Connecting 6720 Classic via USB crash PC USB devic...

When connecting 6720 Classic via USB cable to my Acer laptop all USB ports on laptop seize to work and Windows display a message that the USB device has malfunctioned. Eventually the PC is permanently stucked and only way to proceed is reset laptop on power button and prior to that remove the laptop charger to entirely power it off and let it reboot on battery. Harddisk controller is permanently indicating with a green light but harddisk is not spinning. When this happens the Nokia phone does not prompt for USB usage (connection type) and is also hanging in application execution for a while. I would like to be able to configure the phone not to charge via USB, but have not found a way to do that. I believe that the charging via USB is creating a low level hw driver and power surge problem in my laptop. Problem is not consistent but happens from time to time. When connecting the normal 230 VAC charger to Nokia device so the Nokia device is charging when connecting to laptop via USB the problem does not occur. In this situation the Nokia device will not try to charge from USB connection.
Any possibility to disable the charging over USB on the Nokia 6720 Classic device??

I had the same problem with my 6720 when I connected it to my HP laptop via USB to download maps. It crashed my computer making all USB ports unusable until I restarted the computer again. I think it happened after I downloaded the necessary software upgrade. I had to eventually use bluetooth to transfer maps data to my phone. It worked without any hitches. Can someone at Nokia fix this problem with the USB?

Similar Messages

AT300se...can I connect to TV via the micro USB port?

Hi, I was wondering if I can connect to my TV using the micro USB port on the AT300SE model tablet. This version does not ahve the micro HMDi port so i was wondering if I could use an adapter to conenct to my TV via the micro USB? Thanks, Nikos
Solved!
Go to Solution.

Looking at the specs, this tablet does not have HDMI. So I see no way you can connect it to your TV. Some of the newer TV's may be able so share your network to play files that are on your tablet.

Connecting my 6630 via USB

O/S - Win XP SP 2
Phone - 6630
PC Suite - 6.81.13
Hi
I'm trying to connect my 6630 via USB, i've installed and re installed PC suite but even though Windows recognises my phone, and installs the drivers etc. the Get Connected dialog on PC Suite shows as connecting but there is no response. What might be the problem and what should I do?
YK

What is the response you are waiting for ? What areyou trying to do with the PC Suite and how ?

Connecting MIDI controller via USB

Does anyone know how to connect a Roland SH-201 to a MacBook Pro via USB to use as a midi controller in Logic Express 8. I've installed the SH-201 driver, however I am getting a warning saying it is not compatible with an Intel based Macbook.
Just some general guidance in connecting a keyboard via USB to work within Logic Express 8 would be good.
Thanks.

Well, if the synth's USB driver is not compatible with your laptop's system, there is nothing you can do about it I'm afraid. There is always an option to get a portable USB to MIDI Interface (price would be around $20-50, I think) and connect your synth to Macbook Pro through it.

Apple tv showing wire to connect to itunes via mini usb cable which i dont have?

apple tv showing wire to connect to itunes via mini usb cable which i dont have?

You need to get the cable to restore the ATV to factory settings, following the procedure here.
USB mini cables are available from many different sources; often even from local stores like CVS or Walgreens. They are inexpensive, as little as a few dollars online & around $5 from some local discount stores.

While restoring iphone 4 8gb it is stuck at the connect to itunes via usb screen

While restoring iphone 4 8gb it is stuck at the connect to itunes via usb screen

Hi tanuj178,
If you had an issue while restoring your iPhone and are now seeing an icon instructing you to connect to iTunes, you may find the following article helpful:
Apple Support: If you can't update or restore your iOS device
http://support.apple.com/kb/ht1808
Regards,
- Brenden

Is it possible to connect two Macs via USB ?

Is it possible to connect two Macs via USB just like Firewire back in the day via Target mode or is there something similar? I am asking this because about 2-3 years ago I would normally image Macs via Target Mode. I used to have a regular Macbook running 10.6 along with a customized-ready-to-go .dmg image saved on the Desktop. Whenever I needed to put that image into any Mac I would simply connect the two Macs via Firewire, I would then press "T" at startup which will get me in Target Mode, I would then see the disk appear in the desktop of the Mac I had the image. I would then copy that image to the T mode macbook using super duper. Can this still be done through USB with new models and if so will I also need to press T at startup ?

No, USB connection does not qualify for this, only firewire and thunderbolt, as I read (but cannot test, for the time being I have only one such mac around).
This is why the short series of alu MBs (2008) are not qualified for target mode either.
p.s. What ‘new models’ do you refer to?

HT1386 During iTunes update on my pc, my iPhone was connected to pc via usb & was syncing, suddenly my iPhone stopped connecting to wifi and cannot activate. I cannot access iPhone data as it says connect to iTunes to activate but cannot connect

During iTunes update on my pc, my iPhone was connected to pc via usb & was syncing, suddenly my iPhone stopped connecting to wifi and cannot activate. I cannot access iPhone data as it says connect to iTunes to activate but cannot connect. How do i connect to iTunes to activate iPhone as iPhone cannot connect to WiFi or any other network
Please how do i reactivate iPhone?

Hello DadiPrince,
The following article contains information beneficial to getting your iPhone back into normal working order.
iPhone: Troubleshooting activation issues
http://support.apple.com/kb/TS3424
Resolution
Perform the following steps if you receive one of the messages above:
Restart the iPhone.
Try another means of reaching the activation server and attempt to activate.
Try connecting to Wi-Fi if you're unable to activate using a cellular data connection.
Try connecting to iTunes if you're unable to activate using Wi-Fi.
Restore the iPhone.
If you receive an alert message when you attempt to activate your iPhone, try to place the iPhone in recovery mode and perform a restore. If you're still unable to complete the setup assistant due to an activation error, contact Applefor assistance.
All the best,
Allen

Can I connect a drive via eSata/USB to one connected to MBP via FW800?

I have a drive that only has USB/eSata (Drive 1). I have another drive (Drive 2) that's got USB, eSata, and FW800... it's currently connected to my MBP via FW800.
Is the following possible?
Drive1===>USB/eSATA===>Drive2===>FW800===>MBP
The purpose of Drive1 is only to back up the contents of Drive2, I do not need to transfer anything directly from the MBP to Drive1.
Questions:
1) Is this possible without errors?
2) If so, what performance can I expect?
3) Which is safer/better, using USB or using eSata?

No. Although drive enclosures may have pass-through ports they are for daisy-chaining via the same port. Also, you cannot connect the drive by more than one port at a time without causing a potential dangerous condition for the drive. However, you can connect separate drives by separate ports. That is you can have one drive connected by FW, another via USB, and still a third by eSATA (if you have the requisite ExpressCard/34 card.)
Which is better? From fastest to slowest; eSATA, FW800, FW400, USB 2.0, USB 1.1.
The ideal method for accomplishing you stated goal is to get a two drive enclosure populated with two identical drives. Use Disk Utility to create a mirrored RAID array. What ever is saved to the array volume is mirrored on both drives automatically. The array should not be used as a startup volume, but it can be used to backup a startup volume.

What is the difference between connecting a printer via USB or Ethernet ?

What is the difference between connecting a printer via USB or Ethernet ?

When a Printer with an Ethernet connector is connected via Ethernet, it becomes a peer device on your Network. It is available whenever it is on for all users on your Network.
When connected via USB, it relies on your computer to "Share" it onto the local Network. It is only available when the attached computer is on. It takes resources from that computer to facilitate printing for any User.

HT201210 on my iPad I get an image of the USB connection and an arrow pointing to the itunes icon for a few seconds then it switches off. connected to itunes via USB get a message that itunes has detected an ipad in recovery mode must restore when i do

When I havent got my ipad connected to a power supply I get an image on my ipad of the usb cable with an arrow pointing to a itunes icon and no matter what you try and do iyt stays on that for a few seconds and then switches off the ipad, connecting it through usb into itunes on my PC (XP) this image says on the screen but I get a message on itunes saying itunes has detected an ipad in recovery mode and mneeds to be restored - when I fire off the restore through itunes after a few minutes it comes back and says it cannot restore and give an error message 1603. I have also repeated the process through my wife's laptop (Vista) and get the same situation -it is an 32GB Ipad 3 purchased last November - any ideas ?

Try and turn off iPad/iPod and proceed to step 3 of Recovery Mode.
Recovery Mode
1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
Note: Data will be lost. You may have to repeat the above many times.

Nokia PC Suite - Connecting on PC via USB

Sorry, I habe a problem with the Connecting from my Mobilphone Nokia 3110 over USB-Cabel.
There come`s a answer on Step 3/4 from the Sofware (PC-Suite) I must deaktiving my Securitybarricade.
Silly Question: What means that ? ...but it`s new for me!!!
On my old PC I haven`t this Problem...!! It was ok!

When you open Nokia PC Suite.. do you get 'Click here to connect a Phone' ? Connect the phone.. click on that tab and follow instructions .. See if your phone gets connected now ...
Attachments:
PC Suite.JPG ‏36 KB

Can't connect my 5800xm via usb

when i try to connect my phone the pc does not detect it what should i do ?
the cable is ok and also the phone .
does it take too much time to connect the 1st time .

yes, 1st time you connect your phone will install cabel drivers.
P.S. - PC suite or OVI suite needed to connect your phone via PC suite mode.
Glad to help

Nokia 3230 unable to connect to internet via USB c...

when i use CA-53 cable to connect to internet using nokia pc suite7.0.8.2 (one touch access) an error message pops up "unable to connect to the speified device make sure the modem is configured properly" but i can easily connect to internet via bluetooth other functions like file manager , contacts , messages and back up can be accessed by using the CA-53 cable

I called a vw dealership (in South Australia) today because I have an iphone5 and a Tiguan and experienced the same thing (after i had purchased the lightening/30pin adapter).
I was advised that the media interface software is not compatible with iphone5. VW will eventually update the software according to ol'mate at the dealership, but it will be at an expense to the consumer allegedly.
I know that there is a iphone/vw media cable one can purchase from VW however, I believe this to only work with iphone4 or older?
Maybe try an older generation ipod to use for the car if all ur music is in itunes?
if anyone can correct me, I'd be more than happy to know... going to try my older generation ipad and see if there is any truth to the tale.... eventually. Until then i'll stream via bluetooth :-)
Sheree

Application invoked from portable space (USB) Crashed on windows 8.1 OS

Hello ,
I have an application available on portable USB Drive (Memory present on external controller ), I can open this application on PC when USB is connected to PC.
USB will act like mass storage device ,and application code is kept inside mass storage device .
when this application is evoked using binary file , it will send request (req.txt) to another controller through HTTP server and controller will send response back response (RES.txt) (Textfile format)
when RES.txt file will come on Portable drive , IT WILL GET CORRUPT . and application will crash.
i did Recovery and log is as follow :
C:\Users\Bino>chkdsk F:/r
The type of the file system is FAT.
Volume Serial Number is 0123-4567
Windows is verifying files and folders...
The size of the \RSP.TXT entry is not valid.
File and folder verification is complete.KP[;MK
Convert lost chains to files (Y/N)? y
512 bytes in 1 recovered files.
Windows is verifying free space...
Free space verification is complete.
Windows has made corrections to the file system.
No further action is required.
1,415,680 bytes total disk space.
512 bytes in 1 hidden files.
5,632 bytes in 5 folders.
512,512 bytes in 70 files.
897,024 bytes available on disk.
512 bytes in each allocation unit.
2,765 total allocation units on disk.
1,752 allocation units available on disk.
This works fine with windows 7 and 8 OS.
please guide me about the problem.

Thank you for the Replay,
I performed steps provided by you , but it did not help.
on other hand, i have collected some more data regarding
this issue.
1. went to SAFE Mode and tried to run the application from USB
2. got Exception "The instruction at 0x00407038 referenced memory at 0x00000078. The memory could not be read"
some more info on setup :
we have a micro controller on board, some part of memory (present on board) is used to keep application and server. we can open this memory via USB connection to PC. then we can see all files present at this memory on PC (behaves like externally connected
USB Drive) .
When we start this application . it will start the server . server will send 'request file' to controller soft. (this part is working fine), and controller will send back response , as soon as response file(RSP.txt) will appear in USB drive it will get corrupted
.(here RSP.txt file is present in controller USB decided memory but to open this we are using PC RAM). crashing of RSP.txt file will crash whole application. This RSP File is of FAT Type.
i have copied application in another external drive and tried to RUN application. it will not crash . but USB can not receive the "RSP.txt" (as it is not in communication with controller soft). and problem is in response file.
BR,
sanjyot

Connecting 6720 Classic via USB crash PC USB devic...

Similar Messages

Maybe you are looking for