Connect to iTunes required after every power off of Ipad 64GB wifi
My Ipad 64GB wifi model continually prompts to "connect to iTunes" every time I power off and power back on. This is extremely frustrating and the Apple Customer Care has asked that I return my iPad. I would rather find a solution since I am working Iraq and my Ipad is my e-book reader (in place of a Kindle. Steps taken thus far:
Reset iPad (Erase All Content and Settings)
Reset Network settings
Reset All Settings (content not erased)
I've read that this problem sometimes occurs with some third-party applications installed (like Jailbird) . I do not have any of those applications installed. If anyone can offer a solution I would greatly appreciate it.
Danielle
Since you erased all content and reinstalled the OS and this still happens, sounds like a hardware failure. You need to take the iPad back to an Apple store for an exchange.
Similar Messages
-
please help me how to get out of the connect to i tunes screen which came after trying to update software of ipad 3 through software update in the ipad i t is not coming out of the connect to itunes scree neither being able to switch it off
Try and force your iPad into Recovery Mode
1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
Note: Data will be lost. You may have to repeat the above many times. -
Anyone having Bluetooth syncing issues w VW Tiquan11... and iPhone4? Essentially the pairing craps out every other time when you connect to the cars bluetooth. Requires rebooting iPhone, power off/on and then connects..
Many people are finding their Iphone 4S drops connection with their VW (Passat etc) integrated bluetooth hands free system after working fine for 5, 10, 20 minutes. The only way to reconnect is to switch the car off or turn the Iphone bluetooth off & back on.
This is a dangerous fault and it appears that both Apple & VW have no solution (or are ignoring as they have already sold you a phone & a car).
iPhone 4S, iOS 5.1.1, VW bluetooth -
While doing a non-iTunes upgrade to 8.02 my iPad froze on the apple screen. After hours of waiting I forced a power off. Froze in same place. Tried attaching to iTunes on PC from power off. Freezing in same place. Any ideas on how to get past this so that I can at least run a restore?
I Don't know that recovery mode would work, but did you try it?
If you can't update or restore your iPhone, iPad, or iPod touch
IF that fails, have you considered erasing the device using Find my iPhone in iCloud.com? I'm not sure what good that would do either of the iPad continues to freeze, but if nothing else is working ..... -
my phone is stuck on the connect to itunes screen after trying to recover it to a backup.what should i do???
PLEASE HELP!!!Hold down the Home and Power button to shut off the iPhone. Keep it disconnected from the computer. Then, hold down the Home for 20 seconds. Connect it to the computer while continuing to hold down the Home button. Wait for iTunes to say your iPhone is in Recovery mode. Then, restore.
-
My ipod touch is frozen on the connect to itune screen after an update
My ipod touch is frozen on the connect to itune screen after an update. What do I do to solve the problem. The power on-off button does not permit me to reboot the system.
The BOLD may be necessary
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
Why can't I connect to Itunes store, after updating my ipad to OS 6?
Why can't I connect to Itunes store, after updating mt Ipad to Os 6?
Saw this on another post.
Applecare Senior Advisor Txx Bxxx (I have his contact info in an email he just sent) just confirmed with me that the problem people are having with the App Store not loading is an apple issue with there servers, ITS NOT YOUR IPAD so don't go restoring it! It's not happening to everyone however but they are looking into it, its really hit or miss.
In the meantime ...........
The Complete Guide to Using the iTunes Store
http://www.ilounge.com/index.php/articles/comments/the-complete-guide-to-using-t he-itunes-store/
Can't connect to the iTunes Store
http://support.apple.com/kb/TS1368
iTunes: Advanced iTunes Store troubleshooting
http://support.apple.com/kb/TS3297
Best Fixes for ‘Cannot Connect to iTunes Store’ Errors
http://ipadinsight.com/ipad-tips-tricks/best-fixes-for-cannot-connect-to-itunes- store-errors/
Try this first - Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.
This works for some users. Not sure why.
Go to Settings>General>Date and Time> Set Automatically>Off. Set the date ahead by about a year.Then see if you can connect to the store.
Cheers, Tom -
I tried to use lightning to usb camera adapter but every time I plug it into my ipad mine it give cannot use device. the connected usb device requires too much power. how could I use this attachment.
Or use the camera's SD card instead.
Cheers, Tom -
Canon 60D does not resume after auto power off
My Canon 60D does not resume after auto power off. It shows the empty battery icon when I press the shutter button, even the battey is fully charged. If I remove the battery and insert back it will resume to work. Any one had the same experience and know how to resolve it?
The power switch is actually a "software" switch. It's not like a light switch in that it doesn't actually provide or deprive the camera of power... only removing the battery will deprive the camera of power. This is why it doesn't actually just go dark when you switch off power... instead you'll usually see it perform a sensor clean cycle and then power down. The camera is technically in a kind of "sleep" mode monitoring the switch. If a Canon camera ever seems to lock up and ignore all input, the battery should be temporarily removed to "reboot" the camera. There is no "setting" in a camera that can configure it to ignore buttons. Although... if the camera is in an automatic mode, some input is deliberately ignored to make it easier to use the camera. Put the mode dial in a "creative zone" mode (P, Tv, Av, or M) and all buttons and menus should be accessible. You might try connecting the camera via USB cable to your computer and then attempt to control the camera via the Canon EOS Utility to see if that works. If the camera responds fine to the computer control, then likely the camera's main board and circuits are working fine and it may just be a wiring problem -- as if some cable simply isn't getting a very solid connection. If this is a wiring issue, you are probably better off sending it in for service.
-
Error appeared when I connected my camera to iPad I used a camera connection device error cannot use device t he connected USB device requires too much power
Thanking you
Wendy BanksSome cameras are designed to use the power suppled via USB when they're plugged into another device, usually a PC or laptop. The iPad does not supply sufficient power for a camera. The iPad Camera kit allows for either a camera to be plugged in only for the transfer of photos, not as a power sourse, or the removal of the SD Card from a camera so it can transfer photos as an alternative.
-
after my daughter tried many password to unlock my ipad, it became disabled, everytime i open it, it says "ipad is disabled, connect to itune, but after i connect it to ituned, it can not open due to passcode protected, how can i open my ipad?
Hi perrygirl!
I have an article here that can help you resolve this situation:
iOS: Unable to update or restore
http://support.apple.com/kb/HT1808
If your computer is still not recognizing the device after following those steps, you may need to troubleshooting following the steps in this article:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/ts1538
Thanks for coming to the Apple Support Communities!
Regards,
Braden -
i am unable to restore my iphone 4s " screen showing USB cable arrow showing to connect to iTunes" when i connect to itunes it after asking restore (step 3 without going to step 4) starts updating itunes with no effect to screen which is still showing usb and itunes symbols
See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once...
Be sure to Follow ALL the Steps...
But... if the Device has been Modified... this will Not necessarily work. -
My iPhone 3gs got an update today ios 6.1.6 but when i press install update my phone shutdown and shows connect to itunes display, after i connect to itunes it shows unknown erro (306).....whats is happening and what should i do ?
Take a look at this post: https://discussions.apple.com/thread/5036467?tstart=0
iTunes: Advanced iTunes Store troubleshooting
http://support.apple.com/kb/TS3297
iTunes Store loads partially or returns "Error 306" or "Error 10054"
Proxies, parental control settings and software, security or filtering software, or a bad iTunes Store cache can cause this.
To address proxies, Remove Internet Options proxy settings and connect to the Internet without a proxy.
To reset iTunes Store cache:
In iTunes, choose iTunes > Preferences (Mac) or Edit > Preferences(PC).
Click the Advanced tab.
Click the "Reset cache" button.
Click OK and see if the issue is resolved.
Adjust Parental Controls in iTunes:
Open iTunes.
Access iTunes preferences:
On a Mac: From the iTunes menu, choose Preferences.
On a Windows PC: From the Edit menu, choose Preferences.
Click the Parental Controls tab.
Remove restrictions on Parental Controls.
For more information on parental controls or content filtering software, seeiTunes 10.5 for Windows: May see performance issues and blank iTunes Store.
For more information on other security software, see iTunes: Troubleshooting security software issues. -
I tried restoring iPad1 to prepare it to sell, encountered error during the restore. iTunes dispalyed a message that there had been an error. My iPad1 is just showing the image to connect to iTunes, even after i try restarting the iPad1. I've also restarted my PC and iTunes will not recognize the iPad1.
iTunes is and will recognize my new iPad3 just fine.
How do I get my iPad1 to come back to life?
Thanks!No luck. The article says to press and hold the home button, then plug in the usb cable. When i do that, I still just have the connect to itunes image on the iPad, and iTunes is not recognizing the iPad.
-
After updating my ipad to ios7 it is on recovery mode. Then I tried to reboot it and it shows an image to connect to iTunes. I tried to connect to iTunes and restore it but it says ipad could not be restored and an error occurred. What can I do now???
http://support.apple.com/kb/TS3694#error3194
This might help. Good luck, I really hope this all works out. :-)
Maybe you are looking for
-
Please Help - Only Some Port Forwards Working
Hi all, I have the most annoying issue with a Cisco 887VA-K9 port forwarding. Some port work while other don’t and I just can’t see why, however I suspect it is a zone based firewall (ZBF) issue. Port forwards on the follow ports all work fine: Exter
-
Possible Audigy 2 ZS popping fix
I'm not sure if something like this has already been posted, but I'll chime in my 2 cents anyways. I installed my Audigy?2 ZS card again last night after being annoyed for months with it and using my onboard audio because of the popping and crackling
-
Lost my phone numbers, how do i get them back with a backup?
how do you work the back up so i can get my notes and phone numbers back?
-
Latest Software of iOS 7.0.3 Wont install even when I have deleted all applications.I don't want to buy more memory as I have already done.
-
Windows 7 64 Bit. I had adobe air installed for Leauge of Legends. It stopped working and I tried fixing the game client. Uninstalled and then re-installed the game but when I try to re-install adobe air, the installer crashes without showing any win