Connect HP laserjet 2100TN to Imac 10.8 via ethernet cable

I want to connect my old HPlaserjet 2100tn to my new imac os 10.8 computer. Apple and HP say it is compatible. The printer was hooked to my G5 via the ethernet cable and worked fine. There is no usb hookup for this printer that I can find.
I am able to find an IP address for the printer via network, the print/scan finds the printer and adds it, driver is in place (after some searching from apple) and everything looks good. Only problem is it does not print. Get error message saying the printer doesn't exist and some other similar messages.
Have spent way too much time talking with apple and HP andit apears I know more about this than them anyway. It's too big a challenge I think.
Do I need to run through my router (old airport base staion that works just fine...looks like a spaceship) which has a port for another ethernet cable? My internet is wireless, this printer in not wireless capable (IR though..old), but can I hook it in and operate that way without srewing up my wireless internet?
Come on...someone has the simple answer to this question. Just want to use my old postscript laser printer every now and then.
Thanks for your help.

This may not help at all, but I have an HP Color LaserJet 2605dn, and one day it just stop being part of my network, as far as I could tell. Would not print, could not be found on the network, even after manually putting in network information.
I reset the printer. I did a NVRAM initializer and a Super NVRAM initializer. I found out how from the service manual for the printer.
I the setup the printer again, like I had taken it out of the box new.
Runs fine. Prints, is found on the network, can use the web based software it has in it.
Maybe this may work for you.
Good Luck.
G.

Similar Messages

Can I connect my Linksys WRT160N V3 with Airport Extreme via ethernet cable?

I have a Linksys WRT160N V3 router (Living Room) to my cable modem but the wifi does not reach certain spots in the house where its necessary. If I buy a Airport Extreme and place it in my bedroom and connect it with an ethernet cable that I have connected with my iMac will the airport extreme work as a wifi extender since wifi does not reach my room?

Yes, the AE can be simply put in bridge mode so it will become an AP and set the wireless to create a wireless network.. you can then use same name and same security as linksys.. this is called roaming network.
http://support.apple.com/kb/ht4260
Although the apple instructions have two apple routers, any two wireless routers will work the same way.

Connecting iMac to Network via Ethernet Cable and Airport Express

I've tried reading through the various posts to solve this and haven't had any luck. Any help is deeply appreciated.
I have an Airport Extreme as my main 'base' for our wireless network. I purchased an Airport Express today with the notion of using it to extend my network in the following way: I want to connect an iMac and a printer to the Express (using Ethernet and USB cables respectively) and have the Express serve as a remote for the Extreme base. I have found a number of websites saying this is possible, but none explain how to. I tried the WDS option, which failed to work. I later saw posts here saying that was not the optimal scenario. I'm afraid the 5Ghz/2.4Ghz settings combined with Airport ID addresses has pushed me past my competency!
Thanks in advance for your help and a festive St. Patrick's Day!

Temporarily, power down the AirPort Express and concentrate on the AirPort Extreme to make sure that it is functioning correctly, can get an Internet connection, etc.
A complete power cycle of the network is often useful when you have been making changes. Power everything off, order is not important.
Wait a moment, (or wait 5-10 minutes if you have cable modem), then power up the modem first and let it run a moment by itself. Then power up the AirPort Extreme the same way.
Check your settings using AirPort Utility - Manual Setup
Click the Wireless tab just below the row of icons
If the Wireless Mode setting is "Create a wireless network", make sure there is a check mark next to "Allow this network to be extended"
Note the exact setting for Security that is being used
Update to save any changes
Post back when the AirPort Extreme is functioning correctly as above and we'll tackle the AirPort Express

Connecting aiport extreme and airport express via ethernet cable ?

Is it possible to connect an airport extreme to an airport express via ethernet cable, I ask because I want to expand the range of my wifi network to the basement of my house, the floors are really thick concrete so I installed some ethernet cable runs, I hope somebody can help me, thank you.

+How do I do it ? Do I connect the modem to the airport extreme and then run the ethernet cable from one of the extreme's ethernet ports to the express ethernet on the basememt and a second cable from another of the extreme's ethernet connectors to the express on the second floor+
Yes, this is exactly correct.
To configure each AirPort Express (AX)
Open AirPort Utility, click Manual Setup
Click the Base Station tab below the icons to name your device, assign a device password and adjust time zone settings. Give each Express a separate name so you can identify then easily.
Click the Wireless tab
Wireless Mode...Create a Wireless Network
Wireless Network Name...Exact same name as your AirPort Extreme network
Radio Mode 802.11n (802.11b/g compatible) if you want to use 2.4 GHz
Channel...Automatic
Wireless Security...Exact same setting as your AirPort Extreme network
Wireless Password....Exact same setting as your AirPort Extreme network
Click the Internet icon
Change the Connection Sharing setting at the bottom to "Off (Bridge Mode)"
Click Update at the lower right and the AirPort Express will restart in 20-30 seconds
I think it is easier to configure each AirPort Express with AirPort Utility by temporarily connecting it to your computer with a short ethernet cable. Once you have saved the configuration, you can move the Express to the location that you need.
Please post back on your progress.

I have an HP LaserJet 8150N that I am trying to get connected via ethernet cable directly to my iMac. I always had this printer connected via a network so I don't know if I am able to connect directly with a cable since it is a network printer.

I have an HP LaserJet 8150N that I use for my work and I have had this printer for ever and it is one heck of a work horse! I am trying to get it connected via ethernet cable directly to my iMac. I always had this printer connected via a network so I don't know if I am able to connect directly with a cable since it is a network printer. I have tried to reconfigure the printer using the JetDirect menu giving it a new IP address but still no luck. If anyone could help me through this issue I would appreciate it.

moonlightcaravan wrote:
Second, seeing "connecting" and connection failed is normal. You must click on "Connect As" in the Finder window and then enter the username and password for the admin account on the other computer. That should fix things.
Thanks for responding.
When does clicking on "Connect As" happen in the process above?
After step six? Seven?
After the connection has failed?
Is this the FInder window that shows the icon of the computer you want to copy the file from?
You should see "Connect As" in the Finder near the top right of the window as shown below:
!http://blog.brothersoft.com/wp-content/uploads/2008/11/howto_copy_files_to_or_from_your_iphone02.jpg!

Macbook Pro suddenly will not connect to the internet via ethernet cable.

I know this is a long shot... but I figured I would give it a try.
My macbook pro suddenly does not connect to the internet via ethernet cable. Please bear with me, as I am not very tech-savvy - I will try my best to describe the symptoms!
I connect to the internet via ethernet (we don't have wifi). It was working before I went to work, and when I came home I suddenly couldn't get anything to work (I know everyone says this, but I truly didn't mess with anything). Internet browsers just think for awhile and then turn up the 'You are not connected to the internet' error.
I went into my network preferences and curiously, the 'Ethernet' shows a green dot and says 'connected'. However it says 'Authentication server is not responding' underneath the last part that says '802.1X: WPA: eduroam' (I think that is my user profile).
When I go into my 'security' settings I can see that my firewall is off, so that shouldn't be causing any problems.
I've tried restarting the router and computer itself many times. Diagnostics just gets to a certain point and reports back 'Network Diagnostics cannot fix the current networking problems.' I've also tried switching to a different ethernet cable, and I tried both cables out on a PC laptop and it connected without issue. Additionally, I brought my macbook along to a friend's house and it connected to his wifi just fine, so the problem appears to just be with ethernet connections.
I know it's hard to troubleshoot this kind of thing without being there and having a look at the computer yourself, but any tips wouild be greatly appreciated.

As I mentioned above, I am not very tech savvy so I have no idea why a wireless protocol would be showing up there, I'm just listing everything I see in hopes that someone might know something I can try. This is why I am asking for help here - I'm not sure what has happened that has made me unable to connect, especially since it seemingly occured while nobody was using the computer.
I guess I should clarify that I'm not a total hillbilly- normally my firewall is set to 'on', but I set it to 'off' to try and troubleshoot the issues here as I was told that sometimes it can interfere with the computer's ability to connect to the internet. If this is not the case and firewall does not affect anything, I will turn it back on while I try to fix this.
I have tried the method you mentioned above a few times - I actually contacted my ISP earlier this week and they recommended resetting the router like that. They didn't mention any known network issues.

I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. My question is I now wish to add a second Airport extreme but am considering a hard wire connecti

I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme. Can my network operate properly to extend the network with both a wireless and wired extend functionallity?

I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme.
Excellent plan.
Can my network operate properly to extend the network with both a wireless and wired extend functionallity?
Yes, but don't get confused about the second AirPort Extreme, as it would not be configured to "extend" a wireless network.....it would be configured to "create a wireless network" using the same wireless network name, security settings and password as the Time Capsule network. Configure the second Extreme in Bridge Mode.
This Apple support document will show you how to hookup and configure the second AirPort Extreme:
http://support.apple.com/kb/HT4260

HT2497 I just purchased the 2TB TC and set it up on bridge mode to my att verse which is connected via ethernet cable. The TC is continually blinking amber and an error message states that a wireless network cannot be found but the uverse is functioning

I just purchased the 2TB TC and set it up on bridge mode to my att verse which is connected via ethernet cable. The TC is continually blinking amber and an error message states that a wireless network cannot be found but the uverse is functioning great. The network name I assigned to the TC is also not appearing among available networks. How do I remedy this, please?

What OS on the computer you are using to setup the TC?
Did you turn on ipv6 for wireless to link-local... this is essential for network access now??
Try power cycling the network.. start up in correct order.. uverse.. 2min wait.. TC.. 2min wait.. computer.
No luck factory reset and start over. Use ethernet cable as well to the computer to help it.
No luck I can show you manual method.

I have a 3rd party hard drive with movies on it ,it is connected to my airport extreme. The AE is connected to my tv via ethernet cable. Can I stream my movies to the Tv ?

I have a 3rd party hard drive with movies on it ,it is connected to my airport extreme. The AE is connected to my tv via ethernet cable. Can I stream my movies to the Tv ?

Not without a player..
The AE is a dumb file server.. the hard disk you plug in is an even dumber hard disk.
There are no smarts in this setup.. not even DLNA. So the TV would have to be an extremely smart one to read raw files on a network drive.. none do that I know of.
A solution is WD live TV.. it can read files from just about any file source on network and play them to the TV.
Nothing apple makes will do that.. ATV is a streamer not a media player. Everything in the Apple world is tied up with itunes. So you must have a computer running itunes to use it.
You can download a more generic player for ipad, and put that as part of the network.. but you still need ATV to display the video.

Connecting to Airport Express via Ethernet Cable

Dear Apple Support Community,
My setup at home is such that all my devices are in such close proximity to the Airport Express, and therefore I connect everything to the Airport Express via ethernet cables (NAS, Apple TV, PS 3).
The final step in my network setup would be to connect my Macbook to the Airport Express to connect to the internet using the Ethernet Cables, instead of using the wireless connection - because my Macbook is positioned right next to the Airport Express.
However, I am struggling to get the Macbook to connect to the Internet via the Ethernet Cable through the airport express. Is there a special way to set this up if this can be done. I know Wireless would be the answer, but the problem is, when I download movies etc, I write the files directly onto the NAS which happens a lot quicker than doing so via WiFi.
I hope the above question makes sense.
Thanks in advance for any feedback.
Regards
ST

Hello Brian Hunt1. Welcome to the Apple Discussions!
I have an old PowerBook G3 and I do not have a wireless card for it. My plan was to connect it, via Ethernet cable to my airport express which is on my home wireless network (DSL to Mac Mini to AirPort Express via built-in AirPort).
Unfortunately, the network configuration your describing, where you would use OS X's Internet Sharing feature to share the Mac Mini's wired Internet connection wirelessly with the AirPort Express Base Station (AX), won't work.
If I cannot connect my laptop this way, could anyone suggest a wireless card that is compatible with this slightly antiquated, yet very useful machine?
Only the "Pismo" PowerBook G3 is capable of using the original AirPort card. If you have this model, then the following DIY instructions will show you how to install it.
If this isn't your model, then check out the following vendor offerings:
o QuickerTek
o hField Technologies' Wi-Fire

Hi, I connected to the internet in a different location using ethernet cable and when I got home websites like yahoo wont get to the sign in page and other sites too...weirdly facebook and google works ...please help...tearing my hair out!!!

Question
Hi, I connected to the internet in a different location using ethernet cable and when I got home websites like yahoo wont get to the sign in page and other sites too...weirdly facebook and google works ...please help...tearing my hair out!!!

and now, when i tried to check again my network preference below the airport tab is showing a message that
"my airport does not have an IP address and cannot connect to the internet!"
then after seconds it will goes back to the first message that
"airport has the self assigned IP address etc....."
i don't know whats going on now!
airport tab is not showing green color anyway! i'ts always in yellow!
i tried turning it on and off but nothing happen! HEEELLLLPP!!!!

HT1515 My internet 3rd party access point in in the basement and the speakers I want to stream music to wirelessly are upstairs. Does Airport Express need to be connected to my 3rd party router via ethernet cable or will it stream music wirelessly?

My internet 3rd party access point in in the basement and the speakers I want to stream music to wirelessly are upstairs. Does Airport Express need to be connected to my 3rd party router via ethernet cable or will it stream music wirelessly?

Wirelessly
Just select the option to make your AirPort Express join an existing network in the setup process

I have connected my time capsule to motorola SG6580 modem via ethernet. I have a wireless network on the motorola and a wireless network from the time capsule. I get duplicate IPs error messages sometimes. How do I fix?

I have connected my time capsule to motorola SG6580 modem via ethernet. I have a wireless network on the motorola and a wireless network from the time capsule. I get duplicate IPs error messages (no connection) sometimes when trying to connect devices to the wireless network. How do I fix? Sometimes devices cannot connect to the network because of conflicting IPs. I look on the Motorola and every device has a unique IP assigned but occasionally a device has taken the IP of another device. I have been writing down all the devices and the IPs they have been using. It happens more with PCs than Macs, ipads or iPhones.

If the Time Capsule is set up correctly in bridge mode, then it is the responsibility of the Motorola modem/router to provide the correct IP address assignments for all devices on the network.
Check to insure that the Time Capsule is correctly set up to operate in bridge mode as follows:
On your Mac, open AirPort Utility
Finder > Applications > Utilities > AirPort Utility
Click on the Time Capsule icon, then click Edit in the smaller window that appears
Click the Network tab at the top of the next window
Insure that the setting for Router Mode is configured to read "Off (Bridge Mode)"
Once you have confirmed that the Time Capsule is configured correctly, everything else is the responsibility of the Motorola modem/router as far as network routing and IP address assignments for devices.
If you continue to have IP address issues, then you should contact the Internet Service Provider (ISP) that provided the Motorola device to you and ask them to fix the issue.

How to use Migration Assistant when trying to transfer from MacBook to a new iMac via Ethernet cable

I've been trying to transfer data from my MacBook to my new iMac via Ethernet cable and I get to the point of the transfer starting. Then on my iMac the Migration Assistant shuts down and takes me back to my desktop. Any ideas on why this keeps happening?

Start over, restoring the OS on the new machine, and follow the steps outlined in Pondini's Setup New Mac guide using the Setup Assistant.

Out of the blue, my ITouch is unable to access my wireless network ONLY when my PC has been turned on (PC is connected via Ethernet cable, and has no wireless capability as far as I know). What gives? It works fine when the PC is off.

Out of the blue, my ITouch is unable to access my wireless network ONLY when my PC is on (the PC is connected via Ethernet cable, and has no wireless capabilities that I know of). What gives? When the PC is turned off, everything is totally fine. I\m stumped.

Does the iOS device connect to other networks?
Does the iOS device see the network?
Any error messages?
Do other devices now connect?
Did the iOS device connect before?
Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on your router
.- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
I suspect a problem with your router. Try changing the security. First use no security as a test.
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem and it does not connect to any networks make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

Connect HP laserjet 2100TN to Imac 10.8 via ethernet cable

Similar Messages

Maybe you are looking for