Connected, yet not connected?

ISP: Windstream
Router: Linksys WRT54G2
Laptop: HP Pavilion (Vista SP1)
I have a fiberoptic connection. So no modem, the desktop is hard-wired to the Linksys router. The desktop connects fine, I have no trouble there; the laptop was the same way, until yesterday, it just went dead on me. It says successful connection, yet I am not able to browse the internet.
I was on the phone with HP, Windstream & even Linksys and I did everything they asked. The cause might be something simple, but so far it seems too complicated to figure out, let alone fix.
A list of things I have already attempted:
*I have disabled IPv6, only IPv4 is enabled.
*I reset the router multiple times
*I also tried to change the ip to 10.10.10.1 in the Linksys Setup
*I tried did the DhcpConnBcastFlag fix
Below are the nbtstat & IPCONFIG for Desktop (hardwired) & Linksys (Wireless, while connected to the network)
Local Area Connection:
Node IpAddress: [192.168.1.100] Scope Id: []
NetBIOS Local Name Table
Name Type Status
RAGHUVEER <00> UNIQUE Registered
RAGHUVEER <20> UNIQUE Registered
DESKTOP <00> GROUP Registered
DESKTOP <1E> GROUP Registered DESKTOP <1D> UNIQUE Registered
..__MSBROWSE__.<01> GROUP Registered
ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : RaGHUVeeR
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Realtek RTL8139/810x Family Fast Ethernet NIC
Physical Address. . . . . . . . . : 00-11-2F-1C-83-59
Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 192.168.1.100
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.1
DHCP Server . . . . . . . . . . . : 192.168.1.1
DNS Servers . . . . . . . . . . . : 192.168.1.1
Lease Obtained. . . . . . . . . . : Thursday, November 13, 2008 2:33:25PM
Lease Expires . . . . . . . . . . : Friday, November 14, 2008 2:33:25 PM
PPP adapter Windstream:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : WAN (PPP/SLIP) Interface
Physical Address. . . . . . . . . : 00-53-45-00-00-00
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 98.20.77.213
Subnet Mask . . . . . . . . . . . : 255.255.255.255
Default Gateway . . . . . . . . . : 98.20.77.213
DNS Servers . . . . . . . . . . . : 166.102.165.11
166.102.165.13
NetBIOS over Tcpip. . . . . . . . : Disabled
((Now the laptop))
Local Area Connection:
Node IpAddress: [0.0.0.0] Scope Id: []
No names in cache
Wireless Network Connection:
Node IpAddress: [192.168.1.102] Scope Id: []
NetBIOS Local Name Table
Name Type Status
LAPTOP <00> UNIQUE Registered
WORKGROUP <00> GROUP Registered
WORKGROUP <1E> GROUP Registered
WORKGROUP <1D> UNIQUE Registered
..__MSBROWSE__.<01> GROUP Registered
ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Laptop
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
Ethernet adapter Local Area Connection:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : NVIDIA nForce Networking Controller
Physical Address. . . . . . . . . : 00-1D-72-5E-7F-B2
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Wireless LAN adapter Wireless Network Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Broadcom 802.11b/g WLAN
Physical Address. . . . . . . . . : 00-21-00-26-AA-10
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IPv4 Address. . . . . . . . . . . : 192.168.1.102(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : Thursday, November 13, 2008 12:46:46 PM
Lease Expires . . . . . . . . . . : Friday, November 14, 2008 12:46:46 PM
Default Gateway . . . . . . . . . : 192.168.1.1
DNS Servers . . . . . . . . . . . : 192.168.1.1
NetBIOS over Tcpip. . . . . . . . : Enabled
Tunnel adapter Local Area Connection* 7:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : isatap.{EFFD3AB7-3199-43DB-863A-36666D23B
A33}
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 6:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : isatap.{D07B0651-BF9C-4166-AFB1-5E1ABEC8B
B9D}
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 16:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : 6TO4 Adapter
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Help from here is my last hope, and honestly, ANY help is appreciated.

Remove the prefered networks from wireless computer and try to reconnect to the network .

Similar Messages

Frustration: Airport connected yet not *connecting*

My airport recognizes its apple network and registers four full bars in the airport icon, and yet, try as it might, it still can't/won't connect to the internet. I'm not sure what to do. It's happened before and fixed itself--or perhaps I did something to make it work and now I've forgotten what it was. In any case, any help would be much appreciated. Thanks.
(I've installed the latest airport software, too.)

Try turning airport off then on again from the menu bar and see if it reconnects. I suspect it will.
If so, I suspect you're running 10.5.2 or 10.5.3. And unfortunately there's no definitive fix, but a lot of people suffering.
Check this thread:
http://discussions.apple.com/thread.jspa?threadID=1397364&start=60&tstart=0
A lot of the possible fixes (that seem to have worked for some) are mentioned. But none are guaranteed.

I have MacBookpro with OSX 10.9, and my Tata Photon plus is not working on it. When I try to connect, Its not connecting.. Please Help

I have a MacBookPro with OSX 10.9, and my Tata Photon plus is not working on it. When I try to connect, Its not connecting.. Please Help
<Email Edited by Host>

Current Firefox versions require a Mac with an Intel processor and OS X 10.6 (Firefox 16 runs on Intel Mac OS X 10.5).
*http://www.mozilla.org/firefox/25.0/system-requirements/
For an unofficial Firefox 17.0.10 ESR compatible version that runs on a PowerPC Mac with OS X 10.4.11 or OS X 10.5.8 you can look at TenFourFox.
*http://www.floodgap.com/software/tenfourfox/
*http://www.macupdate.com/app/mac/37761/tenfourfox
*http://code.google.com/p/tenfourfox/wiki/ReleaseNotes1710
See also:
*http://code.google.com/p/tenfourfox/wiki/PluginsNoLongerSupported
*http://code.google.com/p/tenfourfox/wiki/QuickTimeEnabler
*http://code.google.com/p/tenfourfox/wiki/AAATheFAQ

My itunes on a windows 7 pc with dsl connection will not connect with the itunes store

my itunes on a windows 7 pc with dsl connection will not connect with the itunes store. Any suggestions about why not or how to get it to connect?

After reading the whole post, I still don't capture the exact error message or code from it when you failed to install Office 2013.
The only clue is that "bootstrap loader error" ...
It seems that you want to upgrade Office 2007 to new Office 2013, by default, we could complete the uninstall previous Office version and install the new Office in the installation wizard.
At this point, if you get the install source through CD or other media. I recommand that we copy/paste the installation to local drive. Then turn off all of anti-virus and firewall, begin to setup in
Windows clean boot mode.
Please use a setup log to troubleshoot setup problems in Office if the installation problem still occurs.
http://support.microsoft.com/kb/826511/en-us
Tony Chen
TechNet Community Support

Wifi says unable to connect, will not connect to any connections.

Wifi says unable to connect, will not connect to any connections. I cannot connect to any WiFi. Using iOS 6.0.1

The links provided work for iPod and iPhone!
Products Affected
iPad, iPhone, iPod touch, iTunes
You'll have to visit an Apple Store next to your place to get it looked at or contact Apple to get it serviced.
Apple - Support - iPod - Repair pricing

My iPhone connects to a hotel network but my iPad3 while it shows connected will not connect to the Internet.

My iPhone connects to a hotel network but my iPad3 while it shows connected will not connect to the Internet.

Welcome to the support community group.
First, are you sure that your AirPort Extreme has been configured correctly and is properly connected to your modem?
Begin by telling us how you have things connected and if the Airport Extreme is replacing a previously owned router or is this an entirely new installation?
First be sure that your modem is working and properly connects you to the internet using an ethernet cable directly connected to your laptop. Once you're sure that's working, reset the AirPort to factory defaults by disconnecting it from power and pressing and holding in the small reset button on the back for 15 - 20 seconds while you reconnect it to power. Then turn everything off for 5 minutes. Connect the Airport to your modem with and ethernet cable to the Airport WAN port on the back (check the user guide to make sure you connect the cable to the correct port) then connect a second ethernet cable between the laptop and one of the LAN ports on the AirPort Extreme.
Then power up the modem first, wait 5 minutes and then power up the Airport, wait 5 minutes and finally power up your laptop.
Then run the airport configuration utility from your laptop. Since you're not using an Apple computer, be sure that all of your firewall, and virus blocking and checking software is disabled before you run the airport configuration utility. Once you run the utility, it should detect your AirPort and allow you to use the configuration wizard to set things up.
Check back if you're still having problems.

Got 3G coverage yet not connecting to web

My Iphone 4 has stopped connecting to the internet but I have got 3G coverage. The loading cirle moves as normal yet the page doesn't load and a message comes up ; cannot open page - safari cannot open the page because it is not connected to the internet.
I have went through all the setting i.e full reset on my phone with no joy.
Is it because I have not updated my software since I got the phone a month ago for it's still got versio 4.3.3.?

1) If you have updated OVI Maps application to v3.06 this uses a different set of maps to those preinstalled on mass memory for v3.04. You may need to delete E:\CITIES + .qf file usually at bottom of list if using File Manager in Office folder, re-start OVI Maps application to re-initialise and re-define necessary folder structure to download more maps with OVI Suite > Maps on PC
3) and 4) probably related as settings sent by Tesco and saved by you end up in wrong destination (Uncategorised). Go to Menu > Settings > Connectivity > Settings > Destinations > Uncategorised - you'll probably find Tesco WAP, Tesco WAP GPRS and Tesco MMS here. If you longpress on any access point a new screen with more choices pops up, for Tesco WAP and Tesco WAP GPRS choose Internet destination. Now go to Internet destnations and probably need your WLAN as Priority 1 and Tesco WAP GPRS as Priority 2 for starters. For this highlight access point > longpress >choose "Change priority" and then highlight say access point in Priority 1 > OK and it jumps up the list.
When you open web browser click "Options > General > Access point > change to "Ask when needed" and next time you can change it to say "Internet" where home WLAN is Priority 1.
Post again when you are a bit more familiar with this as probably then have more questions.
Happy to have helped forum with a Support Ratio = 42.5

LELA Not Detecting an Internet Connection, yet is connected?

I use a WRT54GS wireless router, and recently it's been going slow. I went to go restart the router as we had to so many times before, and realized that the internet was not connected(or at least, that's what it said). So I figured, oh, that's why it's not working! After going through the restart process 3 times, I still couldn't connect. I looked down at my taskbar and it said that I had an internet connection. So I clicked on Internet Explorer and to my surprise I was indeed connected to the internet.
So now, I sit here typing this, on the computer which is supposed to have no internet, and cannot send an internet connection to any of my other wireless devices because LELA says I have none. I've tried reseting the modem and all that, but to no avail. Any help as to why this is?

Thank you very much jscell and Dr. Clap
No, because that is a conceptual rather than a realconcept<
I tend to disagree somewhat � it is a conceptual as
well as a very real concept. I am using this concept
and it works(still in the trial phase though). The
only problem is the pop-up Windows dialog box.Yes but you computer doesn't connect to the "internet". It connects to another computer. That is all it can do because that is how IP works (tunneled or not.)
>
If you want to monitor traffic via java then youwould have to use JNI.<
Thanks for this. I�ll have a look at this. A piece of
code to get me started on this would be appreciated.I am not sure it exists. But if you want you can look at http://netresearch.ics.uci.edu/kfujii/jpcap/doc/index.html
>
And you should be able to configure it so that itdoesn't ask you, but just automatically makes the
connection. How?<
Yes Dr. Clap, you may be right. I was hoping there was
somehow a way out without fiddling around with the
property settings. I am sure there is, but not in java. So doing it in java would require JNI (and a lot of digging to figure out how to do it using the windows C API.)

47TL515U Internet -- Connected or not connected, that is the question

   I just bought a 47 TL515U. I am experiencing problems setting up the (wireless) network. I followed the Easy Setup using PBC, Page 63, and got the message that the setup succeeded.
   However, when I click on Netflix, the Netflix page screen shows the message that I am, "Not connected to the Internet."
   I am able to confirm the settings configured in Wireless Setup using the Wireless Information procedure on Page 64. The Status shows as "Connected", Signal Strong, with all of the other information coinciding with my wireless network. So everything here appears that I have completed network setup and am connected.
Yet, when I perform the Network Connection Test on Page 66, sure enough, I receive the message, "Unable to complete network connection. Please check your network settings."
   I have an n router, I am successfully connected to my wireless network with my laptop computer, and have had absolutely no connection issues there.
   What shall I do next ?

Thanks for your reply, Peter,
I have now connected TV to router with network cable; I can connect this way. To make another attempt at connecting wirelessly, I have also now done the Easy Setup using PIN, entering that PIN to my router. My router thinks I am now wirelessly connected. Would that it were so; as before, the Network Connection Test tells me that I am not connected..
So I have now performed Wireless Setup:
   Easy Setup using PBC
   Easy Setup using PIN
   Assisted Setup
   Manual Setup
   IP Adress Setup (Manual)
   DNS Setup (Manual)
When I go to Wireless Information, the Status shows connected. It also shows Authentication as WPA2-PSK and Encryption as AES (even though, in Manual Setup, it said it couldn't connect because those 2 items were incorrect).

MSN Dial-up connection will not connect

Hello,
I just purchased an iMac with Mac OS X operating system. On my old computer I had an MSN dial-up connection and have tried to use this same internet connection on my new mac but for some reason the MSN will not connect. I tried a different dial-up service which did work, but need the MSN to connect. Any suggestions on how to get it to connect? Thank you!

Welcome to Apple Discussions!
Why do you need MSN to connect?
MSN Mail is usually over Hotmail, which Mac OS X Mail can pickup using
http://sourceforge.net/projects/httpmail-plugin
MSN Chat is available here:
http://www.microsoft.com/mac/default.aspx?pid=msnmessenger
You may need http://www.allume.com/ 's Stuffit Expander to extract that file.
Is there any other service you can't get?

Connected or not connected: iMac and iPad airport utilities disagree

The airport utility on my iMac show that my airport extreme is connected to the internet, and so it is, it works fine.
but:
The airport utility on my iPad show that my airport extreme is NOT connected to the internet, and yes, I cannot log onto my wireless network from my iPad. I find the network in the list of available networks, but when I log on it just hangs, and hangs forever. (But it easily logs onto any other network outside my home).
This happened after I bought a new iMac and connected to the net, there was some problem that it resolved by itself, but after that ny iPad disconnected.
I have upgraded everything that can be upgraded, restarted everything a number of times but still have the problem.
Please HELP, I miss my iPad!
Anneli

Try this:
1. Turn router off for 30 seconds and on again
2. Settings>General>Reset>Reset Network Settings

Airport has network connection but not connecting to Internet

I have a new Mac book pro, and am having trouble connecting to the internet on my home network.
I can connect to our wireless network and get 100% signal. But the internet is not connecting.
Using ethernet, I can get a connection and browse the internet and network. Using ethernet, the mac book pro has an IP address: 192.168.1.4
My router has an IP address of 192.168.1.1
The subnet Mask is 255.255.255.0
Using the Airport and DHCP I get very different results:
mac book pro IP: 169.254.17.98
subnet mask: 255.255.0.0
I have tried to manually input the IP, Subnet mask and router IP that work. But still no internet.
I can see lots of similar posts but no real answers to this.
If anyone can help, that would be great!
Cheers

If your wireless network is encrypted (WEP or WPA), try temporarily disabling encryption. Can your MBP get an IP address from DHCP and access the Internet wirelessly now?
If not, let's double-check your MBP's AirPort settings ...
System Preferences > Network > AirPort
o Location: Automatic
o In the left column, verify that an AirPort option exists. If it does not, click "+" to create one. (Note: If you are unable to create an AirPort configuration, the AirPort card in your computer either doesn't exist or it is not recognized.)
o Verify that AirPort is "On." Click "Turn AirPort On" button if not.
o Ask to join new networks: (enabled)
o Show AirPort status in menu bar: (enabled)
Systems Preferences > Network > AirPort > Advanced
AirPort tab
o Remember any network this computer has joined: (enabled)
o Disconnect from wireless networks when logging out: (enabled)
o Require Administrator password to control AirPort: (disabled)
TCP/IP tab
o Configure IPv4: Using DHCP
o Configure IPv6: Off
DNS tab
o DNS Servers: <if required, add your desired DNS server IP address(es) here>
o Search Domains: <if required, add your desired DNS Search Domain(s) here>
WINS tab
o Enter desired WINS info or leave the defaults
AppleTalk tab
o Make AppleTalk Active: (disabled)
802.11X tab
o Enter desired 802.11X info or leave the defaults
Proxies tab
o Enter the desired Proxies info or leave the defaults

How to unlock ipod not connected will not connect to itunes

how to unlock ipod not connecting to itunes

Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings

Two T61's - connected, yet not resolving - other computers do

Hello All,
We have two identical T61's that suddenly stopped (even though connected to the wireless router both wirelessly and hard wired) resolving to anything on the Internet, including email client activity, etc. Anoher older R52, which I am sending this on is connected the same way and works fine - any ideas?
H. Amina

Hi hamina, welcome to the Lenovo user forums!
To help you with this one the community will need a bit more information.
For example, tell us what you see when they are "stopped", the OS you are using, machine type, whether you are using Access Connections or a firewall, and any other information you think might be relevant.
I don't work for Lenovo. I'm a crazy volunteer!

Connected or not connected that is the question

I have had 4g for two weeks now and nothing but problems. When connecting through VZA Manager it will show connected but I have no internet. DNS will resolve fine but unable to ping and of course connect to anything. Why show connected if its not getting out???
Sometime hitting disconnect and connecting back will fix the issue other times its a good 15 to 20 mins before connecting. Once Im connecting It works great! Great speed ping for what 10 15 mins before the hole process starts over.     I am wishing I researched a little more before upgrading the two unlimited 3g devices I had. Very disappointed !!

I have windows 7 Enterprise
1st I do not see Activation under options. Ive not seen that since we got the 4g card and i updated the VZ access manager
2nd   I tried to delete the connection but I still connect to the networks that do not work
3rd    OMG did creating the apn screw my card up after connecting it lasted about 15 secs and still grabbed the network that is not working for me. When i went back to VZ manager 4g would drop and 3g would come up card would power off and started getting wmc604 error .
The APN setup added the (+CGDCONT: 5,"IP","vzwadmin","0.0.0.0",0,0) and removed the
+CGDCONT: 1,"IPV6","vzwims","0:0:0:0:0:0:0:0",0,0 and some how the moble ip turned to off.   I was able to get the ipv6 added back but still have an extra . Im not sure how to remove the 5th. Any ideas?
+CGDCONT: 1,"IPV6","vzwims","0:0:0:0:0:0:0:0",0,0
+CGDCONT: 2,"IPV4V6","vzwadmin","0.0.0.0",0,0
+CGDCONT: 3,"IPV4V6","vzwinternet","0.0.0.0",0,0
+CGDCONT: 4,"IPV4V6","vzwapp","0.0.0.0",0,0
+CGDCONT: 5,"IP","vzwadmin","0.0.0.0",0,0
4th The NDIS also grabbed the lower networks that are not working for me
Thanks for the Ideas.   I do have a ticket opened now and tier 2 support said they passed it on up the line. This was opened on Monday they said to give it 48hrs when I checked today support said to give it Till Friday. ticket# 4515000

Connected, yet not connected?

Similar Messages

Maybe you are looking for