Connect AirPort Extreme to my FritzBox internet router

How can I connect the AirPort Extreme to my FritzBox Router ? I bought the AirPort extreme to get a better receiption in the back area of my appartment.
Do I have to connect the AirPort Extreme to my normal router at all ?

since i tried to move it into another end of
the appartment and now the orange light blinks and
it gets no data.
do you have an idea how i can fix this problem?
Unfortunately, I do not think that you understood my answer above.
you need to establish a permanent wired Ethernet connection from one of the LAN <-> ports on the FritzBox router to the WAN "O" port on the AirPort Extreme.
Permanent means that the AirPort Extreme must remain wired to the Fritzbox router at all times.

Similar Messages

How do I connect Airport Extreme to U-verse Internet Gateway: Motorola Model NVG510

I tried to set up a new network with the Airport Extreme and get no Internet connectivity from the AT&T gateway. The Extreme network sets up fine and I can access it from all my devices, but no Internet.
What am I doing wrong?
Thanks,
Mick Jones

It will only take a minute to check the Ethernet cable. Just connect it from a LAN <-> port on the Uverse gateway to the Ethernet port on a computer. Turn off the wireless on the computer and see if you can get a good Internet connection that way.
If you can, great. You cannot, then you either have a bad Ethernet cable or the port on the gateway may not be working correctly.
Power up the AirPort Extreme for a few minutes
Then, hold in the reset button on the AirPort Extreme for 10-12 seconds and release
Allow a full minute for the AirPort to restart
Connect the Ethernet cable from a LAN <-> port on the Uverse gateway to the WAN "O" port on the AirPort Extreme
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on Other WiFi Devices
Click AirPort Extreme
The utility will open up automatically, take a minute to analyze things, then suggest that the AirPort will be configured to create a new network. The window will look like the example below, except that you will see an AirPort Extreme instead of an AirPort Express.
Network Name......type in a short, simple name that you want to call your wireless network
Base Station Name.....type in a short, simple name that you want to use to identify the AirPort Extreme
Password......type in a password that will be used for both the Base Station and Wireless Network
Verify the password
Click Next
You should have a green light on the AirPort Extreme in a minute or two, and you should be able to log on to the new network and get an Internet connection.

Trying to connect airport extreme to comcast provided ubee modem. Light on airport green, but no internet access.

Attempting to connect ubee d3.0 comcast modem to airport extreme base station.
Light on airport will go green, but I cannot connect to the internet.
I'm sure it has something to do with DHCP/NAT - as the airport extreme is getting an IP address, but then assiging a 10.x.x.x IP to my computer
but attempts at putting it in bridge mode just causes the light to go yellow and give warning of "No DNS Server" and "No internet connection"
I am able to connect to the internet when I connected directly to the modem.
I'm running OS 10.8.5
previously had DSL modem and connected after a few easy tweaks of the NAT settings before. am unsure what the issue is on this on... have used up my rather limited tech knowledge.
any thoughts?
Thank you!

Attempting to connect ubee d3.0 comcast modem to airport extreme base station.
Light on airport will go green, but I cannot connect to the internet.
Ubee provides both cable modems and gateway devices. What is the model number of yours?
I'm sure it has something to do with DHCP/NAT - as the airport extreme is getting an IP address, but then assiging a 10.x.x.x IP to my computer
By default, the AirPort Extreme would performing as a router with both NAT & DHCP enabled. Also, it would act as a DHCP server for the local network and provide out Private IP addresses in the range of 10.0.1.2 - 10.1.1.200. The WAN-side IP address of the Extreme should be a Public one and provided to you by your ISP via the Ubee modem. Did you perform a "factory default" reset on the Extreme before attempting to connect it to the modem?

Help setting up using my airport extreme to share my internet connection

I want to use my built-in airport extreme to share my internet connection with my PS3. I have a verizon aircard and have read on the internet that this can be done (but not necessarily with airport). I turned on internet sharing with airport and my ps3 reads my connection and obtains my ip address, but then it says could not connect to internet due to DNS server error.
Could someone run me down the process step-by-step so I can see what I'm doing wrong? Thanks for your help.
P.S. I have a iMac running on leopard if that matters.

ll959reds, Welcome to the discussion area!
Unfortunately the Internet Sharing provided by OS X does not provide nearly the configuration possibilities as even a very inexpensive wireless router.
Also if the firewall is enabled on the iMac, it applies equally to all ports including the AirPort (wireless) connection to the PS3. Therefore the firewall will block many of the requests from the PS3. To solve this issues, you would either need to disable the iMac's firewall or configure the iMac's firewall to allow connections via the AirPort side.
A much simpler solution is to use a wireless router instead of your iMac to provide the connection for the PS3.

Just purchased Airport Extreme ac and lost internet connection 3X. Reset to factory settings and worked for 2 days then lost connection and remedied by unplugging power supply. Anyone else having problems?

Just purchased Airport Extreme ac and lost internet connection 3X in less than one week. Fisrt time, reset to factory settings and fixed problem. Has occurred 2 additional times and connection re-established by unplugging AP extreme. Anyone else having these problems? Do I have a bad router? Thanks.

I definitely think this is a Mavericks issue. My iMac running Mavericks is the ONLY system in the house that drops the network randomly while all other systems never lose the network. No idea how to resolve this, but here is the workaround I'm posting:
I've had the 'network drop' issue with my Airport Extreme for the last 2 months. It reconnects when I pull the ethernet cable and plug it back in. I've tried downgrading the AE firmware, resetting to factory, etc. Nothing worked. I finally threw in the towel and created a script that monitors my network connectivity and restarts my interface if it senses it has dropped:
#!/bin/ksh
while true
do
yup=`ping -c1 -t2 www.google.com|grep from`
if [[ -n $yup ]]
     then echo "Internet is connected!"
else
        ifconfig en0 down; ifconfig en0 up
        echo "Down at `date +%m%d%Y%H%M%S`">>./dropped.out
fi
sleep 5
clear
done
I know its a workaround, but its saving me the headache of constantly pulling my cable and putting it back in!
Good luck!
-Mike Gray

How do I connect Airport Extreme in place of Buffalo wireless router in Japan?

How do I connect Airport Extreme to replace current Buffalo wireless router? ISP is StarCat in Japan.

Hello DM1960,
Thanks for using Apple Support Communities.
To set up and configure your AirPort Extreme please follow the steps in the article below:
OS X Mavericks: Set up an Apple wireless device
http://support.apple.com/kb/PH14058
Take care,
Alex H.

Connect Airport Extreme to existing router without ethernet cable

I am looking to connect my Airport Extreme to an existing router without the use of the ethernet cable. The existing router is on the ground floor whilst I would like to install the Airport Extreme in the first floor to improve WiFi range on the 1st floor. I am able to connect Airport Extreme to the router with the ethernet cable (in which case both the devices have to be close to one another on the ground floor) but unable to get Airport Extreme set up without the ethernet cable. Is it possible to connect Airport Extreme to the existing router on a non-wired basis (i.e. without the ethernet cable) and if yes, how would be I able to do it. Any help would be appreciated.

The AirPort Extreme can connect wirelessly.....IF.....your existing router is also another Apple router.
Is that the case here? If yes, what model number is your existing Apple router?
If no, you will need to continue to connect the AirPort Extreme using a wired Ethernet connection.

Connects to Airport extreme but not to internet

Whenever I close my laptop and reopen, I lose internet connection thru the airport extreme and I won't get it back. It seems that I will have connection to the Airport Extreme, but not the internet.
Sometimes what fixes it is turning the airport off and then on again (sometimes multiple times). Usually restarting the computer fixes it (but not always).
What happens is this (viewing Sysprefs/network/airport/network status and "internet connect"): the internet connect will report connecting...then will announce "connected", but show no "time elapsed" at the same time the Net status will read "airport is connected to ..network...with it's own IP address and may or may not be connected to the internet" And I won't be.
Then, when it starts working again (after the abovementioned turning off/on) it will start counting time elapsed, then in Net Status it will say "airport connected to ..network. you are connected to the internet via airport."
Also, whenever I use "internet connect" to turn the airport off, when I turn it back on again I will not have internet access, just the messages I list above. The "strenth meter" will say my signal is good (which it should be) and it says I am connected but doesn't show "elapsed time" nor will I have actual internet access.
Again, restarting the computer will usually work (less often, logging out then back in).
Another strange symptom-- When I hit the "disconnect" button under the airport section of "internet connect" it disconnects, then reconnects immediately. When I hit the disconnect button w/ in the Sysprefs/network/airport...etc, it does nothing but bring to the front window the "internet connect" window. So the only way to "disconnect" is to turn off the airport (which results in the above problem).
Side note--I am in the habit of turning off the airport (not the base, but from the computer) when I don't plan on using it for security-- am I being excessively paranoid? I do have my firewall in operation. Should I just leave it (being the airport) on all the time (in your humble opinion?
Sorry if this makes no sense or rambles, it is now 5:30 am and She Who Must Be Obeyed will be getting up in about an hour wanting to know if I fixed the computer yet. I'm tired.
Thank you in advance.
17" powerbook 1.5 PPc G4 Mac OS X (10.3.9)
17" powerbook 1.5 PPc G4 Mac OS X (10.3.9)

Try the following:
Delete Preferred Network(s)
- System Preferences > Network > AirPort > Configure
- In the "By default, join:" pull-down menu, select "Preferred networks"
- Delete the network(s) you regularly use from the list
Delete AirPort Keychain Entries
- Launch the "Keychain Access" application located in Applications/Utilties.
- Click on the "Kind" filter at the top, and look for any "AirPort network password" entries...and delete them.
- Restart, or log out then back in.
Add Preferred Network(s)
- System Preferences > Network > AirPort > Configure
- In the "By default, join:" pull-down menu, select "Preferred networks"
- Add the preferred network(s) using the "+" button.
- Restart or log out then back in.

AirPort Extreme splits or multiplies internet source?

Lets assume that my AirPort Extreme (n) was connected to a 2mbps effective DSL modem, and 4 devices were wired/wirelessly connected to my AirPort.
Would each device receive 512kbps of internet (i.e. the AirPort splits the internet source of 2 mbps four ways) OR would each device receive the full 2mbps (i.e. the AirPort supplies 2mbps to each device)? What I'm trying to get at here is whether the AirPort Extreme (n) acts as a Router or as a Switch in relation to the internet supply?
Thanks

Lets assume that my AirPort Extreme (n) was connected
to a 2mbps effective DSL modem, and 4 devices were
wired/wirelessly connected to my AirPort.
Would each device receive 512kbps of internet (i.e.
the AirPort splits the internet source of 2 mbps four
ways) OR would each device receive the full 2mbps
(i.e. the AirPort supplies 2mbps to each device)?
You can't get bandwidth out of thin air. The 2Mbps gets "split" among all connected devices. Not all of them get the same: one may get 128kbps, another one may be 512Kbps, another one may get 700Kbps, but the combined total will ever exceed 2 Mbps.
What I'm trying to get at here is whether the AirPort
Extreme (n) acts as a Router or as a Switch in
relation to the internet supply?
The AEBSn performs as a "router" with NAT and DHCP.

Connect AirPort Extreme Base Station to air card

How do you connect AirPort Extreme Base Station to Verizon Air Card?

Sorry, but the Air Card cannot be used with the USB port on the AirPort Extreme because that port will only work with a hard drive and/or a printer.
Suggest that you check with Verizon to see if they have an adapter or wireless router for the Air Card that will provide an Ethernet signal to the AirPort Extreme.

Can I use non-apple notebook to connect AirPort Extreme?

I
Can I use non-apple notebook to connect AirPort Extreme?

He might be trying to do so to promote his products or may be there was some misunderstanding.
Airport Extreme will work as a wireless router supporting upto 50 systems including Mac computers, PCs, iPad, iPhone, iPod touch, Apple TV and virtually all 802.11a/b/g/n Wi-Fi wireless devices — all at the same time.
for reference http://store.apple.com/us/product/MD031LL/A/AirPort-Extreme

Wifi connection AirPort Extreme with IP-camera

I can't establish wifi connection Airport Extreme with IP-camera. At the same time cable connection is fine, but wifi not.
Please, give me an advise.

You need to create a wireless network on the AirPort Extreme, and then you probably will want to assign a compatible static LAN IP address to the camera so that you can port-forward from the router to the camera.

Connecting Airport Extreme to a DSL

I have recently acquired an Airport Extreme which is connected to the DSL via an old Linksys Router. Signal keeps dropping and is slow especially in distant rooms. What is the best way to connect airport to DSL.
Does the Linksys wireless need to be disabled, if so please advise me how to do it.
Thank you.

If you add an AirPort Extreme to your existing Frontier Net network and permanently connect the AirPort Extreme to the Frontier wireless router using a wired Ethernet cable connection...
AND......you locate the AirPort Extreme in another part of your house where you need more wireless signal strength and coverage.......
AND......you configure the AirPort Extreme to create a wireless network that uses the exact same wireless network name and password as the Frontier wireless network.......
Then, you will have a much "bigger" wireless network with much greater range with higher wireless speeds throughout the house.
That would be be a good investment if your goal is to have a much bigger wireless network with greater range and speed throughout the house.

New Airport Extreme, Green Light, No Internet

Trying to get wifi connection so my mom can use her new ipad I bought her for Christmas and so guests can use wifi when they visit. I connected this new airport extreme 802.11n Wi_Fi to their comcast modem. After connecting get green light on airport extreme but now no internet connection on mac desktop computer. Have tried resetting modem, powering off airport and computer... still no internet. Internet works fine using comcast modem but does not connect to internet at all with airport extreme. Help. Extremely frustrated and ready to return this airport extreme.

Welcome to the discussion area!
It's likely not the AirPort Extreme that is causing your issue. It is the cable modem.
Perhaps you were not aware that a cable modem must be completely reset whenever there is a change in the device that the modem is connected to? Your ISP should have made this clear to you. A good reset often takes 30 minutes or more.
Push the reset button on the modem
Power off the modem for 30 minutes
Pull the battery if it's easily accessible
Power down the AirPort Extreme and your computers
After the wait period, power up the modem first and let it run for 3-4 minutes by itself.
Then power up the AirPort Extreme the same way
Then power up your other devices the same way
Please post back on your results.
Message was edited by: Bob Timmons
Message was edited by: Bob Timmons

How do I connect airport extreme to seagate hard drive using windows

How do I connect airport extreme to seagate hard drive using windows?

First the AirPort Extreme Base Station (AEBS) cannot share out an external HDD attached to its USB port unless it is formatted in either HFS+ or FAT16/32. It will not work if the HDD is formatted in either NTFS or ExFAT.
If the HDD is formatted properly, when you access the AEBS with the AirPort Utility, does the HDD show up properly on the Disks tab of the utility?
If it does, then you would access the HDD as any other network share, using the following format: //servername/sharename. In the case of the AirPort Disk (a HDD attached to the USB port of either an Extreme or Time Capsule), the "servername" would be the Extreme's Base Station Name, and the "sharename" would be the volumename of the HDD.

Connect AirPort Extreme to my FritzBox internet router

Similar Messages

Maybe you are looking for