cable. A web search should give you plenty of sources and options. You may try a place like Cyberguys.com: http://www.cyberguys.com/ (Search for "DVI gender" to see all available adapters.)
    With quality cables and adapters, you should be able to achieve what you are trying to do with no signal degradation to each of your monitors. Let me know how it goes.
    Brent

  • How to connect my MacBookPro to my old TV using the DVI port?

    I would like to use my MacBookPro to play a DVD on my TV, and I don't know how to do it.
    In fact what I want to do is to be able to send the DVD info to an external DVD recorder to copy a DVD from my friend's wedding. I have a Sony DVD recorder connected to my TV set and was planning on using that. Any suggestion would be greatly appreciated.
    thanks,
    Cibele

    Hi Cibelej. Regarding playing DVDs on your TV, I would recommend getting a DVI to Video cable (~$19 from Apple store). Then, you can set your TV as a second display and then configure the Apple DVD player to play the DVD on the second display. Voila! DVD on your TV through your Mac. You will need to get a S-Video or composite video cable to hook from the TV (the yellow socket) to the adapter. Now, for the audio, you need a standard wire that has a 3.5 mm headphone jack at one end to plug into your audio out in the MacBook Pro and stero audio cables on the other end (they're usually white and red) to plug into the audio ins on the TV. I would recommend getting something like this, although it is a bit pricey. Of course, you can buy all the components individually (cheaper probably).
    As for recording onto an external DVD recorder, I'm not too sure about this, but I would imagine you could take the video and audio cables (as described above) and instead of plugging them into the TV, plug them into the DVD recorder and then use the DVD recorder accordingly.
    Hope that helps somewhat! Good luck.
    800 MHz PowerBook G4 (Ti), 2.33 GHz C2D MacBook Pro   Mac OS X (10.4.8)  

  • Is there ANY way to configure the wired ports on Airport Extreme with 7.6.1 software?

    I need to connect a Cisco router to one of the wired ports because I'm creating a home lab with several switches and routers and attached hosts. I need the VERY BASIC ability to set (or even just to SEE) what IP address the AirPort is using/assigning, but with the current AirPort Utility, you apparently can't show the DHCP table for wired connections or set up a static pool of addresses to use or really, to do anything else that is ABSOLUTELY BASIC networking configurations for a router. I don't even know what range of IP addresses the AirPort is using for the wired ports.
    I love this device - it works much better than my old Linksys that I replaced a couple years ago, but this is the Apple Nannies taking things too far. Sure, make the products easy to configure and use, but stop taking away the ability for advanced users to actually use the product because all you're doing is ******* off your power users - which are the exact people whose friends always ask for recommendations on what products to buy. I've always recommended Apple products to everyone, but if they're going to engineer everything so that only stupid people can use them, then only stupid people will buy (and recommend) them. (Can you tell I'm annoyed that I've wasted so much time on a completely unnecessary and irrelvant side-issue when I should be already working on my actual work project?)
    /Rant-off
    So, does anyone know how to access the actual configuration of the AirPort Extreme so I can use a static IP address for my Cisco router that's plugged into one of the AirPort's wired ports? That's all I need.
    Thanks.

    The AirPort assigns IP addresses via DHCP in a range you specify. You may also elect to assign devices their own static IP addresses. That does not involve the Extreme at all, though you may "reserve" those addresses in its DHCP Reservations table.
    AirPort Utility > Network > Network Options...
    Assigning static IP addresses obviates any need to determine the IP addresses the Extreme assigns.
    Update its firmware to version 7.6.3.

  • Third Party LCD Monitors - using the DVI port.

    More often than not, manufacturers of LCD monitors do not address the compatibility of their products with the Macintosh computer. If there is an entry regarding use of their monitor with the Mac, it shows the use of the VGA (analog) port or the need for an adapter. In nearly every case tested, LCD monitors having a DVI-D input port can be operated from the DVI-I port on nearly all Mac graphics cards. Recent testing with a *PM G4 MDD (NVIDA 9000)* and an *LG W2600H* monitor proved that the Mac desktop opened at full monitor resolution. Only drawback with using a non-Apple monitor is that now the CPU requires manual startup from the front panel button; which is often hit-or-miss on the PM G4.

    I have never had that problem before and I just got a viewsonic 20 inch lcd studio type flat panel monitor.

  • Is it possible to configure the switch port to mode trunk if I m going to put a Pc on that port?

    If the answer is yes then what are the adventages and the disadventages of doing this. I've proof this with real switches and configuring the ports as trunk with a pc and the pc can ping other pc that are on the same Vlan or configure as trunk. I would like to know why does that happend?

    Hi,
    It may work, you can configure an interface connecting to host as a trunk link but only if you want that host to receive data from multiple vlans since trunks allowed all vlans per default.
    Usually, on a switch you configure vlans to logically devide the users and to avoid flooding all the users with all the information from multiple vlans which they do not need and which causes unnecessary burden on the ports carrying traffic.
    Hope this helps.

  • How do i configure the usb port on a draytek vigor 2820n router for use with my imac

    i have an imac connected to the internet through a draytek vigor 2820n router. this router has a USB port with a HP Deskjet 5560 printer attached (for use as a network printer for other machines on the network). How do I configure this printer on the iMAC?

    I checked on the HP web site. Your aswer is on the HP website under your printer type. Update your drivers and follow the instructions given by HP and the printer will work as you have it connected.
    Good Luck

  • Question about output through the DVI port

    The problem: I am using a DVI to HDMI cable to send video to an AV receiver. The AV receiver strictly only accepts a DVI-D (Digital) signal. Upon turning it all on, the MacBook Pro screen reloads and appears to be sending video out, based on the AV receiver's model name appearing in the Display's menu bar. The receiver however reads "No Signal". Most likely this is because the MBP's dual-signal port is giving it problems (it can send both analog and digital).
    Is it possible to elect to send a digital-only signal? The cable itself does not include the extra pins for analog, so I'm not sure why it would think it is.
    Keep in mind I'm not entirely sure this is the problem, I just have confidence in this theory.
    Regards,
    Edward

    HDCP: The cause of, and solution to, all of life's problems.

  • 1080p via the DVI port

    Is it possible to connect a 1080p TV to the Mac Pro? This would mean using a DVI to HDMI cable. And assuming the connection works, would that monitor display 1920x1080 pixels? What I'm trying to do is get a large display at a readable pixel density (around 72 dpi). A 32 inch 1080p tv would get me down to 69-70 pixels per inch, which is a lot easier on the eyes than any computer monitor. Has anybody ever tried this? I know Sony's XBR9 claims (in the manual) to be able to deliver 1920x1080 computer signal.

    I have a Sony 52' XBR5 connected to my Mac Pro.
    I used to use a DVI > HDMI cable to connect Mac Pro to my TV, however, the text while readable was no way as clear as using a regular LCD monitor. I was able to get a resolution of 1920 x 1080 with no problems.
    The 52" XBR5 comes with a VGA PC input, after switching to a DVI > VGA cable I am 100 times happier than with the HDMI cable. The resolution is still 1920 x 1080, but the text is much much clearer/sharper. I sit about 10 feet away from the TV and I am able to read the text perfectly.
    I'm using the ATI Radeon HD 4870 with a DVI > VGA (TV), and Mini Display Port > DVI (26" Samsung Syncmaster). I have noticed that when I wake up the displays I only get the colored static on my LCD monitor and not on the TV.

  • T420s Linux and the DVI+VGA port

    Hi,
    I currently have some problems with my graphic ports of my new ThinkPad T420s (4173-W1J). My problem is a bit complicate (I think) but I will do my best to explain it very detailed. Sorry in advance for any stupid mistakes I made with my configuration.
    Problem 1:
    I have ordered the notebook with the Intel graphic card, not the NVIDIA one. What I do not understand - If I look in the BIOS of the notebook, I find something with "OPTIMUS", what indicates to me that there is the NVIDIA card inside. Also, if I call "lspci" using my Linux (Kubuntu 11.04) system, I get the following TWO graphic cards:
    00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)
    01:00.0 VGA compatible controller: nVidia Corporation Device 1056 (rev a1)
    running "lsmod", I get the following output (only relevant video modules, as I identify them to be relevant):
    uvcvideo 72195 0
    videodev 82052 1 uvcvideo
    nvidia 10709116 0
    nvram 14419 1 thinkpad_acpi
    i915 515121 2 video 19438 1 i915
    So I thought - "hey, maybe they made a mistake during configuration and send me the more expensive NVIDIA card included", so I tried to install the nvidia drivers "apt-get install nvidia-current nvidia-settings", but after this my KDE (x-server) does not boot up anymore. After removing the nvidia packages, X-Server booted up again without any problems. How can I find out either of the NVIDIA card is REALLY included, or only the Intel HD? If the NVIDIA is included, what do I have to take care about to enable the correct nvidia drivers?
    Problem 2: The main reason why I came to problem 1 was, that I did not get the DVI port of my attached docking station to work. On the one hand, the VGA port works fine, on the other hand every time I attach the notebook to the docking station, I always have to reconfigure the screen resolution and position manually. Even if I say "save as default", he somehow forgets this configuration every time. Also, sometimes the VGA screen does not work, even if I use the same configuration like ever -- I then have to "exchange" the "left of, right of, clone, ..." a few times and it starts working.
    For sure, no cable, monitor or whatever is broken - since e.g., I am using the internal and external monitor at the same time right now (in 2-monitor-mode).
    So I wanted to solve this issue by using the DVI port - but this port does not work at all (at least I do not know how to enable it!). Using google I found out, that if the NVIDIA card is inside, and the "OPTIMUS"-"feature" is used, than one needs to use the NVIDIA card, otherwise the DVI port does not work. Sadly, as discribed in problem 1, I am neither sure if I have the NVIDIA card inside, nor know how to enable the DVI port at all.
    Any help would be very appreciated. Thank you in advance.

    Hi,
    after I've forced the BIOS to use only the discrete graphic, I now have additional problems.
    First, my system hangs every 2nd time before I even see the grub menu (which runs in graphic mode, thus the screen is blue). If it freezes, I only see a blue screen. If not, I see the blue screen with the normal grub menu. This seems to happen every 2nd boot-up.
    A similar issue I had before, since I use full-disc-encryption and grub was unable to load the fonts from my hard-disc, so I copies all grub fonts to the boot partition (what is of course not encrypted).
    Second problem, I've installed the NVIDIA drivers you suggested, worked without any problem. After restart, KDE showed the nvidia-logo correctly. But after the login, KDE initialises the user-settings, and there he again freezes my system completely (at about 2/3 of the user-settings-initialisation).
    To be honest, I do not know how to proceed. :-(

  • Possible to use the MBP display for use with XBOX 360 through DVI port?

    Hi everyone, I know that the topic sounds ludicrous to probably a lot of you. After all, how dare a Mac user use a Microsoft machine right ;)? Well, truth be told, I like the 360 and that's the only MS product I prefer to use.
    Anyway, I'm going to be picking up my own 360 within the next few days and am currently deciding whether to also buy a new HDTV with the purchase or if I can wait. I'm going to be buying a new TV eventually but I was hoping to put off the purchase for a while since I remembered that the 360 can hook up to monitors through VGA. So what I want to know is whether the DVI port on my MBP is output only or will it accept input signals? Also, if it is possible to hook up my 360 through the DVI port, is there an easy way to attach the DVI-VGA adapter to the 360 seeing? By this I mean, the adapter is only about three inches or so and it would be pretty difficult to attach both machines to each other, so I was wondering if there might be a female-female VGA adapter bridge or some easy method of doing this.
    Thank you all for your help in advance.

    Outsider,
    Check out this link and enjoy the 360 on your MBP!
    http://faq.elgato.com/index.php/faq/more/288
    Here is another one!
    http://faq.elgato.com/index.php/faq/more/443
    N8

Maybe you are looking for