Connect Aperture 3 with IOS devices

i like to view the edited pictures from aperture 3 on my IOS devices. Unfortunately i can only see the original RAW (NEF) and not the final picture.
Any idea what i did wrong in my workflow?

Settings>Mail>Hotmail account>Advanced>Delete from Server>When removed from inbox

Similar Messages

  • Why only 39 mbps with iOS devices?

    I have an Airport Extreme which runs firmware version 7.4.2. When I got an iPad several months ago, I noticed that the AirPort Utility reported a transfer rate of only 39 mbps to it. Even if the iPad was only a foot away from the router. Macs connect with rates of up to 130 mbps on the 2.4GHz band and 300 mbps on the 5 GHz band. If I switch the router to G-only mode, all the devices connect at 54 mbps.
    I have been unable to find out why this happens. Some other people on the iPad forums reported this too, but I could not find an answer.
    Yesterday I got an Apple TV and it connects at a 39 mbps rate too. So now I suspect that the problem is with the AirPort and not the iPad. It does not seem to work properly with iOS devices. Does anyone know what causes this and if there is a fix for it?

    I have a new Airport Extreme N that I got a few weeks ago and
    I just did a check with my Ipod 3rd gen w/iOS4.1 and it is connected
    at 54 Mbps, and my iMac which I am using at this moment
    is at 300 Mbps and when my MacMini is up, it connects at 300 Mbps.
    It seems that there may be an issue with your Airport or, there may be
    alot of interference in the B/G bands where you are at.
    Also note, that all my Airport settings are at default. I did not do
    anything special except change the IP address assignment numbers.

  • Edge Animation having troubles with iOS devices within Muse Site

    Hi All! I've been creating a mobile version of my website www.rinkdesigns.com and have it all complete. I created an animation/navigation bar within Adobe Edge Animate and imported it into Muse. It functions AMAZINGLY on my Nexus 4 (Android) in Chrome but on a buddies iPhone 5 Chrome only loads about 3/4 of the animation/nav bar, in Safari the animation does not load at all and half of the page background does not load either. Please check out the preview site here http://rinkdesignsmobile.businesscatalyst.com/phone
    Has anyone else been having animation/mobile troubles with iOS devices? Any hints as to how you fixed your errors would be extremely helpful! I also posted this question in the Muse forum and haven't gotten a response...
    Thanks,
    John

    Or, how about this:
    Does anyone know how to have Edge Animate objects that utilize "_top" in an open url trigger make the Muse site that they are a part of open a new window/tab with that action (as opposed to having it open the url in the current page, or using "_blank" in the trigger)?

  • HT204150 iCloud Contacts with iOS devices

    I've tried each step under "Troubleshooting iCloud Contacts update or setup issues with iOS devices" several times to no avail.  I can't get icloud to update Contacts on my iPhone 4.  Any suggestions will be greatly appreciated.

    Welcome to the Apple Community.
    First check that all your settings are correct, that contact syncing is checked on all devices (system preferences > iCloud on a mac and settings > iCloud on a iPhone, iPad or iPod).
    Make sure the contacts you are adding are added to your 'iCloud' group and not an 'On My Mac', 'On My Phone' or other non iCloud group (you can do this by checking in groups), non iCloud contacts will not sync.
    If you are sure that everything is set up correctly and your contacts are in the iCloud group, you might try unchecking contact syncing in the iCloud settings, restarting your device and then re-enabling contact syncing.

  • How use time capsule with IOs device ?

    Hi ..
    I have 2 time capsule and iphone and ipod touch
    and i saw this on apples website...
    how can I use the time capsule with IOs devices please ?
    thanks a lot.
    here is the picture

    Thanks for the clarification....(our crystal ball is broken).
    You might want to take a look at an App like FileBrowser.
    App Store - FileBrowser - Access files on remote computers
    The experts in the iPad support area will probably have more ideas for you as well if you want to post over there.
    Using iPad

  • Email settings DO NOT WORK WITH iOS Devices

    Vz keeps sending these "important" instructions for email port settings, BUT they do not work with iOS devices--iPhones and iPads. Last go around with this I spent over 16 hours trying to reconcile until an Apple Expert discovered "special" instructions for iOS device settings. Get with the program, Verizon.

    So what are the special instructions?

  • Internal server error while connecting SAP's customer financial fact sheet with iOS device

    Hi all,
    I am trying to connect SAP's customer financial fact sheet latest ( version 3.7)   with iOS phone/iPAD (version 7.1) but it shows internal server error,
    when trying to connect  Neither "Gateway (direct)" nor "SMP Cloud" enabled with port 80/443.
    On other hand my android devices with this app is working ok.
    Trace Log is below:
    2014-09-11 11:27:58.298 Debug Communication error: Error Domain=HTTPRequestErrorDomain Code=11 "INTERNAL SERVER ERROR" UserInfo=0x15eef620 {NSLocalizedDescription=INTERNAL SERVER ERROR}
    2014-09-11 11:27:58.295 Debug Request http://server:8010/url t finished with error Error Domain=HTTPRequestErrorDomain Code=11 "INTERNAL SERVER ERROR" UserInfo=0x15eef620 {NSLocalizedDescription=INTERNAL SERVER ERROR}
    response <?xml version="1.0" encoding="utf-8"?><error xmlns:xsi="http://www.w3.org/2001/XMLSchema-Instance"><code>HTTP/500/E/Internal Server Error</code><message> Call of service /sap/opu/odata/sap/fincustfactsheet terminated because of an error. The following error text was processed in system NQT : The ASSERT condition was violated.The error occurred on the application server . The termination type was: RABAX_STATE.If the termination type is RABAX_STATE, you will find more information on the cause of termination in system NQT in transaction ST22. If the termination type is ABORT_MESSAGE_STATE, you will find more information on the cause of termination on the application server  in transaction SM21. If the termination type is ERROR_MESSAGE_STATE, you can search for further information in the trace file for the work process in transaction ST11 on the application server . You may also need to analyze the trace files of other work processes. If you do not yet have a user ID, contact your system adminmistrator. </message></error>
    2014-09-11 11:27:58.286 Debug [ERROR] 500:INTERNAL SERVER ERROR/Location:-[ODPRequest startSynchronous] + 1427
    2014-09-11 11:27:56.239 Debug DE:Using SUP Manual User
    2014-09-11 11:27:56.238 Debug DE:Get svcDoc URL http://server:8010/url
    2014-09-11 11:27:56.216 Debug DE:startSAPODataRequest CompanyCodeCollection
    2014-09-11 11:27:56.204 Debug DE:SAPODataAccess dealloc CompanyCodeCollection
    2014-09-11 11:27:56.198 Debug DE:CustomerCardsViewController refresh
    2014-09-11 11:27:52.600 Debug Logging/Tracing on
    2014-09-11 11:27:19.792 Debug Communication error: Error Domain=HTTPRequestErrorDomain Code=11 "INTERNAL SERVER ERROR" UserInfo=0x193f3060 {NSLocalizedDescription=INTERNAL SERVER ERROR}
    2014-09-11 11:27:19.787 Debug Request http://server:8010/url  finished with error Error Domain=HTTPRequestErrorDomain Code=11 "INTERNAL SERVER ERROR" UserInfo=0x193f3060 {NSLocalizedDescription=INTERNAL SERVER ERROR}
    response <?xml version="1.0" encoding="utf-8"?><error xmlns:xsi="http://www.w3.org/2001/XMLSchema-Instance"><code>HTTP/500/E/Internal Server Error</code><message> Call of service /sap/opu/odata/sap/fincustfactsheet terminated because of an error. The following error text was processed in system NQT : The ASSERT condition was violated.The error occurred on the application server. The termination type was: RABAX_STATE.If the termination type is RABAX_STATE, you will find more information on the cause of termination in system NQT in transaction ST22. If the termination type is ABORT_MESSAGE_STATE, you will find more information on the cause of termination on the application server  in transaction SM21. If the termination type is ERROR_MESSAGE_STATE, you can search for further information in the trace file for the work process in transaction ST11 on the application server . You may also need to analyze the trace files of other work processes. If you do not yet have a user ID, contact your system adminmistrator. </message></error>
    2014-09-11 11:27:19.768 Debug [ERROR] 500:INTERNAL SERVER ERROR/Location:-[ODPRequest startSynchronous] + 1427
    2014-09-11 11:27:12.717 Debug timeout
    2014-09-11 11:27:12.681 Debug timeintervalinminutes: 23506917 timeoutInterval: 0
    2014-09-11 11:27:12.679 Debug applicationGoesToForeground
    Can anyone help me how to troubleshoot this error?
    Any help will be highly appreciated.
    Thanks
    Mahesh

    are these LUNs shared or standalone?
    I don't think it's really wise to have more than one DSM on the same server, so you're mixing the EVA and 3par DSMs and on 2003...
    other than ensuring that HBA firmware and drivers are all up to date and DMS drivers are at the latest, not much else you can do from the host side...maybe update the storport.sys driver to the latest for that OS
    are you sure that the HBAs are in fact supported/compatible with both storage back-ends? what about their driver/firmware/DSM versions - some SANs are very picky when it comes to this stuff, check the interop matrixes to find out
    overall, if you don't need SAN connection to one of these storage back-ends, I suggest you get rid of it and its DSM

  • Is wifi syncing with iOS devices encrypted?

    Anyone know whether the connection between your iOS device and iTunes is encrypted when you sync over Wifi? 
    It's fine if it's not at home, but needless to say I can't sync anywhere else if that's not encrypted.

    In the iPhone and iPad the image quality of the transferred photos is blurred and I am looking for an easy and quick method to use.
    How are you syncing? Are you using Photo stream (iPhoto and Aperture: Using Photo Stream) or iTunes Photo Sync ( http://support.apple.com/kb/HT4236?viewlocale=en_US&locale=en_US )?
    Both methods should give you good quality photos on your IOS devices - indeed I am seeing very good quality pictures in my Photo Stream and in the albums synced from iTunes.
    If I am looking in my iPod photo cache, I see that all images synced to the IOS devices are at least 2MB in size.
    The current setting for the Preview quality is global. You cannot set the Preview quality differently for different projects or libraries. What you could do however, would be to change the setting, recreate previews with different settings for selected images, then change the preview quality back.
    And you can prevent selected projects from generating previews alltogether: Use the menu below the cogwheel in the Library Inspector to disable previews for selected projects:
    Regards
    Léonie

  • Time Capsule works with MacBook Pro (Mavericks) but not with IOS devices?  recent problem starting March 1, 2015.

    I have a Time Capsule version 7.7.3 (model A1470) which has worked fine for almost 2 years with all devices, Apple and otherwise.  As of beginning of this month, March 2015 - no longer works with a new IPAD mini 3 and 6-month old iPhone 6 (both updated as of last night) BUT still works fine with MacBook Pro (Mavericks 10.9.5) and Epson printer XP-600. 
    On both IOS devices Airport Utility shows the Time Capsule and shows green light connection to internet, but never does the connection. The little status circle just keeps going round and never shows the Wifi rainbow symbol. both devices work fine on other Wifi's.  Airport Utility on iPhone actually connects enough to check on Airport base station's firmware 7.7.3 and says it is up to date!  but sadly stays on LTE.
    Have tried resetting, replugging etc...
    Also, tried checking on updates.  Nothing shows in Airport Utility. When I try to go to see past updates ~/Library/Application Support/Apple/AirPort/Firmware to see if updated, there is no Airport in the Apple folder?
    A mystery...

    Reset the TC to factory and redo the setup. see details below.
    Here is the typical list of things you should try.. and if this doesn't help post again.
    Factory reset universal
    Power off the TC.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the TC to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
    N.B. None of your files on the hard disk of the TC are deleted.. this simply clears out the router settings of the TC.
    Setup the TC again.
    ie Start from a factory reset. No files are lost on the hard disk doing this.
    Then redo the setup from the computer or perhaps it is better using iOS on the phone or ipad currently having issues.
    1. Use very short names.. NOT APPLE RECOMMENDED names. No spaces and pure alphanumerics.
    eg TCgen5 and TCwifi for basestation and wireless respectively.
    Even better if the issue is more wireless use TC24ghz and TC5ghz with fixed channels as this also seems to help stop the nonsense. But this can be tried in the second round. For iOS the fixed channels particularly for 2.4ghz has helped.
    2. Use all passwords that also comply but can be a bit longer. ie 8-20 characters mixed case and numbers.. no non-alphanumerics.
    3. Ensure the TC always takes the same IP address.. you will need to do this on the main router using dhcp reservation.. or a bit more complex setup using static IP in the TC. But this is important.. having IP drift all over the place makes for poor networking. If the TC is main router it will not be an issue. This is a problem for a TC in bridge mode.
    If this is of no help.. what modem do you have? What function other than modem does it have.. ie none or router??
    How is the TC connected into the network? What function does it have? Router or bridge for example.
    Post a few screenshots of the setup.

  • Wifi roaming with iOS devices

    I have a weird problem that I find hard to diagnose.
    We have 6 iOS based devices: 2x iPhone 3 (iOS 4.2.1), 2x iPhone 4 (iOS 5.1.1) and 2x iPad 3 (iOS 5.1.1). Our Apple Wifi network has 2 APs: 1 Time Capsule (TC) and 1 Airport Extreme (AE). Both AP are interconnected with Ethernet cabling, the AE is connected to the internet and also function as the NAT and DHCP host. Both TC and AE run firmware 7.6 and are set up with the same SSID, both on channel 11. They are located at opposite ends of our apartment to create maximum radio coverage in the apartment.
    All iOS devices roam from one AP to the other when moving around EXCEPT one of iPhone 4. This iPhone only connects to the TC and is also not visible in the airport utility (both the iPhone version as well as on the Mac) when asleep. All other devices remain visible in airport utility even while asleep.
    Any ideas which settings to check to on the iPhone 4 that doesn't roam? Does it have to do with the fact it loses the Wifi connection while asleep?

    Thank you for your response, however I tried "forget this network" and "reset network settings" before I started this thread and that didn't help. I find the restore option a little drastic measure before knowing what could cause certain behaviour.
    To make sure I repeated step forget this network again, while being very close to the AP it fails to connect (=AE). I noticed that on the first attempt to connect it reports "unable to join the network "<SSID>". On the second attempt it does connect. Then it suddenly hit me that the problem may be on the AP side: the first attempt it tries to connect to AE but fails, on the second attempt it connects to TC. This iPhone was recently replaced by Apple under warranty and I use MAC Access Control on the APs. Normally you enter the MAC address of a new device on one AP and the new device shows automatically up on the access list of the other AP. However in this case I updated the existing entry on only one AP (the TC) and after checking the other AP (the AE) it still had the MAC address of the previous device. I assumed that changes to MAC access control on one AP would also be propagated to the other AP. Once I also manually updated the entry on the AE, it started to roam as expected.
    One additional note: the iPhone 3 running iOS 4.2.1 do drop the wifi connection while asleep AND not being powered with the USB cable. As long as they have external power they maintain the wifi connection. The iPad 3 (using iOS 5.1.1) will maintain the connection in any condition. The 2 iPhone 4 are still showing different behaviour, one drops while the other maintains the wifi connection in sleep mode. This could be caused by a difference in apps running on the 2 iPhones. But I don't really care as it doesn't affect the user experience.

  • IPhoto sync with iOS Devices does not work

    I have an 2007 iMac with OS X 10.9.1, iTunes 11.1.3 and iPhoto 9.5.1.
    I have an iPad 2 with iOS 7.0.4 and iPhone 4 with iOS 7.0.4.
    Around the update to OS X 10.9 I have the problem that I can't sync my iPhoto pictures with my iOS devices anymore.
    Beforehand I had no problem. But I can't tell exactly when this problem pop up the first time. (iOS 7, OSX 10.9, iTunes or iPhoto update???)
    The problem is: I can sync all my content with my iOS devices per iTunes without any problemsbut not the fotos from the iPhoto library.
    If I go to the Foto sync page in iTunes I see all my iPhoto Albums, Events, ... I can select and desect all these items. But if I sync this items I see that in the used memory bar no pictures are shown, the foto count do not show any number and on the iOS device all pictures are removed.
    To fix this problem I have tried some options.
    I have disabled the foto sync in iTunes, close iTunes, close iPhoto, remove the iPod cache from the iPhoto library, recreated the iPhoto database, obened iPhot and iTunes again, connectd the iOS device and try to sync some albums from the iPhoto libray again. But no pictuers are synced.
    I have created a new iPhoto library and added some fotos to the new library, created some albums. Then I tried to sync the iOS device with this library. The first sync wored. :-). But then I disconnected the iOS device and later I connected it again and synced another time and all fotos are gone again.
    The only way I can sync my fotos is to switch to folder sync instead of iPhoto library sync. This work, but this is a very bad option!
    What can I do to fix this problem?

    Open the iPhoto Libraray with the Finder as shown in this screenshot
    and locate the folder titled iPod Photo Cache and move it to the Desktop. 
    Close iPhoto, lanuch and try again.
    OT

  • Bridge SRP with IOS device for routing.

    Hi,
    Can someone please detail how-to use the SRP (essentially bridged) for WAN connectivity and an IOS device. I plan to use an 881 ISR for routing, NAT, IPSec, GRE and PAT.
    I note Ethernet port 4 on the SRP -U model is a selectable LAN/WAN port? But I can't find any documentation on how-to use this for WAN?
    The reason for wanting to use the SRP for WAN is 4G LTE is the only available WAN option for us (using the Sierra Wireless 320U via USB interface).
    I could not find any 800 series ISRs that support a USB WAN with the Sierra Wireless 320U? Correct me if I am wrong.
    Regards,
    Trent.

    Hello Yannick B.
    Once you have enabled iTunes Match and then add music from a CD, it will automatically add those to iTunes Match for you or you can go to a drop down menu Store > Update iTunes Match to add the tracks. If you have iTunes Match enabled on your iPhone, you will see the changes rather quickly once uploaded. 
    If you want to delete music from iTunes Match, just delete the tracks and a prompt will ask if you want to delete from iCloud. That should answer those questions for you.
    iTunes Store: Subscribing to iTunes Match
    http://support.apple.com/kb/ht4914
    iTunes Store: How to delete songs from iCloud
    http://support.apple.com/kb/ht4915
    Regards,
    -Norm G.

  • Inability to connect iPhone 5 with ios 7.0.3 to hidden WPA2 network

    My iPhone 5, running ios 7.0.3, cannot find the hidden WPA2 network at my office.  Other iPhones are able to connect to the network, using the same credentials I was given.  Many of the discussion I have read suggest changing the network access from WPA2 to WEP, and from what I can tell that's not a good idea.  Being that this network is at my company, I am not able to change any settings on the router.  Could anyone please advise me on how to resolve this issue?  Thank you in advance.

    Hi cltbox,
    Thanks for visiting Apple Support Communities.
    If your iPhone does not connect to a Wi-Fi network, but other devices can, try these troubleshooting steps first:
    Be sure you're in range of your Wi-Fi router (access point).
    Tap Settings > Wi-Fi and turn Wi-Fi off and on. If your Wi-Fi setting is dimmed, follow these steps.
    Restart your iOS device.
    Update your device to the latest version of software.
    You can find the troubleshooting article with these steps here:
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/ts1398
    Cheers,
    Jeremy

  • FaceTime on Mac (Yosemite) does not connect when calling an IOS device

    Hi all,
    Since my upgrade with Yosemite, I seem to be having issues with FaceTime (video/audio) calling iOS Devices. iMessage works just fine with Yosemite. But when i attempt to call the other party via FaceTime, i could hear it ring but cannot connect. Anybody else who has the same issue and does anybody know how to fix it? It would seem to be a Yosemite issue, because when i tried using my iPad and iPhone to call via FaceTime, it works just fine using the same Apple Id i used for the Macbook Pro (Mid 2010). But when I use my Mac to call the iPhone.. It rings but it does not connect.. I hope they fix this with the next update..

    For the ones who are interested: the problem has been "solved".
    Solution: none. I found out that the iPhone 4 from my girlfriend caused the problem. The iPhone made it impossible to FaceTime to each other from iPhone <> MacBook Pro. I think it's because the discontinued iOS support for the iPhone 4.
    Since she has the iPhone 6 FaceTime now works wonderful without any problem.

  • Hi there i just update my ipad2 and iphone 4 ios6 and now the bluetooth cannot connect to any other ios device?what i have to do now?

    I just update my ipad2 and iphone4 to ios6 but now
    My two device  bluetooth cannot connect with any other
    Ios device.

    Are you running Leopard on your Mac, Laurie?
    If so, try instead updating to iTunes 10.6.3.25. (That supports earlier models of iPhones running iOS 6, even though it can't run the new iPhone 5s.)
    A .dmg installer for iTunes version 10.6.3.25 for Mac OS can be found at the following download page on the Apple website:
    iTunes 10.6.3

Maybe you are looking for