Confused between Region & Location

 confused between the Region & Location read many docs bet again confusion increases.

what documents you have been reading Vijay :-)
Anyways, in simple terms, Regions help you select codecs for calls between two regions. You specify codec bandwidth 8kbps, 64kbps etc. for calls between two regions, so the calls between those region will use the codec equivalent to that bandwidth or less than that. for example, if you setup bandwidth to 8kbs, it will use G729, ilbc etc but never use G711.
While location is used for CAC (call admission control), i.e it specifies maximum amount of bandwidth for a location, which will in turn determine total number of on-net calls that can be made over WAN from that site. If anymore calls are made either calls are rerouted through PSTN if AAR is enabled (or calls fail)
Basically its a QoS mechanism used to control number of audio and video calls that could be made over a particular site's WAN link, to avoid over-subscription of WAN link and preserve quality of the calls.
-Terry

Similar Messages

  • Confused between delivery,shipping and shipment

    Hi Gurus,
                   While going through SD flow, I just confused between shipping, delievery and shipment. Can you please explain the complete process and tell me what exactly we do in shipping, delievery and shipment.
    My e-mail id is [email protected]
    Thanks and Regards
    Rajat Garg

    Hi Rajat,
    Shipping:
          shipping activities perform before delivering the goods to the ship to party,
    like time take to pick the goods, packing of those goods into carts ( as per the its packing system), loading this packed goods into truck ( or any vehicle which uses to ship the goods).
    Delivery:
    starting from the shipping point,how much time taken to reach the customer,
    might be travelling time, stages like,if itz through Air, initially this load should go airport, from there customer country , n frm there to actual ship to party location.
    Transporation:
            Moving of the goods, in which transporation mode, as we have roadways, railways, by air,
    how many stages involved ( itinaries), from which route,all  comes into transporation.
    <a href="http://help.sap.com/saphelp_47x200/helpdata/en/d5/2285347860ea35e10000009b38f83b/frameset.htm">Transporation</a>
    hope this adds info
    *reward points

  • I have purchased a new iPad and given my old one to my husband.  How do I change the Apple ID over to him.  We are having continuous confusion between the two iPads

    I have purchased a new iPad and given my old one to my husband.  How do I change the Apple ID over to him.  We are having continuous confusion between the two iPads

    Hi Marg42,
    Thanks for visiting Apple Support Communities.
    First, your husband can create his own Apple ID via the web, computer, or iPad, if he hasn't already:
    My Apple ID
    https://appleid.apple.com
    iTunes: How to set up an Apple ID within iTunes
    http://support.apple.com/kb/ht2731
    Next, he can sign out of the Apple services that are currently using your Apple ID on your old iPad, and sign in with his own.
    This article has instructions for doing so for specific Apple services:
    Apple ID: What to do after you change your Apple ID
    http://support.apple.com/kb/HT5796
    Alternately, he can erase the device and set it up as new using the steps in this article:
    iOS: How to back up your data and set up your device as a new device
    http://support.apple.com/kb/ht4137
    Best Regards,
    Jeremy

  • HT1379 The USB ports on my 30" Cinema are not working.  The monitor has not been used for a year or so, and the computer is a Mac Book Pro, 1012 model running OS Mavericks.  I need to move the computer between two locations, and the other monitor is a 27"

    The USB ports on my 30" Cinema HD display appear to not work.  The monitor has not been used for almost a year, when I upgraded to a new Mac Book Pro and the 27" retina display.  Now I need to move the computer back and forth between two locations using the two displays.  The need for operating USB ports is essential.  Any ideas.  The display appears entirely normal.  Am running OS X 10.9.

    Disregard, problem solved.

  • Transfer posting between storage location

    Hi
    2 questions: we are going to create a new storage location to make material movements:
    1- We have to move stock between storage location.
    Storage A(new): without WM
    Storage B: under WM.
    We would like to know wich is the best practice to do the transfer: MB1B? 301/311 movement type?
    2 -  If we decided to create a new storage location with WM. Wich are the recomendations or the points we have to consider:
    Under the same Warehouse numer? A knew storage type? Wich are the activities in SPRo?
    Thanks in advance for the help
    Regards
    Enzo

    http://help.sap.com/saphelp_erp60_sp/helpdata/en/4d/2b90dc43ad11d189410000e829fbbd/frameset.htm
    If it is the same physical Warehouse you could use the same Warehouse, otherwise a new or no Warehouse.
    If the Storage Locations are near by and stock doesn't cross public roads and it's manually initiated, suggest just use a one step as it's the simplest process.
    If there's a significant distance but on-site use two-step or if stock transferred by public roads, use STO.

  • Define Shipping Data for Stock Transfers Between Storage Locations

    Hi Guru,
    Can i know what is the purpose to maintain Customer, SHipping data for each storage location for the STO between storage location?
    Purchasing --> Purchase Order -->
    Set up Stock Transport Order-->
    Set Up Stock Transfer Between Storage Locations-->
    Define Shipping Data for Stock Transfers Between Storage Locations

    The Sales org, Distribution channel, Shipping point, Vendor and Customer are maintained to created the delivery.
    It is for the transfer of stock between storage locations with any movement type.
    Eg: When you do a 311 movement type from Sloc A to Sloc B, then it will create a inbound delivery with the Vendor specified for Sloc A and an outbound delivery from Sloc B with the Customer specified assuming the customer and the vendor as the Plant.
    You have to create a internal Vendor and Customer.
    Hope it helps.

  • Stock transfer between storage locations and lead time

    Hello,
    We use stock transfer orders between different storage locations. Is it possible to maintain the transport lead time between storage locations somewhere or do in need to use routes and scheduling?
    rgsd
    GAR

    Hi,
    Try using movement type 313 and 315
    313 -- Transfer posting SL to SL --- Remove from issuing SL
    315 -- Transfer posting SL to SL  -- Placing in Receiving SL
    Regards

  • Add horizontal spaces between regions

    Hi everyone,
    We use APEX 4.2.
    I want to know if it's possible to add horizontal spaces between "region a" and "region b" ?
    How I can do this ? I don't want to add an extra "region c".
    I taught about adding something in the header region or in the footer region.
    Thanks in advance. Have a great day.

    Hi,
    You could add some css to the first (left?) regio.
    .rounded-corner-region {margin-right: 50px;}*.rounded-corner-region* depending on the selected regio.
    Regards,
    Kees Vlek
    <tt>Company: http://www.orcado.nl
    Blog: http://www.orcado.nl/blog/blogger/listings/69-kvlek
    Twitter: http://www.twitter.com/skier66</tt>
    If the question is answered please change it to answered and mark the appropriate post as correct/helpfull.

  • DataSource - difference between ejb-location and location

    Hi,
    Does anyone know difference between ejb-location and location attribute specified in datasources.xml for an emulated datasource.
    There are few connection leakage errors reported in log files though the connection and other database objects have been closed in finally block in all places.
    So just wanted to find out whether specifying the same value for location as well as ejb-location is not the root cause of connection leakage errors.
    Thanks in advance for any help.
    Regards,
    Smita

    Smita,
    Personally, I think you should make sure that all locations (in your "data-sources.xml" file) should be different -- although I can't tell you why.
    According to the documentation, the "ejb-location" uses a connection pool and I exclusively use the "ejb-location".
    Good Luck,
    Avi.

  • Stock transfer between storage location in IS -Retail

    Hi,
    I want to have a Stock transfer order between two storage locations in the plant.
    I have activated the "Activate Stock Transfer Between Storage Locations", now i can create a STO and have the "Issuing SLoc" tab.
    Having that i get an error message "Not possible to determine shipping data for material XXX" Message no. 06280.
    I am trying to have the shipping data in customizing for set stock transfer  - "Define Shipping Data for Plants", but my site is not listed due to the use of IS Retail. Is there a way to configure it?
    Tnx
    Lior

    Hello Lior,
    in Retail your distribution center is a vendor and a customer, and your store is a customer. Therefore when you create master data for your distribution centre and store, you also create the vendor and customer masters that are required.
    By this link of the DC / Store to the customer master the shipping data is derived. I hope this answers your question.
    If you have further queries related to this, please do post them.
    Regards,
    Smitha

  • Stock Transfer between Storage Location with Order

    Dear MM experts, 
    I am into SAP SD.
    Our client wants to Transfer Stock from one Storage Location to another Storage Location of the same Plant. (This can be easily done thru MB1B via Transfer Posting)
    But the unique requirement here is they require some kind of Delivery Order or Tansfer Order to be created first & only based on that document user can transfer Stock between Storage Locations of a same Plant. (Similar to Inter-Plant Stock Transfer where we create Stock Transfer PO & then move goods between plants).
    Can you please suggest on how to achieve the above scenario.
    Thanks,
    Jignesh Mehta
    Mumbai

    hi
    Stock Transfer between Storage Locations
    u2022 Function of stock transport orders between storage locations is available from ECC 6.0 onwards.
    u2022 As a result of which user can input issuing storage location with supplying plant.
    u2022 Facility of using different delivery types for different issuing storage locations is available.
    u2022 Shipping Point data can also be determined based on the issuing storage location.
    refer following
    http://sapfunctional.com/MM/StockTransfer/Configure.htm
    http://help.sap.com/saphelp_scm41/helpdata/EN/23/29cf20eabe094e957763a46aa5be9d/content.htm
    regards
    kunal

  • Transfer between storage location to storage location within same plant

    Dear Gurus,
    We r doing storage location to storage location transfer within same plant through purchase order.
    Due to excise requirement we have to raise excise invoice for the same for captive consumption purpose.
    Is it possible to make it One step procedure so that GR will take place at same time as GI the way it works for plant to planrt.
    In ECC 6.0 option is there for transfer between storage location. I configured but it is not working.
    Please check the same.
    Rgds,
    Saurabh

    Hi Saurabh,
    The proceedure you are following is a bit wierd. But I think this is as per your business requirements.
    You can continue to follow the same proceedure as this may  not be possible through one step movement type.
    Best Regards,
    Prateksha.

  • STO Between Storage location configuration

    Hi,
    We are using STO configured for Plant to Plant stock transfer.
    Now we wish to configure STO between Storage Location
    We wish to know whether STO between Storage locations can be used along with STO between Plants.
    We are in ECC 6.0.
    Regards,
    Kiran

    Hi Kiran,
    Yes, you can use STO with plant to plant as well as STO with st.loc to st.loc. but the plants have to be differnet plants.
    Check the customizing for st.loc. sto in ECC 6.0
    Cheers,
    Satish Purandare

  • Synchronize data between difference locations, help me !!!

    Hi gurus,
      I want to synchronize data between difference locations, I used merge replication function in SQL server 2000, but after run, my SBO can't to use publication database and subcripber database. Pls tell me why and how to solve it !?!? Or anybody have another method for the synch, pls give me. Thanks for any idea !!! I'm using SBO 2005A

    Hi Andy,
    What you are trying to do is not allowed. As you have already see, the result database could be non usable.
    There are several options for this scenario. For example:
    1- Use Copy Express to copy data from one location send it to the other and insert it again using Copy Express. You could try to make it automatic.
    2- Use SAP B1i . You have a document about it here. You have also a new forum about it:
    3- Some integration tool such us Magic IBolt which lets you compose the relations betwen the different locations. This looks like a good tool, but must be paid.
    Deciding between this options (and any other I haven´t mention) is not an easy work.
    Regards,
    Ibai Peñ

  • Iphone maps 3g "transit directions could not be found between these locations"

    RE: iphone maps 3g "transit directions could not be found between these locations"
    My kitten (Mr. Kitty or Mister K Star), who I had just adopted from the SPCA (died on August 14, 2011) -- which has really put my mental state all over the kitten place (shopping, in a car, in public ...) ... I only had the poor guy for one month and he died of pneumonia.
    Me driving in my vehicle has not been the same.
    EXAMPLE:
    I was driving in my car yesterday. And then today, I realized I could not get from point A to point B on my iphone G3. Well, I called AT & T and explained my situation. The guy ( AT & T rep ) told me that the "Maps" feature got bought out and it does not work. I thought to myself, "That's F-ing stupid." That will pee off infinite Apple iPhone users.  Expressed, "I have been using Google Maps on my iPhone 3G ever since I got it." Asked, "are any other iPhone customers calling in having the same issues?"
    Of course, I'm smart. I took a screen shot ("transit directions could not be found between these locations"). I was too busy to even notice that the icons at the top were on the "Bus" image. Duhhhhh. Only thing I can say, is ... that when I am driving in my car ... I'm multi-tasking. Some where in my drive (adventure), I accidentally touched the "Bus" icon like an idiot.
    Therefore, when I tried to get one simple answer to help with my problem when dialing 611, the people (at AT & T) could not even provide a correct one just reading from a manual while on the job.
    Luckily, my screen shot helped me out. It was the only way to go online and find this post from 2009. Then I had to re-look at my screen shot to even see that my "Bus" image was highlighted. So I just put the icon back onto the "Car."
    https://discussions.apple.com/thread/2001991?start=0&tstart=0
    >^.^<
    Next time my weird self drives in my car, I need to remember, "Look at the top icons. Make sure it's on the 'car' and not the freakin' 'Bus' icon. LOL!!!!!"
    Out of the past years I've had this phone, I can't wait to buy a new G5 this year.
    ~Agent out~
    Message was edited by: ratsrocknroll

    it doesn't provide also to Saudi Arabia and UAE some gulf countries it doesn't provide directions in it
    so i have to buy a program to get the directions in this countries ?

Maybe you are looking for