Connect more than 1 external BI in SEM-CPM-BSC or SEM-CPM-MC

Hello,
I have seen the help.sap.com that helps me how to put a defined BI (but only one BI).
Design -> Default BW System
Design -> Access to SAP BW
Design -> RFC Destination for Project System
But what we have is 3 BI systems. Each one with one module (HHRR, FI, SD). We want to join those BI modules into the SEM CPM. But I don't see how to put those 3 external BI in my CPM.
Please help me...
Best Regards...
Pablo Mortera.

There're several ways:
1.- Create remote Cubes where you get your queries. Then once the SEM system you will have a Cube that really is a "remote" cube in another system. This will also help by creating a MultiCube, related to the cubes created before...this way you have a big datamart (really a knowledge mart;-) ) that has all of the data/information related in one view.
2.- In the local BW system, you may create local InfoProviders that are being fed by remote BW systems as InfoSources. (You'll have to create the InfoSources and copy the data loads in the local BW System)
Hope this helps.
Cheers.
Jesus

Similar Messages

Connect more than 3 ATV's at the same time to one iTunes Library.

Seriously! Im about to go nuts on this!
I have a big problem, I have 13 ATV's, 1 x MacMini witch has two external drives on 1TB containing film attached to it.
I want to be able to connect all the ATV's to the same iTunes library, I know that you cant stream to 13 ATV's simultaneously. I just want them to be connected to the library so i dont have to run to the computer to connect another one just because you change location inside the boat.
I have been in contact with Apple Pro support numerous of times regarding this and the only answer you get it pretty much.. this is the way it is.. like it or not..
Have contacted Royal Caribbean Cruise ships yard down in Miami to try getting hold of the guy who had to do with the 1400 iMacs the had installed on their vessels. Not received a reply from him yet..
Does anyone else have any tips on how I can approach or try to contact?
I know that me with my few ATV's is a man with no voice when it comes to speak to Apple about this problem.. But the thing is that i am working as an IT Officer on a private owned yacht 70m+ and have allot of contact with other IT guys from other private owned vessels (read hundreds of hundreds private owned yacht around the globe) how was like me.. looking for a nice, quiet good looking pice of equipment with a nice, easy to use interface that isn't going to cost 100 000€.. If you start looking at it in that way, my 13 ATV' all of a sudden could been 1300? or maby even 13 000? when you start counting on potential yachts around the globe..
I mean i understand why Apple have limited their iTunes to not be able to handle more than 3 ATV's at the same time.. but i still think its wrong to cut all possible changes to make it able to connect more than 3 external medias to the same library. They could have made a solution like what they have done with the Quicktime for example.. the player that comes standard in OSX is the basic one.. go online pay "what ever amount" and whips you have a pro version.. could have done exactly the same thing when it comes to iTunes.. basic pre installed.. buy a code in apple store and whips you have pro features..
It cant just be me in the hole world ho has this problem?!?!
Incredibly grateful for answers or thoughts.
Best regards Timpos

AC, Thank you for you reply.
Even though it is supposed to be a 'simple' home video system it has so much potential!
And i mean i know there is an solution since i know the Caribbean cruises are using apple as media centers onboard their ships. have to admit that i do not know if they are using frontrow or some other application created buy some other company.. i just know that some one must know how to get around it all and make it work..
Just wish i had someone to get in contact with that is working hands on every day with this product, and get strait, good, final answers.. no "pro support" since im not happy with their answers anymore..
I know i start to sound desperate.. but thats because i am..

How to load and unload more than one external swf files in different frames?

I do not have much experience on Adobe Flash or Action Script 3, but I know the basics.
I am Arabic language teacher, and I design an application to teach Arabic, I just would like to learn how to load and unload more than one external swf files in different frames.
Thanks

Look into using the Loader class to load the swf files. If you want to have it happen in different frames then you can put the code into the different frames.

Can I use a USB hub to connect more than 1 hard drive/flash drive device to the EA4500?

Can I use a USB hub to connect more than 1 hard drive/flash drive device to the EA4500?

That's not possible, it was designed to handle one device at a time.
I don't work for Cisco. I'm just here to help.

Hello! I have in my home 2 iMac, 2 iPad, 2 iPhone, and 1 air base extreme. I don't succeed to connect more than one divice from similar type. I tried everything what I knew. I build another network, etc...

Hello! I have in my home 2 iMac, 2 iPad, 2 iPhone, and 1 air base extreme. I don't succeed to connect more than one divice from similar type. I tried everything what I knew. I build another network, etc...
So only one imac, only one ipad..and so on simultain.
More over, all the divices are conect through wifi to air base but are not receiveing internet as i told above.
I need to disconnect one device to have internet on the second one from the same type!
Could somebody help me?
Many Thnaks,
dan

If your network configuration is:
Cable modem > (Ethernet cable) > [WAN] AEBS > (wireless) > Macs, then
AirPort Extreme Base Station Setup (AEBS) w/High-Speed Cable Modem
Modem/Router Power ReCycling
- Power-off the Cable modem, AEBS, & computer(s). (If possible, leave the modem off overnight.)
- Power-on the Cable modem; Wait at least 30 minutes.
- Power-on the AEBS; Wait at least 5 minutes.
- Power-on the computer(s)
Perform a "hard" reset of the AEBS.
- (ref: http://docs.info.apple.com/article.html?artnum=107451)
Setup the AEBS
With the network components powered down, set up the AEBS, using the AirPort Admin Utility, connect your computer directly (using an Ethernet cable) to the LAN port of the AEBS, and then, try these settings:
AirPort tab
- Base Station Name: <whatever you wish or use the default>
- AirPort Network Name: <whatever you wish or use the default>
- Create a closed network (unchecked)
- Wireless Security: Not enabled
- Channel: Automatic
- Mode: 802.11b/g Compatible
Internet tab
- Connect Using: Ethernet
- Configure: Using DHCP
- WAN Ethernet Port: Automatic
Network tab
- Distribute IP addresses (checked)
- Share a single IP address (using DHCP & NAT) (enabled)
Once you verified that you can get Internet access for all of your computers, you should secure your wireless network. To do so, I suggest that you make these changes:
AirPort tab (optional)
- Create a closed network (checked)
Change Wireless Security
- Wireless Security: WPA Personal
Base Station Options - WAN Ethernet Port
- Enable SNMP Access (unchecked)
- Enable Remote Configuration (unchecked)
- Enable Remote Printer Access (unchecked)
Wireless Options
- Transmitter Power: 10%
Access Control tab (optional)
- + <add the computer(s) that will access this wireless network>

Can't connect more than one device.

I just bought an Airport Express 2 gen from a friend and I have two issues: I tried to reset it to factory settings and could not do it. Tried holding the reset button for 10 secs, unplugging and plugging back in while holding the reset button, holding the button for a longer time and nothing worked. I had no choice but to create another network. Once created, I can't connect more than one device. If I have my MacAir hooked up the network and I try to get my Ipad in, the minute I type the network pass in my Ipad, a screen pops up where I have to log in with my internet provider account. When I do that, it will connect, but my MacAir will disconnect automatically.
Appreciate any help!

Things are a bit different with the 2nd Gen AirPort Express and other newer AirPorts.
A Factory Default Reset is now the same as what was previously known as a "Hard Reset".
Power up the AirPort Express and let it run a few minutes.
Hold in the reset button on the Express for 10 seconds
Release the reset button and allow a full minute for the Express to restart to a slow, blinking amber light
If the Express is operating correctly, it will be back to factory default settings at this time.
If you try the reset a few times and the Express will not return to default settings, the Express is defective.

Can Not Connect More Than One Device

Does anyone else have the issue of not being able to connect more than 1 device to your wireless network without it timing out and resetting the router? I pay extra to have what they say is the fastest internet but it never works. If Apple TV is streaming Netflix my iPad, my laptop and my desktop all have to be off and not connected to the WiFi or the router resets itself. My speed test actually timed out because it was taking so long both times I tried it, a month apart. I had the same issues before switching to X1 and getting my new WiFi modem. If I call I just get the run around and have my modem reset a dozen times with the exact same outcome...

It would help if you post the model of the device.
Also look over the troubleshooting tips and post the downstream RF power levels, downstream SNR and upstream power levels on all channels.
http://forums.xfinity.com/t5/Basic-Internet-Connectivity-And/Connection-Troubleshooting-Tips/m-p/1253575#U1253575

Error 5006: can't have more than one externally visible definition

Hi
I'm getting this error:
5006: An ActionScript file can not have more than one
externally visible definition: AMReports, playSound.
playSound is a function in my main document class
The error occured after I added a MovieClip and FLV component
to my the same framemain timeline. This Movie Clip has 3 frames.
I'll be using cue points added to the FLV component to move this
from frame to frame in that MovieClip.
Any one have an idea why this is happening?
Thanks.

I fixed this problem: a brace was in the wrong place.

Error when connecting more than 50 users ??

I use database 8iEE & form server (9ias rel1) on different box to deploy form on the web
the error occur when user connect more than 50, but it's ok when connect to database using sqlplus
Is there someone has the same experience ?

I think this problem has been addressed and answered in this forum time and again …
Opening files or creating new files while in Full Screen Mode will cause a cursor offset in Photoshop CS4 (I don’t know if there are configurations where that does not happen, but best assume it just does); the common remedy is circling through the Screen Modes by hitting F on the keyboard three times.
Edit: The matter doesn’t seem to have made it into the FAQ, though. Maybe someone could add it there?

Can you connect more then one external screen to a mac with one mini display point?

Does any one know if you can connect more then one external screen to a mac, with one mini display point?

This company has a dual monitor solution for DisplayPort;
http://www.matrox.com/graphics/en/products/gxm/dh2go/

Connect more than one computer to a time capsule volume?

Hello. I am considering buying an old time capsule (500G, 2nd generation) as a little in-house server to store data that need to be accessible for more than one work station. Is it possible to connect more than one work station to one time capsule?
Thanks

While it is possible to connect more than one computer to the Time Capsule......I would not recommend that you buy the Time Capsule that you are looking at.....unless you know that the owner has replaced the hard drive and power supply.
Most of these models never made it much past a few years of operation, so if this is an "original", you have a hint of what will happen not long after you purchase the product.

HT201210 Iphone 5 can not save my router of 2.4ghz and does not connect more than 3 minutes but Iphone 4s has not that problem in the same router.

My iphone 5 is not saving my unlocked router. My router is linksys and is 2.4 ghz, My other devices such as iphone 4s and ipad2 have not had that problem with router. My iphone 5 connects hardly to my router but does not stay connected more than 3 minutes within the range.

Try rebooting your router by removing all power from it for about 15 seconds.

Cant Connect more than 8-9 devices

I have the original "Mushroom" Airport. Why can't I connect more than 8-9 devices at a time? Tech specs says I can connect up to 50. But havent been able to do more than 8-9 depending on connection order.
I'm trying to connect the following
2 Wii's (Though only 1 would be active at any given time)
2 MBP
2 iPads
2-3 iPods
2 iPhones
1 PC Laptop (win7)
1 Wireless Printer (HP)
I'm running all updated softwares, SL and Airport. and including softwares on the connecting devices. Any thoughts, tips...

I have the original "Mushroom" Airport. Why can't I connect more than 8-9 devices at a time? Tech specs says I can connect up to 50. But havent been able to do more than 8-9 depending on connection order.
I'm trying to connect the following
2 Wii's (Though only 1 would be active at any given time)
2 MBP
2 iPads
2-3 iPods
2 iPhones
1 PC Laptop (win7)
1 Wireless Printer (HP)
I'm running all updated softwares, SL and Airport. and including softwares on the connecting devices. Any thoughts, tips...

Connecting more than 6 wireless devices to homehub...

how can i connect more than 6 wireless devices to homehub 3? my current cable provider allows me to have 9 wireless devices connected at the same time
is there a way to connect a wireless router to homehub 3 or do i need to invest in a modem router from another make that allows me the extra connectivity?

Hi you can have as many wireless devices as you wish the same applies to wired connection's if you use an Ethernet switch all you need to do is enter the wireless security code into each wireless device
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Connecting more than one ipod to one mac computer

Can anyone please advise me on how I can connect more than one ipod to just the one mac computer. I need to set up 3 ipods to work on the one mac computer but each with there own itunes library. thanks

When the iPods belong to two users, there are a couple of recommended methods for using more than one iPod on a single computer. Method one is to have individual Mac or Windows user accounts which by definition would give you completely separate libraries. Each account has it's own iTunes folder, Library and iTunes Music folder and you load it with CDs etc just as you did with your original one. Each iPod can be set to update however the owner chooses, sync all, manual or sync specific playlists.
Method two is to set your preferences so that either one or both iPods get updated with only certain playlists within one library. Have a look at this article and see what you think and go for whichever you feel suits your needs best: How To Use Multiple iPods with One Computer
Another option when using a single library is to set one or both of the iPods to manual update: Managing content manually on iPod
Choosing the update option "automatically update selected playlists only" (called Sync Music - Selected playlists in iTunes 7) allows you to create a playlist specifically for each iPod and drag the tracks you want into it. If you tire of the list and want to change it, you just add or remove the songs you don't want. The ones you take out out remain in the library to be used by the other iPod. Make your playlist a Smart playlist and limit the size to just below the advertised capacity of your iPod ( for example, around 3700MB for a 4GB or 1800MB for a 2GB Mini or Nano). You can read more about playlists at these links:
iTunes: Creating playlists of your favorite songs
How to create a Smart Playlist with iTunes

Connect more than 1 external BI in SEM-CPM-BSC or SEM-CPM-MC

Similar Messages

Maybe you are looking for