Connect via P2 Interface to WSA S160 for initial set-up

Currently have deployed WSA with the following interfaces:
1/ Management : 1.1.2.2/24
2/ P1 : 10.10.20.14/24 (inside DMZ interface for secure network)
3/ P2: 8.8.8.136/28 (Public DMZ interface)
Issue:
I can not reach Management interface on segment at this time to run set-up wizard for configuring the WSA.
I can reach and talk to P2 interface via ASA 5540 which controls all inbound traffic to WSA.
How can I remotely reach WSA via P2 to run setup wizard via GUI for WsA set-up?
I know I must use http://IP_ADS:8080/8443 but how can I get there via public IP Address or proxy.
Note: I have a proxy 5.5.5.5 which I have built acl on 5540 to allow tcp 8080/8443 to 8.8.8.136.

Setup wizard can only be access through the management interface(M1). At this moment the only choice will be to connect via console.
You may also connect directly to the unit's COM port using a null modem cable (9-pin serial) in order to establish a command line interface (CLI) session. This is particularly useful during the initial configuration process of the device. In order to proceed, you will need the following:
9-pin female-to-female serial cable (null modem)
Serial console client (such as HyperTerminal or PuTTY)
Please use the following procedure as a guide:
Connect your laptop (or other client device) to the serial port on the back of the unit using a standard 9-pin null modem cable.
Launch your preferred serial console client. Specify the appropriate COM port to use on your local machine, and use the following settings for the connection:
Bits per second: 9600
Data bits: 8
Parity: None
Stop bits: 1
Flow control: Hardware (RTS/CTS, DSR/DTR)
Once the session has been opened, you may need to press Enter to trigger output. At this time, you should see a login prompt akin to what would be seen in a Telnet- or SSH-based CLI session.
Log in using your appropriate credentials.
Thanks,
Tery Le Febvere

Similar Messages

N6705B connectivity via GPIB interface in UNIX

Hi
i had an N6705B device my requirement is like below
I need to control this device via an GPIB interface in linux PC.
for the above i am using an GPIB to GPIB cable and connected the N6705B and amy linux device.
Now i have to connect/login in to the N6705B device and do the settings like setting voltage for the DUT (IC chip) and collect measurement for various test scenarios of DUT.
For example i have to set the input voltage as 3.7v to my test device(which is an wifi device) and connect it to an access point(connection will be done manaully) so during the connection stage i have to measure the current consumed by the device (taken across power amplifer).
I think there are SCPI commands whcih i notice in the AGilent 14585 control software which do the same (the software support is there in windows 7 via an GUI), is there any posibility now this commands i can send to the agilent N6705B device by logging into it from a linux PC.
Thanks
Varun.P

Duplicate: http://forums.ni.com/t5/Instrument-Control-GPIB-Serial/SCPI-commands/m-p/2959241#M65332

Connect via RDP option is not enabled for some VM's on the same Hyper-V Host

Hi. I have many virtual machines on a Hyper-V host being managed via System Center Virtual Machine Manager 2012. When you right click on a virtual machine - Connect or View - Connect via Console is enabled, but Connect via RDP is not enabled for
most but not all of the machines. Is there a setting on the Hyper-V host that I need to modify to enable Connect via RDP for all of my VM's? All of the virtual machines have the same configuration meaning that Remote Desktop is enabled for all
of them on the OS itself.

Hi Debabrata,
In App Controller the console access is provided by an ActiveX control and this requires the client (web browser) to connect directly to the Hyper-V server. As you note, for this to work over the internet would require the Hyper-V host to be accessible from
the internet, and this is not a recommended security practice.
Publishing App Controller as a Remote App avoids needing to make the Hyper-V host accessible to the internet. I'm not an expert in setting up Remote App and don't have an answer about how to avoid doing 2 lots of authentication. The
Remote Desktop Services forum is likely to be a better place to ask a question on setting up Remote Apps.
Let me know what you need help with for the Remote Console in Windows Azure Pack option. There is also a forum for
Azure Pack and two of our MVPs who do have console connect working have both written articles that describe their experience.
http://kristiannese.blogspot.com/2014/02/configuring-remote-console-for-windows.html
http://www.hyper-v.nu/archives/mvaneijk/2014/01/windows-azure-pack-remote-console-with-the-rd-gateway-in-a-dmz/
Regards,
Richard
This posting is provided "AS IS" with no warranties, and confers no rights.

Connection via TAPI Interface

Hi,
Where could find the document <b>SAPphone Server 2.0 Usage of TAPI 2.1.</b>
I read about this in the document SAPphone - Telephony in SAP Systems, Interface Description but when I search the document I never can find it.
Best regards,
Ana Jimena Rodas.

Hi Paul,
Thanks for your help, I read about its company; you have all the complete solution and the Telephony Connector you are really good !!!
TAPI interfacing
I have the document SAPphone Telephony in SAP Systems - Version 5.11A9; and in page 17/87 it says The SAPphone Server supports TAPI Version 2.0 and later. A detailed description of the SAPphone server is contained in the document ´SAPphone Server 2.0 Usage of TAPI 2.1´and then I am looking this document.
What SAP product/release are you working with?
The actual characteristic of my system are:
- SAPphone RFC interface: 5.11ASP (Local architecture, Identification by host name of computer)
- SAPphone Server 2.5.9
- SAP CRM 3.0
- SAPGUI 6.40
- Microsoft TAPI 2.0
Is this for a small, medium, or large call center?
Im using Avaya IPOffice 403 with TAPI 2.0 in my contact center; it is like a medium contact center.
Paul, Could you help me with this question:
If I want to handle a call from SAP IC (WinClient or WebClient ), I could need something like a CTI connector between SAP Interaction Center and Avaya Phone Manager. Something different from the SAP Phone, for instance?
Best regards,
Ana Jimena Rodas.

Signing in to WebOS on my Pre 3 for initial set up

No device
I recently purchased a Pre 3 and have been unable to use it - it requires a WebOS sign in, but I get a "Sign In Failed" message each time I try. I have a valid SIM card in the phone but see "Network search..." on the phone. How do I get my phone to work?!
I have a Pre 2 which gave me none of these problems - in fact my webOS account still shows the details of the Pre 2 device.

No device
I recently purchased a Pre 3 and have been unable to use it - it requires a WebOS sign in, but I get a "Sign In Failed" message each time I try. I have a valid SIM card in the phone but see "Network search..." on the phone. How do I get my phone to work?!
I have a Pre 2 which gave me none of these problems - in fact my webOS account still shows the details of the Pre 2 device.

WSA S160 Support for Terminal Servers (How are terminal server connections handled?)

We have a terminal server environment with a mixture of computers and laptops. Currently we have multiple proxy servers and would like to considate down to one. Our current solution does not work well in a terminal server environment. We are looking for a way to integrate all equipment with one soluton and I was curious as to how the S160 handled users connecting via a terminal server.

Edadios thanks for the response. I was reading over this document (see attached), and it looks to me like the connection would be tracked via a cookie surrogate. My bigger concern is that we are looking to be able to track usage per user even though they are on a terminal server. Our current solution (Barracuda) is not able to perform this function. I am hoping to have a S160 on site this week to do some testing but was hoping to gather some intel in the forums prior to implementation.
The response helps clear up what protocols are in use but I am still wondering how terminal server connections are handled by the WSA and if they are truly handled and tracked per user instead of by the device they are connecing to.

CO 1SRJ-001: Too many line items selected via report interface

Report group/report 1SRJ/1SRJ-001 (CCentres: Rolling Year): provides an overview for the last 12 periods of actual and plan data.
When you access line item report RKAEP000 (KSB1 or KSBP) from report Cost Centres Rolling Year (1SRJ-001) using the report/report interface, too much data is selected.
For example, you enter fiscal year 2009 and month 8 in selection parameters, the report generates results for the last 12 periods: 2008/9 to 2009/8. But the line item report accessed via report interface selected ALL data for the fiscal years 2008 and 2009.
I searched and found Note 127643 that described a similar but not exactly the same situation. Have anyone have any problems with this report? Any suggestion is appreicated.
Regards,

Issue with report 1SRJ-001 (S_ALR_87013631) has been resolved. The interfaced line item report selects all data records for fiscal years 2008 and 2009, instead of just for the selected last 12 months. The problem is due to missing restrictions for a characteristic, in this case, the from-period and to-period fields.
SAP has corrected the problem by issuing an updated version (1999) and the one we were using was the 1995 version. I imported the updated version of report from client 000 and now it works fine.

HT4628 After installing the new OS from apple (10.8.2) my macbook pro keeps disconnecting from the internet. I am connecting with an Airport Extreme and while it shows I am connected, every 20-45 seconds its searching for a wireless connection. Any sugg

I guess I posted my question as a title but that is my issue. My airport is connected via wireless yet it keeps searching for a wireless connection, hence I am experiencing bad latency and disconnection issues. Anyone know a solution?

I have the same problem. And in my case it happens when i transfer "large" files over the WiFi. When i send an MP3 filer over Skype i loose connection. When i transfer updates between my iPhone 5 / iPad 3 and iMac with Mountain Lion i loose connection. When i have a video conference i loose connection. You get the idea.
There is usually like 30 people using their own router on the 2.4 GHz band near by. None on the 5 GHz band which i use. But when my WiFi freezes on ML i can only see my own router. And i am also connected to it. But all my neighbors WiFi routers are now invisble to me. My network stalled.
What i do is that i disconnect my WiFi and then reconnect it again. Thank fixes it. But all my transfers and what not has been dropped. And i have to start all over - and the WiFi will stall again.
While my WiFi is frozen on the iMac with ML i have no problem using the same router on the same 5 GHz band with my iPhone 5 or iPad 3.
Downgrading the AirPort Extreme to 7.6.1 from 7.6.3 helped a bit. Now i only loose connection a few times each day.
It is a software error in ML i am sure of. A driver maybe. But i am suspecting that it is either a speed-sync error or an energy saving error. Like the network card turns of in the middle of a file transfer to save enrgy - maybe.
When i stream movies from my iMac to my Apple TV or 3 there is no problem at all. It is so odd.

Connection problems with ESA C160 and WSA S160

currently I have deployed ESA C160 and WSA S160 devices in a network but I cannot remotely connect to the devices.
I have installed Cisco 2811 Terminal server with octal cable connections and cannot seem to get terminal access.
As well I have connected the Management Interface to a local switch and provisioned VLANs on subnet 192.168.42.X to allow for access but no connection seems to work to gain access to the devices.
I am wondering if there is a specific cable configuration or connection which will allow me access to the applicances for configuration.
Any help is appreciated!

HI
Are you attempting a remote connection to the serial ports via 2811? I may be missunderstanding your post.
The serial ports are 9600 Baud 8N1. Typically you will use a null modem cable for the connection.
For the network you should be able to connect to the manamgement interface SSH and HTTPS should be enabled by default. If you connect directly to this port using a crossover cable can you establish a connection?
If the network connection is failing I would first start with the serial port so you can verify that the configuration is as you expect it to be, meaning the IP address and services enabled. If everything checks out in the configuration. I would next test using a crossover cable on the same subnet. If that works then I would connect the appliance to a switch and test from there. The biggest questions that come up are can you route to the appliance over the network and can you resolve the host over the network.
Christopher C Smith
CSE
Cisco IronPort Customer Support

Problems connecting two Macpro via ethernet while airport is on for interne

I have two Macpro connected via ethernet. To make this connection work I have to go to system preferences/network and put ethernet the first in the list of "connectivity systems". As airport goes to the second place in the list I loose internet connection via airport. Is there any way of keep the two connections at the same time? It seems that only the first in the list works properly.
Thank you.

Mondotropo Hola, y una cálida bienvenida a los foros!
The Interface that connects to the Internet, (Airport in your case), needs to be dragged to the top of Network>Show:>Network Port Configurations and checked ON.
Local networking should use Ethernet below that... OSX tries the top one for Internet.
La interfaz que se conecta a Internet, (el aeropuerto en su caso), debe ser arrastrado a la parte superior de la Red> Mostrar:> el puerto Ethernet y comprobarse.
La creación de redes locales deben utilizar Ethernet debajo de ese ... OSX trata de la parte superior para Internet.

Gilson 307 pump which are connected via a system interface module 506C

hello,
I have a master's thesis received the task to control gilson pumps.
Unfortunately I have no experience with LabView.
It is generally possible to steer the pump? I read a lot and it will describe this is not possible. But I have a compoliertes Pogramm and unfortunately can not get the source code and the driver. There you can control the pumps.
Can one of you help. I would be very grateful.
hardware:
three Gilson 307 which are connected via a system interface module 506C. The interface module is connected via an RS232 connection.
LabView 2012
Thank you very much in advance and best regards
Michael

Thanks for the extra comments GerdW.
Perhaps there is someone who wants to help me, in the manual are not the commands available. Even the technicians of Gilson I could not tell from his documentation of the command sets.
many greetings
Michael

How can I transfer photos from LG phone to mac notebook. Phone appears in iPhoto when connected via USB but selection for download shows 0 photos

How can I transfer photos from LG phone to mac notebook. Phone appears in iPhoto when connected via USB but selection for download shows 0 photos

Just open your LG volume up likes its an external HD and drag all photos onto a folder in your macbook Air.

Iphone 4S updated to iOS 5.0.1 last nite no longer visible in iTunes for wireless sync. check box is viewable as checked when connected via usb. anyone else having this problem and been able to sort? Thanks.

Hi all. Update my iphone 4S via usb last night. Since then the iphone is not visible in itunes for wireless syncing. The sync wirelessly box is checked and is viewable as checked when phone connected via usb. Anyone else have this problem and been able to sort? Thanks. Doug

Hi all. Update my iphone 4S via usb last night. Since then the iphone is not visible in itunes for wireless syncing. The sync wirelessly box is checked and is viewable as checked when phone connected via usb. Anyone else have this problem and been able to sort? Thanks. Doug

After installing Mountain Lion on my 17" MBP G-RAID mini connected via Tempo SATA Edge ExpressCard34 is no longer recognized. I restored icon and access by removing 34 card and substituting FW800 for eSATA. Any fix for the higher speed connection? TIA

After installing Mountain Lion on my 17" MBP G-RAID mini connected via Tempo SATA Edge ExpressCard34 is no longer recognized. I restored icon and access by removing 34 card and substituting FW800 for eSATA. Any fix for the higher speed connection? TIA

Looks like the Silicon Image drivers were moved to the incompatible software folder during install/upgrade.
Downloaded latest drivers, errored out of install claiming that the drivers were from an unknown author!!!
Emailed their tech support this evening describing problem.

Mac OS 10.5 Bonjour Unable to find printer driver for P1606dn connected via wired network.

I have been trying to connect my HP Laserjet Pro P1606dn to my PowerMac G5 running Mac OS 10.5.8. I connected the priner to my LAN via Ethernet cables and NetGear 8-port switch. I then successfully installed the printer driver from the supplied CD on the Mac and went to System Preferences / Print & Fax to add the printer to the list of connected printers. Hit the "+" button. The HP P106dn was listed in the table (Kind = Bonjour).
I selected this entry in the table, and the dialog box immediately went into action: the "Print Using" pullodwn listed the greyed out message "Please select a driver or printer model" and a spinning wheel labeled "Searching for new drivers" appeared below it. The dialog box searches for but never finds the printer driver (I waited 20 minutes with no success). I have installed other HP printers this way on this machine without any problem, e.g., HP Color Laserjet 2605dn. Why is this method not working with this printer?
I was able to connect this printer with other (Intel) Macs in my household via this LAN arrangement. Is the printer driver for Intel-only Macs?
I disconnecting the printer from the LAN and connected it directly to my Mac with a USB cable. Followed the same process, and I was able to connect to this printer. Successfully printed a document page. While this provides me with a work-around for the G5 Mac, I need to share this printer with the other Macs in my household.
I went to the HP download site and downloaded the latest driver for this printer, re-installed the printer driver on the Mac, and repeated the steps for the LAN arrangement (above) to complete the connection via the Print & Fax dialog. The result was the same: spinning wheel searching for a printer driver that it cannot find.
I do not know what else to do, or why this installation will not work. I would appreciate it very much if anyone could offer an explanation for this or some suggestions as to what else can be done?
Ed
This question was solved.
View Solution.

I apologize for the delay in responding to you. I was on the road all day yesterday.
OK. I switched the printer's Ethernet cable to a Linksys Switch (Model EZX S55W) that's part of this local network. That did not work. I swapped out the cable for one that I know works. Still no change. I switched the printer's Ethernet cable directly to a port on the router. No change. I even swapped cables here, too, but no success.
As I was doing all this, I was wondering: When I select the HP P1606dn printer in the Print and Fax "Add" dialog box, (see the image below) and the Print Using pulldown menu displays "Please select a driver or printer model" and the message "Searching for new drivers" appears under it (with the spinning wheel), why is it that the Ethernet connection to printer is critical to "finding" a new (printer) driver?
Isn't the utility searching through my system and libraries looking for a printer driver app for the printer that I identified/selected in the dialog box?
After all, if the dialog box lists the printer among those to choose from, hasn't the utility already discovered the printer via the Ethernet connection?

Connect via P2 Interface to WSA S160 for initial set-up

Similar Messages

Maybe you are looking for