Connect TV receiver and DVR receiver to network

Keep getting an error message when I try to view my recordings. It says I need to connect my TV receiver and DVR receiver to the network. How do I do that?

Your DVR (the TV receiver with the hard drive) and other TV receivers must all be connected to the Residential Gateway for them to function correctly.  The AT&T installer should have done this for you during installation.  Unless something has changed since then (moved one or more of them around, relocated some cables, unplugged the Residential Gateway), this should still be thie case.
 

Similar Messages

  • I am trying to connect my mac and PC through my network. the pc can seen and connect with the mac, but my mac can only see the pc it can't connect. how do i fix this?

    i am trying to connect my mac and PC through my network. the pc can seen and connect with the mac, but my mac can only see the pc it can't connect. how do i fix this?

    FORCE IPAD INTO RECOVERY MODE
    1. Turn off iPad
    2. Turn on computer and launch iTune (make sure you have the latest version of iTune)
    3. Plug USB cable into computer's USB port
    4. Hold Home button down and plug the other end of cable into docking port. Do not release button until you see picture of iTune and plug.
    5. Release Home button.
    ON COMPUTER
    6. iTune has detected iPad in recovery mode. You must restore this iPad before it can be used with iTune.
    7. Select "Restore iPad"...
    Note: Data will be lost

  • Connection between iPad2 and AV-Receiver via WLan

    I want to connect my iPad via WLan with my Onkyo AV-receiver to play music of my iPad. Do I need additional hardware or what have I to do?

    I don't think there is a one-cable solution either. You're going to need to feed the audio separately, and if the TV set doesn't allow you to select separate inputs for audio and video, then you won't be able to use the TV set's speakers at all. In that case, setting up a pair of computer speakers on either side of the TV is probably the best solution.

  • G5 No longer connecting to airport and other computers on network

    My G5 dual 2.0 (mid 1994) was connecting to the internet through airport extreme base station until Saturday. I had upgraded it to leopard (archive & Install) then up to 10.5.1 last week and all was good. After bootup today it doesn't see any other computers on the network and it doesn't get email and doesn't access the web. When I check network settings I notice that WPA Personal is selected but not WPA2, so I tried to change that but it didn't seem to change after applying after a restart. Then I checked to see if DHCP setting were configured. This is where things seem odd, I can't renew the DHCP lease like I can on my MacBook Pro (running current version of tiger) that I am typing this with. I tried to make a new airport connection, tried using a different account, checked system profiler (sees card and all), but no connection to email or internet. Is there a firewall configuration that I need to set differently? Also, verified permissions. Is there something else that needs to be done or is there a ugly bug stopping the show?

    i had the same problem after installing leopard on my macbook. it would not connect to the internet! i called applecare today and actually got someone who knew how to help me. he said that you have to reset the parameters whatever that means! and this is how you do it:
    1 - turn off your computer
    2 - turn on computer and immediately hold down these four buttons simultaneously: Option Key, Apple Key, P, R - then when you hear the second "ding" , LET GO OF THE FOUR BUTTONS.
    i did it and the macbook is connecting to the internet just fine. i hope this helps!!!!!!!!

  • Unable to connect mac laptops and windows laptops on network at same time

    Hi I have a wrt110 router which has a wired windows desktop attached. I also have several mac laptops connected wirelessly as well as an hp printer ,video game system blue ray player ,ipod,iphone and kindle all which connect with no problem. I have a pc laptop (Dell) which can see and connect to my network but does not  connect to the internet . I tried disabling and even temporarily removing the antivirus software plus disabling the firewall but with no success. I am at my wits end because I need the pc laptop for work. The internet will connect to the pc laptop when I hard connect it into the router.
    DSL through Earthlink .
    Any thoughts would be greatly appreciated.
    Solved!
    Go to Solution.

    Try this.  Disable IPv6 on all Win 7 computers under LAN properties for both wired and wireless adapters.  Reboot computers.  Leave the MAC's turned off for now.  Try to connect all the devices except the MAC's.  If successful connect the MAC's and if they have issue's, disable IPv6 on those now too.  Make sure the WRT110 on on firmware 1.0.04 or above.

  • Can't connect to Internet and 192.168.1 network at the same time

    I have been having an issue with my MacBook's networking for the past 4 months. Here are the specifics:
    *My MacBook is connected to the Internet via a linux router, with an address in the 192.168.1.x address space. DNS server is an openDns server, 208.67.222.222
    *My MacBook is assigned an IP Address manually in the 192.168.1.x namespace
    *I have a printer manually assigned an address in the 192.168.1.x namespace
    Problem:
    * I can only connect to my printer if I leave my DNS server entry blank under my Airport TCP/IP configuration
    * I can only connect to the Internet when my DNS server entry to set to the openDNS server entry.
    Question:
    Is there any way I can connect to both my local network printer and the Internet at the same time? I have set up two locations that I can switch between, but I would prefer to be able to access both networks at once.

    I tried turning AppleTalk on, but no luck.
    It seems that the problem is related to basic TCP/IP connectivity. For example, when my DNS server is set to blank, I get a fine response from the command "ping 192.168.1.253". However, when my DNS is set to one of the openDNS servers, I get this error:
    PING 192.168.1.253 (192.168.1.253): 56 data bytes
    ping: sendto: No route to host
    ping: sendto: Host is down

  • Connecting the internet and an already existing network

    I currently have a system set up using a 24 port linksys switch. All the computers go into this port including the server ran by windows 2000 server. I just recently got the internet at my business (T-1 Isp-XO) I have it set up where i just attatched a linksys wireless router to the modem and am using the internet on my laptop(put the info my isp told me to under static ip in the router i already tried dhcp or whatever that one that automatically obtains the ip is and it didnt work so static was required). What I would like to do is beable to hook up to the internet and the network on my laptop through the wireless router. I also have a wired linksys router 4 ports 1 uplink port if that would help at all to make this possible thx in advance Message Edited by Cantonwholesale on 06-20-2007 04:05 PM Message Edited by Cantonwholesale on 06-20-2007 04:08 PM
    Message Edited by Cantonwholesale on 06-20-2007 04:25 PM

    Ok basically i have a 24 port switch, I have all the computers in the business hooked into a port in the switch including the server which has a dhcp server which assigns all the computers an ip address. All these computers in the switch are in the same network. Now heres where I have encountered the problem i just recently got a T-1 internet connection. I have a laptop which i also just got so i hooked in a wireless router to the modem of this T-1 connection. The wireless router and switch at the moment are completely separate meaning the computers attached to the switch are apart of the network but not the internet. Now the router attached to the modem can only access the internet and thats it sense its not connected to the switch. What I want to do is be able to access the network and the internet at the same time through the wireless router. So I tried to take one of the open ports of the switch and put it into the 1st port of the wireless router. When i did this all i could still get was the internet. When i disconnected the wireless adaptor on my laptop and reconnected I got the network which all the computers connected into the switch get. So I called Linksys they told me that the problem was that the router and the server of the network were assigning ips so both couldnt work at the same time. This is where I am at right now I dont know how to fix this or even what to do they told me to turn off the dhcp on the router which i tried to do but the router stopped responding and i couldnt even connect to the router.

  • Regarding Accounts Payble and Accounts receivable in Tcode FB01

    Hi All,
    Can anybody tell me the diffrence between <b>Accounts payble and Accounts payble adjustable</b> in post document - FB01.
    Also tell me the diffrence between <b>Accounts receivable and Accounts receivable adjustable</b> in post document - FB01.
    Thanks in advance.
    Thanks & Regards,
    Rayeez.

    Hi Stuart,
    If you define the code from the G/L account determination screen then it automatically
    picks the code when add the new BP manually or through DTW.
    If you are not define code from the G/L account determination screen then you cannot add the
    BP manually or Through DTW it shown the error message.
    If you define the code from the G/L account determination screen then you want to
    change the code in accounting tab at the time of  BP added manually or through DTW
    you can change the code it will allow.
    *Close the thread if issue solved.
    Regards
    Jambulingam.P

  • Cannot connect to the iTunes Store. Make sure your network connection is active and try again

    I keep getting "iTunes could not connect tothe iTunes Store. Make sure your network connection is active and tryagain." My network is up and working. Why can't iTunes tell?

    Did you find a resolution as I'm having same problem?

  • Losing connection during call and get no reconnection for hours

    Hi, I use my iphone4 (not iphone 4S) with ISO5 latest version. Since some weeks during calls I lose connection to provider and cannot reconnect to network. Restarting doen't help. After some hours the iphone get again connection not knowing what has happend. Losing connection happens while I'm on a fixed place (not travelling in a car or something similar) and making a call. It also happens at different places. Vodafone changed my SIM-card but it doen't help. I also backed-up and renewed the the iphone-software by using iTunes. The vodafone-support explained that with renewing the software a new software-patch will also be installed that should help. As you can imagine - I still have the problem! Who can help?
    Thanks for answering!

    #1 Did the problem start occurring after any particular weather event?
    #2 What light turned/turns red?
    #3 Do you have Voice service, and if so, do you have noise or static on the line while in a call that was never there before?
    #4 Lastly, visit http://192.168.1.1/ and visit the System Status section of the ActionTec. Provide the Transceiver Statistics it shows.
    If you need a login, try the following:
    admin/password
    admin/password1
    admin/admin
    admin/admin1
    Your Verizon Username and Password
    If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

  • Received following error message "itunes could not connect  to the itunes store. make sure  your network is connection is active  and try again." i know the connection is active. what can i do to resolve?

    received following error message "itunes could not connect with Itune store - make sure  your network connection is active and try again" i know my connection is active. does anyone know how to fix this problem?

    Close your iTunes,
    Go to command Prompt -
    (Win 7/Vista) - START/ALL PROGRAMS/ACCESSORIES, right mouse click "Command Prompt", choose "Run as Administrator".
    (Win XP SP2 & above) - START/ALL PROGRAMS/ACCESSORIES/Command Prompt
    In the "Command Prompt" screen, type in
    netsh winsock reset
    Hit "ENTER" key
    Restart your computer.
    Now launch your iTunes and see if it is working now.

  • Upgrading to iso 5 and receiving error message "the network connection timed out" and won't complete the update.  How do I fix to complete the upgrade?

    Upgrading to iso 5 and received an error message "the network connection timed out" and fails to complete the upgrade.  How do I complete the upgrade?

    Try a manual install, as outlined in the link below.
    Basic troubleshooting steps  
    17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
    Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101
     In Memory of Steve Jobs 

  • When updating to iOS 5.0.1. get the err -3259, thus unable to install new iOS. The message I receive goes: "THE NETWORK CONNECTION TIMED OUT.  MAKE SURE YOUR NETWORK SETTINGS ARE CORRECT AND YOUR NETWORK CONNECTION IS ACTIVE, OR TRY AGAIN LATER."

    When updating to iOS 5.0.1. get the err -3259, thus unable to install new iOS. The message I receive goes: "THE NETWORK CONNECTION TIMED OUT.  MAKE SURE YOUR NETWORK SETTINGS ARE CORRECT AND YOUR NETWORK CONNECTION IS ACTIVE, OR TRY AGAIN LATER."
    Does anyone know how to solve this tiresome problem, please!?? The update is downloaded upto 723.5MB, and is required upto 723,6MB, then the error message pops out! Tnx.

    I have a quick wifi connection (Mac shows it as about 35 megabits) but I couldn't get the 5.0.1 OTA to work, I had to do it via cable to my computer's iTunes - and as I was already on iOS 5 it was only a small download, basically the same size as the OTA size.
    As the original poster is talking about a 730 meg download then I assume that they are still on iOS 4.3.5 or below and can therefore only download via their computer's iTunes - you need to be on iOS 5+ before you get the OTA option.

  • New (last night) 4s.  at home everything works but at the office, I can't seem to send or receive emails.  Don't know about texts yet.  I manually connected to my company's wi-fi network, have internet access and a good signal.  The phone function works

    Just set up my 4s last night - works fine at home but can't get or send email at the office.  Wi-fi connection working and signal is good and telephone and Internet functions working.  Manually set to my company's wi-fi. 

    Your company has most likely blocked the ports necessary to connect to mail servers outside the corporate network. Shut off WiFi and see if it works. If it does, you'll need to talk to your IT department about it.
    Odds are they are not going to change the policy without a valid business reason to do so.

  • I received this error: "iTunes could not connect to the iTunes Store. An unknown error occurred (-3212). Make sure your network connection is active and try again." We are connected. Any ideas on how to solve this?

    I downloaded iTunes. I was going to put an MP3 lecture on iTunes so I could put it on our new iPad but I got the message:
    "iTunes could not connect to the iTunes store. An unknown error occurred (-3212). Make sure your network connection is active and try again." I was able to get on this site so I know the connection is fine. Any ideas how to fix this?
    Thanks.

    Hello Buck
    If you are having issues with the iTunes store, check out the article below.
    Can't connect to the iTunes Store
    http://support.apple.com/kb/ts1368
    Thanks for using Apple Support Communities.
    Regards,
    -Norm G.

Maybe you are looking for