Connect CS 6248 FI to N5K-C5548UP

How do i connect UCS 6248 Fabric Interconnect to N5K-C5548UP? do i need to use FCoE or vPC as i will have multiple SAN connected (using FC) on FI.
Please suggest best possible solution where i have minimul cabling hedache & can optimise physicl ports on N5K.

Mahesh,
Have you read through the UCS Deployment Guide? I would suggest starting there. After you're familiar with the options we can discuss/recommend further.
http://www.cisco.com/en/US/docs/solutions/Enterprise/Borderless_Networks/Smart_Business_Architecture/February2012/SBA_Mid_DC_UnifiedComputingSystemDeploymentGuide-February2012.pdf
Regards,
Robert

Similar Messages

Connecting UCS 6248 FI to N5K-C5548UP

hi,
How do i connect UCS 6248 Fabric Interconnect to N5K-C5548UP? do i need to use FCoE or vPC as i will have multiple SAN connected (using FC) on FI.
Please suggest best possible solution where i have minimul cabling hedache & can optimise physicl ports on N5K.
Regards
Mahesh

Hi Mahesh,
vPC for FCoE uplink and / or unified uplinks is not supported at this time.
vPC only for pure ethernet uplinks still works the same way.
./Abhinav

Please tell me how to connect with FCoE UCS-mini and Nexus N5k (N5K-C5548UP-B-S32)

I have UCS 5108 Blade Server Chassis (with two B200 M3 Blade Servers inside and two FI 6324) connected to Nexus N5k switch through 4x10GE links.
I want to configure the two aggregated channels FCoE (vFC) from chassi to switch.
All instructions I've been seen refer to the fact that UCS-mini must be in the FC end-host mode, but UCSM 3.0 version does not support this mode, what shoud I do?
I set up following the instructions www.cisco.com/c/en/us/support/docs/switches/nexus-5000-series-switches/116248-configure-fcoe-00.html
But, after setup I have a fault on fabric: FCoE or FC uplink is down on Vsan 500;
And in Nexus: Vsan 500 is down (waiting for flogi)
When I do "show interface vfc 1" from Nexus CLI I see no 'Trunk vsans (up)', but
'Trunk vsans (initializing) (500)'
Unfortunately, I can't find technical notes for UCS mini (with UCSM v. 3.0), so may be You can promt any guides or suggestion for this?
Thank You in advance!

The release notes of 3.0.1e, which is for UCS-mini,
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/release/notes/ucs_3_0_rn.html
says:
Unsupported Features
The following features are not supported in Cisco UCS Manager, Release 3.0:
Features, defect fixes, and platforms introduced in Cisco UCS Manager, Release 2.2(2c) and newer that are not explicitly called out in New Features or Resolved Caveats sections of this document.
Some features introduced in Cisco UCS Manager, Release 2.2(1b) and earlier releases:
–Ethernet Switching Mode
–FC End Host Mode
– Private VLANs
– Port Security
– KVM Virtualization is not tested (although not explicitly disabled)

Nexus N5K-C5548UP UDLD troubles

I haven't been able bringing up links between N7k and and the new N5K (5548UP) due to errors with UDLD.
Someone else facing same problem ?
regards
Edmund
N5K:
Software
BIOS:      version 3.5.0
loader:    version N/A
kickstart: version 5.1(3)N2(1a)
system:    version 5.1(3)N2(1a)
N7K:
Software
BIOS:      version 3.22.0
kickstart: version 5.1(4)
system:    version 5.1(4)
Logs at N7K:
2012 Jun 15 14:46:58 swi-svi00A %ETHPORT-5-SPEED: Interface Ethernet1/2, operational speed changed to 10 Gbps
2012 Jun 15 14:46:58 swi-svi00A %ETHPORT-5-IF_DUPLEX: Interface Ethernet1/2, operational duplex mode changed to Full
2012 Jun 15 14:46:58 swi-svi00A %ETHPORT-5-IF_RX_FLOW_CONTROL: Interface Ethernet1/2, operational Receive Flow Control state cha
nged to off
2012 Jun 15 14:46:58 swi-svi00A %ETHPORT-5-IF_TX_FLOW_CONTROL: Interface Ethernet1/2, operational Transmit Flow Control state ch
anged to off
2012 Jun 15 14:46:58 swi-svi00A %ETHPORT-5-SPEED: Interface port-channel14, operational speed changed to 10 Gbps
2012 Jun 15 14:46:58 swi-svi00A %ETHPORT-5-IF_DUPLEX: Interface port-channel14, operational duplex mode changed to Full
2012 Jun 15 14:46:58 swi-svi00A %ETHPORT-5-IF_RX_FLOW_CONTROL: Interface port-channel14, operational Receive Flow Control state
changed to off
2012 Jun 15 14:46:58 swi-svi00A %ETHPORT-5-IF_TX_FLOW_CONTROL: Interface port-channel14, operational Transmit Flow Control state
changed to off
2012 Jun 15 14:47:05 swi-svi00A %UDLD-4-UDLD_PORT_DISABLED: UDLD disabled interface Ethernet1/2, empty echo detected
2012 Jun 15 14:47:16 swi-svi00A %ETH_PORT_CHANNEL-5-PORT_SUSPENDED: Ethernet1/2: Ethernet1/2 is suspended
2012 Jun 15 14:47:16 swi-svi00A %ETHPORT-5-IF_TRUNK_UP: Interface Ethernet1/2, vlan 1,60,100,358,370,380,500-501,505,700-703,710
-713,720-723,730-735,759-762,764-765,767,770,775-778,782-783,787-788,794-796 up
2012 Jun 15 14:47:16 swi-svi00A %ETHPORT-5-IF_TRUNK_UP: Interface Ethernet1/2, vlan 999-1000,1501,2029-2030 up
2012 Jun 15 14:47:16 swi-svi00A %ETHPORT-2-IF_DOWN_ERROR_DISABLED: Interface Ethernet1/2 is down (Error disabled. Reason:UDLD em
pty echo)
2012 Jun 15 14:52:16 swi-svi00A %ETHPORT-2-IF_DOWN_ERROR_DISABLED: Interface Ethernet1/2 is down (Error disabled. Reason:UDLD em
pty echo)
==
swi-svi00A# sh udld ethernet 1/2
Interface Ethernet1/2
Port enable administrative configuration setting: enabled-aggressive
Port enable operational state: enabled-aggressive
Current bidirectional state: unknown
Current operational state: disable-port - Multiple neighbor not detected
Message interval: 7
Timeout interval: 5
        Last pkt send on: 719482, Jun 15 14:47:05 2012
                Probe pkt send on: 401784, Jun 15 14:46:59 2012
                Echo pkt send on: 461880, Jun 15 14:47:05 2012
                Flush pkt send on: 719482, Jun 15 14:47:05 2012
        Last pkt recv on: 719134, Jun 15 14:47:05 2012
                Probe pkt recv on: 719134, Jun 15 14:47:05 2012
                Echo pkt recv on: None.
                Flush pkt recv on: None.
        Deep pkt inspections done: None.
        Mismatched if index found: None.
        Deep pkt inspection drops: None.
(Member of port-channel14)

You are probably running into bug-id CSCtz00790. (see below)
I had the same issue with UDLD no echo reply over SFP+ cables. The bug is Fixed-In 5.1(3)N2(1a)
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtz00790

Connecting N5K and Brocade CNA 1860

Tried 1, 3 and 7 m Cisco twinax cables, but Brocade is always reporting unsupported SFP. What should be used? Is there any twinax vendor that's is supported by both?
Thanks.

yeah, I found that link to and this part is disturbing:
"If you want to connect a Brocade CNA to a Cisco ToR switch (Nexus), you could use the EMC active twinax cable. Otherwise, you'll need to use optical since the Cisco switch will log an error if you attempt to use the Brocade cable."
But going optical is very expensive, we have over 20 servers and we would need 40 SFP+ for CNA and 40 SFP+ for Cisco...
I need someone who actually have up and running connection btw Brocade CNA and N5K to share what he used

Connect Nexus 5548UP-L3 to Catalyst 3750G-24T-E Layer 3 Switch

Please help!
Could anyone out there please assist me with basic configuration between Nexus Switch and Catalyst Switch, so that devices connected on the catalyst switch can talk to devices connected on nexus switch and vice-versa? In my current setup all servers on VLAN 40 are connected on the Catalyst Switch A as shown in the diagram below, and all desktops and all other peripherals are connected on the Catalyst Switch B. I am required to implement/add a new Nexus Switch 5548 that in the future will replace the Switch A. From now I just need to connect both switches together and start moving the server from Switch A to the Nexus Switch.
The current network setup is shown as per diagram below:
SWITCH A – this is a layer 3 switch. All servers are connected to this switch on the VLAN 40.
SWITCH B – all desktops, VoIP telephones, and printers are connected on tis switch. This switch is also a layer 3 switch.
I have connected together the Nexus 5548UP and SWITCH A (3750G) using the GLC-T= 1000BASE-T SFP transceiver module for Category 5 copper wire. The new network is shown as per diagram below:
Below is the configuration I have created in both Switches:
SWITCH A - 3750G
interface Vlan40
description ** Server VLAN **
ip address 10.144.40.2 255.255.255.128
ip helper-address 10.144.40.39
ip helper-address 10.144.40.40
interface Vlan122
description connection to N5K-C5548UP Switch mgmt0
ip address 172.16.0.1 255.255.255.128
no ip redirects
interface Port-channel1
description UpLink to N5K-C5548UP Switch e1/1-2
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,30,40,100,101,122
switchport mode trunk
interface GigabitEthernet1/0/3
description **Connected to server A**
switchport access vlan 40
no mdix auto
spanning-tree portfast
interface GigabitEthernet1/0/20
description connection to N5K-C5548UP Switch mgmt0
switchport access vlan 122
switchport mode access
spanning-tree portfast
interface GigabitEthernet1/0/23
description UpLink to N5K-C5548UP Switch e1/1
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,30,40,100,101,122
switchport mode trunk
channel-group 1 mode active
interface GigabitEthernet1/0/24
description UpLink to N5K-C5548UP Switch e1/2
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,30,40,100,101,122
switchport mode trunk
channel-group 1 mode active
N5K-C5548UP Switch
feature interface-vlan
feature lacp
feature dhcp
feature lldp
vrf context management
ip route 0.0.0.0/0 172.16.0.1
vlan 1
vlan 100
service dhcp
ip dhcp relay
interface Vlan1
no shutdown
interface Vlan40
description ** Server VLAN **
no shutdown
ip address 10.144.40.3/25
ip dhcp relay address 10.144.40.39
ip dhcp relay address 10.144.40.40
interface port-channel1
description ** Trunk Link to Switch A g1/0/23-24 **
switchport mode trunk
switchport trunk allowed vlan 1,30,40,100-101,122
speed 1000
interface Ethernet1/1
description ** Trunk Link to Switch A g1/0/23**
switchport mode trunk
switchport trunk allowed vlan 1,30,40,100-101,12
speed 1000
channel-group 1 mode active
interface Ethernet1/2
description ** Trunk Link to Switch A g1/0/24**
switchport mode trunk
switchport trunk allowed vlan 1,30,40,100-101,122
speed 1000
channel-group 1 mode active
interface Ethernet1/3
description **Connected to server B**
switchport access vlan 40
speed 1000
interface mgmt0
description connection to Switch A g2/0/20
no ip redirects
ip address 172.16.0.2/25
I get a successful response from Server A when I ping the N5K-C5548UP Switch (VLAN 40 interface (10.144.40.3) .But if I try to ping from Server A to Server B or vice-versa the ping fails. From N5K-C5548UP I can ping successful either Server A or Server B. What am I doing wrong here? Is there any additional configuration that I need to add on the Nexus Switch? Please Help. Thank you.

no, no secret aukhadiev
I made a mistake without realising and the interface e1/3 was showing "Interface Ethernet1/3 is down (Inactive)". After spending sometime trying to figure out what was wrong with that interface or switch, it turned out to be that i forgot to add the vlan 40. Now the config looks like this:
N5K-C5548UP Switch
feature interface-vlan
feature lacp
feature dhcp
feature lldp
vrf context management
ip route 0.0.0.0/0 172.16.0.1
vlan 1
vlan 40
vlan 100
service dhcp
ip dhcp relay
interface Vlan1
no shutdown
interface Vlan40
description ** Server VLAN **
no shutdown
ip address 10.144.40.3/25
ip dhcp relay address 10.144.40.39
ip dhcp relay address 10.144.40.40
interface port-channel1
description ** Trunk Link to Switch A g1/0/23-24 **
switchport mode trunk
switchport trunk allowed vlan 1,30,40,100-101,122
speed 1000
interface Ethernet1/1
description ** Trunk Link to Switch A g1/0/23**
switchport mode trunk
switchport trunk allowed vlan 1,30,40,100-101,12
speed 1000
channel-group 1 mode active
interface Ethernet1/2
description ** Trunk Link to Switch A g1/0/24**
switchport mode trunk
switchport trunk allowed vlan 1,30,40,100-101,122
speed 1000
channel-group 1 mode active
interface Ethernet1/3
description **Connected to server B**
switchport access vlan 40
speed 1000
interface mgmt0
description connection to Switch A g2/0/20
no ip redirects
ip address 172.16.0.2/25
Thank you,
JN

Storage direct connect

Hello,
Once we have the new 2.1(1) release for UCS Manager I'd like to know the following when using Fabric Interconnects in FC Switch Mode:
1) Is it possible to connect a supported storage array directly to the Fabric Interconnects at the same time of having a Nexus/MDS connected as an uplink switch?
2) Who will make the zoning in the latter case (MDS/Nexus or Fabric Interconnects)?
3) Is it possible to set up zoning between two storage arrays connected to the Fabric Interconnects so that is possible to replicate storage from one array to the other?
4) If storage array 1 is connected directly to the Fabric Interconnects while storage array 2 is connected to the Nexus/MDS uplink,is it still possible to zone and replicate between the two arrays?
Thanks,

Hi Dani,
Answers to your questions below.
1) Is it possible to connect a supported storage array directly to the Fabric Interconnects at the same time of having a Nexus/MDS connected as an uplink switch?
[ANSWER] Yes, you can connect a storage array directly to the FI, but make sure that you put it in a different VSAN than the one connected to MDS/N5K. You can enable zoning on this new VSAN and do the zoning in FI.
2) Who will make the zoning in the latter case (MDS/Nexus or Fabric Interconnects)?
[ANSWER] Your existing zoning will remain same and the zoning will have to be in MDS/N5K. This VSAN will not have zoning enabled in UCS.
3) Is it possible to set up zoning between two storage arrays connected to the Fabric Interconnects so that is possible to replicate storage from one array to the other?
[ANSWER] Replication is not possible through FI. If you have extra ports in new storage, you can connect those ports to MDS/N5K, and manage the replication through them.
4) If storage array 1 is connected directly to the Fabric Interconnects while storage array 2 is connected to the Nexus/MDS uplink,is it still possible to zone and replicate between the two arrays?
[ANSWER] No, you wouldn't be able to do this as they will be in different VSAN's. Again this can be managed as mentioned in point 3 above.

WAN Router Connection to Data Center

We have a WAN router that needs to connect to our Data Center network. The Data Center consists of two N7K core switches, with a pair of N5K switches as aggregation, and each N5K has twelve N2K fabric extenders. The N2Ks are single-homed to the N5Ks. The N5Ks are vPC connected to the N7Ks.
We would like to attach the WAN router to both N7K switches in the Data Center. The N7K switches only have 10G ports in them, so we can't terminate the WAN router directly to the N7Ks.
I was considering creating one dedicated VLAN on each N7K, and assigning an SVI to each VLAN, to correspond to the L3 connections between the N7Ks and the WAN router. Then, we could trunk these VLANs to each of the N5Ks, and configure one 1G port on each N5K for the VLAN, and connect the WAN router to the N5Ks.
Two questions regarding this design:
1) Is there a problem in connecting the L3 WAN router to the N7K via the N5K?
2) Does vPC connectivity between the N7K and N5K pose a problem for the proposed WAN connectivity?
Thanks in advance for any feedback.
-rb

The vPC between N5K and N7K is the catch here. Layer-3 routing over vPC member ports is currently not supported so I will advise you to stay away from this approach.
Atif

FI 6248 Nexus 5548 Port-channel problem

                   Hi all
I have a strange behavior between 2 FI and 2 nexus 5k configured as VPC , From a remote location and from my desktop I can ping odd ip and not even , from an other desktop in the same LAN the reverse, for both the tracert are good.
The only solution is to shutdown ports 1/1-2 on nexus A or FI A and in that case both desktops can ping both IP.
All seems OK, no log error , no error on interface , I give below some commands
What thing to know is that the nexus b has a L3 card , not the Nexus A , In fact I am waiting for a spare L3 daughter card.
On both NexusI have such configuration and status
interface port-channel201
description ucs-Fab-a
switchport mode trunk
switchport trunk native vlan 999
spanning-tree port type edge trunk
vpc 201
UCSM-PARIS-A(SSI153000ST)
                       Eth1/1        129    S I s     UCS-FI-6248UP Eth1/11
UCSM-PARIS-A(SSI153000ST)
                       Eth1/2        174    S I s     UCS-FI-6248UP Eth1/12
sh port-channel summary
201   Po201(SU)   Eth      LACP      Eth1/1(P)    Eth1/2(P)
sh mac address-table dynamic | i 1010
* 1010     0025.b5c9.481e    dynamic   0          F    F Po201
* 1010     0025.b5c9.481f    dynamic   10         F    F Po201
sh ip arp
10.203.136.21   00:01:05 0025.b5c9.481f Vlan1010
10.203.136.22   00:12:43 0025.b5c9.481e Vlan1010
On both FI A have such configuration and status
terface port-channel201
description U: Uplink
switchport mode trunk
pinning border
switchport trunk native vlan 999
switchport trunk allowed vlan 1,104,999,1010-1013,1020-1021,1500-1502,1510-151
2,1550-1552,1560-1561,1600-1602,1610-1619
speed 10000
sh port-channel summary
201   Po201(SU)   Eth      LACP      Eth1/9(P)    Eth1/10(P)   Eth1/11(P)
                                     Eth1/12(P)
sh mac address-table dynamic
* 1010     0025.b5c9.481e    dynamic   0          F    F Po201
* 1010     0025.b5c9.481f    dynamic   0          F    F Po201
sh cdp nei
E2RTR001(SSI1608085E) Eth1/9          120     S I s       N5K-C5548UP   Eth1/1
E2RTR001(SSI1608085E) Eth1/10         120     S I s       N5K-C5548UP   Eth1/2
E2RTR002(SSI16080F17) Eth1/11         151     R S I s     N5K-C5548UP   Eth1/1
E2RTR002(SSI16080F17) Eth1/12         136     R S I s     N5K-C5548UP   Eth1/2
Any ideas, A configuration I forgot on FI ?
Regards .

In fact in the probem I described the path is Esx -> FAB A - > N5K-A (for layer 2) -> N5K-B (for L3) -> routing to the LAN
And what you told me is that such configuration is not supported with VPC configuration , so I need to wait to receive the L3 card for the N5k-A. and check later if I have the same problem.
thanks

Cisco UCS - IOM to 6248 (FC)

Hi All,
Just a quick one - is anyone using FC to connect the 6248s to their IOMs ? I've reached the dreaded limit of the twinax cables.
I can see it's supported but just want to check the configuration changes needed as I'm in a full production environment.
Is it as simple as plugging in the SFPs and configuring a server port or do I need to change the UP to FC only which would require a re-boot of the 6248.
Cheers
Steve.

Steve,
We just need to configure the port type as " Server " and use the optical / FET SFPs to connect to Fibre channel link.
http://www.cisco.com/en/US/docs/unified_computing/ucs/hw/chassis/install/install.html#wp1275791
http://www.cisco.com/en/US/prod/collateral/ps10265/ps11544/data_sheet_c78-675245.html
HTH
Padma

Nexus 5500-UP licensing

I'm trying to build a config for a Nexus N5K-C5548UP-FA that will have a mix of FCoE and native fibre channel ports. What licensing do I need to purchase for the chassis to support this functionality? I'm not anticipating that any of the FC connections will be to other MDS appliances if that matters.
Specifically, when do I need these:
N55-8P-SSK9
N55-48PF-SSK9
N5548-FNPV-SSK9
thanks,
ds

Current FC FCOE licensing model on N5K is honour based.which comes in increment of 8.
(N5K-8P-SSK9) 8 port FC license .
However future model is going restrict on port based lcienses.
After installing N5K-8P-SSK9 license file which is called storage protocol service license.
you would see
"show license usage" output show as
ENTERPRISE_PKG Yes - Unused Never -
FC_FEATURES_PKG Yes - Unused Never
N55xx-FNPV-SSK9 is only for FCoE NPV mode, not for FC NPV mode. If you'd like to run FC NPV mode you need the Storage Services License, this license also includes the FCoE NPV license.
http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/san_switching/503_n2_1/Cisco_n5k_nxos_sanswitching_config_guide_rel503_n2_1_chapter6.html#topic_5492D4043C0746BFBE94FE6E2EBF7397

Nexus switch for storage

we are currently evaluating solutions for our storage upgrade.
we required 10GbE connection from storage to our servers.
there are 2 proposals that uses nexus switch.
1 uses nexus 5548 while the other one uses 3524.
i understand that 5548 is of a higher grade than the 3524.
i have 7 dell servers that will be connected to the switch using 10GbE NIC.
which nexus switch is more suitable for my environment.
7 servers -> 2 10GbE iSCSI switch -> 1x iSCSI storage(20TB)

Well...you're on a Cisco forum, so we'd be remiss in not recommending Cisco gear.
The Nexus 5548UP is around 17k for the base model without any special layer 3 licenses.
http://www.softchoice.com/catalog/en-us/hubs-switches-cisco-nexus-5548up-switch-managed-N5K-C5548UP-FA-HV7684
If you don't use layer 3 on the Nexus (which I wouldn't), they've got pretty good port density for the cost. NXOS takes little bit of getting used to and, for us, the copper SFPs have been a royal pain in the ass, but otherwise, they're pretty solid devices.

Nexus 5548UP L3 card swap out for L2 cards

Hi everyone,
I have two Nexus 5548UPs and I am going to swap out the L3 cards and put in L2 cards.
I can't seem to get a straight answer out of TAC so I thought I'd try here.
How will this affect the current configuration (apart of course from removing the L3 capability)?
Will swapping the cards clear the config?
Will swapping the cards clear the licenses?
It's a very simple config so that doesn't worry me that much .. but if it will clear the licenses installed than I need to take action on that.
Thanks,
BR

no, no secret aukhadiev
I made a mistake without realising and the interface e1/3 was showing "Interface Ethernet1/3 is down (Inactive)". After spending sometime trying to figure out what was wrong with that interface or switch, it turned out to be that i forgot to add the vlan 40. Now the config looks like this:
N5K-C5548UP Switch
feature interface-vlan
feature lacp
feature dhcp
feature lldp
vrf context management
ip route 0.0.0.0/0 172.16.0.1
vlan 1
vlan 40
vlan 100
service dhcp
ip dhcp relay
interface Vlan1
no shutdown
interface Vlan40
description ** Server VLAN **
no shutdown
ip address 10.144.40.3/25
ip dhcp relay address 10.144.40.39
ip dhcp relay address 10.144.40.40
interface port-channel1
description ** Trunk Link to Switch A g1/0/23-24 **
switchport mode trunk
switchport trunk allowed vlan 1,30,40,100-101,122
speed 1000
interface Ethernet1/1
description ** Trunk Link to Switch A g1/0/23**
switchport mode trunk
switchport trunk allowed vlan 1,30,40,100-101,12
speed 1000
channel-group 1 mode active
interface Ethernet1/2
description ** Trunk Link to Switch A g1/0/24**
switchport mode trunk
switchport trunk allowed vlan 1,30,40,100-101,122
speed 1000
channel-group 1 mode active
interface Ethernet1/3
description **Connected to server B**
switchport access vlan 40
speed 1000
interface mgmt0
description connection to Switch A g2/0/20
no ip redirects
ip address 172.16.0.2/25
Thank you,
JN

Nexus 5548UP and GLC-LH-SM showing sfpinvali

Hi gurus, have just received a 5548UP and when a 1GB GLC-LH-SM is inserted into the system it shows as being invalid.
Eth0/1       --                 sfpInvali 1         auto 10G     1/10g
4 different SFPs have been tried in numerous interfaces on the system. I have also upgraded the software to 5.0(2).
And I have tried setting the speed to 1GB on the interface.
Any ideas on what simple configuration task I have missed?
LP

Hi,
I've the same issue with GLC-T 1Gbps SFP tranceiver and NX-5548UP with L3 Daughter Card.
sh int e1/32 status
Port          Name               Status    Vlan      Duplex Speed   Type
Eth1/32       VLAN99             notconnec 99        full    1000    SFP-1000BAS
The cable is connected and in the other device (switch 2960x) the ethernet interface is UP
My configuration :
NX-OS : version 5.2(1)N1(4)
interface Ethernet1/32
description VLAN99
switchport access vlan 99
speed 1000
sh mod
Mod Ports Module-Type                       Model                  Status
1   32    O2 32X10GE/Modular Universal Plat N5K-C5548UP-SUP        active *
3   0     O2 Daughter Card with L3 ASIC     N55-D160L3-V2          ok
Tranceiver info :
Ethernet1/32
    transceiver is present
    type is SFP-1000BASE-T
    name is CISCO-METHODE
    part number is SP7041_Rev_E
    revision is E
    serial number is 00000MTC163405CF
    nominal bitrate is 1300 MBit/sec
    Link length supported for copper is 100 m
    cisco id is --
    cisco extended id number is 4
DOM is not supported
Interface capa :
Ethernet1/32
Model:                 N5K-C5548UP-SUP
Type (SFP capable):    10Gbase-(unknown)
Speed:                 1000,10000
Duplex:                full
Trunk encap. type:     802.1Q
Channel:               yes
Broadcast suppression: no
Flowcontrol:           rx-(off/on),tx-(off/on)
Rate mode:             none
QOS scheduling:        rx-(6q1t),tx-(1p6q0t)
CoS rewrite:           no
ToS rewrite:           no
SPAN:                  yes
UDLD:                  yes
Link Debounce:         yes
Link Debounce Time:    yes
MDIX:                  no
Pvlan Trunk capable:   yes
TDR capable:           no
FabricPath capable:    yes
Port mode:             Switched
FEX Fabric:            yes
Any idea ?
Regards,
Julien.

Partial collection Failure for nexus 5548UP in PI 2.1

Hi there,
I get "Partial Collection Failure" in the inventory collection status in Prime Infrastructure for all my Nexus 5548UP (8 devices).
i have seen in the PI 2.1 release notes that a bug CSCum16230 which look like my problem has been resolved in PI 2.1 but i continue getting the "partail collection failure"
Would like to know if the bug is still exist or get any other help to solve this problem.
Regards,
Alon.

hello
I have this problem as well...
we've got four N5K-C5548UP. Two with a layer 3 daughter card and two without.
interestingly we see the issue just on those boxes with the l3 daughter cards N55-D160L3-V2 installed...
Any help or ideas are highly appreciated
regards
roman
Sh inventory:
OK:
device-a# sh module
Mod Ports Module-Type Model Status
1 32 O2 32X10GE/Modular Universal Pla N5K-C5548UP-SUP active *
3 0 O2 Non L3 Daughter Card N55-DL2 ok
Mod Sw Hw World-Wide-Name(s) (WWN)
1 5.1(3)N2(1c) 1.0 --
3 5.1(3)N2(1c) 1.0 --
NOT OK:
device-b# sh modu
Mod Ports Module-Type Model Status
1 32 O2 32X10GE/Modular Universal Pla N5K-C5548UP-SUP active *
3 0 O2 Daughter Card with L3 ASIC N55-D160L3-V2 ok
Mod Sw Hw World-Wide-Name(s) (WWN)
1 5.1(3)N2(1c) 1.0 --
3 5.1(3)N2(1c) 1.0 --

Connect CS 6248 FI to N5K-C5548UP

Similar Messages

Maybe you are looking for