Connect MI424WG to Junos Pulse VPN

I have an Actiontec MI424WG Rev I router that replaced a Rev E router. To get the Rev E to work with Junos Plus client side VPN I had to change the routers IP address from 192.168.1.1 to 192.168.1.2 because it conflicted with the server side ip address I needed to connect to.
I tried this approach with the rev I and it was no go. The first attempt to change the rev I ip address to 192.168.1.2 resulted in a input error "The Device's IP address should not be in the range of the IP pool" so I changed the IP Address Distributions Start IP Address: to 192.168.1.3 I was able to save this config but still not able to connect to the server side ip address.
Verizon level one support would not help. They said as long as the router connects to the internet they meet their obligation. I tried their advance support at $39.95 per hr with no success. I was given an Actiontec support Phone number to try. I thought I would try this board before trying them

Okay, then we know the VPN is working properly though the router. This sounds like a VPN client configuration issue
I suspect you're getting a conflict between the 192.168.x.x LAN subnet used in your home and the same 192.168.x.x subnet used within the VPN connected network. If the VPN client has a configuration option to "allow local network access" try turning that off. That will force it to send all packets through the VPN network. If that clears up the problem then you'll know what the issue is.
If this is the issue and you want to have local network access while connected to the VPN, you may want to change the LAN to use a completely different subnet. 192.168.2,x might work well.
If the entity you're connecting to has an IT support team, they may be able to help you as well.
Good Luck.
If a forum member gives an answer you like, give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem.

Similar Messages

X1 Carbon 2014 - Unable to connect to Juniper (Junos) VPN

Hi,
today I finally received my new X1 Carbon.
I have almost set it up, but have stumbled upon a rather peculiar issue: I am unable to connect to a Junos VPN-server. I am using the built-in Junos VPN-plugin from Windows 8.1 (accessible from the Modern UI Network settings by adding a VPN there). When trying to connect I immediately receive an error message referring to ID "0x800700A1" - path not found. That message is given even before being asked for username or password. The VPN-plugin outputs no events at all to Windows event log (even though it should add such information even when it does not find the server or there is a username mismatch).
Since I am successfully using the exact same configuration on both an MS Surface (non pro) and a Windows 8.1 Desktop computer, I am 100% certain there must be some strange network-meddling on the Lenovo system (e.g. by one of Lenovo's apps). Specifically I fear there is some system file missing or replaced.
I am able to connect using Junipers proprietary software (the "Junos Client"), however that program causes occassional problems on my other computers and is thus not my favorite solution (especially since the built-in VPN can be set to auto-activate whenever a certain IP is called upon and change Proxies on the fly, neither of which is possible with Junipers tool).
Any ideas what might cause this (or what Lenovo app I should uninstall)?
Thanks for any help in advance,
Michael

Check out this thread (http://discussions.apple.com/click.jspa?searchID=5294598&messageID=6406585). The solution is there.

Ios6.1, now unable to connect to junos pulse. anyone else getting this message. connecting using safari

ios6.1, now unable to connect to junos pulse. anyone else getting this message. connecting using safari

Hello Irian and Sue,
I can connect to the Oracle database using SQL Plus. Now when i TNSPING ORACLE from command line i get the following message :
Used parameter files:
D:\app\product\11.2.0\dbhome_1\network\admin\sqlnet.ora
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST =localhost
*)(PORT = 1521)) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = ORACLE)))*
TNS-12537: TNS:connection closed
Thanks for your response to my initial post.Do u have any other methods to resolve this?

Junos Pulse 4.0 not working in Windows 8.1

Hi,
anyone got a Junos Pulse 4.0 release version working on 8.1? After the upgrade from 8 to 8.1 both my Cisco VPN client and Junos Pulse client stopped working because of resp. a yellow triangle for the Deterministic Network Enhancer and the Juniper Miniport
WAN driver. Via the Citrix page I updated the DNE and this solves the problem for the Citrix VPN client, but this Juniper Miniport WAN driver problem remains and actually totally destroys the network stack. It adds the faulty driver to all NICs making them
unuseable.
JP4 is not officially supported for 8.1 until release 4.0R7, however release 4.0R6 should take care of the most critical probleems. But the problem with the drivers existed from release 4.0R3.
I've tried removing drivers, registry entries, software and reinstalling many times but unsuccessful thusfar.
Much obliged
Marcel
PS version 4.0R7 won't be available until december.

Hi ctaggart,
thanks for the follow up. From the Supported Platforms Guide (http://www.juniper.net/techpubs/software/pulse/releasenotes/j-pulse-5.0r1-supportedplatforms.pdf)
I do get the impression the 32bit Windows 8.1 is not fully supported. For some reason IE11 (standard in 8.1) is not on the supported browser list for 32bit, only for 64... A bit odd but maybe not relevant in my case.
But, I've received the 5.0R1 version (32bit) and installed it (created a restore point to be safe).
First try: immediately a blue screen of death when installing the drivers.
Second try; the software installed successfully but unfortunately the thick Junos client still is unable to secure the connection. The Juniper Networks Virtual Adapter (still) cannot be loaded. I verified the version of the driver: jnprva.sys which seems
to be the same as earlier releases: 5.40.0.27939.
The Junos Log files do not really help.
When I look at the Device Manager I still see that annoying 'Juniper Network Agent Miniport' appear behind each network adapter. But at least the warning sign for that thing is gone everywhere! The only warning that remains is the JNVA, however I'm pretty
sure that all those 'duplications' are not a good sign.
Another good sign is that my other VPN clients (Junos built-in and Cisco) still work(!), so a restore is not required at this point.
The reason I need to get this client working is that the Built-in client cannot access VPN urls such as
https://vpn.mysite.com/employees and this is (unfortunately) how it is setup by our admins.
Frustrating....
Marcelio

Not able to connect remote oracle database over VPN

I can not connect remote oracle database over VPN. tnsping is ok and it shows the server information of remote database. i can also telnet the 1521 port of remote database server. I can connect the same server when it is located in the same LAN. Please help me out this is very urgent.

6b6c669e-6baa-45c4-a6dc-444aef2d5e7a wrote:
I can not connect remote oracle database over VPN. tnsping is ok and it shows the server information of remote database. i can also telnet the 1521 port of remote database server. I can connect the same server when it is located in the same LAN. Please help me out this is very urgent.
First, this is a forum of volunteers. There is no "urgent" here.
"Urgent" means one of two things -
1) people are dying, or
2) you have a customer-facing, revenue-producing production system that is down.
(And to get some perspective on the second case, keep the first in mind.)
For the first, you call whatever civil emergency service seems appropriate.
For the second, you open an SR with Oracle - which requires a paid-up support contract. For *them* to consider your problem "urgent", you will need to demonstrate that your problem falls under item #2. I seriously doubt your problem fits that criteria.
You don't have a support contract? Now you know the exact dollar figure that your company places on the data.
That said, you need to understand a few things about your specific problem,
First, port 1521 is only used by the listener to accept a connection request. Once it gets that request (and finds that it is for a service (sid) that it knows about, it will fork a server process and tell the requesting client that it can communicate with that server process over some other port .. a randomly chosen port number in the "high" range. It could be your vpn is blocking that other port, whereas your internal firewall is not.
But this is just an educated guess since I cannot find "can not connect remote oracle database over VPN" in any error message manual. If you had mentioned the VPN along with an actual oracle error message we could be much more precise in our diagnoses and recommendations.
---- edit 22 Sep
It occurred to me that I just assumed you were using the same client machine in both cases ... a laptop that you use both at work (local network) and home (vpn). If that assumption is false, there are probably problems with your tns setup on the home (vpn) machine.
But again, it would be much easier to help if you gave us an actual error message.

Since the last update I can no longer connect remotely to an SSL VPN system

I connect to work remotely (SSL VPN site, whatever that means), and was always able to do so successfully until this week. I can reach the log-in site, my password is accepted, but then when I click "Connect", I am left forever on the screen that says, "Launching Connection, please wait..."

Hello jmichel216,
It sounds like you are unable to connect to any Wi-Fi network after updating your iOS version. I recommend the troubleshooting from the article named:
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/ts1398
Restart your iOS device.
Unable to connect to a Wi-Fi network
Verify that you're attempting to connect to your desired Wi-Fi network.
Make sure you're entering your Wi-Fi password correctly. Passwords may be case sensitive and may contain numbers or special characters.
Reset network settings by tapping Settings > General > Reset > Reset Network Settings. Note: This will reset all network settings including:
previously connected Wi-Fi networks and passwords
recently used Bluetooth accessories
VPN and APN settings
Thank you for using Apple Support Communities.
Take care,
Sterling

Connecting to BW system through VPN in Design Studio

Hi Experts,
I tried to connect to my client BW system through VPN and used the URL in my Design studio, but when I connect like that the Design Studio is working very slowly and hanging several times, If I connect to the same system via Lumira it is working fast.
Can you please suggest me what are the cautions I need to take when I connect to BW system via VPN to make my Design Studio work fast with out hanging several times on my local system.
Thank you,
Hari

Hello Hari
remember that Design Studio is a live connection and in Lumira you can use a BW offline connection which downloads the data.
regards
Ingo Hilgefort, Visual BI

We are unable to connect to Integration builder through VPN.

Hi,
We are unable to connect to Integration builder through VPN.
Below are the errors we get:
a. In two of the PI 7.0 Systems we get:
     i. Cannot open connection on host x and port y.
     ii.com.sap.engine.services.rmi_p4.P4IOException: Cannot open connection on host: x and port:y
     iii. java.net.SocketException: Malformed reply from SOCKS server
b. In the other two PI 7.1 systems we get:
     i. MESSAGE ID: com.sap.aii.ib.core.ejbutil.rb_all.SERVER_NOT_AVAILABLE
     ii. com.sap.engine.services.jndi.persistent.exceptions.NamingException: Exception while trying to get InitialContext. [Root exception is com.sap.engine.interfaces.cross.DestinationException: cannot establish connection with any of the available instances:
uvw.xyz.abc.net:51504 Reason: com.sap.engine.services.rmi_p4.P4IOException: Cannot open connection to host: x and port:y]
     iii. com.sap.engine.interfaces.cross.DestinationException: cannot establish connection with any of the available instances:
uvw.xyz.abc.net:51504 Reason: com.sap.engine.services.rmi_p4.P4IOException: Cannot open connection to host: x and port: y
The hosts and ports are accessible. (Telnets and tracerts work fine for all the systems)
We are able to access the SLD and Runtime workbench on all the environments. However, Integration Builder tools are not accessible.
Any clue on what the problem might be?
Thank you,
Siva.

Hi Siva,
When you execute SXMB_IFR from PI, do you get Integration Builder page?
Are you trying to directly access the PI server by the known URLs?
Also, Following links may be of your use:
Integration Builder -Configuration is not openning?
Re: unable to logon to Enterprise Services Builder or Integration Builder
Regards,
Nipun

I'm trying to connect to my work's VPN. I am connected to the VPN, but I cannot access the server. I keep getting a message that says the server may not exist or is unavailable. I know that's not the case because my coworkers are connected. Can someone

I'm trying to connect to my work's VPN. I am connected to the VPN, but I cannot access the server. I keep getting a message that says the server may not exist or is unavailable. I know that’s not the case because my coworkers are connected. Can someone please help me?

I have the same problem. It is only with tv shows and only with programs I have downloaded after the software update.
Apple support sent me the above link too....but it doesn't solve the problem...my computer is authorized and the content is in my library and will play on my Mac air, but it will not sync the tv shows, it keeps saying my computer isn't authorized for it.
No answers here, but you are definitely not alone with this issue.

Junos pulse on a macbook air?

I found Junos Pulse in the app store, but that doesn't work for the macbook air. alternatively i have visited the juniper network website, but downloads require extensive registration and from what i can tell some type of contract for access. am i missing something?

Junis Pulse is coded for iOS which runs on mobile device.
Your MBA is a computer and runs OS X which is not capable of running apps coded for iOS

IOS can't connect to Lion Server's VPN or navigate to /mydevices

I've configured my host name, some seperate services for my VPN and now I'd like to introduce my iPad 2 to the mix as well.
However each time I go to navigate to - http://server.myserver.private/mydevices, safari says the server cannot be found.
Ontop of all this, I'm having a huge time trying to even connect the iPad to my VPN as well saying "VPN Connection - the server is unreachable. Try reconnecting"
If anyone is able to give some sort of guidance, I'll be in their debt!

Hi - I am also having the same iPad/VPN problem.
Did you find any solution to this?
Regards
Michael

Client Computer cannot connect to server over internet (VPN)

Hello Guys,
I am setting up a windows server 2012 Data centre for business purpose. I have installed & configured server with AD DC, DNS, DHCP, IIS, NPS, Routing etc.. I am able to connect client computers which is on the same domain to the server through same router.
VPN also work fine. But if I try to connect to the server via VPN through a different internet connection it won't connect. Can some one please tell me what I am doing wrong.
My Network Confg is,
DHCP IP ADDRESS FROM ISP
DHCP Disables Router, (Tried with enable)
Have my own website domain which is not linked with the server.
NAT not configured.
Thanks in Advance
Emmanual.

Hi Emmanual,
Thank you for posting in Windows Server Forum.
Can you ping to the remote server after connecting through VPN?
Did you find any specific error\event id for your case?
What’s your client OS version?
If you are not getting ping successfully then seems there is connection issue through VPN. So for this you can initially check the connection setting with following article.
You Cannot Connect to the Internet After You Connect to a VPN Server
http://support.microsoft.com/kb/317025
There are several reason as client is not getting remotely connected to server. In addition you can checl following article.
Enabling remote client access over a VPN connection
http://technet.microsoft.com/en-us/library/cc995159.aspx
Hope it helps!
Thanks.
Dharmesh Solanki
TechNet Community Support
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Version 4.x release for Junos Pulse Client Support

Looking to know version 4.x expected release date to support the Juniper Junos Pulse Client.
Thanks

iOS 4 for iPad expected sometime in the fall of 2010. No additional info available until Apple announces it.

Does anyone know if there is a special macbook air app for Junos Pulse

My company used SAP, and I'm trying to gain access w/out having to boot up into a windows environment on my macbook air. I was told I could use the app Junos Pulse and download the SAPGUI locally. Is there a app specially for the the macbook's and has anyone tried this?
Thanks

there is indeed a Mac OSX Junos Pulse client.
You can download it here:
http://www.juniper.net/support/products/pulse/3.0/#sw

Junos Pulse for Playbook and 9850

I see that all BB smart phones except the Torch 9850 and the Playbook can access Junos Pulse. I have become a developer and have coverted android apps and installed multiple applications but am unable to do so for Junos Pulse. I am a physician who does not want to use our hospitals bulky Ipad and there is no mouse in the attached bluetooth keyboard. I love my Playbook and the OEM keyboard. Please, please, please, configure Junos Pulse for Playbook and the Torch. It is essential to have at least the tablet in our healthcare environment.

For your request you need to contact the developer to have the app ported to the playbook.
Be a Shepard and not an iSheep.

Connect MI424WG to Junos Pulse VPN

Similar Messages

Maybe you are looking for