Connect 2 i88x together

anybody know how to do this?

Hi, I have not managed to get one i88X working with Logic 8 and I was wondering if you could help.
I have connected the i88X to the Mac and can play music from iTunes and output sound from Logic, but I am trying to input audio from my i88X to Logic and it is not working. I am probably missing a basic setting, but if you could help then it would be most appreciated.

Similar Messages

Connecting switches together

hi,
What is the best way to connect switch together (with 2960 switch)..cross or stright cable...up/down or normal port ?
WAN ----Router 1 --- -SW1 ---- SW2
                                  |
                                  |
                                 SW3----SW4----SW5 (no vlan)---PC1
all switch has up,down and normal port except SW5
Does SW5 will support vlan if it is connect to a layer 2 switch (let s say sw5 is connected to port 5 of SW4 (and port 5 is VLAN 20 access mode...then trunk between SW3 and SW1))...is there any inheritance ?
Hope, this time, this post will be post on the forum.
Thanks for help,

Hi Loic the wire between switch 4 and 5 shouldn't make a difference in terms of rj45 so long as it is auto set (which by default it is). If you want switch 5 to be vlan 20, configure vlan 20 there and the port on switch 4 must also have vlan 20. So long as either switch is tag or untag, but both configuration matching it will work fine.
-Tom
Please mark answered for helpful posts

HP LP2065- Need to connect 2 together for extended view

Hi,
I'd like to connect 2 HP LP2065 monitors together for extended viewing. ( Dragging files from one screen to another, not mirroring ). Can this be done without a Dual Monitor KVM switch? Thanks for any feedback or help in advance.
Note:
I currently run 1 HP LP2065 monitor with 2-3 laptops using a 4 port single monitor KVM switch. This set up works fine for one monitor. Online forums suggest getting a Dual Monitor KVM switch to run 2 monitors. But those switches cost $225 plus. And I can score another used HP LP2065 for less than $75

My first thought would be to add the Radeon 2600, it does work in 2007 models running Leopard. And the cost is acceptable.
As long as the X1900 is fine, no need to swap out for the newer 3870 just yet.

Is wrt120n wireless router compatable with befsr41 ver 2 router to connect them together?

i cant get it to work with my other router and i need to because i have 5 things to connect to the internet and network.
Thanks
Gary
Solved!
Go to Solution.

Connect two routers together here. Or go buy a $20 4 port switch and just plug it in.
Message Edited by sabretooth on 01-14-2010 09:20 PM

Sudden loss of connection all together

I'll start off by saying hello to everyone.
We've had infinity installed for some time now. I'm talking many months, definitely more than 18. This is the first time we have encountered a sudden loss of internet connection. We have already called BT and followed all their steps but what the people at the call centre don't understand is we want to know WHY! Not the possibilities, a solid reason. I was always able to give this to our business customers when I worked first line support. We recently had a storm which I think is contributing, since going over everything many times and no joy I have wondered about the phone line. Since the loss of connection it has always got massive static interference on the line. The service updates say all is good, but I can't help but think that page is just nonsense and that it is at fault and that BT are too up themselves to admit the fault is their end.
Can anyone shed some light on this for me?
Thank you very much in advance.

Is anything shown here. http://usertools.plus.net/exchanges/mso.php
http://usertools.plus.net/exchanges/?
http://btbusiness.custhelp.com/app/service_status
http://bt.custhelp.com/app/answers/detail/a_id/15036
http://community.plus.net/exchange-information/
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

I want to connect ecc 6.0 server and SOLMAN server together

Hello All , I need your help please ,
I`m working on ecc 6.0 on windows server 2008 R2 and i want to upgrade some components via EHPI ,
So after reading i reached that I need to install SOLMAN on another seperate server to generate the XML stack files for EHPI from t-code " mopz " .
I`ve installed the SOLMAN on another server " windows server 2008 R2 " , and succsesfully finished .
Now i have two seperated servers one for ECC and the other one for solution manager 7.1 .
NOW I NEED to connect the two servers together to let them see each other .
How Can I Connect them together Step by step Please ???
Hope to help Immedietly And thnx in advance.

Hi Rami,
Once the basic configurations are done. It will be just 30 minutes sufficient to complete the connections between Solution manager and ECC 6 system.
http://help.sap.com/saphelp_bpc70sp02/helpdata/en/83/47421d68ea497fb7b813e17843122d/content.htm
Above link for the same.
You should create ECC system in solution manager as below link
http://help.sap.com/saphelp_bpc70sp02/helpdata/en/45/56dd10b5f62a50e10000000a11466f/frameset.htm
Set SUser id to solution manager which comes under the basic settings.
http://help.sap.com/saphelp_bpc70sp02/helpdata/en/45/56dd10b5f62a50e10000000a11466f/frameset.htm
Maintain SAPOSS RFC connection, hope you have an SAPROUTER setup for your company.
Please let us know if you are facing any issues.
Thanks
Jaianandh V

Speaker wire cut, want to fix myself - which is the best way to connect the wires back together?

Some how, one of the wires going to my left-center speaker got cut in half. Not sure if it was the vacuum or my dog........anyway, I want to fix it, so - would you recommend butt-connectors, soldering the wire back together, or some other method?
Also, does it matter which wires connect back together? The wires are identicle (smooth covering) and both wires appear to be copper........ I was just wondering if anything would happen if you were to connect the wires back together, but backwards.
Please let me know so I can get this fixed quickly.
Thanks,
-Officer_Dufus

http://www.eminent-tech.com/music/multimediatest.html
Go to the above link and listen to the Pink Noise Monaural and the Pink Noise with Reversed Polarity tests. When a speaker is of opposite polarity, that means that the wires are connected backwards (positive to black and negative to red). If this happens, when your speaker should move out it'll move in and vice versa. This makes the sound seem to come from everywhere but the speaker. Play the tests to see what I mean.
If you solder your wires back together and notice this problem with your speaker, just reverse the connection to the speaker itself and you should be okay.

Connecting 2 imacs together

I have a new desktop and a "not as new" desktop. I'd like to use the older mac as a second monitor for the new imac. Is it possible to connect them together and only use the new hard drive? If so, how?

I believe that only works in the reverse. See Using a 27-inch iMac as an external display.

Help to connect 2 switches together

Hi
I need your help to can i make 2 switches 2950 and 2960 connecting it together through trunk port,so in my question is what the command that should be on the trunk port???
I wrote the below command but it's not acceptable:
Switch(condig-if)#switchport trunk encapsolation isl

abakrbshat wrote:Hi,thanks for your responseI did that right now but still the pc unable on the ping to other pc in other switch
Do the interfaces on the switches come up when connected? What do you get when you input "show interface X/Y" on each switch?
Are the source and destination PC in the same VLAN (1 by default, something else if it's been changed), and have IP addresses in the same subnet?
And, lastly - are they Windows boxes? If so, do you have the firewall turned OFF? Recent Windows boxes seem to block PING by default unless you tell them otherwise.

Connecting two Socket together

Hi everyone !
Here is my little problem :
I have two objects in a software. Each of them have a Socket, and i need to connect them together.
How can i do that ? it seems i could with a ServerSocket, but ... is there an other way ?
If anyone has an idea ...
Thanks.

Here are more precisions :
I've just made a try on something. Here is a little piece of code :
<pre>
import java.io.*;
import java.net.*;
class Obj{
public InetSocketAddress address;
Socket s;
String name;
public Obj(String n, int port) throws Exception {
name = n;
address = new InetSocketAddress("127.0.0.1",port);
System.out.println(name + " : port " + address.getPort());
s = new Socket();
public void connect(Obj o) throws Exception {
s.connect(o.address);
public static void main(String[] args) throws Exception {
Obj obj1 = new Obj("objet1",2001);
Obj obj2 = new Obj("objet2",2002);
obj1.connect(obj2);
</pre>
And the result is :
Exception in thread "main" java.net.ConnectException: Connection refused
Well, i guess this comes from the fact that my Socket in Obj1 is not ready to recieve a connection ... is there something similar to the method accept() of ServerSocket for the sockets ?

Connecting two 5k's together

Hi,
How do we best connect our two 5596's together for redundancy and multipathing, both physically and configuration-wise? I see information about vPC's in the manuals, but I'm not sure if this is really what we need to do. We have a simple design--just servers connecting to the 5596's via fc, then the 5596's connecting to our storage via fc. Thanks!

If you are using these for FC SAN connectivity and no Ethernet then you do not need vPC as it is for providing Ethernet port channels across 2 switches.
For FC only you would treat them just like MDS switches. You will not connect them together and each should be in their own VSAN.
The SAN will connect to both and your servers will connect to both.
Your servers will need SAN multipathing software to provide load balancing and redundancy

Connecting two macbook pros together to form an extended desktop

I have two macbook pros and I wanted to connect them together to form an extended desktop. How would I go about doing that. I already have them connected together for file sharing. But I want to connect them to form an extended desktop.

Use a product such as ScreenRecycler over your existing network.
(112192)

Connecting Two ASAs together via local interface

Hi
I have two cisco ASA routers & wish to connect them together so that traffic between is permitted with out going outside interface.
Two asa are located at in ONE office and two have separate internet connection (ISP) configured.
So here is what I did so far.
configure one of the interface on each ASA with some IP adddress.
ASA 1 ------- interface 0/6 10.1.1.1 (ASA X 1512)
ASA 2 --------- interface 0/5 10.2.2.2 (ASA 5055)
now connected a Ethernet cable to these inferface.
I was able to addd a route on asa 2.
route add interface0/5 10.1.1.0/24 10.2.2.2
but when I add route on ASA 1 I get the following error.
route add interface0/6 10.2.2.2/24 10.1.1.1
%invalid next hop address it belongs to one of our interface.

Sorry if I was not clear
I have two separate ISPs connecting two two separate ASAs.. Two asa are now connecting separate LANs.
Now I want to communicate between LANs.
So I connected an ethernet cable bw ASAs and trying to configure the route.
But not able to establish
Here is the configuration of ASA where I am faceing problem, while trying to add route
route add voice-interface 10.1.1.1/24 255.255.255.0 10.2.2.2 1
I get error says
route already exsists
interface GigabitEthernet0/0
nameif outside0
security-level 0
ip address 0.2.5.2 255.255.255.252
interface GigabitEthernet0/1
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/2
nameif inside2
security-level 100
ip address 192.168.1.1 255.255.255.0
interface GigabitEthernet0/5
nameif voice-interface
security-level 100
ip address 10.1.1.1 255.255.255.0
object network NETWORK_OBJ_12.1.3.0_2
subnet 12.1.3.0 255.255.255.0
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object network OBJ_ALL_NETWORK
subnet 0.0.0.0 0.0.0.0
description Any Network
object network voice-asa-network
subnet 10.2.2.0 255.255.255.0
object network 10.1.1.1
host 10.1.1.1
access-list outside0_cryptomap extended permit ip 192.168.1.0 255.255.255.0 12.1.3.0 255.255.255.0
access-list inside2_access_in extended permit ip 192.168.1.0 255.255.255.0 any
nat (inside2,outside0) source static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 destination static NETWORK_OBJ_12.1.3.0_24 NETWORK_OBJ_12.1.3.0_24 no-proxy-arp route-lookup
object network OBJ_ALL_NETWORK
nat (any,outside0) dynamic interface
route outside0 0.0.0.0 0.0.0.0 0.2.5.2 1
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec security-association pmtu-aging infinite
crypto map outside0_map 1 match address outside0_cryptomap
crypto map outside0_map 1 set pfs
crypto map outside0_map 1 set peer 9.2.5.1
crypto map outside0_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside0_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside0_map interface outside0
crypto ca trustpool policy
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
threat-detection basic-threat
threat-detection scanning-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl encryption aes128-sha1 3des-sha1
group-policy GroupPolicy_6.2.5.1 internal
group-policy GroupPolicy_6.2.5.1 attributes
vpn-tunnel-protocol ikev1 ikev2
class-map inspection_default
match default-inspection-traffic

SCVMM losing connection to cluster nodes

Hey guys'n girls, I hope this is the right forum for this question. I already opened a ticket at MS support as well because it's impacting our production environment indirectly, but even after a week there's been no contact. Losing faith in MS support there
The problem we're having is that scvmm is that a host enters the 'needs attention' state, with a winrm error 0x80338126. I guess it has something to do with the network or with Kerberos, and I've found some info on it, but I still haven't been able to solve
it. Do you guys have any ideas?
Problem summary:
We are seeing an issue on our new hyper-v platform. The platform should have been in production last week, but this issue is delaying our project as we can't seem to get it stable.
The problem we are experiencing is that SCVMM loses the connection to some of the Hyper-V nodes. Not one
specific node. Last week it happened to two nodes, and today it happened to another node. I see issues with WinRM, and I expect something to do with kerberos. See the bottom of this post for background details and software versions.
The host gets the status 'needs attention', and if you look at the status of the machine, WinRM gives an error. The error is:
Error (2916)
VMM is unable to complete the request. The connection to the agent cc1-hyp-10.domaincloud1.local was lost.
WinRM: URL: [http://cc1-hyp-10.domaincloud1.local:5985], Verb: [ENUMERATE], Resource: [http://schemas.microsoft.com/wbem/wsman/1/wmi/root/cimv2/Win32_Service], Filter: [select * from Win32_Service where Name="WinRM"]
Unknown error (0x80338126)
Recommended Action
Ensure that the Windows Remote Management (WinRM) service and the VMM agent are installed and running and that a firewall is not blocking HTTP/HTTPS traffic. Ensure that VMM server is able to communicate with cc1-hyp-10.domaincloud1.local over WinRM by successfully
running the following command:
winrm id –r:cc1-hyp-10.domaincloud1.local
This
problem can also be caused by a Windows Management Instrumentation (WMI) service crash. If the server is running Windows Server 2008 R2, ensure that KB 982293 (http://support.microsoft.com/kb/982293)
is installed on it.
If the error persists, restart cc1-hyp-10.domaincloud1.local and then try the operation again. /nRefer to
http://support.microsoft.com/kb/2742275 for more details.
Doing a simple test from the VMM server to the problematic cluster node shows this error:
PS C:\> hostname
CC1-VMM-01
PS C:\> winrm id -r:cc1-hyp-10.domaincloud1.local
WSManFault
    Message = WinRM cannot complete the operation. Verify that the specified computer name is valid, that the computer is accessible over the network, and that a firewall exception for the WinRM service is enabled and allows access from this
computer. By default, the WinRM firewall exception for public profiles limits access to remote computers within the same local subnet.
Error number: -2144108250 0x80338126
WinRM cannot complete the operation. Verify that the specified computer name is valid, that the computer is accessible over the network, and that a firewall exception for the WinRM service is enabled and allows access from this computer. By default, the WinRM
firewall exception for public profiles limits access to remote computers within the same local subnet.
I CAN connect from other hosts to this problematic cluster node:
PS C:\> hostname
CC1-HYP-16
PS C:\> winrm id -r:cc1-hyp-10.domaincloud1.local
IdentifyResponse
    ProtocolVersion =
http://schemas.dmtf.org/wbem/wsman/1/wsman.xsd
    ProductVendor = Microsoft Corporation
    ProductVersion = OS: 6.3.9600 SP: 0.0 Stack: 3.0
    SecurityProfiles
        SecurityProfileName =
http://schemas.dmtf.org/wbem/wsman/1/wsman/secprofile/http/spnego-kerberos
And I can connect from the vmm server to all other cluster nodes:
PS C:\> hostname
CC1-VMM-01
PS C:\> winrm id -r:cc1-hyp-11.domaincloud1.local
IdentifyResponse
    ProtocolVersion =
http://schemas.dmtf.org/wbem/wsman/1/wsman.xsd
    ProductVendor = Microsoft Corporation
    ProductVersion = OS: 6.3.9600 SP: 0.0 Stack: 3.0
    SecurityProfiles
        SecurityProfileName =
http://schemas.dmtf.org/wbem/wsman/1/wsman/secprofile/http/spnego-kerberos
So at this point only the test from the cc1-vmm-01 to cc1-hyp-10 seems to be problematic.
I followed the steps in the page
https://support.microsoft.com/kb/2742275 (which is referred to above). I tried the VMMCA, but it can't really get it working the way I want, or it seems to give outdated recommendations.
I tried checking for duplicate SPN's by running setspn -x on affected machines. No results (although I do not understand
what an SPN is or how it works). I rebuilt the performance counters.
It tried setting 'sc config winrm type= own' as described in [http://blinditandnetworkadmin.blogspot.nl/2012/08/kb-how-to-troubleshoot-needs-attention.html].
If I reboot this cc1-hyp-10 machine, it will start working perfectly again. However, then I can't troubleshoot the issue, and it will happen again.
I want this problem to be solved, so vmm never loses connection to the hypervisors it's managing again!
Background information:
We've set up a platform with Hyper-V to run a VM workload. The platform consists of the following hardware:
2 Dell R620's with 32GB of RAM, running hyper-v to virtualize the cloud management layer (DC's, VMM, SQL). These machines are called cc1-hyp-01 and cc1-hyp-02. They run the management vm's like cc1-dc-01/02, cc1-sql-01, cc1-vmm-01, etc. The names are self-explanatory.
The VMM machine is NOT clustered.
8 Dell M620 blades with 320GB of RAM, running hyper-v to virtualize the customer workload. The machines are
called cc1-hyp-10 until cc1-hyp-17. They are in a cluster.
2 Equallogic units form a SAN (premium storage), and we have a Dell R515 running iscsi target (budget storage).
We have Dell Force10 switches and Cisco C3750X switches to connect everything together (mostly 10GB links).
All hosts run Windows Server 2012R2 Datacenter edition. The VMM server runs System Center Virtual Machine Manage 2012 R2.
All the latest Windows updates are installed on every host. There are no firewalls between any host (vmm and hypervisors) at this level. Windows firewalls are all disabled. No antivirus software is installed, no symantec software is installed.
The only non-standard software that is installed is the Dell Host Integration Tools 4.7.1, Dell Openmanage Server Administrator, and some small stuff like 7-zip, bginfo, net-snap, etc.
The SCVMM service is running under the domain account DOMAINCLOUD1\scvmm. This machine is in the local administrators group of each cluster node.
On top of this cloud layer we're running the tenant layer with a lot of vm's for a specific customer (although they are all off now).

I think I found the culprit, after an hour of analyzing wireshark dumps I found the vmm had jumbo frames enabled on the management interface to the hosts (and the underlying infrastructure does not).. Now my winrm commands started working again.

Questions about using FILE adapter to connect to other systems

Hi,
in my PI scenario i am facing a problem in usage of the file adapter.
Our PI system is installed on a UNIX server. The target system for upload an download files is a WINDOWS system. The software installed on the WINDOWS system is only able to export the needed file lokal on the WINDOWS server.
Between UNIX systems i can connect a together used fileshare folder. But this won´t help me in my UNIX <> WINDOWS scenario.
I thougt on using an FTP server on the WIDNOWS system to make the PI able to connect via the FTP adapter but this works fine for one or two systems. I don´t think that this ist the best solution when connection to a lot WINDOWS systems, but mayby i am wrong.
Actually i use UC4 to copy the files between the two systems.
Any ideas how to deal generally with such scenarios?
Many thanks
Michael

Even though if you map Unix and Windows OS to read the files, in the long run the design will put you in trouble. Means it requires constant support. Better you go with unix script as per the above suggestion.
Regards
Pothana

Connect 2 i88x together

Similar Messages

Maybe you are looking for