Connect EPM and web portal BPC through SAP router string

Dear Expert,
Please tell me how to connect EMP and web BPC through SAP router string?
thanks so much
hungth

Hi hungth,
Can you explain more? Do you mean you need a sap support to log on to your BPC web and investigate your BPC issues? If so, you can open HTTP connect connection by following note 592085.
Best regards,
Charlie

Similar Messages

Quality Server not connect through SAP Routing String

Hi,
When remotely access client SAP through SAP routing string in Quality Server it shows error message as
"timeout occured
Location : SAP router 37.11 on solman
Time: Tue May 05 11:19:37 2009
Component : NI (Network Interface)
Release : 640
Version : 37
Return Code : -93
Counter : 131 "
Here GUI version is 7.1(where from connecting). Client SAP version is ECC 5.0 and they use GUI 6.4 version. But Development server is being connected through SAP Routing String.
Regards,
Samrat

You might want to check following things:
Can you do a ping to the IP address you specified?
Is the data correct (ip, host, system number,...)?
Is the gateway with system number 00 running on the server?
Did you install the SAP RFC SDK dll's?
Glenn Colpaert - MCTS BizTalk Server - Blog : http://blog.codit.eu

Need to print SCC-14 and UCC-128 barcodes through SAP Smartforms

Hi all,
I have Two labels to be printed using smart forms.
But in one label the barcode should be of SCC-14 type
and in other the barcode should be of UCC-128 type.
<b>How to print SCC-14 and UCC-128 barcodes through SAP Smartforms?</b>
As standard barcodes do not meet my requirement i have created custom barcodes in transaction se73 of required height and width .
This is as:Se73>System Barcodes>change>Create>New-->:
I have given bar code and short text.
Narrow Module Width &Linear Height&Code128 Mode given default values.
But in this process where can i set the barcode should be of SCC-14.
> I have known that if we give Code128 Mode =
> 'U'-->It is like UCC-128.Is it correct ?
>
> But how can i know for SCC-14 barcode.
>And How many inches is euqal to 1 unit of Narrow Module Width &
How many inches is euqal 1 unit of Linear Height?
Please help me in this regard.It is urgent.
All solutions from you will be fully rewarded.
Thank you in advance.

Hi Rama,
We are working to print Bar codes using Smart forms.
Barcode is printing in label (4*6 Inchs) using printer (Zebra Z4 M PLUS (300 DPI)) (TLP-3842) which supports ZPL Language and Device type is ZLZEB3 (300 DPI).
We are printing bar codes successfully.
But After testing bar code using bar code tester (BC TESTER 4.4) software tool.
The results are failed.
We are expecting results: Like bellow.
Value formatted type is: EAN
Value is [C142007470
Total Description:   420. Ship To-Deliver to Postal Code a Single Postal Authority 07470
Current Situation:
Here we are Created Bar code (Ship to Post) in SE73 with
Bar code type is: Code 128
Width is: 08
Height: 300
Mode is: A    (Even I tried with N and U)
UCC check: Empty.
I added this to character format in my Smart forms.
Text in smart form is: ,,,,<C2>&W_POSTAL_CODE&</>    for P1 Paragraph.
Using this functionality we are able to print a Bar code in Label.
But while testing using BC Tester
Values are showing:
Value formatted type is: EAN
Value is 42007470
Total Description Values: Empty
The Type is EAN is when we select the Manually EAN Radio button (but this not capturing automatically this is problem we are facing).
Even I tried with some changes like bellow:
But Forcefully writing some code in Program lines Smartform:
               concatenate '420' fs_zediu017-pstlz into w_postal_code
After this forcefully adding this Value [C1 in Before W_postal_code Element text :
Text in smart form is:        ,,,,<C2>[C1&W_POSTAL_CODE&</>    for P1 Paragraph.
After this we are tested using BC tester
Every thing is displaying correct Vales which mention above when we manually select the Value formatted type radio button EAN but this Wrong.
Client need when testing bar code using BC TESTER 4.4 it should be display to take EAN radio button and showing all the Values.
Please let me know if you get any idea on this ?
Thanks,
Bathini.

How to use SAP Router String with SAP Web Services

Hi All,
I have developed an SAP Web Service and I'm using it from a vb.net dll by using web reference.
I want to use an SAP Router string when I try to call web service but I don't how to do it.Should the url of my proxy contain this router string in itself or is there any other attribute that I should configure for this purpose?
Please help!!!
MERAL
My code is as in the followings .
(And my SAP router string is like /H/111.11.111.11/H/)
Dim srvProxy As New PSUDamacanaProxy4.Z_SDB_RFC_GetList
            srvProxy.Url = s"http://21.11.1.43:8000/sap/bc/soap/rfc"
            srvProxy.Timeout = 10000
            srvProxy.Credentials = New System.Net.NetworkCredential(strUserName, strPassword)
            srvProxy.Z_SDB_RFC_GetList(p_bayi, durum, True, miktar, telefon, expMusteri, expReturnValue, expSiparis, expTeslimat, expAdSoyad)
            musteriAdSoyad = expAdSoyad
            ReturnValue = expReturnValue
            srvProxy.Dispose()
            srvProxy = Nothing

Since I posted this question, I have abandoned the notion of
auto-generated web services and embraced the good old FDS concept
where the RemoteObject meta-tag does all the conversion work for
me. We are now using the Granite DS package and it is working well
for us. I would love to consume web services, but it just isn't
worth the hassle when all you have to do with Granite (and FDS) is
cast your return objects to the proper object type.
BTW, since this posting, I have investigated competing Flex
app frameworks. After my research, I checked out the PureMVC
framework. Wow!! Cairngorm always left me with an uneasy feeling
and I guess I am not alone. Apparently, Cliff Hall felt the same
way. That is why he started the project. I like his approach alot
more than Cairngorm especially since it includes notifications
which allow me to broadcast my own app level events independent
from the AS Event framework. Check out PureMVC. For what it is
worth, it has my humble endorsement. Cliff was even gracious enough
to acknowledge the other Adobe Consulting guys for their work. Good
for you Cliff, I respect that. Check out a better way at
http://www.puremvc.org/

JCO Creation error using SAP router string

Hi All,
I have created technical system using customer system IP. After that I have created the JCO
I have given the details while creating a JCO:
JCO Name : <Name>
Client detail: <Client>
Message Server :< hostname>
Logon Group :<SPACE>
SAP Router String :< /H/<host IP>/H/S/<message server port number>
User Name :<User name>
Password :<***>
I have updated the Host and service file in the portal server.
When I am testing the JCO I got an exception:
com.sap.mw.jco.JCO$Exception: (102) RFC_ERROR_COMMUNICATION: Connect to message server host failed Connect_PM TYPE=B MSHOST=dicisap1 GROUP=PUBLIC R3NAME=DCD MSSERV=sapmsDCD SAPROUTER_STRING=/H/<RouterIP>/S/3600 PCS=1 LOCATION SAProuter 37.11 on SOLNMAN ERROR timeout occured TIME Wed Nov 05 17:42:31 2008 RELEASE 640 COMPONENT NI (network interface) VERSION 37 RC -93 COUNTER 4825
How to resolve this problem ?
Regards,
Boopathi M

Hi
Check out these thread
/message/5401584#5401584 [original link is broken]
JCO$Exception: (102) RFC_ERROR_COMMUNICATION: CPIC-CALL: 'SAP_CMACCPTP'
Thanks

What's SAP Router String for?

Hi,
I can not find proper module for me to post this message, so I post it here.
When we create a new item in the SAP logon screen , we need to specify the following parameters:
1) System description
2) Message server
3) SAP Router String (optional)
4) System ID
5) System Number
4) Group
My question is, what's SAP router string for? How to define a new SAP router string?
Because sometimes we don't need to input SAP router string, and we can still logon to the system successfully.
So, If I need to create a new SAP router string, where to define?
Thanks.

Hi
A route string describes the stations of a connection required between two hosts. A route string has the syntax
(/H/host/S/service/W/pass)*
It consists of any number of substrings in the form /H/host/S/service/W/pass .
A route string contains a substring for each SAProuter and for the target server.
Each substring contains the information required by SAProuter to set up a connection in the route: the host name, the port name, and the password, if one was given.
Syntax for substrings:
·        /H / indicates the host name‑{}‑
Note that the host name must be at least two characters long.
·        /S/ is used for specifying the service (port); it is an optional entry, the default value is 3299
·        /W/ indicates the password for the connection between the predecessor and successor on the route and is also optional (default is u201Cu201D, no password)
In earlier Releases (<4.0A), the password entry was made one substring later and with the letter /P/.
New: /H/saprouter/W/pass/H/targetserver
Old: /H/saprouter/H/targetserver/P/pass
(Here pass is the password which is checked by the SAProuter on host saprouter to set up or prohibit the connection from the source host to the target host.)
Due to downward compatibility, the old password entry form is still possible.
Thenaks & Regards
Kishore

Enterprise Application and Web Portal Projects

I know its possible to have one enterprise application that contains 2 web portal projects. The part Im unsure about is if it is possible to update one web project without having to bring down the other project. Supposedly through console you can do this however I have been unable to get this to successfully work. Is this a known error?

Hi Anikumar!
Yes it is true! The webDynpro make it automaticaly.
I'm not clear with J2EE web application. I don't know how i should get the login parameter for my RFC calls.
I have try:
DestinationService dstserv =(DestinationService) ctx.lookup(DestinationService.JNDI_KEY);
RFCDestination dest =(RFCDestination) dstserv.getDestination("RFC", "test");
Properties destprop = dest.getDestinationProperties();
String user1="MYSAPSSO2";
String passwd1=pass;// pass is encrypted ticket;
destprop.setProperty("jco.client.user",user1);
destprop.setProperty("jco.client.passwd",passwd1);
JCO.Client cl = JCO.createClient(destprop);
cl.connect();
cl.ping();
cl.disconnect();
I also try
IWDJCOClientConnection ca = WDSystemLandscape.getJCOClientConnection("ModelData");
In the contentadministrator Modeldata Destination set to Ticket authentification and it works fine when i test it in webdynpro contentadministrator, but when i try to get the JCOConnection i get a SystemLandscapeException:Error while obtaining JCO connection.
I debugged it and i get a WDRuntimeException--->Nullpointerexception. It seems that the jco destination is not initialized at this time.
Maybe i understand something wrong.
Regards!

To upload a RTF and a PDF file to SAP R/3 and print the same through SAP

Hi,
I have a requirement to upload a PDF file and a RTF file to SAP R/3 and print the same.
I wrote the following code for uploading a RTF file to SAP R/3 and print the same. However, the problem is , the formatting present in the RTF document( bold/italics..etc) is not being reflected when I do the 'print-preview' after the executing the code below :
report z_test_upload .
data: begin of itab occurs 0,
         rec type string,
      end of itab.
data: options like itcpo.
data: filename type string,
      count type i.
data: filetype(10) type c value 'ASC'.
DATA: HEADER LIKE THEAD    OCCURS   0 WITH HEADER LINE.
DATA: NEWHEADER LIKE THEAD    OCCURS   0 WITH HEADER LINE.
DATA: ITFLINE LIKE TLINE    OCCURS   0 WITH HEADER LINE.
DATA: RTFLINE LIKE HELP_STFA OCCURS   0 WITH HEADER LINE.
DATA:   string_len TYPE i,
        n1 TYPE i.
selection-screen begin of block b1.
parameter: p_file1(128) default 'C:\test_itf.rtf'.
selection-screen end of block b1.
AT SELECTION-SCREEN ON VALUE-REQUEST FOR p_file1.
CALL FUNCTION 'F4_FILENAME'
       IMPORTING
            file_name = p_file1.
start-of-selection.
move p_file1 to filename.
call function 'GUI_UPLOAD'
     EXPORTING
          filename                = filename
          filetype                = filetype
     TABLES
          data_tab                = itab
     EXCEPTIONS
          file_open_error         = 1
          file_read_error         = 2
          no_batch                = 3
          gui_refuse_filetransfer = 4
          invalid_type            = 5
          no_authority            = 6
          unknown_error           = 7
          bad_data_format         = 8
          header_not_allowed      = 9
          separator_not_allowed   = 10
          header_too_long         = 11
          unknown_dp_error        = 12
          access_denied           = 13
          dp_out_of_memory        = 14
          disk_full               = 15
          dp_timeout              = 16
          others                  = 17.
if sy-subrc <> 0.
message id sy-msgid type sy-msgty number sy-msgno
            with sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
endif.
loop at itab.
string_len = strlen( itab-rec ).
n1 = string_len DIV 134.
ADD 1 TO n1.
DO n1 TIMES.
    rtfline-line = itab-rec.
    APPEND rtfline.
    SHIFT itab-rec BY 134 PLACES.
ENDDO.
endloop.
HEADER-TDSTYLE = 'S_DOCUS1'.
HEADER-TDFORM = 'S_DOCU_SHOW'.
header-tdspras = 'E'.
CALL FUNCTION 'CONVERT_TEXT'
EXPORTING
CODEPAGE               = '0000'
    DIRECTION              = 'IMPORT'
    FORMAT_TYPE            = 'RTF'
   FORMATWIDTH            = 72
    HEADER                 = header
    SSHEET                 = 'WINHELP.DOT'
    WITH_TAB               = 'X'
    WORD_LANGU             = SY-LANGU
    TABLETYPE              = 'ASC'
TAB_SUBSTITUTE         = 'X09 '
LF_SUBSTITUTE          = ' '
REPLACE_SYMBOLS        = 'X'
REPLACE_SAPCHARS       = 'X'
MASK_BRACKETS          = 'X'
IMPORTING
    NEWHEADER              = NEWHEADER
WITH_TAB_E             =
FORMATWIDTH_E          =
TABLES
    FOREIGN                = RTFLINE
    ITF_LINES              = ITFLINE.
LINKS_TO_CONVERT       =
if sy-subrc <> 0.
endif.
CALL FUNCTION 'PRINT_TEXT_ITF'
EXPORTING
     HEADER        = newheader
     OPTIONS       = options
IMPORTING
RESULT        =
TABLES
    LINES         = itfline.
if sy-subrc <> 0.
endif.
Any hints or suggestions to solve this problem will be highly appreciated.
Thanks,
Avra

Hi Vishwas,
Check out the thread [Efficient way of saving documents uploaded|Re: Efficient way of saving documents uploaded by users; and check the blog by Raja Thangamani.
Also check the thread [Export Images through Function Modules   |Export Images through Function Modules;.
Hope it helps you.

What ports to open between Connection broker and Web access hosts

I have setup a 4 node 2008 R2 RDS farm (1 connection broker, 1 Web access, and 2 session hosts.) They were all built from the same image, but the web access and connection broker will not talk to each other. They are all on the same subnet, and ips are x.x.x.200-203 The Web access server can ping the Sesions hosts, the session hosts can ping each other, web access and the connection broker. But the Web access and Connection broker cant ping each other. I turned off the windows firewall and they can ping, and connect... So whats ports does it need open?
Thanks!
~M

Hello,
Do you need any further helps? Please let us know it. Thanks.
· Lionel Chen
TechNet Subscriber Support in forum
If you have any feedback on our support, please [email protected]
This posting is provided "AS IS" with no warranties, and confers no rights.

How to disable web service authentication by sap-user string in url

Hi Experts,
I am publish some RFC function as webservice for my SAP AS ABAP, i set the authentication as basic. I can using http basic authentication to call the service and get the result. But it also accept passing user/password through the url string: http://localhost:8001/sap/bc/soap/wsdl11?services=BAPI_PO_CHANGE&sap-client=100&sap-user=myId&sap-password=myPassword
I want to disable this, make it no user/password through url string. Can anyone tell me how to do it, thanks.
Best regards,
Peter

Well, it's not a backdoor - but (extremely) bad style: an URL should never contain any authentication data (like UID & PWD) nor should it ever contain any (security) session ID (which, if valid, would allow to skip authentication).
So, I agree with you / your customer: it should be (made) possible to configure the system to discard / ignore any authentication data which is contained in the URL.
I recommend to submit a customer message to SAP (using message component BC-MID-ICF). You might refer to this SDN posting (by providing the URL) in the support ticket.
PS: Basic Authentication is not much better but at least the information (UID & PWD) is not sent in the clear (although simply Base64-encoded) and not in the URL (but in the http header). Sending cleartext data in the URL is really the worst. The best is: use stronger authentication mechanisms (e.g. X.509 client certificates, Kerberos, Biometric authentication mechanisms, etc.).

Can I use an hp b209 and an hp4500 wirelessly through a router on the same network

I have two HP printers that I would like to use wirelessly through a router. When I have tried to set both of them up, one or the other is not recognized. I have tried uninstalling and re-installing, and nothing seems to work.
This question was solved.
View Solution.

OK, good. Uninstall all HP software from Start > All Programs > Hewlett-Packard. Then restart your PC.
Now, get the latest software for the 4500 from the "Support & Drivers" link at the top of this page and install it. Restart your PC.
Finally, from the same link on this page get the latest software for the b209 and install it.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

How to fill the SAP router String :

Dear friends ,
During GUI installation 1 field is SAProuter String so what i fill here .
Please guide us for SAProuter String .
i) what is SAProuter String .
ii)What is use of SAProuter String.
Thanks & Regard
SAURAV KUMAR

Dear sourav,
Hope you got answer of your question if not following is the answer.
i think you need to know about the router string first.
router string is nothing but the external IP of the saprouter system which is mapped with the local IP of the saprouter system.
if you know router string you can put it directly, no need to add any thing extra. suppose your router string is 12.35.56.952 you can put it directly over their if you want to access remote SAP system if you are in LAN you don't need to put that.
hope this will solve you problem.
Regards
Rupesh Kr singh

Connecting client and web services with aqualogic

Hello, im engineer in training period at Unilog (Lyon,France) and im tesing aqualogic for evaluation
im nearly beginner in .NET and ESB and completely beginner in aqualogic, i have 1 problem :
i want to test communication between my .NET client and webservice, through Aqualogic.
i made some configuration but i wonder if its the right solution:
i created a proxy service with a pipeline pair node and a route node directed to registered business service.
But i dont know exactly how to connect my .NET client with aqualogic proxy service.
My client code is :
private void btnConnect_Click(object sender, System.EventArgs e)
Annu.Service1 oAnnu = new Annu.Service1();
oAnnu.Url = "http://localhost/WebService1/Service1.asmx";
string t = oAnnu.Tel("Dupont");
TextBox1.Text = t;
(this client code works without aqualogic, Annu is my Web reference to my web service)
Many thx again, cordially,
Pascal Camellini.
Message was edited by:
camellini

At the time of creating proxy service you should have filled endpoint url which is different from business service. Place the end point url of the proxy service in the client code url what you have written.
Follow the above step it will work properly

HT204387 I just updated my Iphone 4S to the new IOS. I have a sync sytem in my car that allows me to connect music and cell phone call through the vehicle. Since the update my phone is no longer finding the sync sytem to connect to.

I just updated my iphone 4s to the new ios update. My car is a sync system that connects through bluetooth. I go to my bluetooth setting to search for devices and it wont find any. I believed it to be that my car that was the problem; but my sister has the same update on her iphone and was able to connect to my car no problem. please help!!!

Hello 6underwood,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
iOS: Troubleshooting car stereo connections
http://support.apple.com/kb/TS3581
If you are experiencing difficulties with the connection between your stereo and device, disconnect the device, and then power cycle the stereo and your iPhone, iPod touch, or iPad. When the Home screen reappears, reconnect your device. If you cannot power cycle the stereo, turn the car off and then back on to allow the stereo to power off.
Best of luck,
Mario

RDS 2012 Connection Broker and Web Access in different domains

Hello!
I'm trying to add Web Access (WA) server to RDS 2012 Deployment. WA server and other servers in Deployment are in different domains (in different forests with 2-way forest trust).
WA server was added to Deployment
successfully without any warnings.
We have many applications published but in this new WA server there are no application icons in Rdweb page at all.
There is nothing interesting in logs on WA server as well as on Connection broker servers.
Is this design
acceptable? Which additional actions are needed to make application icons visible?

Hi,
Please refer below links and cross verify the Web Acess server settings.
http://blog.kristinlgriffin.com/2010/03/rd-web-access-is-emply.html
http://social.technet.microsoft.com/wiki/contents/articles/5974.the-case-of-invisible-remoteapp-programs-a-k-a-no-remoteapp-programs-listed-on-rd-web-access-site.aspx
Regards,
Manjunath Sullad

Connect EPM and web portal BPC through SAP router string

Similar Messages

Maybe you are looking for