Configuring the Network interface settings in E250

Hi All ,
I have installed a Solaris 9 in E250. We are not able to bring that in network.
We are able to ping the local ip address and not able to reach the gateway address.
I checked the NIC settings, the link_mode is half duplex and link_status is 0 and link_speed is 10 mbps.
and also i have checked the port status in Layer 3 Switch, the port is half duplex and speed 10 mbps.
Please advice how to resove this is issue. Your reply is highly appreciable.
Regards.
R. Rajesh Kannan.

Try setting ur layer 3 switch port settings to 100FD and autonegotiate.

Similar Messages

CRS-5008: Invalid attribute value: ce0 for the network interface

Hi all,
we try to install grid infrastructure 11GR2 (11.2.0.1) into Solaris Zone with shared network interface.
We also modified scirpt racgvip, so it will be able to login (via ssh with key authorization) to the global zone and add or remove interface on zone. Script itself works fine.
But it seems that orarootagent some how checks the interface, and returned error.
In the log of the orarootagent I can see error:
2010-10-01 21:38:49.573: [ AGFW][9] CHECK initiated by timer for: ora.net1.network sapdr2db2 1
2010-10-01 21:38:50.473: [ora.net1.network][17] [check] NetworkAgent::checkLink returned false
2010-10-01 21:38:50.474: [ora.net1.network][17] [check] NetInterface::sGetIpAddress {
2010-10-01 21:38:50.474: [ora.net1.network][17] [check] netInterfaceName empty.
2010-10-01 21:38:50.474: [ora.net1.network][17] [check] NetInterface::sGetIpAddress }
2010-10-01 21:38:50.474: [ AGFW][17] check for resource: ora.net1.network sapdr2db2 1 completed with status: OFFLINE
2010-10-01 21:38:50.476: [ AGFW][17] Executing command: check for resource: ora.net1.network sapdr2db2 1
2010-10-01 21:38:50.477: [ora.net1.network][17] [check] NetworkAgent::init enter {
2010-10-01 21:38:50.478: [ora.net1.network][17] [check] Checking if ce0 Interface is fine
2010-10-01 21:38:50.479: [ora.net1.network][17] [check] NetInterface::scheckNetInterface returned 0
2010-10-01 21:38:50.480: [ora.net1.network][17] [check] CRS-5008: Invalid attribute value: ce0 for the network interface
2010-10-01 21:38:50.480: [ora.net1.network][17] [check] NetworkAgent::init exit }
2010-10-01 21:38:50.480: [ora.net1.network][17] [check] NetInterface::scheckNetInterface returned 0
2010-10-01 21:38:50.480: [ora.net1.network][17] [check] NetworkAgent::checkInterface returned false
Does anybody know how the orarootagent checks for the network resource?
It seems that there are some procedures (NetworkAgent::checkLink, NetInterface::sGetIpAddress) inside it. But the problem is that this file is binary.
Or may be there are some ways to track how orarootagent checks?

>
2010-10-18 18:11:07.589: [ora.net1.network][9] {0:2:8} [check] Checking if ce0 Interface is fine
2010-10-18 18:11:07.589: [ora.net1.network][9] {0:2:8} [check] NetInterface::scheckNetInterface returned 0
2010-10-18 18:11:07.590: [ AGENT][9] {0:2:8} UserErrorException: Locale is
2010-10-18 18:11:07.591: [ora.net1.network][9] {0:2:8} [check] CRS-5008: Invalid attribute value: ce0 for the network interface
>
Is there anything I can do with it? Will appreciate any help!Is ce0 a valid interface on the machine? (has the global zone done "ifconfig ce0 plumb"?)
Is the zone correctly configured (check output of the export sub-command of zonecfg)?
--Sowmini

Having issues after installing Essbase V9.3.1,configuring the SQL interface

I am having issues after installing Essbase V9.3.1 and configuring the SQL interface. we are using UNIX/AIX box for our Essbase server and UDB DB2 9.1 SP6 as our SQL Interface.
When tried to run an ESSCMD script to perform BUILDDIM operation on Essbase application using the load rule (with the SQL interface), got the error as recorded in the application log file and is attached at the bottom and the .odbc.ini file on the server looks as follows.
Can somebody tell me whether .odbc.ini needs any correction or what else should I do to correct the issue and able to work thru using SQL interface? Appreciate any help provided in this regard. Thanks,
.odbc.ini
[ODBC Data Sources]
DOLU003=IBM DB2 ODBC DRIVER
[DOLU003]
Driver=/home/db2inst1/sqllib/lib/libdb2.a
Database=DOLU003
[ODBC]
Trace=0
TraceFile=odbctrace.out
InstallDir=/home/db2inst1/sqllib/odbclib
[Mon Apr 20 15:16:29 2009]Local/New_Bud/Budget/Olapadm/Info(1021020)
Cannot read SQL driver name for [] from [home/hyperion/.odbc.ini]
[Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1013091)
Received Command [SQLRetrieve] from user [Olapadm]
[Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1021020)
Cannot read SQL driver name for [] from [home/hyperion/.odbc.ini]
[Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1021004)
Connection String is generated
[Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1021041)
Connection String is [DSN=DOLU003;UID=...;PWD=...]
[Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1021006)
SELECT Statement [SELECT * FROM DB2OLADM.BD_DIMENSION_DEF_PC WHERE DIMENSION_ID
= 12 ORDER BY TREE_NODE_NUM, PARENT_NODE, CHILD_NODE] is generated
[Mon Apr 20 15:16:44 2009]Local/New_Bud/Budget/Olapadm/Info(1021013)
ODBC Layer Error: [7] ==> [[DataDirect][ODBC 20101 driver]6013]
[Mon Apr 20 15:16:44 2009]Local/New_Bud/Budget/Olapadm/Info(1021014)
ODBC Layer Error: Native Error code [0]
[Mon Apr 20 15:16:44 2009]Local/New_Bud/Budget/Olapadm/Error(1021001)
Failed to Establish Connection With SQL Database Server. See log for more information
--------------------------------------------------------------------------------------------------------------------------------------------

I had similar errors when first setting up the SQL interface. Are you on a 64 bit operating system on the essbase server? If so Essbase needs to use the 32 bit odbc driver, not the default 64 bit driver.
The 32 bit driver is still available here SysWOW64\odbcad32.exe <-----This is the 32 bit (Use)
The Administrative tools by default uses system32\odbcad32.exe <----This is the 64 bit (Don't Use)
Once I opened the 32 bit driver interface directly and set it up the errors went away.

An unexpected error occurred while configuring the Network Bridge

Windows XP Pro SP2, a new TP61 6460 6WG, all Win updates, all Lenovo updates.
Everything works fine except... when I'm trying to create a network bridge I always get the following: An unexpected error occurred while configuring the Network Bridge.
This is not the situation described in Microsoft's Knowledge Base KB309640 (http://support.microsoft.com/kb/309640/en-us). I have no ICS, no ICF.
Any ideas?

I had the same problem and was really frustrated. I was about to pull my hairs out but then i was finally able to solve it. The solution is deleting some files of WMI repository. The complete details can be found on my blog http://cheatppc.blogspot.com/2008/07/unexpected-error-has-occured-while.html
Hope this solves the problem.

How to configure the network on Sun Solaris 8

The Sun workstation is a license server, and Window NT workstation need to access the license file that located in the sun workstation.
Now the Window NT workstation cannot connect with the sun solaris, and I guess that I need to configure the network on Sun Solaris 8.
Could you please tell me how to do that step by step?
If there is the system tool like the window system to configure the network easily and quickly.
I appreciate it.
Mark

If your sun system is working then probably it has network configured already .You can check it by the following command on the sun.
ifconfig -a
Generally applications asks where license server is located and you need to give the ip-address or host name only . Application docs will give more detail about it.
You can get ip-address from ifconfig comand above.
Hemant Sharma
http://www.adminschoice.com

Getting the network interface up in solaris 10

Hi,
I am a solaris newbie and am trying to get the network interface up on solaris 10. I have set the required details in
/etc/hostname.if
/etc/hosts
/etc/inet/ipnodes
/etc/inet/netmasks
/etc/defaultrouter
yet on the startup i get a message "failed to bring up IPv4 interfaces : interfacename"
And when the server starts up after giving the command "ifconfig if up"
the network interface comes up.
I need to get the interface up on the startup itself.
can anyone help me on this ?????
Thanks in advance,

... and of course, you need compatible hardware.
But you failed to tell anyone what Ethernet adapter you're trying to use.
Is it on the HCL ? http://www.sun.com/bigadmin/hcl/
If it requires third party driver software, did you install that as well ?
You failed to tell anyone whether you're installing to Solaris x86 or to Solaris SPARC.
( For example, a PeeCee NIC will generally just not work in a SPARC system. )

Why do we configure the Redundant Interface in CSS Public Face

Hi,
I have a question : Why do we configure the redundant interface in a CSS facing the public side of a CSS.
I understand the need for the interface in the server side though. Please refer to the URL below;
http://www.cisco.com/univercd/cc/td/doc/product/webscale/css/css_810/redundgd/vipredun.htm#wp1063393

this is not a requirement if your vips belong to the public vlan subnet.
But if your vip addresses are from a different subnet, then the upstream router needs a route pointing to the CSS redundant interface ip.
Gilles.

How does the terminal name the network interfaces?

I want to know the logic of the bash terminal for name the network interfaces. When I do an ifconfig there are showed multiples interfaces and I don't know which one is the WiFI, which one the Ethernet...
Thank you!

When I do an ifconfig I get this output:
lo0 Guess this is the loopback address
gif0 Don't know what is this
stf0 Don't know what is this
en0 Is the network, now in my case the wifi
en1 & en2 Guess, reading your explanation that this are the ethernet thunderbolt ports
p2p0 Don't know what is this
awd10 Don't know what is this
bridge0 Don't know what is this
Do you know what are this interfaces? If it helps I have VMware Fusion and VirtualBox installed.

Hyper-V encountered an error while Configuring the network on Vmachine

Hi all,
i am novice in window server 201, I learning from a ebook.While i doing the step of creating virtual machine , i got this error
Hyper-V encountered an error while configuring the network on Vmachine
Hyper-V encountered an error trying to access an object on computer 'localhost' because the object was not found. The object might have been deleted, or you might not have permission to perform the task. Verify that the virtual Machine Management service
on the computer is running. If the service is running,try to perform the task again by using Run as Administrator

Windows Server 201? Are you sure?
What sort of machine are you trying to install and run Hyper-V on? What OS is it running?
Bill

I bought an iphone 5s free, I try to configure the network lte ANTEL Uruguay and will not let me. How I can do? thanks

I bought an iphone 5s free, I try to configure the network lte ANTEL Uruguay and will not let me.
How I can do?
thanks

What happens when you insert the SIM card? Where did you buy this iPhone 5S? Are you sure it is not already locked to a carrier?
According to Apple, ANTEL is not a supported carrier in Uruguay - http://support.apple.com/kb/HT1937

Trying to use HPLJ 1102w as a wired network printer. How do you configure the network settings?

I have an HPLJ 1102W and I want to use it as a wired printer on my LAN. The trouble is, the easy setup utility is geared toward wireless networking and the ethernet interface will not get a DHCP address from the LAN. In order to get an IP address, I have to go through the wireless networking configuration settings. Can anyone point me in the right direction on how to use this printer as a wired network printer?
thanks,

Hi,
The HP LaserJet P1102w provide USB or wireless network interface only.
the product do not include any ethernet card, as you may also find by its spesification System Requirements below:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01999607&tmp_task=prodinfoCategory&cc=us&dlc=en...
Connectivity: Hi-Speed 2.0 USB port / Wireless 802.11 B/G (P1102w only)
Regards,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

How to configure the web interface of service desk

Hi All,
We are currently doing a configuration on solman service desk. I am on a stage where in i need to use the web interface of service desk via tcode notif_create_bsp. However, every time i call the transaction code (call the url) i cant view the web. Only an error the "Network Access Message: The website cannot be found".
I already activate needed services and already publish
SIAC_PUBLISH_ALL_INT but it still doesnt work.
I might have missed some configs/procedure on how to do it correctly.
My questions are.
1. How am i going to know the qualified domain name
of the Web AS for solman? How to configure it?
2. Can anyone give me some guide and any step by step documentation/procedure on this.
You help/suggestion will be very much appreciated
Thank you very much,
Ice

Hi,
+"Check the following 2 things. See if the port 8000 is open and in the url for the BSP in internet explorer, replace the host name with the IP address of your Solman server.+
+"+
That was a helpful tip. I change the host name with the ip address ofour solman server. However, upon login, it promts me to enter username and password. I've tried to login using my solman password but it shows an error like this.
Business Server Page (BSP) error
What happened?
Calling the BSP page was terminated due to an error.
SAP Note
The following error text was processed in the system:
Die URL enthält keine vollständige Domainangabe (10.123.161.125 statt 10.123.161.125.).
Exception Class CX_FQDN
Error Name
Program CX_FQDN=======================CP
Include CX_FQDN=======================CM002
ABAP Class CX_FQDN
Method CHECK
Line 10
Long text -
Error type: Exception
Your SAP Business Server Pages Team
Is there anything i need to configure so that i can maintan the username and password?
Thank you for your assistance,
Ice

How to configure a Network Interface?

Hey guys.
I'm very new to Solaris OS. I've now installed Solaris Express Developer Edition on my Laptop. After the restart of the installation,I find out, that my network don't work. I try to configure it with the network-admin-tool, but i can't add something, because the button "add" is nowhere in the window.
Is it possible, that Solaris don't detect the interface and how can I see it?
Thanks and sorry for the bad english :).

Look for *e[0-9] (as nge0, nge1, bge0, le0, etc.) in:
# dmesg | less
or:
# less /var/adm/messages
Exaple:
Oct 13 15:54:45 hostname nge: [ID 223987 kern.info] NOTICE: nge0: link up 100Mbps Full-Duplex
"Unplumbed" interfaces maight not show up in the kernel log as they are passive. To "plumb" all supported interfaces:
# ifconfig -a plumb
# ifconfig -a
(MS' ipconfig mimics ifconfig :o)
If it lists say 'nge0' and you don't have /etc/hostname.nge0 then:
# cat /etc/hostname.nge0
cat: /etc/hostname.nge0: No such file or directory
# uname -n > /etc/hostname.nge0
(or # echo nge0 > /etc/hostname.nge0)
Add the address to /etc/hosts and the netmask to /etc/netmasks and the defaultgateway to /etc/defaultrouter
Example:
/etc/hosts:
10.0.0.1 gw.fqdn gw
10.0.0.2 hostname.fqdn hostname nge0
/etc/netmasks:
10.0.0.0 255.255.255.0
/etc/defaulrouter:
gw
You can change things on the fly with the comands ifconfig and route, but these files must be edited for a persistent boot configuration.
You can list the entire PCI-tree with:
# prtpicl -v | less
Example:
:model Bridge device
:compatible (a2000003daTBL)
| pci10de,373.1462.7250.a2 |
| pci10de,373.1462.7250 |
| pci1462,7250 |
| pci10de,373.a2 |
| pci10de,373 |
| pciclass,068000 |
| pciclass,0680 |
:driver-name nge
To see if your interface has a driver look for the PCI to driver-mapping in /etc/driver_aliases. Also check http://www.sun.com/bigadmin/hcl/ and http://www.sun.com/bigadmin/hcl/hcts/install_check.html
(put /sbin and /usr/sbin in PATH, i.e. PATH=$PATH:/sbin:/usr/sbin;export PATH)
(use "more" if you don't have "less")

In Multimapping how can we configure the Receiver , Interface Deter for BPM

Hi Friends ,
I am trying the the BPM scenario using Integration Process
BpmPatternCollectTime
from SAP BASIS ® SAP BASIS 7.00 in the namespace http://sap.com/xi/XI/System/Patterns
I have done the scenario like the above . I have followed all the Steps which are used in above scenario.
I am using a File Sender Adapter and Receiver Adapter .
It is Successfully picked up the File but nothing is happening after that .
I am using two receiver Determination one from Ob to IP and other from IP to FIleReceiver ( IB) .
But, I am Getting error as Block1 (No agent) Error in the PE graphical diagram
I have checked in SWWL my Integration Process Return code is "0"
The steps Which i have followed in BPM are
1. Block with Deadlkine branch and Exception handler( as TimeOut Exception)
Block Start and Block End as New Transaction
2. Inside Block infinite Loop which contains Receive step ( Actives the Correlation ) and Multiline Container element which appends the Messages with CollectMessage
3. Transformation Step
It creates the New Transaction and Interface Maping from CollectMessage List to New Mesage
4. Send Step
It sends the New Message . It creates the New Transaction .
Can you Please tell me how to configure the Receiver and Interface Determination for the above scenario ?
Regards.,
V.Rangarajan

Hi Ranga
have a look at these
you can ref: this link to find example where a receiver determination step is used in BPM- http://help.sap.com/saphelp_nw04/helpdata/en/43/6211b11c895f6ce10000000a1553f6/content.htm
More abt RD step in BPM - http://help.sap.com/saphelp_nw04/helpdata/en/14/d5283fd0ca8443e10000000a114084/content.htm
if useful pls reward

Udev swapping the network interfaces [solved?]

After a recent upgrade my network devices (eth0 and eth1) seem to be randomly assigned at boot. This obviously causes problems for the network scripts. I tried to rectify this by specifying the device names via udev:
/etc/udev/rules.d/10-network.rules
KERNEL="eth*", SYSFS{address}="00:0d:70:a8:63:12", NAME="eth0"
KERNEL="eth*", SYSFS{address}="00:0b:a1:18:80:ba", NAME="eth1"
but this does not seem to have any effect on the device names. Anyone aware of how to fix this problem or what exactly is causing it?
*note*
I manually searched through the first couple of pages of this forum before posting this because I figured others would have this problem and forum search currently does not work for me. Sorry if this is a duplicate.

brain0 wrote:
KERNEL="eth*", SYSFS{address}="00:0d:70:a8:63:12", NAME="eth0"
This is your udev line. And now compare it to this one:
KERNEL=="eth*", SYSFS{address}=="00:0d:70:a8:63:12", NAME="eth0"
See the difference? Stare at it until you see it.
I'd also reommend this change:
SUBSYSTEM=="net", SYSFS{address}=="00:0d:70:a8:63:12", NAME="eth0"
It makes this rule more general and even works if the interface is named completely different by the kernel.
Thank you! I copied that bit I had above (except for the MACs) from a howto page on udev. I guess they changed some things recently to require double equals for comparison? I had to go back and change some of my rules for other things as well.

Configuring the Network interface settings in E250

Similar Messages

Maybe you are looking for