Connect Samsung TV to AirPort Express Wi-Fi

How can I connect a Samsung Smart TV Model 6150 to a Apple AirPort Express 802.11n Wi-Fi Model A-1264?
TV will not recognize my network. iPad connection is OK.

Did you Samsung TV come with a USB WiFi modem? All the new models do. You need to plug this into one of the USB port on your Samsung TV.
As for your Airport Express, it can only create a Wireless (WiFi) network for you, it does not have any Ethernet ports as you already know. @Bob is correct that the USB port on the Airport Express only supports compatible printers; for sharing the printer on your network.
Do NOT connect the TV via wired Ethernet to your modem supplied by your broadband provider (ISP). That's because you need to "dial up" to your ISP, if you do not have another router than the Airport Express, then the Airport Express is doing this for you.
So if your TV did not come with a USB WiFi modem then you may want to contact Samsung to see if you get get one. BTW if you live in the US Samsung is available on Twitter (@samsungservice

Similar Messages

Can't connect to an extended Airport Express?

My network is set up in the following way (see photo) 1 Time Capsule + 2 Airport Express to extend the network.
No computers or devices can connect to the Airport Express named "AE02"? They all ONLY connect to the middle Airport Express called "AE01" even though they are like 20 cm from AE02??
What am I doing wrong? Anyone else has this problem?
Thanks

Thanks, Huge bummer... How come the Airport Expresses connect that way if not allowed?!
I found the answer just like 'Tesserax' pointed out.
Here:
http://support.apple.com/kb/HT4145

Can I set up to connect 2 or 3 airport expresses to have a stronger wifi signal for a larger area?

can I set up to connect 2 or 3 airport expresses to have a stronger wifi signal for a larger area?

Theoretically yes. It will really depend on your situation. Please review the following Apple Support article to understand what is possible with the AirPort base stations and post back with any questions or help in setting up your extended network.

Can't connect (wireless) to my Airport Express anymore with iBook, iPad or iPhone.

Can't connect (wireless) to my Airport Express anymore with iBook, iPad or iPhone. It still recognizes the printer on the iBook (bonjour), but not on my Windows notebook (work). The only device that still connects via wireless is the PlayStation 3.

The latest firmupdate solved the issue.

Can I connect an A1084 model Airport Express using current version of Airport Utility

Can I connect an A1084 model Airport Express using current version of Airport Utility?

You will need an older 5.x version of AirPort Utility to be able to administer the older AirPort Express. That would mean that you need to have....or be able to borrow for 10-15 minutes......a Mac running Leopard (10.5.x), Snow Leopard (10.6.x), or a PC with AirPort Utility installed on the device.

Can I extend my network by connecting one of my airport express devices to my airport extreme via an ethernet cable? I have CAT5 cable throughout my house but have a wireless network w/ 3 airport expresses

Can I extend my wireless network by connecting one of my airport express devices to my airport extreme via an ethernet cable? I have a wireless network with 3 airport expresses and 1 airport extreme functioning as the base station. I have CAT5 throughout my house.

Welcome to the discussions, mib88!
Can I extend the network a second time with another Airport Express...
The short answer would be no. If you want more details, please continue to the next paragraph.
Apple's "extend a wireless network" works just like the hub and spokes of a wheel. Your main hub is either the Time Capsule or the AirPort Extreme and the AirPort Express is at the end of a spoke. You can add more devices at the ends of other spokes, but these devices will communicate directly to the hub, not to another device at the end of a spoke.
Apple does offer an option which is is known as a "static WDS", which can consist of a "main", "relay" and "remote" device. The problem here is that this type of setup has two huge drawbacks:
1) All of your faster "n" devices will drop down to much slower "g" speeds
2) The bandwidth or speed capability on the network will drop down to only 25% of the original bandwidth with a "main", "relay" and "remote" on the network.
Don't think you want this on your network. Your best option is to connect the new AirPort Express to the "hub" using an ethernet connection. If you can't run the ethernet cable, take a look at a pair of ethernet powerline adapters to accomplish the same task by sending the ethernet signal over the AC powerline in your home.

Connecting a Laptop to Airport Express via Ethernet Cable

I have an old PowerBook G3 and I do not have a wireless card for it. My plan was to connect it, via Ethernet cable to my airport express which is on my home wireless network (DSL to Mac Mini to AirPort Express via built-in AirPort).
My question is can I make this work? After buying the Ethernet cord, all my reading of the AirPort Express manual seems to suggest that the Ethernet port on the AirPort Express is to only be used as an input port, not as an output. Is this correct?
If I cannot connect my laptop this way, could anyone suggest a wireless card that is compatible with this slightly antiquated, yet very useful machine?

Hello Brian Hunt1. Welcome to the Apple Discussions!
I have an old PowerBook G3 and I do not have a wireless card for it. My plan was to connect it, via Ethernet cable to my airport express which is on my home wireless network (DSL to Mac Mini to AirPort Express via built-in AirPort).
Unfortunately, the network configuration your describing, where you would use OS X's Internet Sharing feature to share the Mac Mini's wired Internet connection wirelessly with the AirPort Express Base Station (AX), won't work.
If I cannot connect my laptop this way, could anyone suggest a wireless card that is compatible with this slightly antiquated, yet very useful machine?
Only the "Pismo" PowerBook G3 is capable of using the original AirPort card. If you have this model, then the following DIY instructions will show you how to install it.
If this isn't your model, then check out the following vendor offerings:
o QuickerTek
o hField Technologies' Wi-Fire

Anyone has an idea how to connect and configure my Airport express to an internet range extender which is plugged into mains

Anyone has an idea how to connect and configure my Airport express to an internet range extender which is plugged into mains?
Message was edited by: m. emin

You can connect it but with ethernet cable. You can not connect it by wifi to extend the range a second time.
BTW AE is rather sensitive to connect by wifi to non-apple wifi routers.

Connecting to Comcast using airport express

My wife bumped the Airport express router that connects to our comcast modem. I unplugged both, reset the comcast modem, waited 3-4 minutes, then plugged the airport express router back in the socket. Went downstairs, couldnt connect to the internet according to the airport express utility application. Green light on airport express, orange light on the "Internet" in the utility. Called Comcast, total waste of time after 1.5 hrs of "tech support" was told to call Apple . Computer is 4 years old, has been working fine up to this point. Apple wants me to pay $49 for support. nothing guaranteed.
Any suggestions? I've tried turning off IMAC, running upstairs, unplug airport express, unplug modem, push reset on modem, wait 4 minutes for modem to fire back up, plug airport express back in, run downstairs, turn on IMAC, run airport express utility and same result, green for airport express router, orange for internet.
Opened up Safari, tried network diagnostics troubleshooting, it eventually asks me if we are DHC? or PPPoE. I choose PPPoE and enter comcast for service provider, enter username and password (as verified by Comcast) during my 1.5 hour session. trys to connect. goes back to same screen of do we have DHCP or PPPoE.
Frustrating!
Neighbor told me to plug IMAC directly into Modem and see what happens using an Ethernet hard connection. Will try tonight.
Any assistance is appreciated.

Bob,
I plugged the Ethernet directly into my Imac, clicked on DHCP, and I was connected. Plugged my airport express back in, unplugged cord from computer back to airport express, waited for green light on airport, tried to connect to my network, unable to get to the Internet. Wifi was on, just not able to connect to the internet.
So, I unplugged again, plugged ethernet cord into computer, back on the internet.
Puzzled. Airport seems to be working fine, amber light when first plugged in, green light after a few minutes.
Tried plugging in airport to comcast modem, reset modem, waited 5 minutes, tried to connect to internet, not able to do so.
Airport utility says airport express is fine.
needless to say, Im at a high level of frustration. Never ever had a problem this bad.
wondered if I unplugged airport express for 24 hours, then tried again, hoping it would clear out any memory on board and start the whole process of creating a new network over again.
Suggestions?
Thanks by the way.
George

Unable to connect to Internet via Airport Express - 'cannot contact server'

I'm unable to connect to the internet via my Airport Express. I'm using OS 10.3.9, and had the same setup with no problems at a previous address, but with a different modem from the same ISP.
My AE is connected - the light is green - and my mac is connected to the network in Internet Connect. But when I open Safari I get an 'unable to contact server' message.
I've tried rebooting everything (modem, AE, Mac), and leaving modem/AE off for several minutes. Also reset the AE, but to no avail.
The connection works fine via Ethernet cable.
Any ideas?

Thanks, I checked out that advice doc (106798), but could not connect to the address (http://17.149.160.49) which is given to test if it's a DNS issue. My ISP says I shouldn't need DNS settings.
The service is PPPoE, and I went into Airport Admin Utility to check if the Airport was configured for this. Under Configure/Internet, I found it was set to 'Ethernet', so changed it to PPPoE. Then when I restarted I got connection status in the bar (and good Airport signal), but status flipped between 'looking for PPPoE host' and 'negotiating PPPoE host', sometimes sticking on one or the other each time I tried rebooting all gear.
Any other ideas?

How to connect apple tv and airport express on same Hi-Fi?

Hello everybody,
My question first : Is it possible to output the sounds directly from the Apple TV to my Airport Express (via Airplay, wifi, or whatever connection) and connect with the jack my Airport Express to the stereo? This way I could hear the sound from my tv or listen to my music via airplay the way I want.
Now, the long explanation : I have a Tivoli sound system which only has a Jack as input plug. I also have an Apple TV (2) to watch movies. For my movies, as my stereo doesn't have any optical audio input, I've connected the television directly to the stereo. As I used to listen music from my Iphone on the dock aswell, I installed a double jack adaptor to permit two connections to my stereo (1 for the iPhone dock and 1 for the television).
Now things have changed a bit. I bought an airport express to replace the dock station.
The problem is that I can't use the double jack adaptor anymore. If I want to watch tv I have no sounds from stereo until I unplug the airport express Jack. The reverse works, I can listen to my music when both airport Express and television are connected.
If you have an idea? Let me know.
Thks.
Christophe

....... Is it possible to output the sounds directly from the Apple TV to my Airport Express
Unfortunately not.

Printer problems connected to iMac using Airport Express

I have an Airport Extreme functioning as a base station,and an Airport Express extending the range to an iMac i keep on the third floor of my house; my HP printer is connected to the iMac. My iBook laptop in my kitchen connects wirelessly to the base station's stronger signal. Previously, when I used a Linksys system, my laptop was able to 'see' the printer connected to the iMac; now I can't. (I also am unable to fileshare between the computers, even tho i have filesharing switched on.) What gives (on both the printing and filesharing questions)?

If you run the Airport Admin Utility on the iBook - does it "see" both the Airport Extreme Base Station and the Airport Express?
Double check that your broadband modem is connected to your Base Station's WAN port - that's the port labelled with the "circle of dots" icon.

Problems connecting Canon MP780 to Airport Express

I am at a complete loss.
Here is my problem ; my Airport Express turns down everytime I connect my MP780 printer to its USB port.
I am working on a Imac G5, running OS X Tiger 10.4.3, I am connecting to internet via an Ethernet modem via PPPoE and Airport Express (Airport 4.2)
1/Cannot set up the Airport Express as long as the printer is connected to the USB port : the Airport Admin Utility freezes.
2/I can set up the Airport Express and connect to Internet as long as the USB port is free, but as soon as I connect the printer to the USB port, Airport Express shuts down, restarts & gets reinitialized all by itself.
Does any have an idea of what is going on?

Thought that fellow Canon MP780 users would find this reply from Canon just as frustrating as I did. Time for a manufacturer change.....
Canon E-mail Reply:
Thank you for writing to us about your PIXMA MP780. We value you as a
Canon customer and appreciate the opportunity to assist you.
Canon does not directly support sharing or networking the printer using
Apple's Airport base station or access point for wireless printing.
You
should refer to the setup information and directions provided with the
Airport. The printer should generally be set to print to Rendezvous
which handles communication with the Airport and printer.
With this said, many Mac users share and successfully print with their
Canon printers using the Airport, but it should be noted that Canon
does
not support printing unless the printer is directly connected to a
native
USB port on the Mac. If you are having an issue printing when using
the
Airport, you should retry printing with the printer directly connected
to the USB port on the Mac.
Please let us know if we can be of any further assistance with your
PIXMA MP780.
Thank you for choosing Canon.

Connecting wireless modem and airport express

I currently run internet with an old Motoirola Sideboard cable modem and Airport Express - previous version. All runs well. Now my Optus provider has upgraded my service with a Premium account for higher speed. They have also given me a free wi fi Cisco modem - DPQ3925. How can I replace my old Motorola modem and still maintain Air play etc with my new modem using Airport Express. I need to know exactly wire per wire help - please, if possible - Thanks
Mac

Hi - I have a similar issue.
I have a new macbook pro, ATV (3rd Gen) and AXn (purely for Airplay of itunes).
All three are wirelessly connected to my HG556a Huawei WiFi Router.
The Macbook pro and ATV work fine and can see each other for airplay mirroring and itunes.
The AX connects and comes up in Airport Utility (AU) and itunes shortly after you turn it on, but if you either dont use it or stop using it and switch to ATV or whatever it dissapears from itunes and AU says it cant find it. Randomly the light on the AX stays green the whole time.
I have to switch the AX off and on to get it back working again (i.e. itunes and AU can see it).
Following other forum posts I've set the AX up by hard connecting it to my router, setting a static iP and reserving ports 5353 and 3689 to that address. I've also turned off ipv6 or whatever using the networksettings Terminal code string. I have also repaired permissions with disk utility!
It still dissapears from available options in iTunes and AU. ideas?

ITunes cannot connect to remote speakers / Airport Express

Hi Guys
This is a quick post with a problem & solution.
I've been searching for ages tonight to find a solution to my problem:
'iTunes suddenly cannot connect to my Airport Express Speakers" and could not find one answer on here, only a mixture of replies all over the net.
So, just incase some people are still looking for an answer:
What I did...
1. Go to System Preferences, Network.
2. Click Advanced, on the TCP/IP tab, set "Configure IPv6" to Off.
Open up Airport Utility, go to the Music tab, set a password (I did this just for the sake of seeing whether iTunes noticed that the Airport was now password protected, then atleast you know it's talking!)
3. Open iTunes, go to preferences.
4. Click on the devices tab, untick "Look for remote speakers connected with Airplay, Allow iTunes control from Remote Speakers, Forget All Remotes.
5. Close iTunes
6. Open iTunes, retick "Look for remote speakers connected with Airplay, Allow iTunes control from Remote Speakers, Forget All Remotes.
7. Connect to remote speakers worked!

thanks Simius,
I just tried what you said to do, i had it in Automatic, but when I momenterely switched to manual the fields were all blank so I left them that way and turned on to automatic as you said and left it in auto, then tried to change itunes speaker to remote airplay and it didn t work.
so i don t know what else to do, I read alot about this in the last few days the bug seems to be related to the newest itunes upgrade and with the presence of the IP6V not turned off completely.
in the old system one could turn it off completely, now the off button is gone.
there are work around using terminal, I tried that but it doens t recognize my commands, so it didn t work either.
anybody has any idea?
thansk a lot
D.

Connect Samsung TV to AirPort Express Wi-Fi

Similar Messages

Maybe you are looking for