Connect to 2 Networks?

How do I utilize my internal network (std 192.168.x.x config) with my corporate network (which uses a 172.16.x.x config)? Both are set up to use 255.255.255.0 subnet.
I configured the router with a subnet of 255.255.255.128 but I don't know what to do at that point. I show 2 network addresses and 2 subnets on IPCONFIG but I cannot reach anything on the local (.128) subnet. If I disconnect from the corporate (.0) network I can then reach the local internal network just fine.
I know someone can help me out there!
Thanks!
Brett

Hi… Do you have 2 different IP address for 2 different networks on same PC? Do you have 2 LAN cards on that PC?
I think you mean to say you have a local network which has 192.168.x.x and you are connecting to a remote network 172.16.x.x through PPTP (windows XP VPN) or RDP or VPN. Now since you get 2 IP addresses I think you are using PPTP connection to connect to remote network. If that’s correct, then in PPTP your pc can access the resource of your remote network but not of local and that’s why you receive that second IP address.
However this is my assumption, if I am mistaken please let me know your network setup, so that I would be able to provide with a correct solution.

Similar Messages

How can I see what equipment is connected to my network?

I use a Time Capsule for my home network. Is there a way for me to see each device that is connected to my network at any given time?
There has been an unknown device continue to show up in finder under "shared".... I've reset my network password a couple times and the device continues to show up. (Its identified as "npica53cf")
Thank you

Its identified as "npica53cf"
I think HP has used default network printer hostnames in the format: npi + last 6 digits of the device's MAC address (e.g. "ca53cf").

Apple TV 1st Gen can no longer connect to wireless networks

My Apple TV (1st Gen) has recently lost the ability to connect to either of our wireless networks at home. I rean the diagnostics at the reset screen and the Apple TV says it is performing normally. In the settings, whenever I attempt to connect to a wireless network, I am now only offered "Other..." as a choice. Proceeding to the next screen, I enter the name of the network closest to the Apple TV -- an Airport Extreme set up for 5 GHz that this Apple TV connected with daily up until 2 days ago. The Airport base station is perfoming normally, as my MacBook Pro can see it and establish a network connection without any difficulty. The issue is limited to the Apple TV. I did a Factory Restore, and now when I go to Wireless Network > "Other..." > Enter the name of the wireless network" the resuit is always the same, and error message stating: "There was a problem connecting to the network. Check your settings and try again. (-4)".
This message comes up almost immediately, without requesting a WiFi password -- suggesting to me that this Apple TV has lost the ability to connect to ANY wireless network due to a hardware failure.
Q: Has anyone else in the Support Community had a similar experience with their 1st Gen Apple TV, and if so, did you find a solution to it?
Note: When I first noticed the connction to this Apple TV had gone stale (greyed out in the iTunes Airplay Speakers list), and prior to doing the Factory Restore, I could play back iTunes content stored on the hard drive, but could not connect to the local wireless networks. I noticed that the Apple TV was running very hot -- it has alwasy run pretty hot to the touch.
If this Apple TV has died, I will get a 3rd Gen Apple TV, but wiill then have to work through the HDMI to Composite video + Audio issues, as this Apple TV is connected to our older (non-HDMI) TV.

Follow-up: Able to connect with ethernet cable, downloaded software updates, connected to iTunes, and synchec content.
Next, disconnected the ethernet cable. ATV1 froze and was restarted using the Menu + ( - ) combo on the remote. Re-ran diagnostics yeilds: Apple TV is working fine.
Restarted, then went to configure the Wirelss settings. Apple TV once again does not show either of the two wireless networks. Selecting "Other..." and entering the SSID yields the same immediate response:
"There was a problem connecting to the network. Check your settings and try again. (-4)"
No change on the wireless front :-( Bummer.
Looks like an ethernet connection is the only option left to continue using this Apple TV 1st Gen.
Thanks for your help. -- Paul

Can no longer connect to my network and 'forget network' option has disappeared??

Can no longer connect to my network and "forget network" option has disappeared??? (Ipod touch 5th generation). This happened on both my children's ipods. We have reset network settings but it doesn't help.

JEM24 , your suggestion is included in:
- iOS: Troubleshooting Wi-Fi networks and connections
Turn your Wi-Fi router off and on2. If your ISP also provides cable or phone service, check with them before attempting this step to avoid interruption of service.
JEM24 wrote:
Sorry Mindi, also have your tried rebooting your router? That's all. Try that before you attempt to Restore. Cheers.

Iphone 4 does not stay connected to my network

Since upgrading to 6.1, my iPhone 4 does not stay connected to my network. I have to input my password each time I leave my house. My other devices stay connected, so the issue is with the upgrade. Has anyone found a way to keep their IPhone connected to their network? Thanks.

I don't have another phone to try. I took out the sim to check for deffects but it looked fine. Cleaned the sim card with alcohol and cleaned the aim compartment. Phone didn't loose Internet connection all day yesterday, but this morning went to check emails and wouldn't update until I turned airplane mode on then off again.

My deskjet 3050 j610a isn't connecting to the network in my house.

my deskjet 3050 j610a isn't connecting to the network in my house. I've tried about everything and it still not connecting. It's a wireless printer and it's not connecting to either my desktop or my laptop. what do I do now?

Select  ▹ System Preferences ▹ Network. The WiFi connection should be at the top of the list on the left, and selected. Click the button labeled Assist me and select Assistant. Follow the prompts. How far do you get?

My mac air does not recognize my printer connected to a network

Is usb to lightening the correct connection to see the printer

Hello there, Appletreflie.
The following Knowledge Base article should have some practical information for you to help setup your printer:
OS X Mountain Lion: Set up a printer
http://support.apple.com/kb/PH11145
Specifically:
Add a network printer to your list of printers
You can connect to printers on your local network that use Bonjour, IP, and Open Directory, as well as shared printers and printers connected to a Time Capsule or AirPort base station.
Be sure to follow any instructions from your network administrator.
If the printer isn’t connected to your network, follow the instructions that came with the printer to unpack it, install ink or toner, add paper, and connect it to your network.If you’re connecting a printer to a Time Capsule or AirPort base station’s USB port, see this help topic:Set up a printer connected to a Time Capsule or AirPort base station
Choose Apple menu > Software Update to make sure OS X has the latest information about printer software it can download from Apple.Usually you shouldn’t install software that came with the printer on your Mac. OS X downloads the latest printer software automatically.
Open a document to print, and then choose File > Print.
Open the Printer pop-up menu and choose your printer in the Nearby Printers section of the menu.
If you don’t see your printer, choose Add Printer from the Printer pop-up menu.A dialog appears listing any Bonjour, IP, shared, and Open Directory printers on your local network. It may take a minute or two for your printer to appear.If you’re asked for an administrator name and password
Select your printer when it appears in the list, and then click Add.OS X automatically uses AirPrint if your printer supports it, or it selects printer software (also called a printer driver) and downloads it from Apple if necessary.
If you don’t see your printer in the list, do one of the following:
For an IP printer, click IP in the toolbar and enter the printer’s information. For more information, see this help topic:Set up an IP printer
For a shared Windows printer, click Windows in the toolbar and enter the printer’s information. For more information, see this help topic:Connect to a printer shared by a Windows computer
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro D.

My Iphone 5 won't connect to a network or wifi

My Iphone 5 won't connect to a network or wifi, I just got the phone less then a month ago.....It is driving me nuts and I don't know how to fix it!I

Have you read through the user guide and taken basic troubleshooting steps? What have you done so far to troubleshoot?

Have an airplay enabled AV Receiver - how do i set up Airplay I have a Yamaha RX-V673 which is Airplay enabled, but i can't get Airplay to work either on my Mac book or my iphone. The receiver is connected to my network and i can control it using the

have an airplay enabled AV Receiver - how do i set up Airplay
I have a Yamaha RX-V673 which is Airplay enabled, but i can't get Airplay to work either on my Mac book or my iphone. The receiver is connected to my network and i can control it using the iphone App and via the web browser option.
Do I need Apple TV or to change some settings somewhere?
Any help would be greatly appreciated

You are making some progress with setup of wireless network. Apparently there is reliability problem with the wireless connection. Perhaps you want to refer to following Apple support documents and start tweaking parameters in the router to improve the reliability. I used to have third-party routers such as Belkin and Netgear but switched to Apple Airport routers (Time Capsule then Airport Extreme for now) because of incompatibility issues whenever Apple upgrade Mac OS X. But since Apple develops Airplay protocol as alternative to Bluetooth for wireless audio/video streaming (with much better bandwidth) and must be deployed in any wireless network, there is no reason third-party routers not working for Airplay protocol.
About AirPlay Mirroring in OS X Mountain Lion:
http://support.apple.com/kb/HT5404
iOS: Recommended settings for Wi-Fi routers and access points:
http://support.apple.com/kb/HT4199
Troubleshooting AirPlay and AirPlay Mirroring:
http://support.apple.com/kb/TS4215
Good luck in setting up 802.11 wirelesss network.

I am having trouble connecting to my network all of a sudden. It is not an issue with the service/router. I keep getting kicked off and getting a ! in my airport... anyone know what's up with this?

I am having trouble connecting to my network all of a sudden. I am able to connect to other networks but not my own. It is not an issue with the service/router because other devices connect fine. I keep getting kicked off and getting a ! in my airport. Last time it happended I called apple and the suggested I wipe my HD and reinstall everything. I did and it did not work. One day I turned my laptop on and it connected no problem. Now it has kicked me off again. I tried resetting my IP address but that does not work either! Has anyone had this problem?

Try this:
Apple menu / System Preferences / Network.
Click Location: and select Edit Locations..
Click + (plus sign), and enter a name for the new location - anything will do.
Apply this.

New Macbook Pro. wont connect to wireless network once it has had a update

hi
bought a new macbook pro last week, when you first start it up it connects fine to a wireless network, but once the software update is compltete it says that there is an error trying to jion network. there is already a powerbook g4 connected to the network and a pc. i have re installed tiger and it can connect fine until the software update has restarted the mac and the same error is back again. do i re install it again and never update it or is there a simple way to correct the fault

My girlfriends New Macbook Pro is doing the same thing. I does connect to non-secure wireless connections such as at the airport but doesn't connect to her home wireless connection that is run by an SBC DSL 2WIRE gateway. I can connect fine on her old IBM laptop that I am on right now through this network wirelessly.
There has to be a fix for this?

Error: there is a problem connection to the GPRS service in your registered home network, error trying to make data connection. this may be casued by a voice call, a wired activesync connection or inncorrect network setting

like 2 weeks ago i called in to att to see how much is the data plan and it would end up costing $30.
so i was like screw that. well they figured that i got a new phone replacing the LG shine. so they asked
for to call this number so they can recieve data which would updated the system that i have a plam treo 750.
ever since this conflict i can't send picture messages. i get that problem. everytime i attempt to send a picture
i recieve this.
- there is a problem connection to the GPRS service in your registered home network.
- then i get a test that says error trying to make data connection. this may be casued by a voice call,
a wired activesync connection or inncorrect network setting.
please someone help me.
btw. hard reset and soft reset did not work for me.
Post relates to: Treo 750 (AT&T)

problem fix, i had to call in. customer serivce. and when i called to ask about the plan. they blocked it. so i had to unblock my internet.
Post relates to: Treo 750 (AT&T)

S860 and X2, Google not connecting on mobile network.

I live in Sweden. Had my S860 for 3 years and it has been working fine but some months ago it was not connecting on mobile network with crome and play store. Restart and it could work for some time the it was gone again. At the same time Hotspot, skype and OS update is working fine. Got a new sim card i november but it did not help. This was going more and more bad and finally it did not work at all. Tried to reverse OS a few steps back and still not working. So i tought that it was something to do with hardware. Now i bought a Vibe X2. Away from sweden for the moment (Saudi Arabia) but this one does the same when I try to connect. OS update working but Crome says ssl error and Play Store just wont connect. Saw some forums said it might be time and date that was wrong so i tried to change to local format but it was the same. My S860 i was waiting for 6 month before i could buy it (not for sale in Sweden) in Saudi. Haas been very pleased with it so now when it has been messing with me i had no problem to buy a new Lenovo phone. This time just waiting 3 month before i could buy it in Saudi. Hope this is something I can get some help to solve. /Nils

Hi Ragge
Can you tell me your firmware build number(for the S820 and Vibe x2) and Baseband version(for the S820)?Settings->About phone....
''Had my S860 for 3 years and it has been working fine.....Sorry, checked and it is a S820 i have.''
The S820 has been relesed in May 2013.
''Tried to reverse OS a few steps back...''
How did you do that?.
Can you install THIS ->Open the app->MTK Settings->Telephony/BandMode->SIM 1(Do the same for SIM2) and make a screenshot(Power&Volume-) ->post the screenshot here.Thanks
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as ''ACCEPT AS SOLUTION"!
Unsolicited PM's will not be answered! ....Please post your question/s in the appropriate forum board.
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Upgrading to xcode and can't connect to the network

Hi! I use a C++ library in my application which connects to the network (I suppose it uses sockets). I've been using it for months and I was using xcode 3.2.4. Now, I just had the great idea of upgrading to xcode 3.2.5, and I found out my application was crashing with the error:
If you are encountering this problem running a simulator binary within gdb, make sure you 'set start-with-shell off' first. 3.2.5
Ok, couldn't solve it, so went back to 3.2.4, as suggested somewhere. The application is not crashing anymore, but now the library can't connect anymore to the network. Tried to rebuild it (I didn't write the library but I have the sources) and use the new library, but nothing. Still the library can't connect to the network. I tried with every simulator.
Any idea what there could be wrong and how I may be able to solve this? Can I somehow delete manually everything related to xcode and the simulator and try to start all over again?
Thanks!

I've been able to temporarily solve this problem by removing the entire Development directory and installing again xcode 3.2.4. Even with xcode 3.2.4 however, the same happened, and I had to do this procedure again. Now it seems to be working correctly, but it seems something very strange has happened. Hasn't anyone experienced anything similar?
Thanks!

Cannot connect to 4G network after update to OS 10.3.1

Have a Q10 through Sprint and after updating to OS 10.3.1 from the Blackberry site, phone will now only connect to 3G network despite availablity of 4G network. Phone used to connect to 4G network with OS 10.2,

I do have same problem, i'm unable to connect to even 3G network and it connect to 2G network only when there is full network
My page on: App World
Check out my Apps 1). QFileExplorer 2). My ABCD
System Explorer APPID: 35601892

When I connect imac to network via airport all devices on the network lose internet connectivity

Every device stays connected to the network but the internet stops working. Usually the network will continue to function normally for about five minutes when the imac connects, but then every device loses internet access via the network, NOT just the imac. As soon as I turn off the imac's airport they get internet connectivity back. A wired network connection to the imac seems to work OK.
The airport is configured as "Using DHCP"
Mac OS X 10.6.8
As far as I know, no changes have been made to the computer recently (but it is not my machine and the owner isn't here atm)
I found one other resource with the same problem here:
http://www.mac-forums.com/forums/internet-networking-wireless/183185-turning-my- macbook-airport-breaks-internet-connection-entire-network.html
but the solution didn't work. When I deleted the three files mentioned in the solution in that thread, my problem is not solved.
If you have any ideas or need more information I would love to hear from you.
Thanks guys.

Yes it is possible that the two machines are creating a Computer-to-Computer network and are not going through the Express.
To delete the Alias you may need to login with the Admin User.
Will
1GHz G4, 15" PowerBook, Airport Network, 1G iPod Mini Mac OS X (10.4.5) Updated - Get Started with iWeb (WillG4PB.com)

Connect to 2 Networks?

Similar Messages

Maybe you are looking for