Connect smart TV to ONT without using router?

I have Fios TV, internet and phone. My ONT is in the basement and is run to a router 2 floors above and at the other end of the house. A smart TV, which is one floor directly above and only about 20 feet from the ONT, has poor Netflix performance using wirless internet that is at the other end of the house and a floor up. I understand that the solution to the Netflix problem is to wire the TV directly to the internet. However, this would require pulling ethernet wire from the router, down two floors and to the other end of the house and then back through the floor to the TV.
Coaxial cable connects the ONT to the router. It would be simple to connect the ONT to the TV using the ONT's eithernet port, but it is unclear if that would work given that the router has a coaxial connection.
Can you offer any solutions?

You can't connect the TV to the ethernet jack in the ONT. Your WAN connection is currently provisioned over coax (MOCA WAN). The ethernet jack in the ONT can't be used at the same time.
I would suggest getting a MOCA bridge.
http://www.amazon.com/Actiontec-Ethernet-Adapter-Service-ECB2500C/dp/B008C1JC4O/ref=sr_1_2?ie=UTF8&q...
Simply connect one side to your coax and connect the ethernet side to your TV.

Similar Messages

Can i turn off the option that enables iOS 8 to connect to my apple tv without using wifi?

I am a schoolteacher and our school uses Apple-tv to project lesson contents. We have separated the students wifi network from the teachers wifi network, so our students won't be able to use the apple-tv's and disrupt our lessons.
Since the introduction of ios8, the separated wifinetwork doesn't do the trick anymore. Students can now use every Appltv in their vicinity to project whatever image they want. This is a problem.
Can we turn off the option that enables IOS8 to connect to apple-tv without using the wifi network?
Thanks in advance.
Marco

Unless buffering a rental/prior purchase to watch it should not consume significant bandwidth when connected.
Power wise it uses 6W at most.
You can't power off from the remote but you can set it to sleep -
Press and hold Select for five seconds (or go to Settings > Sleep Now on Apple TV (2nd generation), or Settings > Standby on Apple TV (1st generation)

Connect Apple TV to MBP without a router

Hello Apple TV experts, hope you are having a good day.
My sister is out in the woods in Virginia in her 5th wheel trailer. She has a nice TV/Stereo setup but only gets over the air TV. She has movies on her MacBook Pro and wants to watch on the TV. She has no internet connection nor router.
Can she put in an Apple TV and connect the MBP directly to it without have a network router? Or would she be better off with a hard wire solution?

Newer MBPs have HDMI ports.
What ATV generation do you have? What MBP do you have (year/model)? ATVs support Airplay, so using the ATV as an Airplay sink and MBP as Airplay client is still possible.
There are display port-ot-HDMI adapters as well.
Alley_Cat has covered iTunes DRM content, but you can still play non-DRM content via Airplay and HDMI/Component (depending on ATV model).
MBPs usually have a combo analog/Digital Optical connection that can be hooked up to a stereo for sound.

Is it possible to connect labview with opc server without using NI dsc Module ?

Hellow sir,
I want to get data over labview using OPC server and i am not using any dsc module vi (Alams, print, GUI, security).I am using share variable to get data from OPC server to labview. Now i want to deploy that application to third party computer. (where there is no NI software is installed)
i am using labview 8.6 and 2009.
Many ? like....
1) what is the procedure to install that application in third party computer.
2) Do i need to use my dsc run time licence..?
waiting for your valuable feed back.
Thank you.
CLAD
Labiew programmer

Hi, When you connect to NI OPC Server by creating New I/O Server > OPC Client. You will see all registered OPC Servers running on local machine or remote machine. I used KepServerEx from Kepware and LSIS OPC Server from LG with no problems. Just make sure that the OPC server is running.
Hope it helps
Waleed El-Badry MSc.,MCPD, ISTQB Certified Tester
Assistant Lecturer
Mechatronics Department
Faculty of Engineering
Misr University for Science & Technology
Attachments:
LG.png ‏57 KB

How can I use Smart Print with IE10 without using the Bing bar.

I have used Smart Print for a long time but after upgrading to Windows 8-64bit it seems that the only way to get it now is with the Bing Bar. I like windows but I have no use for Bing.

Are you launching IE 10 from the Start screen, or from the desktop? Smart Print will only work if you launch IE 10 from the desktop.
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

HOW TO CONVERT EIGRP TO OSPF WITHOUT USING ROUTE REDISTRIBUTION?

Please help me on that...

try like this.
data : year(4),
mon(2),
day(2).
in itab declare field cbudat(8) type c.
loop at itab.
year = itab-budat(4).
mon = itab-budat+4(2).
day = itab-budat+6(2).
concatenate year mon day into itab-cbudat.
modify itab.
endloop.
now use select for all entries and check gdatu = itab-cbudat.
regards
shiba dutta

Database refresh without using RMAN duplicate

Hi All,
I am planning to refresh my test instance to a PIT using RMAN backups from PROD. I would like to know the process without connecting to PROD database and without using RMAN duplicate command.
Thanks.

imran khan wrote:
Can you please show the demo first then we will discuss on it more.. what if the folk wants to refresh it ten times then we have to change the database name ten times using NID?
>Can you please show the demo first then we will discuss on it more.. what if the folk wants to refresh it ten times then we have to change the database name ten times using NID?
1) You use nid only to change the dbid.
2) I have done this type of cloning much more than 50 times.
3) As Iordan Iotzov pointed out, in 11gR2 you can run DUPLICATE database without being connected to the PROD
Here is a sample code of how to do it assuming both file system are the same:
# -- RMAN Restore to another server
rman <<EOF2
CONNECT TARGET /;
STARTUP NOMOUNT
SET DBID 987654321;
CONNECT CATALOG rman/rman@rcvcat
RUN {
    SET UNTIL SEQUENCE=5678 THREAD=1;
    ALLOCATE CHANNEL ch0 DEVICE TYPE DISK;
    RESTORE CONTROLFILE;
ALTER DATABASE MOUNT;
RUN
SET UNTIL SEQUENCE=5678 THREAD=1;
ALLOCATE CHANNEL ch0 DEVICE TYPE DISK;
ALLOCATE CHANNEL ch1 DEVICE TYPE DISK;
ALLOCATE CHANNEL ch2 DEVICE TYPE DISK;
ALLOCATE CHANNEL ch3 DEVICE TYPE DISK;
RESTORE DATABASE;
RECOVER DATABASE;
EXIT;
EOF2:p

On iOS 6.0 how can I Airplay to AppleTV using router without internet connection.

Hello,
I do a lot of presentations. I recently updated my iPad to iOS 6.0. In the past on iOS 5 I used an iPad, AppleTV, router, and projector for presentations. Now when I connect the iOS iPad to the router it requires the router to be connected to the internet so the iPad can connect. Iam often presenting at places that do not have internet so this is an issue. Is there anyway around this? I have done some testing and it appears that the iPad has to authennticate to Apple everytime it wants to connect to the internet.

You cannot use your iPhone as a router without being connected to data.
That is essentially what I said above. When streaming local content you won't incur any data but you can't use the feature while in airplane mode.
However; you can use an airport express (2nd generation) as a router without being conected to the internet.
Yes, An Airport Express is a router, which is what I recommended initially as it is a much better solution, glad it's all worked out.

Use printer connected to PowerBook (w/AirPort) from a PC without a router?

Thanks in advance for any help, and forgive me if this has been answered. A search turned up no satisfactory results.
Is it possible to print wirelessly to a printer that is connected to my AirPort-equipped PowerBook from a PC without a router in the mix?
Basically, can the PowerBook act as an access point (is that the correct term?) so that I can connect to it wirelessly from a PC and use its USB printer? Neither machine will be connected to the Internet, and a router will not be used.

Hi,
If I understand this correctly, you wish to set up an ad hoc (wireless peer-to-peer) network between a PC and a Mac. A USB printer will be connected to the Mac. The Mac is running Mac OS. The printer is to be shared.
The level of complication is high, since two platforms are involved, since it is a USB local printer (not a network printer), and since neither a print server nor a router (base station) will be used.
It would probably not be a bad idea to have a look at, or post a question in, the Windows Compatibility forum or one of the AirPort fora instead. Also, this web page might be of interest regarding general setup issues.
Additionally, a remote control application could possibly offer a solution.
Jan

Can i setup a wifi router with my IPad2 without using a computer ?

Can i setup a wifi router with my IPad2 without using a computer ?

This is going to depend on what wireless router got get. Some want to do all administration functions via a ethernet cable connection for security reasons.
Once the router is configured, you will no longer need a computer.
Try looking for a router that configures through a web browser & allows administration from a wifi connections.
I think the easiest thing will be to have a friend come over & configure with a laptop. I believe that you can configure the router without have a broadband connection. You could configure it at a friends house. Might not want to connect to the friends broadband so not to confuse your friends broadband. ( this is only a worry if the router also includes the broadband model. Just a wireless router without a modem is not worry ).
Robert

How to share iMac WiFi Internet connection without a router

I would like to know if I can link my iPod Touch (new one) to my iMac so that share my internet connection via wi-fi via Airport at home without a router.
I have tried to like my ipod touch to iMac by turning airport and setting up a new network, the ipod touch is able to pick up the wireless signal of my iMac ant the Airport status bar shows an arrow out which mean that airport is sending signal out but for some reason when I try to use Safari or Mail in get the following error message "cannot Open Page Page, Safari cannot open the page because it is not connected to the internet"
Also when when scanning for wireless signal with my iMac I am able to pickup my neighbours wireless signal while my iPod Touch is only able to pickup my iMac airport wireless signal.
What I am missing ?

1. Open System Preferences
2. Go to 'Sharing'
3. Click on 'Internet Sharing' (leave the box unchecked for now).
4. From 'Share your connection from' choose 'Built-in Ethernet'
5. From 'To computers using' check the 'Airport' box
6. Open 'AirPort Options' (bottom right), name the network. (Once it all works, go back and assign a password).
7. Now, check 'Internet Sharing' box and turn on AirPort. The AirPort sign on the iMac menu should turn into an arrow.

TS4006 i am having problems connecting to wifi at home , i want to do a master reset but cant save to icloud without using wifi ?? any ideas ??

i am having problems connecting to wifi at home , i want to do a master reset but cant save to icloud without using wifi ?? any ideas ??

If you can't perform an iCloud backup (which requires wifi), back up to your computer with iTunes. Connect your phone to your computer, open iTunes, click on the name of your phone in iTunes, go to the Summary tab of your iTunes sync settings and click Back Up Now.
To troubleshoot your wifi, try unplugging your wireless router for 15 seconds, the plug it back in. Then go to Settings>General>Reset and tap Reset Network Settings (note: this erases passwords for previously joined networks). Then rejoin your wifi and see if it works properly now.

Connecting Apple TV device and Macbook Air (early version) without using a TV

Hei,
I am trying to set up my home cinema using a projector and not a TV. I have a Macbook Air early 2011 version (the one where you can only stream directly from Itunes and use a third party device to play the rest) that I am trying to connect this device to the apple tv device - but as said without using a tv. I have speakers with a console where you can run an optical digital cable from the console to the Apple TV (as this will then give me sorround sound as opposed to the airport express that has not got this option). However my computer and projector is on the other side of the room so I want to be able to wirelessly connect to my speakers via my computer.
All set up guides with the apple tv involves connecting the apple tv device and a TV with an HDMI cable. As I am not using a TV and I am not connecting the apple tv device and my projector only aiming to stream sound to the speakers to the Apple TV device I am at a loss in terms of what I need to do. Can anybody help?
Thank you!
Lene

Airplay requires both devices to be connected to the same network (wired or wireless).

How to configure one dsl connection and one public ip in cisco router and map to one interface for using exchange server

how to configure one dsl connection and one public ip in cisco router and map to one interface for using exchange server

Hi ,
Have you got any additional public IP Address from your service provider , If yes on router you can have static route for those additional IP Address pointing to your ASA outside interface .
Accordingly you can configure NAT
HTH
Sandy .

What is the direct connect method for transfering photos from my macbook pro to my iphone without using iTunes syncronization? (iow: a simple photo copy from mac to iphone?)

I feel like I should know the answer to this. I can't believe it is a hard question.
What is the direct connect method for transfering photos from my macbook pro to my iphone without using iTunes syncronization? (iow: a simple photo copy from mac to iphone?)
Easy? Right?
Just plug my iphone in to a mac and copy a photo from the mac to my iphone.
I don't have internet access - I can't email it, or mobileme it, or dropbox it.

iTunes. Other than that there is no direct method. However, do try the iPhone forums.

Connect smart TV to ONT without using router?

Similar Messages

Maybe you are looking for