Connect to wlan using eaptls

I prepared a configuration profile in ICU for authentication of my MAC in WLAN using EAP TLS with certificate. On MAC (Lion and Mountain Lion)
it works well. I applied the same profile to my iPhone (iOS 6.1.3) and Iphone does not join WLAN. On debug console I found
Jul 19 16:06:35 iPhone-JK eapolclient[14972] <Error>: Jul 19 16:06:35 SecTrustEvaluate [leaf ValidLeaf]
Jul 19 16:06:35 iPhone-JK eapolclient[14972] <Notice>: eaptls_handshake: SSLHandshake failed, errSSLPeerAccessDenied
Jul 19 16:06:35 iPhone-JK eapolclient[14972] <Notice>: en0 TLS: authentication failed with status 1001
Jul 19 16:06:35 iPhone-JK eapolclient[14972] <Notice>: en0 STOP
Jul 19 16:06:35 iPhone-JK wifid[14] <Error>: WiFi:[395935595.372837]: Failed to associate with AC: -369032215
Have anyone idea what should be a difference between ICU profile for MAC and iPhone/
Jerk55

Difference found A personal certificate in profile has expired while on Mac was renew.

Similar Messages

AMD CPU with Vista cannot connect to WLAN using MS-PEAP with WEP-128

We have a notebook "HP Pavilion tx1000 (AMD Turion64 CPU with Vista 32bits)". The notebook is using Broadcom 802.11a/b/g chipset, running AMD and Vista. It cannot associate to WLAN using MS-PEAP and WEP-128. Also, it cannot associate to PEAP and WPA2-AES.
The AP's log shows:
Oct 11 15:35:20 CCT: %DOT11-7-AUTH_FAILED: Station xxxx.xxx.xxxx Authentication failed
The ACS's log shows:
"EAP-TLS or PEAP authentication failed during SSL handshake"
We do not validate the certificate in the wireless setup. Vista's WLAN AutoConfig is used to configure the wireless profile. We are running Autonomous AP with Switch-Based WDS (WLSM).
We have no issue with Intel Centrino on the above authentication and encryption scheme.
Have checked the CCX program, broadcom 802.11a/b/g chipset is supported only for windows 2000 and xp. There is no mentioning about support for vista. Could this be a compatibility issue?
Please advise and thks

Maybe look at this post: http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=WLAN%20Radio%20Standards&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddf9be9/5#selected_message

Satellite A500-03P: Cannot connect to WLan using Win 7 + Event message

Hi all,
I very recently bought the Satellite A500 with the included offer of Windows7 when it was available end October 09.
So I got the DVD from Toshibe for the upgrade and followed the steps and upgraded from Visa home premium to Windows 7. I have two issues now.
1) I am getting a System Event Notification after start up, telling me about the system event log. The full message is below.
Failed to connect to a windows service
Windows could not connect to the System Event Notification Service service. This problem prevents limited users from logging on to the system. As an administrative user, you can review the System Event Log for details about why the service didn't respond
2) I was able to use this laptop for the internet PRIOR to the upgrade, both via a wireless USB drive as well at office via a modem ADSL.
Now I cannot access the internet after the Windows 7 upgarde!!
As an example the Optus dial up pop up box appears andwhen I click "connect" it does not connect.
Can anyone help please??
Thanks
C I

Hey buddy,
1)Have you checked the Service Configuration for this service? The start up type of System Event Notification Service must be always set to Automatic. This service is absolutely necessary for Windows and shouldnt be disabled or set to manual start type.
Check this!
2)To be honest I never heard about internet PRIOR but normally it should also be possible to access the Internet with Windows 7.
Make sure that the WLAN and/or LAN card is installed properly and check the TCP/IP settings. If you are missing some driver you can get it on the Toshiba page.

How to connect to wlan with n97 using ca certifica...

Hi all I have been trying to get my wireless working on my N97 at work which uses WPA/WPA2 and after a week and lots configuration changes I finally got it working, So I thougt I will share this
Since my work WLAN uses EAP-PEAP I needed the root ca certificate which i got from my network team.
So the first thing I did was send the cert to my phone and saved it
   To do this I sent the cert to my phone eg E:downloads folder
   I then went to file manger and found the cert under E:download folder
   I doubled clicked the folder and was promted to save which I did
   The cert will be installed under Setting-->Phone-->Phone Mangement-->Security     Settings-->Certf mangement -->Authority certificate
Next you need to setup a new access point to do this i did:
go to Settings-->Connectivity-->Destinations-->Access point(add new)
you will then be promted to auto check to available access points which you will click yes
select the wlan you like to connect to and select internet
After doing the above go to Settings-->Connectivity-->Destinations-->Internet-->your wireless network ....open this to edit
Connection name -- leave defautl
Data bearer --leave default
Wlan Network name -- leave default
Network status -- leave default
Wlan network mode --leave default
WLAN security mode -- WPA/WPA2
Homepage --leave default
user access point --leave defualt
the only thing to change is WLAN security setting to do this
Double click WLAN security setting
WPA/WPA2 -- EAP
WPA2 only mode --off
Double click EAP plugin settings
enable EAP-PEAP
disable the rest
Double click EAP-PEAP to edit
Pesonal certificate ---Not defined
Authority certificate -- click and select the on you saved in the begining
User name in user -- user selected
User name -- your user name
Realm in use -- user selected
Realm -- your domain
TLS privacy --off
Allow PEAPv0 -- Yes
Allow PEAPv1 --no
Allow PEAPv2 --no
click right with the key pad or press the right arrow on top
enable EAP-MSCHAPv2 and disable the rest
Double click EAP-MSCHAPv2
User name -- you user name
Prompt passsword -- YES
Password -- you password
After this go back to Setting -->conectivity-->WLAN network
search for you WLAN select it and it should work..
this configuration worked for me

Hi guys, got some problems with my n97 and the eduroam eap-peap with mschap v2.
so we got this thing new in university, and i'm not able to connect to it.
all the iphone/windows guys just connect to the wlanpoint, accept the certificate, enter their userdata (without a realm ..) and its on. as we all know, its not that easy with symbian (and android) mobiles.
I allways find the eduroam with full signal strength, and add an accesspoint with the right settings.
I searched about an hour and i am sure i got the right settings.
Connection name -- blablabla
Data bearer --wlan
Wlan Network name -- eduroam
Network status -- open
Wlan network mode --infrastructure
WLAN security mode -- 802.1x
Double click WLAN security setting
WPA/WPA2 -- EAP
eap-only and at pos.1
Pesonal certificate ---Not defined
Authority certificate -- the certificate i downloaded from university (same as on IPhone, PC..)
User name in user -- user selected
User name -- eighter username@domain and blank realm or only username and domain in the realm field
Realm in use -- user selected
Realm -- see username
TLS privacy --off
Allow PEAPv0 -- Yes
Allow PEAPv1 --no
Allow PEAPv2 --no
enabled EAP-MSCHAPv2 and disabled the rest
User name -- you user name
Prompt passsword -- YES
Password -- you password
So i can't connect to it, i try to connect to it and after a while it wants me to put my username and passwort in it (when i use prompt password yes of course). i enter it, enter the password. after a while it asks me a second time.. after i do it again it says
EAP-PEAP Authentification failed
For me, as a technical interested guy, it seems to me, that the logininformation is not correct or not transfered correctly. Why else should it ask me a second time to input it.
But i tried all possibilities, even with other domains ... other possibility, that my account is banned is not possible because i tried it with an other one an it didnt work too.
I dont have a clue why this doesnt work.. as said before, i really tried every username possibility (leave it blank, with domain, without...)
thats what we got from the IT-Guys (some information):
http://www.hs-heilbronn.de/1401508/wlan_eduroam_en.pdf
It would be great if anyone got some help for me =)
btw: sorry for my english, i am german as you can imagine when you look at the pdf file

When trying to update the i phone " fault 1630" occurs - both when connected to WLAN or USB. What can I do?

When trying to update my i phone IOS 5.0 (connected by WLAN and USB to my computer) there is always "fault 1630" saying I`ve got no connection to the internet / network, which seems to be wrong to me (phone is online). What can I do?

C Mawle wrote:
Thanks. I have followed all the instructions as recommended and nothing has worked so it looks like the restore/update may have been interrupted - would loss of internet connection do this?
Yes it would, possibly even brick it.
Have successfully connected my ipod nano with iTunes so looks like the device driver is working.
Can I use my ipod nano USB connector to check?
It is not much help to you, since the device that you need still not recognized.
Anyway looks like I may have to swallow the loss of data. Have set-up a call for tomorrow with Apple support so will wait until after this before doing the factory restore!
Good luck, but if you expect miracle from that call good luck again.

E72: Unable to connect to WLAN

Something weird is with my E72. I had been happily using the WLAN in my house for a few months now. Then yesterday it suddenly failed.
Unable to connect to the wlan. The default browser showed me "Unable to connect. WLAN not found" and "Unable to perform operation"
But during a WLAN scanning, I can clearly search my house WLAN showing me "2WIRE*** found".
E72 had really give me lots of problem. Hope this will be my last problem I encountered with my phone. Thank is advance for any suggestion for this problem.

Try with Hard Reset (shift+space+backspace+on/off). Make a full backup before!
Cheers
Einar

Nokia 5800 connected to WLAN but can't browse the ...

wassup! peeps.
recently I can't browse the web or use any free messaging apps such as Nimbuzz on my nokia 5800 (fw version 21.0) finland made, but clearly indicates that it's connected to WLAN...the ones I used before (in my home & @ my work).
I noticed it started when I was waiting for a video in youtube to finish buffering, then halfway to it it suddenly went back to my main screen. when i tried again, same thing happens. then i try to log-in to facebook or any website... first it will give the impression that its connecting but then, juz a couple of seconds or less, it willl suddenly revert back to my phone home screen.
this started a couple of weeks back, and now the bluetooth too is f***ed-up!
because my laptop can't see it, while yesterday it can.
it seems that mines the first one with this kind of problem bcoz i can't find any forum discussing this issue.
anyone who can help will be worshiped forever...thanx!
Solved!
Go to Solution.

You could also try to clean privacy data inside the browser, and reset your device by taking out the battery for a couple of min and set it back again.
Last resort: Soft reset it by dialling *#7370# (this will delete contacts, messages and everything else on C, so make a backup using PC suite) and do a format of the memorycard. - Then you start out with a fresh device.

N8 re-connect to wlan all the time.

I have search the forum and it seems that many people have the same problem. However I have not yet found a solution to the problem.
Widgets are set to offline. Datapacket is "only when needed".
Switch to wlan is "manual"
Data use in home country is "Always ask" . It connects without asking anyway!
Email is set up to sync every 30 min. This is not the issue.
I have social 1.2 installed but widgets are set to offline so it doesn't update.
The phone is ALLWAYS connected to wlan. If I tried to disconnect, it reconnects immediately. I can make it work by setting the phone to offline -> remove the access point (home network) -> put it back to online.
If I try to connect to home network via wlan guide now, it says "connection not available". However, if I restart the phone here then I can connect via wlan guide.
This will make the connection work properly. Email will connect when syncing and then disconnect again like it should.
If I restart the phone once more (now the home wlan connection is set up) then I will be back on square one. WLAN connected all the time I refuses to disconnect.
I would like to call this a proper BUG. This has nothing to do with setup.
Does anybody have a solution for this or do I have to wait until Nokia FIXES this?
I'm running PR1.2
regards
/Jens

I do have the wlan set to a higher priority than packet data. This is the way it should be I believe. I want it to connect via wlan first then packet data if no wlan is available.
I just tried to kill the "xmppservice.exe" process and this solves the problem. However this requires that I buy a 3rd party task manager. So this isn't really a solution. Also this needs to be done each time the phone reboots.
I also noticed that it is not just connected all the time but it is continuously sending data at slow rate.
The question here is really what does the xmppservice do I why does it work when shut down?
/Jens

N8 & Iplayer problem - connect to WLAN but I alrea...

All of a sudden I am unable to watch/download from BBC iPlayer. It tells me I have to connect to WLAN, which is fine, I always did this. But even when I am connected to WLAN I still get the same message so cannot use the iPlayer at all.
Think it may be a problem since the last upgrade.
I looked it up on the iPlayer website where it says to check the APN settings but like a large number of people I get 'sim card error' when I try to access the APN settings.
If someone can help before I completely give up on this awful phone I would be very grateful.

Check the settings under Menu/Settings/Application Settings/Videos Make sure that "Access point in use" is set to the WLAN you are connected to.

Number of connections over WLAN bridge?

I have a network that has been working flawlessly for many years but when I recently added a printer I ran into some problems. The printer is connected to a switch that is connected to an Airport Express that is connected over WLAN to an Airport Extreme. My problem is that I can only connect four devices to the switch. If I connect a fifth device it does not get an IP adress until I disconnect one of the other four devices. Please see the attached overview of the network. Red dotted lines represent wireless connections.
Any ideas about what causes this behavior is appreciated. Thank you.

on a jetpack or mi-fi 5 GB is nothing. Streaming Netflix can use 2.3 GB an HOUR. Even streaming YouTube in HD can use 1 or 2 GB per hour. I'm not sure why people think 5 GB is a lot for a regular internet connection. it's not. That why people should be using cable or DSL or fiber for internet

Connect c3 wlan configuration

plz help me co connect c3 wlan configuration plz help me a detail configuration
i have router and connect easy but internet not open

If you are experiencing that some of the apps in the C3-00 don't use WiFi even when you choose so to read this thread /t5/Cseries/nokia-c3-wlan/td-p/711188 it has some fixes that people have found useful.

Message "WLAN: Unable to connect. Wlan Network not...

Well guys i bought my nokia 5800 today so like any other curious people i looked the wi-fi hoping connect with the internet and when i try to connect with the wi-fi appears this message "WLAN: Unable to connect. Wlan Network not Found." and then it dosen´t connectbut he finds normally the networ and this message appears after i type the Router password.i´ve already looked in another foruns and i´ve already switch off the Option Qos in my router and the problem cotinues, so anyone can help me?my router is one linksys wrt54g and the type of connection is static ip an the security is Wpa Personal TKIP....
PLEASE ANYONE CAN HELP ME?I´D BE VERY GRATEFUL WITH THE SOLUTION FOR MY PROBLEM...
Thanks
Message Edited by darkcraft on 13-Jul-2009 09:47 PM

tomasvaril wrote:
Same To me. I have Asus WL-500W router at home, WPA2-PSK(AES), password similar to this "lIGf@91pY0TnFY!Jh@7LjTUlsL3ZPY", MAC address filtering. My old Nokia E51 works, my Touch Pro Works with it. When i try my one day old Nokia E72 it does not work, the same like others:WLAN: Unable to connect. Wlan Network not Found. E72 works at my work wifi, which has the same settings but without mac filtering. Have no idea what is happening, all is setting correctly. MAC address of E72 is allowed on router. It has the same settings like E51, but E51 works like a charm E72 does not work. What is wrong?
As already suggested, you could try disabling the MAC filtering from the router, just to outrule possibility of a typo while entering E72's MAC address to router settings.
Have you tried swithing a WLAN channel that your router uses?
Log in to your router's web management pages (check router's default IP address and username/password from it's manual) and switch of the "Automatic" channel selection mode. Try few different channels, like 1, 3, 6, 9, 11, if one of the channels happens to work any better. Note that in case you have set your router to use channels 12 or 13 (or in case "Automatic" channel selection mode has decided to select channel 12 or 13) you must have a SIM card inserted and some other than "Offline" profile enabled on your phone since Offline mode (i.e. airplane / flight mode) won't allow your phone to operate on higher channels than 11.
In case you have configured your WLAN network (SSID) to be "hidden", try disabling hidden SSID mode on the router.
Asus WL-500W router seems to be a pre-standard 802.11n device so might be worth looking in to your router's WLAN settings and see if playing around with router's WLAN operating mode and settings improve the situation. First of all ensure that your router is not set to operate in 20/40MHz mode (set it to 20MHz only) assuming that the router is in default 802.11b/g/n mode. You could also try disabling the 802.11n mode completely by selecting a 802.11b/g mode (if available).
You should probably also check that you're running latest (2.0.0.6 ??) firmware version on your Asus WL-500W router since there seems to plenty of complaints regarding WLAN connectivity and stability issues (in general, not specific to Nokia handsets) with this particular router model.

Connect to Wifi using LEAP in iOS 8.1

I was able to connect to wifi using LEAP (Lightweight Encryption Authentication Protocol) credentials with iOS 7.1 but as soon as I updated to iOS 8.1, I am not able to connect any more.
Did some R&D over this, got to know that Apple has explicitly disabled LEAP due to some security reasons.
Please comment if there is some solution or workaround to fix this issue.

Hi,
Have you test that other device could find this AD-Hoc network? You can try to recreate this network for test.
Based on my research, An ad hoc network is automatically deleted after all users disconnect from the network or when the person who set up the network disconnects and goes out of range of the other users of the network, unless you choose to make it a permanent
network when you create it. Therefore, please check whether you encountered similar situation.
I suspect that the error message means that the profile “MyNetwork2” doesn’t exist. Therefore, you may create the profile first.
To do this, please refer to the section “add profile” in the following document:
Netsh Commands for Wireless Local Area Network (WLAN) Preliminary]
http://technet.microsoft.com/en-us/library/cc755301.aspx#bkmk_wlanConn
Roger Lu
TechNet Community Support

Nokia C7 - Problem with VPN Connection over WLAN

Hello,
today I installed Nokia VPN Client 44.01(5) for Belle.
Before this update I used the following configuration: I set two SIP-profiles up and for each profile a own VPN-connection. One for connecting over radio and one for connecting over WLAN or hotspots.
So over all I had three kinds of connections or connection groups to choose: "Internet" with the radio and home wlan connections, "Intranet" for the VPN-connection over radio and "Intranet over WLAN" for VPN-connections over other WLANs.
The advantage of this configuration was that I could use the SIP-profile depending on my location and the phone had not to use the "standard" VPN-connection ("Intranet") over radio.
Now after the update I have the problem that I can't connect to my VPN over WLAN at all. Not with the SIP profile and not manually over the internet browser. There is always the notification "Connection Problem".
I tried also to put the "VPN over WLAN access point" from the "Intranet over WLAN"-group to the "Intranet"-group and gave it the first priority, but that doesn't helped too.
Does someone of you had or have the same kind of problem or otherwise has any clue about that?
Any help is very much appreciated!
Thank you in advance! I hope that I described my problem clearly.
Greetings
unsys

testing with the faceplate removed and into the master socket witha brand new filters result's below . I tried the quiet line test and it seems silent so no issues there. Can anyone see an issue, I've posted the noise results etc as well with the faceplate removed. (using a butter knife cause i'm just out of bed and tools are in the garage!)
0.7 Mbps
0 Mbps
1 Mbps Max Achievable Speed
Download speedachieved during the test was - 0.7 Mbps For your connection, the acceptable range of speeds is 0.2 Mbps-1 Mbps. Additional Information: Your DSL Connection Rate :1.06 Mbps(DOWN-STREAM), 0.45 Mbps(UP-STREAM) IP Profile for your line is - 0.75 Mbps
System Up Time 00:11:28
Port
Status
TxPkts
RxPkts
Collisions
Tx B/s
Rx B/s
Up Time
WAN
PPPoA
6657
9689
0
2806
19425
00:10:58
LAN
10M/100M
28652
22350
0
22356
5418
00:11:24
WLAN
11M/54M/300M
0
0
0
0
0
00:11:11
ADSL Link
Downstream
Upstream
Connection Speed
1056 kbps
448 kbps
Line Attenuation
49.0 db
27.0 db
Noise Margin
10.6 db
20.0 db

Satellite Pro M70: Cannot connect to WLan with ConfigFree

Hi in Forum.
I'm having trouble with a Satelite Pro M70, concerning gaining control of wireless conections.
When scanning with "The Radar" i ConfigFree for available wireless accesspoints, I get several points available, but is not able to connect to a single one of them. I can read their status and see their WEP encryption marker.
When I try to connect to any one of them, I get a pop up dialog box, which says (translated from danish) "Another suppliers software is in control of the wireless adapter". When trying to set up a connection through the classic windows way, windows states that "windows is not able to configure this wireless connection - if you have another program to administrate wireless connections you must use this". I suppose it refers to ConfigFree...?
Is the unnamed "other supplier" Windows related or maybe McAfee related (Security Suite 2007)?
If you're familiar with this problem or something like it I would be please to know.
By the way - where do I enter WEP encryption keys for my friends WLAN routers in ConfigFree?

> When trying to set up a connection through the classic windows way, windows states that "windows is not able to configure this wireless connection - if you have another program to administrate wireless connections you must use this". I suppose it refers to ConfigFree...?
It must be not a ConfigFree. Depending on you WLan card an Intel ProSet utility or a Atheros Client utility could controls the Wlan configuration!
Please check if one of the both tools controls the wlan and disable the function!
> where do I enter WEP encryption keys for my friends WLAN routers in ConfigFree
You should have three different tabs in the Configfree utility.
The second one Device settigns provides device list and there you should find Wireless network connection.
Choose it and use the button Network connections.
There you should find some encryption settings!
Please check also the Profile settings tab and the option called Security settings

Connect to wlan using eaptls

Similar Messages

Maybe you are looking for