Connect to VPN but can't ping past inside interface

Hello,
I've been working on this issue for a few days with no success. We're setting up a new Cisco ASA 5515 in our environment and are trying to get a simple IPSec VPN setup on it for remote access. After some initial problems, we've gotten it to where the VPN tunnel authenticates the user and connects as it should, however we cannot ping into our LAN. We are able to ping as far as the firewall's inside interface. I've tried other types of traffic too and nothing gets through. I've checked the routes listed on the VPN client while we're connected and they look correct - the client also shows both sent and received bytes when we connect using TCP port 10000, but no Received bytes when we connect using UDP 4500. We are trying to do split tunneling, and that seems to be setup correctly because I can still surf while the VPN is connected.
Below is our running config. Please excuse any messyness in the config as there are a couple of us working on it and we've been trying a whole bunch of different settings throughout the troubleshooting process. I will also note that we're using ASDM as our primary method of configuring the unit, so any suggestions that could be made with that in mind would be most helpful. Thanks!
ASA-01# sh run
: Saved
ASA Version 8.6(1)2
hostname ASA-01
domain-name domain.org
enable password **** encrypted
passwd **** encrypted
names
interface GigabitEthernet0/0
speed 100
duplex full
nameif inside
security-level 100
ip address 10.2.0.1 255.255.0.0
interface GigabitEthernet0/1
description Primary WAN Interface
nameif outside
security-level 0
ip address 76.232.211.169 255.255.255.192
interface GigabitEthernet0/2
shutdown
<--- More --->
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
shutdown
no nameif
no security-level
no ip address
interface Management0/0
speed 100
<--- More --->
duplex full
shutdown
nameif management
security-level 100
ip address 10.4.0.1 255.255.0.0
ftp mode passive
clock timezone MST -7
clock summer-time MDT recurring
dns domain-lookup inside
dns server-group DefaultDNS
name-server 10.2.11.6
domain-name domain.org
dns server-group sub
name-server 10.2.11.121
name-server 10.2.11.138
domain-name sub.domain.net
same-security-traffic permit intra-interface
object network 76.232.211.132
host 76.232.211.132
object network 10.2.11.138
host 10.2.11.138
object network 10.2.11.11
host 10.2.11.11
<--- More --->
object service DB91955443
service tcp destination eq 55443
object service 113309
service tcp destination range 3309 8088
object service 11443
service tcp destination eq https
object service 1160001
service tcp destination range 60001 60008
object network LAN
subnet 10.2.0.0 255.255.0.0
object network WAN_PAT
host 76.232.211.170
object network Test
host 76.232.211.169
description test
object network NETWORK_OBJ_10.2.0.0_16
subnet 10.2.0.0 255.255.0.0
object network NETWORK_OBJ_10.2.250.0_24
subnet 10.2.250.0 255.255.255.0
object network VPN_In
subnet 10.3.0.0 255.255.0.0
description VPN User Network
object-group service 11
service-object object 113309
<--- More --->
service-object object 11443
service-object object 1160001
object-group service IPSEC_VPN udp
port-object eq 4500
port-object eq isakmp
access-list outside_access_in extended permit icmp object VPN_In 10.2.0.0 255.255.0.0 traceroute log disable
access-list outside_access_in extended permit object-group 11 object 76.232.211.132 interface outside
access-list outside_access_in extended permit object DB91955443 any interface outside
access-list outside_access_in extended permit udp any object Test object-group IPSEC_VPN inactive
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended deny ip any any
access-list inside_access_in extended permit ip any any log disable
access-list inside_access_in extended permit icmp any any echo-reply log disable
access-list inside_access_in extended permit ip object VPN_In 10.2.0.0 255.255.0.0 log disable
access-list domain_splitTunnelAcl standard permit 10.2.0.0 255.255.0.0
access-list domain_splitTunnelAcl standard permit 10.3.0.0 255.255.0.0
access-list vpn_access_in extended permit ip any any
pager lines 24
logging enable
logging asdm informational
mtu management 1500
mtu inside 1500
mtu outside 1500
ip local pool VPNUsers 10.3.0.1-10.3.0.254 mask 255.255.0.0
<--- More --->
no failover
icmp unreachable rate-limit 1 burst-size 1
icmp permit any management
icmp permit any inside
icmp permit any outside
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic any interface
nat (inside,outside) source dynamic any WAN_PAT inactive
nat (outside,outside) source static 76.232.211.132 76.232.211.132 destination static interface 10.2.11.11 service 113309 113309
nat (outside,outside) source static 76.232.211.132 76.232.211.132 destination static interface 10.2.11.11 service 11443 11443
nat (outside,outside) source static 76.232.211.132 76.232.211.132 destination static interface 10.2.11.11 service 1160001 1160001
nat (outside,outside) source static any any destination static interface 10.2.11.138 service DB91955443 DB91955443
nat (inside,outside) source static NETWORK_OBJ_10.2.0.0_16 NETWORK_OBJ_10.2.0.0_16 destination static NETWORK_OBJ_10.2.250.0_24 NETWORK_OBJ_10.2.250.0_24 no-proxy-arp route-lookup
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 76.232.211.129 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
<--- More --->
dynamic-access-policy-record DfltAccessPolicy
aaa-server ActiveDirectory protocol nt
aaa-server ActiveDirectory (inside) host 10.2.11.121
nt-auth-domain-controller sub.domain.net
aaa-server ActiveDirectory (inside) host 10.2.11.138
nt-auth-domain-controller sub.domain.net
user-identity default-domain LOCAL
eou allow none
http server enable
http 10.4.0.0 255.255.255.0 management
http 10.2.0.0 255.255.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
no sysopt connection permit-vpn
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
<--- More --->
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto ca trustpoint ASDM_TrustPoint0
enrollment self
<--- More --->
subject-name CN=ASA-01
crl configure
crypto ca certificate chain ASDM_TrustPoint0
certificate a6c98751
    308201f1 3082015a a0030201 020204a6 c9875130 0d06092a 864886f7 0d010105
    0500303d 31153013 06035504 03130c43 5248442d 4d432d46 57303131 24302206
    092a8648 86f70d01 09021615 43524844 2d4d432d 46573031 2e637268 642e6f72
    67301e17 0d313330 35303730 32353232 325a170d 32333035 30353032 35323232
    5a303d31 15301306 03550403 130c4352 48442d4d 432d4657 30313124 30220609
    2a864886 f70d0109 02161543 5248442d 4d432d46 5730312e 63726864 2e6f7267
    30819f30 0d06092a 864886f7 0d010101 05000381 8d003081 89028181 00c23d5f
    acbf2b3f 9fe6e3c9 1866c344 07b6ee49 f6f31798 0b87a38b 890f70e2 c28cc1d5
    fd1b4e80 7fa25483 09e79459 6bf92155 c55240b4 93eeb4eb af3f8aec 8906ef48
    140c57bb 5ca4471f 275c1932 7e90976f f0dfe8a3 04a7861f cce7a320 7267df2e
    61f9b6b8 22bb70ac d9cedb73 3cf9747b c2636892 48b35385 a94bfae5 fd020301
    0001300d 06092a86 4886f70d 01010505 00038181 003c7e16 be4aff40 8fe69a31
    acf31808 680e44eb 8ede9094 f9a4a147 0ae18cdc 000dc07f c1da1af4 a2d964ed
    288689ee 95179ad0 90728324 9803248d b9d10641 01897453 fe7fafcd 34dee13a
    92798615 4acb1f27 14fdb346 ab3eb825 04f23791 81d08fa2 b54c6a47 aedd9694
    1c9fbcb4 455fd5ce 420298aa 9333737c 19f0e715 50
quit
crypto isakmp identity address
crypto isakmp nat-traversal 30
crypto ikev2 policy 1
<--- More --->
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
<--- More --->
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev2 remote-access trustpoint ASDM_TrustPoint0
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
<--- More --->
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
<--- More --->
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
<--- More --->
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
<--- More --->
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
management-access inside
dhcpd dns 10.2.11.121 10.2.11.138
dhcpd lease 36000
dhcpd ping_timeout 30
dhcpd domain sub.domain.net
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl trust-point ASDM_TrustPoint0 outside
webvpn
<--- More --->
anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
anyconnect profiles VPN_client_profile disk0:/VPN_client_profile.xml
anyconnect enable
tunnel-group-list enable
group-policy domain internal
group-policy domain attributes
banner value You are attempting to access secured systems at thsi facility. All activity is monitored and recorded. Disconnect now if you are not authorized to access these systems or do not possess valid logon credentials.
wins-server value 10.2.11.121 10.2.11.138
dns-server value 10.2.11.121 10.2.11.138
vpn-idle-timeout none
vpn-filter value vpn_access_in
vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value domain_splitTunnelAcl
default-domain value sub.domain.net
split-dns value sub.domain.net
group-policy DfltGrpPolicy attributes
dns-server value 10.2.11.121 10.2.11.138
vpn-filter value outside_access_in
vpn-tunnel-protocol l2tp-ipsec
default-domain value sub.domain.net
split-dns value sub.domain.net
address-pools value VPNUsers
username **** password **** encrypted privilege 15
<--- More --->
username **** password **** encrypted privilege 15
username **** attributes
webvpn
anyconnect keep-installer installed
anyconnect dtls compression lzs
anyconnect ssl dtls enable
anyconnect profiles value VPN_client_profile type user
tunnel-group DefaultL2LGroup general-attributes
default-group-policy domain
tunnel-group DefaultRAGroup general-attributes
address-pool VPNUsers
authentication-server-group ActiveDirectory
default-group-policy domain
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
ikev1 trust-point ASDM_TrustPoint0
tunnel-group DefaultWEBVPNGroup general-attributes
default-group-policy domain
tunnel-group domain type remote-access
tunnel-group domain general-attributes
address-pool (inside) VPNUsers
address-pool VPNUsers
authentication-server-group ActiveDirectory LOCAL
authentication-server-group (inside) ActiveDirectory LOCAL
<--- More --->
default-group-policy domain
dhcp-server link-selection 10.2.11.121
tunnel-group domain ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
<--- More --->
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly 21
subscribe-to-alert-group configuration periodic monthly 21
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:2578e19418cb5c61eaf15e9e2e5338a0
: end

Similar Messages

Cisco ASA 5510 - Cisco Client Can Connect To VPN But Can't Ping!

Hi,
I have an ASA 5510 with the configuration below. I have configure the ASA as remote access vpn server with cisco vpn client, my problem now is I can connect but I can't ping.
Config
ciscoasa# sh run
: Saved
ASA Version 8.0(3)
hostname ciscoasa
enable password 5QB4svsHoIHxXpF/ encrypted
names
name xxx.xxx.xxx.xxx SAP_router_IP_on_SAP
name xxx.xxx.xxx.xxx ISA_Server_second_external_IP
name xxx.xxx.xxx.xxx Mail_Server
name xxx.xxx.xxx.xxx IncomingIP
name xxx.xxx.xxx.xxx SAP
name xxx.xxx.xxx.xxx WebServer
name xxx.xxx.xxx.xxx cms_eservices_projects_sharepointold
name 192.168.2.2 isa_server_outside
interface Ethernet0/0
nameif outside
security-level 0
ip address IncomingIP 255.255.255.248
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.253 255.255.255.0
management-only
passwd 123
ftp mode passive
clock timezone EEST 2
clock summer-time EEDT recurring last Sun Mar 3:00 last Sun Oct 4:00
object-group service TCP_8081 tcp
port-object eq 8081
object-group service DM_INLINE_TCP_1 tcp
port-object eq 3389
port-object eq ftp
port-object eq www
port-object eq https
port-object eq smtp
port-object eq pop3
port-object eq 3200
port-object eq 3300
port-object eq 3600
port-object eq 3299
port-object eq 3390
port-object eq 50000
port-object eq 3396
port-object eq 3397
port-object eq 3398
port-object eq imap4
port-object eq 587
port-object eq 993
port-object eq 8000
port-object eq 8443
port-object eq telnet
port-object eq 3901
group-object TCP_8081
port-object eq 1433
port-object eq 3391
port-object eq 3399
port-object eq 8080
port-object eq 3128
port-object eq 3900
port-object eq 3902
port-object eq 7777
port-object eq 3392
port-object eq 3393
port-object eq 3394
port-object eq 3395
port-object eq 92
port-object eq 91
port-object eq 3206
port-object eq 8001
port-object eq 8181
port-object eq 7778
port-object eq 8180
port-object eq 22222
port-object eq 11001
port-object eq 11002
port-object eq 1555
port-object eq 2223
port-object eq 2224
object-group service RDP tcp
port-object eq 3389
object-group service 3901 tcp
description 3901
port-object eq 3901
object-group service 50000 tcp
description 50000
port-object eq 50000
object-group service Enable_Transparent_Tunneling_UDP udp
port-object eq 4500
access-list inside_access_in remark connection to SAP
access-list inside_access_in extended permit ip 192.168.2.0 255.255.255.0 host SAP_router_IP_on_SAP
access-list inside_access_in remark VPN Outgoing - PPTP
access-list inside_access_in extended permit tcp 192.168.2.0 255.255.255.0 any eq pptp
access-list inside_access_in remark VPN Outgoing - GRE
access-list inside_access_in extended permit gre 192.168.2.0 255.255.255.0 any
access-list inside_access_in remark VPN - GRE
access-list inside_access_in extended permit gre any any
access-list inside_access_in remark VPN Outgoing - IKE Client
access-list inside_access_in extended permit udp 192.168.2.0 255.255.255.0 any eq isakmp
access-list inside_access_in remark VPN Outgoing - IPSecNAT - T
access-list inside_access_in extended permit udp 192.168.2.0 255.255.255.0 any eq 4500
access-list inside_access_in remark DNS Outgoing
access-list inside_access_in extended permit udp any any eq domain
access-list inside_access_in remark DNS Outgoing
access-list inside_access_in extended permit tcp any any eq domain
access-list inside_access_in remark Outoing Ports
access-list inside_access_in extended permit tcp 192.168.2.0 255.255.255.0 any object-group DM_INLINE_TCP_1
access-list inside_access_in extended permit ip 172.16.1.0 255.255.255.0 any
access-list outside_access_in extended permit ip any any
access-list outside_access_in extended permit tcp any any eq pptp
access-list outside_access_in extended permit gre any any
access-list outside_access_in extended permit gre any host Mail_Server
access-list outside_access_in extended permit tcp any host Mail_Server eq pptp
access-list outside_access_in extended permit esp any any
access-list outside_access_in extended permit ah any any
access-list outside_access_in extended permit udp any any eq isakmp
access-list outside_access_in extended permit udp any any object-group Enable_Transparent_Tunneling_UDP
access-list VPN standard permit 192.168.2.0 255.255.255.0
access-list corp_vpn extended permit ip 192.168.2.0 255.255.255.0 172.16.1.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu management 1500
ip local pool POOL 172.16.1.10-172.16.1.20 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-603.bin
no asdm history enable
arp timeout 14400
nat-control
global (outside) 2 Mail_Server netmask 255.0.0.0
global (outside) 1 interface
global (inside) 2 interface
nat (inside) 0 access-list corp_vpn
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp Mail_Server 8001 ISA_Server_second_external_IP 8001 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 8000 ISA_Server_second_external_IP 8000 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server pptp isa_server_outside pptp netmask 255.255.255.255
static (inside,outside) tcp Mail_Server smtp isa_server_outside smtp netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 587 isa_server_outside 587 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 9444 isa_server_outside 9444 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 9443 isa_server_outside 9443 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 3389 isa_server_outside 3389 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 3390 isa_server_outside 3390 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server 3901 isa_server_outside 3901 netmask 255.255.255.255
static (inside,outside) tcp SAP 50000 isa_server_outside 50000 netmask 255.255.255.255
static (inside,outside) tcp SAP 3200 isa_server_outside 3200 netmask 255.255.255.255
static (inside,outside) tcp SAP 3299 isa_server_outside 3299 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server www isa_server_outside www netmask 255.255.255.255
static (inside,outside) tcp Mail_Server https isa_server_outside https netmask 255.255.255.255
static (inside,outside) tcp Mail_Server pop3 isa_server_outside pop3 netmask 255.255.255.255
static (inside,outside) tcp Mail_Server imap4 isa_server_outside imap4 netmask 255.255.255.255
static (inside,outside) tcp cms_eservices_projects_sharepointold 9999 isa_server_outside 9999 netmask 255.255.255.255
static (inside,outside) 192.168.2.0 access-list corp_vpn
access-group outside_access_in in interface outside
access-group inside_access_in in interface inside
route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.2.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 management
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set transet esp-des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map dynmap 10 set pfs
crypto dynamic-map dynmap 10 set transform-set transet ESP-3DES-SHA
crypto map cryptomap 10 ipsec-isakmp dynamic dynmap
crypto map cryptomap interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
no crypto isakmp nat-traversal
telnet 192.168.2.0 255.255.255.0 inside
telnet 192.168.1.0 255.255.255.0 management
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd dns xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx interface inside
dhcpd domain domain.local interface inside
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics access-list
tftp-server management 192.168.1.123 /
group-policy mypolicy internal
group-policy mypolicy attributes
split-tunnel-policy tunnelspecified
split-tunnel-network-list value VPN
username vpdn password 123
username vpdn attributes
vpn-group-policy mypolicy
service-type remote-access
tunnel-group mypolicy type remote-access
tunnel-group mypolicy general-attributes
address-pool POOL
default-group-policy mypolicy
tunnel-group mypolicy ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect pptp
service-policy global_policy global
prompt hostname context
Cryptochecksum:b8bb19b6cb05cfa9ee125ad7bc5444ac
: end
Thank you very much.

Here is the output:
ciscoasa# packet-tracer input outside icmp 172.16.1.10 8 0 192.168.2.1
Phase: 1
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
Phase: 2
Type: UN-NAT
Subtype: static
Result: ALLOW
Config:
static (inside,outside) 192.168.2.0 access-list corp_vpn
nat-control
match ip inside 192.168.2.0 255.255.255.0 outside 172.16.1.0 255.255.255.0
    static translation to 192.168.2.0
    translate_hits = 0, untranslate_hits = 139
Additional Information:
NAT divert to egress interface inside
Untranslate 192.168.2.0/0 to 192.168.2.0/0 using netmask 255.255.255.0
Phase: 3
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group outside_access_in in interface outside
access-list outside_access_in extended permit ip any any
Additional Information:
Phase: 4
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 5
Type: CP-PUNT
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 6
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
class-map inspection_default
match default-inspection-traffic
policy-map global_policy
class inspection_default
inspect icmp
service-policy global_policy global
Additional Information:
Phase: 7
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
Additional Information:
Phase: 8
Type: VPN
Subtype: ipsec-tunnel-flow
Result: ALLOW
Config:
Additional Information:
Phase: 9
Type: NAT-EXEMPT
Subtype: rpf-check
Result: ALLOW
Config:
Additional Information:
Phase: 10
Type: NAT
Subtype: rpf-check
Result: ALLOW
Config:
static (inside,outside) 192.168.2.0 access-list corp_vpn
nat-control
match ip inside 192.168.2.0 255.255.255.0 outside 172.16.1.0 255.255.255.0
    static translation to 192.168.2.0
    translate_hits = 0, untranslate_hits = 140
Additional Information:
Phase: 11
Type: ACCESS-LIST
Subtype:
Result: DROP
Config:
Implicit Rule
Additional Information:
Result:
input-interface: outside
input-status: up
input-line-status: up
output-interface: inside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule

VPN client connected to VPN but can't ping or access to server

HI ,
i need help urgently, had been troubleshooting for a day, but have no ideal what wrong with the config.
Basically there is 2 set of VPN configured, one is site to site IPSEC VPN and another one is connect via VPN client software coexist in same router.
This recently we having problem on client can't access or ping to internal server which is 192.168.6.3 from VPN client software.
VPN client will connect to VPN ip pool as10.20.1.0 to 10.20.1.100
Software itself shown connected but request time out when ping.
Below is the config. Some of the command might be extra as when i did some test, but end up didn't work.
aaa new-model
aaa authentication login userauthen local
aaa authorization network adminmap group VPNClient
aaa authorization network groupauthor local
aaa authorization network map-singapore local
crypto isakmp policy 10
encr 3des
authentication pre-share
group 2
crypto isakmp key emptyspace address 203.142.83.218 no-xauth
crypto isakmp keepalive 15 periodic
crypto isakmp client configuration address-pool local ippool
crypto isakmp client configuration group map-singapore
key cisco123
dns 192.168.6.3
domain cisco.com
pool ippool
acl 102
crypto isakmp profile VPNclient
   match identity address 27.54.43.210 255.255.255.255
   match identity group vpnclient
   client authentication list userauthen
   client configuration address respond
crypto ipsec security-association idle-time 86400
crypto ipsec transform-set REMSET esp-3des esp-md5-hmac
crypto ipsec transform-set DYNSET esp-aes esp-md5-hmac
crypto ipsec transform-set esp-3des-sha esp-3des esp-sha-hmac
crypto dynamic-map dynmap 10
set transform-set DYNSET
set isakmp-profile VPNclient
reverse-route
crypto map VPNMAP client authentication list userauthen
crypto map VPNMAP isakmp authorization list map-singapore
crypto map VPNMAP client configuration address respond
crypto map VPNMAP 10 ipsec-isakmp dynamic dynmap
crypto map VPNMAP 11 ipsec-isakmp
description VPN to ASA5520
set peer 203.142.83.218
set security-association lifetime kilobytes 14608000
set security-association lifetime seconds 86400
set transform-set REMSET
match address 100
interface GigabitEthernet0/0
ip address 27.54.43.210 255.255.255.240
ip nat outside
no ip virtual-reassembly
duplex full
speed 100
crypto map VPNMAP
interface GigabitEthernet0/1
ip address 192.168.6.1 255.255.255.0
ip nat inside
no ip virtual-reassembly
duplex full
speed 100
interface GigabitEthernet0/2
description $ES_LAN$
no ip address
shutdown
duplex auto
speed auto
ip local pool ippool 10.20.1.0 10.20.1.100
ip forward-protocol nd
ip pim bidir-enable
no ip http server
ip http authentication local
no ip http secure-server
ip nat inside source list 1 interface GigabitEthernet0/0 overload
ip nat inside source list 101 interface GigabitEthernet0/0 overload
ip nat inside source route-map nonat interface GigabitEthernet0/0 overload
ip nat inside source static 192.168.6.3 27.54.43.212
ip route 0.0.0.0 0.0.0.0 27.54.43.209
ip route 192.168.1.0 255.255.255.0 27.54.43.209
ip route 192.168.151.0 255.255.255.0 192.168.6.151
ip route 192.168.208.0 255.255.255.0 27.54.43.209
ip access-list extended RA_SING
permit ip 192.168.6.0 0.0.0.255 192.168.1.0 0.0.0.255
permit ip 192.168.6.0 0.0.0.255 10.0.0.0 0.255.255.255
permit ip 10.0.0.0 0.255.255.255 192.168.6.0 0.0.0.255
permit ip 192.168.6.0 0.0.0.255 192.168.208.0 0.0.0.255
permit ip 10.20.1.1 0.0.0.100 192.168.6.0 0.0.0.255
permit ip 10.20.1.0 0.0.0.255 10.0.0.0 0.255.255.255
deny   ip any any log
access-list 1 remark Local Network
access-list 1 permit 192.168.6.0 0.0.0.255
access-list 1 permit 192.168.102.0 0.0.0.255
access-list 1 permit 192.168.151.0 0.0.0.255
access-list 2 remark VPNClient-range
access-list 2 permit 10.0.0.0 0.255.255.255
access-list 10 permit 192.168.6.0 0.0.0.255
access-list 10 permit 192.168.102.0 0.0.0.255
access-list 10 permit 192.168.151.0 0.0.0.255
access-list 10 permit 10.0.0.0 0.255.255.255
access-list 100 permit ip 192.168.6.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 100 permit ip 192.168.102.0 0.0.0.255 192.168.1.0 0.0.0.255
access-list 100 permit ip 192.168.6.0 0.0.0.255 192.168.208.0 0.0.0.255
access-list 100 permit ip host 192.168.6.7 host 192.168.208.48
access-list 101 deny   ip 192.168.6.0 0.0.0.255 10.0.0.0 0.255.255.255
access-list 101 permit ip 10.0.0.0 0.255.255.255 any
access-list 101 permit ip 192.168.6.0 0.0.0.255 any
access-list 102 permit ip 10.0.0.0 0.255.255.255 any
access-list 120 deny   ip any any log
access-list 120 deny   ip 192.168.6.0 0.0.0.255 192.168.1.0 0.0.0.255 log
access-list 120 deny   ip 192.168.6.0 0.0.0.255 10.0.0.0 0.255.255.255
access-list 120 deny   ip 192.168.6.0 0.0.0.255 192.168.208.0 0.0.0.255
no cdp run
route-map nonat permit 10
match ip address 120
control-plane
alias isakmp-profile sh crypto isakmp sa
alias exec ipsec sh crypto ipsec sa
banner motd ^CC^C

I did not try to ping 4.2.2.2. I just know I can not ping comcasts dns servers. I have updated the firmware on the router and it did not work. The computer was able to access the internet until about a week ago, I don't understand what could have changed that I would now need a static DNS.

Intermittent Internet Connection and VPN clients can't ping internal LAN but connected after installating cisco ASA5512x

Hi!
I wish someone can help me on this, I'm a new guy on cisco firewalls and I'm currently implementing cisco asa 5512x, here are the details:
ISP -> Firewall -> Core switch -> Internal LAN
after installing the cisco asa and terminating the appropriate lan for the outside and inside interfaces, internet seems intermittent and cisco vpn client can connect with internet connection but can't ping internal LAN.
here's my configuration from my firewall.
ASA Version 8.6(1)2
hostname ciscofirewall
enable password 2KFQnbNIdI.2KYOU encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 203.x.x.x 255.255.255.0
interface GigabitEthernet0/1
nameif inside
security-level 100
ip address 10.152.11.15 255.255.255.0
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
management-only
ftp mode passive
dns domain-lookup outside
dns domain-lookup inside
dns server-group DefaultDNS
name-server 4.2.2.2 -------> public DNS
name-server 8.8.8.8 -------> public
name-server 203.x.x.x ----> Clients DNS
name-server 203.x.x.x -----> Clients DNS
same-security-traffic permit intra-interface
object network net_access
subnet 10.0.0.0 255.0.0.0
object network citrix_server
host 10.152.11.21
object network NETWORK_OBJ_10.10.10.0_28
subnet 10.10.10.0 255.255.255.240
object network NETWORK_OBJ_10.0.0.0_8
subnet 10.0.0.0 255.0.0.0
object network InterconHotel
subnet 10.152.11.0 255.255.255.0
access-list net_surf extended permit ip any any
access-list net_surf extended permit ip object NETWORK_OBJ_10.10.10.0_28 object InterconHotel
access-list outside_access extended permit tcp any object citrix_server eq www
access-list outside_access extended permit ip object NETWORK_OBJ_10.10.10.0_28 any
access-list outsidevpn_splitTunnelAcl standard permit 10.152.11.0 255.255.255.0
access-list LAN_Users remark LAN_clients
access-list LAN_Users standard permit any
access-list vpnpool extended permit ip 10.10.10.0 255.255.255.248 any
pager lines 24
logging enable
logging asdm informational
mtu management 1500
mtu outside 1500
mtu inside 1500
ip local pool vpnpool 10.10.10.1-10.10.10.6 mask 255.255.255.248
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source static NETWORK_OBJ_10.10.10.0_28 NETWORK_OBJ_10.10.10.0_28 destination static NETWORK_OBJ_10.10.10.0_28 NETWORK_OBJ_10.10.10.0_28 no-proxy-arp route-lookup
object network net_access
nat (inside,outside) dynamic interface
object network citrix_server
nat (inside,outside) static 203.177.18.234 service tcp www www
object network NETWORK_OBJ_10.10.10.0_28
nat (any,outside) dynamic interface
object network InterconHotel
nat (inside,outside) dynamic interface dns
access-group outside_access in interface outside
access-group net_surf out interface outside
route outside 0.0.0.0 0.0.0.0 203.x.x.x 1
route outside 10.10.10.0 255.255.255.248 10.152.11.15 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication telnet console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 10.0.0.100 255.255.255.255 inside
http 10.10.10.0 255.255.255.240 outside
http 0.0.0.0 0.0.0.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto ikev1 enable outside
crypto ikev1 enable inside
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
client-update enable
telnet 10.152.11.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.1.2-192.168.1.254 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
webvpn
enable outside
anyconnect-essentials
group-policy outsidevpn internal
group-policy outsidevpn attributes
dns-server value 203.x.x.x 203.x.x.x
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client
split-tunnel-policy tunnelall
split-tunnel-network-list value outsidevpn_splitTunnelAcl
default-domain value interconti.com
address-pools value vpnpool
username test1 password i1lji/GiOWB67bAs encrypted privilege 5
username test1 attributes
vpn-group-policy outsidevpn
username mnlha password WlzjmENGEEZmT9LA encrypted
username mnlha attributes
vpn-group-policy outsidevpn
username cisco password 3USUcOPFUiMCO4Jk encrypted privilege 15
tunnel-group outsidevpn type remote-access
tunnel-group outsidevpn general-attributes
address-pool (inside) vpnpool
address-pool vpnpool
authentication-server-group (outside) LOCAL
default-group-policy outsidevpn
tunnel-group outsidevpn ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
inspect http
inspect ipsec-pass-thru
class class-default
user-statistics accounting
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
hpm topN enable
Cryptochecksum:edc30dda08e5800fc35b72dd6e1d88d7
: end
thanks. please help.

I think you should change your nat-exemption rule to smth more general, like
nat (inside,outside) source static any any destination static NETWORK_OBJ_10.10.10.0_28 NETWORK_OBJ_10.10.10.0_28 no-proxy-arp route-lookup
'cause your inside networks are not the same as your vpn-pool subnet.
Plus, if you're trying to reach inside subnets, different from 10.152.11.0 255.255.255.0 (ip from wich subnet is assignet to your inside interface, and for wich above nat exception should be enough), you should check if routing is configured from that subnets to your vpn-pool-subnet through the ASA.

I can connect my cisco mobile vpn but can't ping & access internal IP

Hi somebody,
i've configured mobile vpn configuration in cisco 7200 with GNS3. i can connect VPN to my cisco router with cisco vpn client software from outside. but i can't ping to internal ip and can't access internal resources.
My Internal IP is 192.168.1.x . And IP for mobile VPN client from outside is 172.60.1.x.
Your advise will be appreciate.
here is my configuration with cisco 7200 in GNS 3,
OfficeVPN_Router#sh run
Building configuration...
Current configuration : 2186 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname OfficeVPN_Router
boot-start-marker
boot-end-marker
enable secret 5 $1$E0Gz$U8UzNtHOXy2CeoEFj30by0
aaa new-model
aaa authentication login userlist local
aaa authorization network grouplist local
aaa session-id common
ip cef
no ip domain lookup
username asm privilege 15 password 0 pncsadmin
username user privilege 15 password 0 pncsadmin
username user1 privilege 15 password 0 pncsadmin
username cisco123 secret 5 $1$lCOc$Db.e8AFd/0f02ZI4/aeV./
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
crypto isakmp client configuration group MWG
key cisco
dns 165.21.83.88
pool vpnpool
acl 101
netmask 255.255.0.0
crypto ipsec transform-set myset esp-aes esp-sha-hmac
crypto dynamic-map dynmap 10
set transform-set myset
reverse-route
crypto map mymap client authentication list userlist
crypto map mymap isakmp authorization list grouplist
crypto map mymap client configuration address initiate
crypto map mymap client configuration address respond
crypto map mymap 10 ipsec-isakmp dynamic dynmap
interface FastEthernet0/0
no ip address
shutdown
duplex half
interface FastEthernet1/0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex full
speed 100
interface FastEthernet1/1
ip address 200.200.200.200 255.255.255.0
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map mymap
ip local pool vpnpool 172.60.1.10 172.60.1.100
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 200.200.200.201
no ip http server
no ip http secure-server
ip nat inside source list 111 interface FastEthernet1/1 overload
access-list 101 permit ip 192.168.1.0 0.0.0.255 172.60.0.0 0.0.255.255
access-list 111 deny ip 192.168.1.0 0.0.0.255 172.60.0.0 0.0.255.255
access-list 111 permit ip any any
control-plane
gatekeeper
shutdown
line con 0
exec-timeout 0 0
password cisco123
logging synchronous
stopbits 1
line aux 0
stopbits 1
line vty 0 4
password cisco123
end
OfficeVPN_Router#sh ver
Cisco IOS Software, 7200 Software (C7200-A3JK9S-M), Version 12.4(25), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Tue 21-Apr-09 18:50 by prod_rel_team
ROM: ROMMON Emulation Microcode
BOOTLDR: 7200 Software (C7200-A3JK9S-M), Version 12.4(25), RELEASE SOFTWARE (fc2)
OfficeVPN_Router uptime is 30 minutes
System returned to ROM by unknown reload cause - suspect boot_data[BOOT_COUNT] 0x0, BOOT_COUNT 0, BOOTDATA 19
System image file is "tftp://255.255.255.255/unknown"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 7206VXR (NPE400) processor (revision A) with 245760K/16384K bytes of memory.
Processor board ID 4279256517
R7000 CPU at 150MHz, Implementation 39, Rev 2.1, 256KB L2 Cache
6 slot VXR midplane, Version 2.1
Last reset from power-on
PCI bus mb0_mb1 (Slots 0, 1, 3 and 5) has a capacity of 600 bandwidth points.
Current configuration on bus mb0_mb1 has a total of 600 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
PCI bus mb2 (Slots 2, 4, 6) has a capacity of 600 bandwidth points.
Current configuration on bus mb2 has a total of 0 bandwidth points
This configuration is within the PCI bus capacity and is supported.
Please refer to the following document "Cisco 7200 Series Port Adaptor
Hardware Configuration Guidelines" on Cisco.com <http://www.cisco.com>
for c7200 bandwidth points oversubscription and usage guidelines.
3 FastEthernet interfaces
125K bytes of NVRAM.
65536K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
8192K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x2102
OfficeVPN_Router#

Dear Javier ,
Thanks for your info. i already tested as you say. but still i can't use & ping to my internal IP which is behind cisco VPN router. i posted my config file.
OfficeVPN_Router(config)#ip access-list resequence 111 10 10
OfficeVPN_Router(config)#do sh run
Building configuration...
Current configuration : 2201 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname OfficeVPN_Router
boot-start-marker
boot-end-marker
enable secret 5 $1$E0Gz$U8UzNtHOXy2CeoEFj30by0
aaa new-model
aaa authentication login userlist local
aaa authorization network grouplist local
aaa session-id common
ip cef
no ip domain lookup
username asm privilege 15 password 0 pncsadmin
username user privilege 15 password 0 pncsadmin
username user1 privilege 15 password 0 pncsadmin
username cisco123 secret 5 $1$lCOc$Db.e8AFd/0f02ZI4/aeV./
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
crypto isakmp client configuration group MWG
key cisco
dns 165.21.83.88
pool vpnpool
acl 101
netmask 255.255.0.0
crypto ipsec transform-set myset esp-aes esp-sha-hmac
crypto dynamic-map dynmap 10
set transform-set myset
reverse-route
crypto map mymap client authentication list userlist
crypto map mymap isakmp authorization list grouplist
crypto map mymap client configuration address initiate
crypto map mymap client configuration address respond
crypto map mymap 10 ipsec-isakmp dynamic dynmap
interface FastEthernet0/0
no ip address
shutdown
duplex half
interface FastEthernet1/0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex full
speed 100
interface FastEthernet1/1
ip address 200.200.200.200 255.255.255.0
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map mymap
ip local pool vpnpool 172.60.1.10 172.60.1.100
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 200.200.200.201
no ip http server
no ip http secure-server
ip nat inside source list 111 interface FastEthernet1/1 overload
access-list 101 permit ip 192.168.1.0 0.0.0.255 172.60.0.0 0.0.255.255
access-list 111 deny ip 192.168.1.0 0.0.0.255 172.60.0.0 0.0.255.255
access-list 111 permit ip 192.168.1.0 0.0.0.255 any
control-plane
gatekeeper
shutdown
line con 0
exec-timeout 0 0
password cisco123
logging synchronous
stopbits 1
line aux 0
stopbits 1
line vty 0 4
password cisco123
end

Connected to WRT54GsV4 but can't ping or browse

I have a very interesting problem I am working on for a friend. They have 3 computers in the house they are a vaio laptop with Vista, a macbook, and a HP desktop with Vista. The vaio laptop connects and surfs the internet fine, so does the macbook. The desktop which is wireless like the others will connect to the router, show it has local and internet connection but can not browse the internet or ping. I also can not access the router by going to the default gateway shown by IPCONFIG. IPCONFIG also shows it connected to the DNS and has an IP but it still can't get on the internet. I have tried just about everything. We have used a USB wireless adapter and 2 different wireless NICs all to no avail. One thing that I noticed is that on the vaio laptop it shows it connected to Linksys. On the desktop it shows Linksys as the SSID but when it connects it adds _SES_### which I thought was very odd. I have ran through and reset the tcpip and flushed the DNS all to no luck. We ran a system restore back to a week before when it was working, no luck someone please help!!!!!

I did not try to ping 4.2.2.2. I just know I can not ping comcasts dns servers. I have updated the firmware on the router and it did not work. The computer was able to access the internet until about a week ago, I don't understand what could have changed that I would now need a static DNS.

Can connect via VPN, but can't access AFP server on same Xserve

Hi:
I've set up our XServe with MacOS X Server 10.5.2 to do AFP and VPN (L2TP only; PPTP is disabled). The XServe is a standalone server, not connected to any other direstory server.
I can connect to the XServe's AFP server from my Mac over our wired and wireless network. The AFP server shows up in the sidebar of Finder windows. So far, so good.
I am able to successfully connect to our network via the VPN with Mac OS X 10.5.2 client (on two different machines) using L2TP through our network's firewall (on a Netopia T1 router; UDF ports 500 and 4500 and IP Protocol 50 and 51 are open) using a shared secret.
But I cannot connect to the XServe itself to use Server Admin or AFP (using afp://server.company.com or afp://xxx.xxx.xxx.xxx via the Go > Connect to Server command).
The error I get while connecting to the 10.5.2 AFP server is Some data in apf://server.mycompany.com could not be read or written (Error Code -36 ). I saw this error associated with a SMB problem in 10.4.x, but SMB is not running.
Other iChat users in my office also do not automatically show up in the Bonjour list when I connect to the network. Other computers on our network do not appear in the sidebar of a Finder window. (I'm told these are to be expected, as Bonjour isn't supported (in the "local area Bonjour" over a WAN link - it's purely a multicast feature on the network in the office, and won't be routed across the VPN link. True?)
Now, here's the odd part. There is a second server (v10.4.11) on our network running AFP. I can connect to it (using afp://server.company.com via the Go > Connect to Server command) and mount its various sharepoints via the VPN.
The only thing I see in the VPN log that seems amiss is this (but I have no idea what it means):
Tue Mar 11 23:09:27 2008 : Unsupported protocol 0x8057 received
--Both the 10.5.2 and the 10.4.11 servers have DNS properly configured (though our ISP; we're not running our own DNS).
--Both servers and the client have public IP addresses and have the same subnet mask. Network Utility confirms this while connected to the VPN.
--NAT is not running. The ISP is responding with public IPs for the servers.
--The firewall for the 10.5.2 server is not running (but will be once I get this all working).
--The IP address range for the VPN server doesn't overlap our DHCP pool (which also currently uses public IP addresses).
--Any user can access any service.
--No network routing definitions have been set up.
--In essence, I've followed the steps on Pages 141-142 of the Network Services Admin Guide.
One other note: After I connect, the Network Preferences > VPN > Advanced > TCP/IP window shows the IP address for the client just fine (assigned from the VPN pool), but lists the router as having the IP address of the XServe (rather than the router on the network). Is that normal?
I'm hoping I don't need to have the XServe run DNS as an internal LAN DNS server.... And I'm not sure why I would have to if I can already successfully connect to the 10.4.11 AFP server .
What simple step am I missing?
TIA,
mm

"I am able to successfully connect to our network via the VPN with Mac OS X 10.5.2 client (on two different machines) using L2TP through our network's firewall (on a Netopia T1 router; UDF ports 500 and 4500 and IP Protocol 50 and 51 are open) using a shared secret."
I suspect you mean UDP ports and you might need UDP port 1701 open too.
You only need IP protocol 50 (ESP), protocol 51 (AH) isn't used. And ESP is only used when client and server isn't behind NAT (when NAT is used only the UDP ports are used).
"Unsupported protocol 0x8057 received"
This is usually seen when you can't get GRE through but since you don't use PPTP I can't be sure why this is registered in the logs. Sometimes when connecting using PPTP you have to disconnect and then reconnect for everything to work - you might try this for L2TP too.
But if you already can reach services on any LAN nodes through the VPN I wouldn't bother with it.
As you have a firewall in front of the server you need a second alias IP on the server that you can use to get at the services running on the server through the VPN. The firewall blocks all ports protocols not opened - that's why you can't use the server main IP even if the VPN is up.
The netmask is used by all nodes to determine how big your subnet is: what part of the IP number is the network number and what range the node number is in => really: should traffic be directed to a node on the same LAN or sent directly to the gw/router for forwarding.
What you can't do is connect from a NATed network to another NATed network that both are using the same network number. (That's why people should stay away from using the "default" 192.168.0.0/24 and 192.168.1.0/24 networks for VPN server LANs).
Try your settings at http://www.jodies.de/ipcalc to see what I mean.
"...lists the router as having the IP address of the XServe (rather than the router on the network). Is that normal?"
Yes. The VPN server is the VPN gw/router.
"The firewall for the 10.5.2 server is not running (but will be once I get this all working)."
If you already have a firewall in front of your servers that is a bit redundant.
"--No network routing definitions have been set up."
"I'm hoping I don't need to have the XServe run DNS as an internal LAN DNS server"
You need routing definitions if you want to setup a split tunnel VPN or all traffic is routed through the VPN when connected. The VPN becomes the default gw.
Without ipforwarding ON in the server you can only reach nodes on the server LAN - not Internet.
DNS is needed for your servers forward and reverse names/IPs for advanced services but doesn't need to run in any of your own servers.
If you decide to do a split tunnel VPN config (adding public and private routing definitions) a reachable DNS IP for VPN clients (in VPN config on server) is needed for VPN clients or they can't use names to find anything. To reach this DNS IP if public/not on your server LAN, you need your server to forward IP DNS lookups and have a routing definition for it.
A split tunnel VPN only send traffic for your server LAN through the VPN and all other traffic directly to the local gw/router (Internet).

I have connected via VPN but can't see lion server .private

when I am in my local network at home I simply go to finder and click on my server and connect to it. When I VPN form the net into my servers local network I dont see it in my finder? I know I am in the next work being I did a IP Check but am I am missing something how am I to get to the server to get to my files? it is set up as a .private.

Spoke to an apple rep today. when accessing via VPN go to finder then go to the top menu click GO at the bottom of the drop down will be connect to server simply add the IP address to access.

I can Ping FW inside interface but can not connect to remote resources

dear all
i configer my asa 5520 through ASDM to enable VPN Connection , i follow the cisco steps and it works fine and the anyconnect version 3.1 in Windows 8 - one day troubleshoot for this point only - can connect and have an IP address from the range , but i have something wrong in NAT may be because all guides talking about old ASDM ( NAT Exempt) but i am confeused to apply it on the new ASDM.
i can ping the inside interface from my labtop which using anyconnect , but i can not access anything else inside my network
Please anyone has a solution , please describe it using ASDM , thanks for help
This is my configuration
interface GigabitEthernet0/1
description
nameif SRV_ZONE
security-level 50
ip address 192.168.1.1 255.255.255.0
interface GigabitEthernet0/2
description
nameif TRUST_ZONE
security-level 100
ip address 172.17.200.1 255.255.255.0
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif MGMT
security-level 0
ip address 10.10.10.1 255.255.255.0
dns server-group DefaultDNS
domain-name xxx.xxx.xxx
object network obj-192.168.1.11
host 192.168.1.11
object network obj-xxx.xxx.xxx.xxx
host xxx.xxx.xxx.xxx
object service obj-tcp-source-eq-25
service tcp source eq smtp
object network obj-192.168.1.12
host 192.168.1.12
object network obj-xxx.xxx.xxx.xxx
host xxx.xxx.xxx.xxx
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object service obj-tcp-eq-25
service tcp destination eq smtp
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network obj-0.0.0.0
host 0.0.0.0
object network obj_any-01
subnet 0.0.0.0 0.0.0.0
object network obj-172.17.8.8
host 172.17.8.8
object network obj-172.17.0.0
subnet 172.17.0.0 255.255.0.0
object network obj_any-02
subnet 0.0.0.0 0.0.0.0
object network obj_any-03
subnet 0.0.0.0 0.0.0.0
object network obj_any-04
subnet 0.0.0.0 0.0.0.0
object network obj_any-05
subnet 0.0.0.0 0.0.0.0
object network obj_any-06
subnet 0.0.0.0 0.0.0.0
object network obj.172.17.8.115
host 172.17.8.115
object network obj.xxx.xxx.xxx.xxx
host xxx.xxx.xxx.xxx
object service http
service tcp source eq www destination eq www
object network obj.xxx.xxx.xxx.xxx
host xxx.xxx.xxx.xxx
object service https
service tcp source eq https destination eq https
object service newservice
service tcp source eq pop3 destination eq pop3
object network mail
host 172.17.8.8
description mail
object network 192.168.1.11
host 192.168.1.11
description smtp
object service smtpnew
service tcp source eq 587 destination eq 587
object network VPN_RANGE
description VPN ACCESS RANGE
object network VPN_PoOL
subnet 172.17.16.0 255.255.255.0
description vpn
object-group network DM_INLINE_NETWORK_1
network-object host 192.168.1.11
network-object host 192.168.1.12
object-group network Eighth_Floor
network-object 172.17.8.0 255.255.255.0
object-group service WEB_SERVICES
service-object tcp destination eq www
object-group network ENT_SERVERS
network-object host 192.168.1.11
network-object host 192.168.1.1
object-group network DM_INLINE_NETWORK_2
network-object 172.17.200.0 255.255.255.0
network-object 172.17.8.0 255.255.255.0
object-group service DM_INLINE_TCP_2 tcp
port-object eq www
port-object eq https
port-object eq smtp
object-group service web tcp
port-object eq www
port-object eq xxx
port-object eq ftp
port-object eq xxx
port-object eq xxx
object-group service xxx_Web_and_Email
service-object object http
service-object tcp destination eq pop3
service-object tcp destination eq smtp
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object udp
protocol-object tcp
object-group protocol DM_INLINE_PROTOCOL_2
protocol-object ip
object-group protocol DM_INLINE_PROTOCOL_3
protocol-object ip
access-list DMZ_access_in extended permit ip 192.168.1.0 255.255.255.0 172.17.0.0 255.255.0.0
access-list DMZ_access_in extended permit ip 192.168.1.0 255.255.255.0 any
access-list justice_splitTunnelAcl standard permit 10.100.100.0 255.255.255.0
access-list xxx-VPN_splitTunnelAcl remark vpn
access-list xxx-VPN_splitTunnelAcl standard permit 172.17.16.0 255.255.255.0
access-list xxx-VPN_splitTunnelAcl standard permit any
access-list cap extended permit tcp any host xxx.xxx.xxx.xxx eq smtp log
access-list cap1 extended permit tcp host 192.168.1.11 any eq smtp
access-list SRV_ZONE_nat_outbound extended permit tcp 192.168.1.0 255.255.255.0 any eq smtp
access-list SRV_ZONE_nat_outbound extended permit ip host 192.168.1.11 any
access-list TRUST_ZONE_access_in extended permit ip host 172.17.88.108 any
access-list TRUST_ZONE_access_in extended permit object-group DM_INLINE_PROTOCOL_2 10.10.3.0 255.255.255.0 any
access-list TRUST_ZONE_access_in extended permit object-group DM_INLINE_PROTOCOL_3 10.10.50.0 255.255.255.0 any
access-list TRUST_ZONE_access_in extended permit ip 172.17.8.0 255.255.255.0 any
access-list TRUST_ZONE_access_in extended permit ip 172.17.200.0 255.255.255.0 any
access-list TRUST_ZONE_access_in extended permit ip 172.17.0.0 255.255.0.0 host 192.168.1.12
access-list TRUST_ZONE_cryptomap extended permit ip xxx.xxx.xxx.xxx 255.255.255.248 any
access-list outside_access_in extended permit tcp any host 192.168.1.11 eq smtp
access-list outside_access_in extended permit tcp any host 172.17.8.8 eq www
access-list outside_access_in extended permit tcp any host 192.168.1.12 object-group web
access-list outside_access_in extended permit tcp any host 172.17.8.8 eq pop3
access-list outside_access_in extended permit ip 172.17.16.0 255.255.255.0 any inactive
access-list vpn remark vpn
access-list vpn standard permit 172.17.16.0 255.255.255.0
pager lines 24
logging enable
logging trap informational
logging asdm informational
logging host TRUST_ZONE 172.17.8.100
mtu INT_ZONE 1500
mtu SRV_ZONE 1500
mtu TRUST_ZONE 1500
mtu MGMT 1500
ip local pool VPN_POOL 172.17.16.100-172.17.16.254 mask 255.255.255.0
ip verify reverse-path interface INT_ZONE
ip verify reverse-path interface SRV_ZONE
no failover
icmp unreachable rate-limit 1 burst-size 1
icmp permit any SRV_ZONE
icmp permit any TRUST_ZONE
asdm image disk0:/asdm-635.bin
no asdm history enable
arp timeout 14400
nat (SRV_ZONE,INT_ZONE) source static obj-192.168.1.11 obj-xxx.xxx.xxx.xxx service any obj-tcp-source-eq-25
nat (SRV_ZONE,INT_ZONE) source static obj-192.168.1.12 obj-xxx.xxx.xxx.xxx
nat (SRV_ZONE,INT_ZONE) source dynamic obj-192.168.1.0 interface service obj-tcp-eq-25 obj-tcp-eq-25
nat (INT_ZONE,SRV_ZONE) source static any any destination static 192.168.1.11 obj-172.17.8.8 service obj-tcp-source-eq-25 obj-tcp-source-eq-25
nat (TRUST_ZONE,INT_ZONE) source static VPN_PoOL VPN_PoOL destination static VPN_PoOL VPN_PoOL
object network obj_any
nat (SRV_ZONE,INT_ZONE) dynamic obj-0.0.0.0
object network obj_any-01
nat (SRV_ZONE,MGMT) dynamic obj-0.0.0.0
object network obj-172.17.8.8
nat (TRUST_ZONE,INT_ZONE) static xxx.xxx.xxx.xxx service tcp www www
object network obj-172.17.0.0
nat (TRUST_ZONE,SRV_ZONE) static 172.17.0.0
object network obj_any-02
nat (TRUST_ZONE,INT_ZONE) dynamic interface
object network obj_any-03
nat (TRUST_ZONE,SRV_ZONE) dynamic interface
object network obj_any-04
nat (TRUST_ZONE,INT_ZONE) dynamic obj-0.0.0.0
object network obj_any-05
nat (TRUST_ZONE,SRV_ZONE) dynamic obj-0.0.0.0
object network obj_any-06
nat (TRUST_ZONE,MGMT) dynamic obj-0.0.0.0
object network obj.172.17.8.115
nat (TRUST_ZONE,INT_ZONE) static obj.xxx.xxx.xxx.xxx service tcp www www
object network mail
nat (TRUST_ZONE,INT_ZONE) static obj-xxx.xxx.xxx.xxx service tcp pop3 pop3
nat (TRUST_ZONE,INT_ZONE) after-auto source static obj-172.17.8.8 obj-xxx.xxx.xxx.xxx service https https
access-group outside_access_in in interface INT_ZONE
access-group DMZ_access_in in interface SRV_ZONE
access-group TRUST_ZONE_access_in in interface TRUST_ZONE
route INT_ZONE 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1
route TRUST_ZONE 10.10.0.0 255.255.0.0 172.17.200.254 1
route TRUST_ZONE 10.11.0.0 255.255.0.0 172.17.200.254 1
route TRUST_ZONE 10.12.0.0 255.255.0.0 172.17.200.254 1
route TRUST_ZONE 10.13.0.0 255.255.0.0 172.17.200.254 1
route TRUST_ZONE 172.17.0.0 255.255.0.0 172.17.200.254 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication enable console LOCAL
aaa authentication http console LOCAL
aaa authentication ssh console LOCAL
aaa authentication serial console LOCAL
http server enable
http 172.17.8.0 255.255.255.0 TRUST_ZONE
http 172.17.8.155 255.255.255.255 TRUST_ZONE
http 172.17.8.45 255.255.255.255 TRUST_ZONE
http 10.10.10.2 255.255.255.255 MGMT
http 192.168.1.12 255.255.255.255 SRV_ZONE
http 0.0.0.0 0.0.0.0 INT_ZONE
http 172.17.200.0 255.255.255.0 TRUST_ZONE
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map pol 1 match address TRUST_ZONE_cryptomap
crypto dynamic-map pol 1 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map INT_ZONE_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map TRUST_ZONE_map0 1 ipsec-isakmp dynamic pol
crypto map TRUST_ZONE_map0 interface TRUST_ZONE
crypto map INT_ZONE_map0 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map INT_ZONE_map0 interface INT_ZONE
crypto ca trustpoint ASDM_TrustPoint0
enrollment self
fqdn SEC-xxx-FW1
subject-name CN=SEC-xxx-FW1
no client-types
proxy-ldc-issuer
crl configure
crypto ca trustpoint ASDM_TrustPoint1
enrollment self
subject-name CN=SEC-xxx-FW1
keypair sslvpnkeypair
crl configure
crypto ca certificate chain ASDM_TrustPoint0
certificate 31
    57f4e52e 6b851966 77515d62 c209a0df 1c32ce94 bb90cbce 497cfd04 6745ea85
    efb75f85 2ae1ad35 344d94ab 915e01ab d3292626 ac697a52 b4ed6632 d3ed2332 ae
quit
crypto ca certificate chain ASDM_TrustPoint1
certificate e6054352
    c64f3661 30f14c3d 06b5f039 9f14560d 3b154fd1 42782268 7531689e 8e547d91
    85e88415 e326f653 74733a6c a3f5c935 f7e83f56 f6
quit
crypto isakmp enable INT_ZONE
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 INT_ZONE
ssh 172.17.8.0 255.255.255.0 TRUST_ZONE
ssh 10.10.10.2 255.255.255.255 MGMT
ssh timeout 5
console timeout 0
management-access TRUST_ZONE
vpn load-balancing
interface lbpublic INT_ZONE
interface lbprivate INT_ZONE
priority-queue INT_ZONE
tx-ring-limit 256
threat-detection basic-threat
threat-detection scanning-threat
threat-detection statistics host number-of-rate 3
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl trust-point ASDM_TrustPoint1 INT_ZONE
webvpn
enable INT_ZONE
svc image disk0:/anyconnect-win-2.1.0148-k9.pkg 1
svc enable
tunnel-group-list enable
group-policy xxx-VPN internal
group-policy xxx-VPN attributes
dns-server value xx.xx.xx.xx xx.xx.xx.xx
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value xxx-VPN_splitTunnelAcl
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol webvpn
group-policy GPNEW internal
group-policy GPNEW attributes
dns-server value 172.17.8.41
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
default-domain value xxx.xxx.xxx
address-pools value VPN_POOL
username VPNAM password xxx encrypted
username VPNAM attributes
service-type remote-access
vpn-group-policy xxx-VPN
tunnel-group xxx-VPN type remote-access
tunnel-group xxx-VPN general-attributes
dhcp-server 172.17.8.41
tunnel-group xxx-VPN ipsec-attributes
pre-shared-key *****
tunnel-group pol type ipsec-l2l
tunnel-group pol ipsec-attributes
pre-shared-key *****
trust-point ASDM_TrustPoint0
tunnel-group SSLClientProfile type remote-access
tunnel-group SSLClientProfile general-attributes
address-pool VPN_POOL
default-group-policy GPNEW
tunnel-group SSLClientProfile webvpn-attributes
group-alias SSLVPNClient enable
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect ip-options
inspect pptp
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:78a941e3f509dec8f3570c60061eedaa
: end

thanks god
i solve the problem
the problem is in NAT
i creat an object with the ip address host from VPN pool and name it vpn
then i do the nat from inside to that host as the following picture...
trust zone is the inside zone
vpn is the outside vpn host...
thanks and hope it helps anyone else...

TS3992 i have the message that the ipad has not been backed up successfully in 2 weeks, but can not get past the message to use the Ipad

I am trying to unlock my ipad with the message that the ipad has not been backed up successfully in 2 weeks, but can not get past this screen. I have plugged it in, it is connected to the internet, but will not back up or do anything else. What can I do?

Welcome to the Apple Support Communities
Hold Sleep and Home buttons until the iPad restarts, so you will be able to use your iPad

Got my password wrong twice and my mini is disable. I connected to iTunes, but can't get it to work. Can some one guide my through?

got my password wrong twice and my mini is disable. I connected to iTunes, but can't get it to work. Can some one guide my through?

If it's showing the red disabled screen due to incorrect passcodes then you may need to put the iPad into recovery mode : http://support.apple.com/kb/ht1808 - you should then be able to reset the iPad via your computer's iTunes and restore/resync your content to it

I already have a valid payment method for my iTunes account, but can't get past the Family Sharing setup prompt telling me to add a payment method . What to do?

I already have a valid payment method for my iTunes account, but can't get past the Family Sharing setup prompt telling me to add a payment method . What to do?

I had the same problem and found a bunch of others did, too. Unfortunately all the posts had no responses! Anyway, I previously had my payment method linked to my paypal. I tried changing it to my credit card and it worked. Don't know if there's a bug with using paypal but that seemed to be the culprit for me. Good luck!

HT2497 Connected to wifi but can't get on internet on MacBook Pro laptop

Connected to wifi but can't use internet on laptop??

Information.
Can’t Connect to the Internet
Can’t Connect to the Internet (2)
Connect to the Internet – Solutions and Troubleshooting
Connecting to the Internet - Solve Problems

I am connected to wifi, but can't open webpages or collect mail

I am connected to wifi, but can't open webpages or collect mail. I have tried to reconnect; to forget the network, all those things that should hepl. My phone and my computer recognize the network, the ipad doesn't. I mean I am connected and have a full scala of connection bows, but nothing happens.

You iPad recognizes the wifi signal, but is not connected.
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

I recently added photoshop elements 12 to my computer but can't get past the initial log in screen. It goes gray and spins. any thoughts?

I recently added photoshop elements 12 to my computer but can't get past the initial log in screen. It goes gray and spins. I have a current serial number and log in ID/password but still not working. Any thoughts?

Hello,
I recommend you contact AT&T's dedicated BB Support staff (call their front line, request escalation to BB Support) and have them check to be sure that your account with them is correctly configured for this device. Sometimes when switching devices things don't fully automatically move behind the scenes, and only they (ATT) can validate that.
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Connect to VPN but can't ping past inside interface

Similar Messages

Maybe you are looking for