Connecting a laptop PC to a wireless router on an iMac

I cannot get a laptop PC to connect to the internet through a Linksys wireless router I have connected to my iMac. It was working great for a while, but the network disappeared from the laptop's "available networks" box, and I've been trying for hours to get it to work again. The Mac help desk was of no help and said I had to call Linksys, however, I think it is how I have the network or sharing configured. I've changed so many thinks trying to get it to work, I have probably messed all the configurations up.
This can't be that hard. Can anyone help? Thanks in advance

Since you already have the iMac connected, via Ethernet, to the Linksys router, you'll want to disconnect the modem's USB connection to the iMac.
Which model Linksys to you have? If it has more than one Ethernet port, try connecting the PC to one of the Linksys's Ethernet ports and verify that you can get an Internet connection.

Similar Messages

How do I connect my laptop to my Linksys wireless router through the internal wireless card?

I just purchased a gateway laptop and was trying to hook my Linksys wireless router up to it. Ive gotten it hooked up but only through the secondary device (that catches the signal)... I was wondering if there is anyway that I could make my internal wireless internet card a point or no? Can I only connect it to the USB network adapter or is there really a way to go COMPLETELY wireless? Thank you for your time...

Is your internal wireless card enabled? Go to device manager and make sure it is enabled.
Chuck

Hp6700 Printer: can't connect to D-Link DI-514 Wireless Router when Broadcast SSID is set to NO.

HP6700 Printer: can't connect to D-Link DI-514 Wireless Router when Router Broadcast SSID is set to NO. My MAC LapTop and HP LapTop both work with the SSID set to NO. If I change the Wireless Router to Broadcast SSID is YES, then the HP6700 Printer can connect to the Wireless Router. I setup the Printer telling it what the SSID and Password were, the same as both of my LapTops, but it never connects, unless I change the Router to broadcast the SSID. Help!
This question was solved.
View Solution.

Did you try updating the firmware on the DI-514?
You can also try setting a static IP on the printer, then assign the printer to the static DHCP list in the router interface.
To give your printer a static IP address:
- Print a Network Config Page from the front of the printer. Note the printer's IP address.
- Type that IP address into a browser to reveal the printer's internal settings.
- Choose the Networking tab, then Wireless along the left side, then the IPv4 tab.
- On this screen you want to set a Manual IP. You need to set an IP address outside the range that the router automatically sets (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') to 250
- Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
- Enter your router's IP (on the Network Config Page) for the gateway.
- Enter 8.8.8.8 for the first DNS and 8.8.4.4 for the second DNS. This is Google DNS. You can choose another external DNS if you wish.
- Click 'Apply'.
Now, shut down the router and printer, start the router, wait, then start the printer.
After this you will have delete and re-add the printer on your Mac.
Show support by clicking the blue Kudos star in the post that resolved your problem. Doing so will help other forum members find their solutions too.

What are the settings for connecting to a Mac behind a wireless router?

I have a client with an iMac. His Mac connects to the internet through a wireless router which gets its signal from a cable modem. My Mac is running 10.6. The remote iMac is running 10.5.
How do I configure my Mac (Administrator) and the remote iMac so a connection can be made using Remote Desktop.
Thanks!

In the AirPort Utility, I selected the Advanced tab, and then selected Port Mapping.
Q: What service do I choose from the drop-down menu? Also, where do I enter the two ports you mentioned? Public UDP Port(s)? Public TCP Port(s)? Private IP Address: Private UDPPort Private TCP Port?
still confused, I guess. Thanks!

Need help setting up my d-link wireless router to my imac

I need some help trying to set up my D-Link WBR 2310 wireless router to my iMac. I currently have Bell Sympatico high speed.
The reason I want to set up the wireless router is because my girlfriend works from home sometimes with her office computer downstairs and needs a wireless connection (she has a PC). I tried to call D-Link, but they're useless.
Anyways, any help would be greatly appreciated. It would be great to know what settings to change and as much step by step info as possible. I realize it's probably pretty simple to set up, but I'm fairly new to Macs and also to wireless.
Thanks again

Hello,
Connect the D-Link to the iMac by Ethernet.
Open Safari (or Firefox)
Navigate to http://192.168.1.1
Enter your password (default user is Admin and password "admin" - change it!)
Find the Wireless Security section and change the SSID to your own name i.e. "home network" .
Set the Encryption setting to "WPA" and enter a password of your choice. This is the encryption key and is different to the router's admin password.
Configure the WAN part of the router (which will vary depending on your ISP).
Configure the DHCP to serve clients (should be a simple on/off).
Disconnect the iMac
Go to the iMac and turn on Airport on (on the menu bar).
When the iMac finds your SSID select it and enter the encryption password.
Check to allow Keychain to store that detail.
Hope that helps
mrtotes

What is the best wireless router for my imac G4

i need a wireless router for my imac g4. Which one do you recommend? All all wireless routers capatible with macs?

As Donald mentions, the routers are all compatible with Macs, but the software CD that they include often has Windows specific software on them that is really just a front-end for configuring the router for use. It does nothing that you cannot do yourself manually by accessing the router through the IP address that gets you into the router settings.
If it sounds difficult, it certainly is not. Once you are in - and that is simple - the router's info is in a nice graphical interface that is simple to use.
I use a Netgear WGR614 for my mixed Mac-PC network at it works like a charm. I got it at Best Buy for $39.99.

I need help connecting to my wifi thru my wireless router at my house

i recently bought a wireless router for my house. i got it working fine. then my husband connected his laptop to the router and now my ipad will not connect to wifi.

You should probalby contact the maker of the router for suppot.

Laptop is not detecting wireless router

Thanks in advance for any assistance.
Equipment:
Gateway 450ROG
Intel PRO Wireless LAN 2100 3B
Linksys BEFW11S4 Wireless Router
SSID is enabled
Channel 1
I bought the laptop used and I upgraded it to WinXP SP2 and now it is not detecting any wireless nteworks. There doesn't appear to be an exteranl switch for the radio on the laptop. All drivers have been upgraded to their latest version. I was able to do this via a wired connection.
Help. Thanks.
Darrell-

Right Click on Intel Utility on the Tool-bar Try .... click use windows to configure the wireless settings ....
Go to start >> run >> type "services.msc" (without quotes) >> Under that list ... look for Wireless Zero Configuration >> Go to properties >> Use Start up type as Automatic .>> Click Apply & OK ....
Go to wireless network connections .... under view available wireless networks .... see if you are able to get your home network or not ...
Try to connect to it ....

Connecting an older computer to my wireless router.

My wireless router is connected to my work computer which is in the same room as my own personal computer. I can hard wire the two together since they are only a few feet apart, but my older computer only has a phone line connection. Are there cables with a ethernet plug on one end and a phone line size plug on the other, or what do I have to do to hard wire these together. My older computer, which still works just fine for my personal needs does not have wireless capability so I was hoping somehow I could hard wire this to the router. Any help is much appreciated.
Message Edited by bzmom23 on 09-14-2008 09:32 PM
Message Edited by bzmom23 on 09-15-2008 05:31 AM

Also, does the older computer support USB? (Don't laugh; there's a method to the suggestion!) Even if, for some reason, there's no room to mount a wired or wireless network adapter inside the computer, there's nothing stopping you from using a USB network adapter (wired or wireless) to connect to the same computer. Since there are USB wireless network adapters available (wireless-b, wireless-G, and wireless-N, as well as multi-protocol), do give serious consideration to having one or more around (if for no other reason than as spares); I'm looking to pick up one or two such USB adapters for my two-computer all-wired network (the router is a WRT54GS V.2, but may shortly be replaced with a WRT-310N for additional range and wired gigabit support). I've had my GS since 2005, and I'm very happy with it.

How do i connect my iphone to my wndr3400 wireless router

I dont know how to connect my iphone to my wndr3400 Netgear wireless router. do i have to add the phone to my homegroup?
Thanks

You don't - you sync them via iTunes on your computer, they cannot be directly connected together

Win 2000 PC can't connect to a WEP enabled BEFW11S4 wireless router

Hi,
I just set up my wireless router to use WEP with 124 bits encryption. However, when I installed the WUSB11 wireless adaptor on a windows 2000 PC, it couldn't connect to the router and get an IP address. If I do an "ipconfig", it shows the "Cable Disconnected" state and no ip address.
Could any one help?
thanks very much.

Thanks for your advice.
However, I'm not sure where to enter the WEP key on a win2K PC. It doesn't ask for the key during the installation. In "Infrastructure mode", only SSID is required. In "Ad hoc mode", SSID and channel ID are required. But neither asks for the key.
When installed in "infrastructure mode", it shows as "cable not connected". But if installed in "Ad hoc mode", the network connection is enabled and it tries to get an ip address, however, it fails to get a valid IP address from the wireless router (192.168 range) and returns with a 169.254 address.
Seems that I missed a step somewhere to put the WEP key?
many thanks.

DSL Connection Very slow ONLY when using wireless router

My DSL connection was running super slow (approx 136 Kbs) - I disconnected the Linksys wireless router and plugged by DSL modem directly into the computer. Then my internet speed increased to 1.4 Mbs (a 10 fold increase).
Any suggestions on how / why my speed drops so extensively when using the Linksys wireless routher (wrt45g).
Thanks

Are you using the same test each time to measure the speed?
The reason I ask is that Windows usually reports its download speed in KB/sec (Kilobytes per second). But most web (internet) speed tests report their speed in Mbps (Megabits per second.)
A 1.4 Mbps line will typically pass data at about 140KB/sec.
To help determine what kind of problem you are having, do the same speed test in 3 different ways:
1) Connect one computer, by wire, directly to your modem
2) Connect one computer, by wire, directly to your router (all other computers and network devices should be off).
3) Connect one computer, wirelessly, to your router (all other computers and network devices should be off).
Report back your results, and also, please state what line speed you are paying for. Once we have this, we will hopefully be able to help you.

I am trying to connect my Photosmart Printer to my wireless router

I need to get directions on how to connect NETGEAR wireless router to HP Photosmart printer.

Hi,
What is your printer ? And what is the Operating system of your computer ?
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Connecting Westell 6100G to Netgear n300 Wireless Router

I've just purchased a netgear n300 wireless router. My question is would I defintely need to set the Westell 6100G modem to bridge mode? After I do that I simply connect the wireless router to the modem and then the router to the computer via one of the ports? After that is done would I need to do anything else? Would I be asked for my verizon login and password in order to get connected?
Solved!
Go to Solution.

It's recommended to bridge your modem as the modem itself does have an integrated router, even though it only has one Network port to connect up with. You have to split it up using a switch if you wish to really use it as a wired router. The reason why you bridge is so that your router holds your Public IP address rather than the modem. This avoids a condition known as "Double NAT" which game consoles dislike, VPNs tend to be iffy with, and Port Forwarding becomes a pain to do as you have to do it twice.
Yes, Bridge the modem. As far as the Netgear is concerned, if your modem reports that it is using PPPoE, the Username and Password you will need to use will be the master login you use for your DSL account. In the Netgear, it will auto detect that you use PPPoE in most circumstances however, it won't automatically pull your username and password. In some cases it may just connect right up if Verizon still does OpenPPPoE. Otherwise, if you're using a Setup program that came with the router it should ask you for your username or password to connect up. If not, Netgear has changed their firmware around in recent years, but in most cases it is under the Basic Setup or "Internet" section of your router for adding in a PPPoE username and password. The best place to look for this would be the user guide for your router. It should detail how to set up your connection based on what you're using.
========
The first to bring me 1Gbps Fiber for $30/m wins!

Ipad connects with Airport Express, but not wireless router

I have a airport express that exends my network and is connected by an ethernet cable to the wireless router. they are on opposite sides of the house from each other. every other device i own has full bars wifi anywhere in the house. but the ipad only seems to find the signal from the AE.
If i go in the bedroom with the wireless router, the signal drops to 1 bar. if i unplug the AE along with all the other electronics for the TV/Receiver at night, the ipad loses the signal and cannot get a signal from the router, standing right next to it. i have tried reset, hard reset, renew lease forgetting network, and all fails. any ideas?
I have a Verizon Ultraline series 3 model A90-9100EM15-10 and the firmware is up to date.

Disclaimer - For me the Apple Support Communities are an international user to user technical support forum. As a man from Mexico my first language is Spanish. I do not speak English, however I do write in English with the aid of the Mac OS X spelling and grammar checks. I also live in a culture very different from that found in most 1st world nations, such as that in the two dominant North American countries. Written language has no tone. When offering advice in the ASC, my comments are not meant to be anything more than helpful and certainly not to be taken as insults.
You likely have your reason for extending your network in this manner, but it seems that the AE is not really extending your router's network, but creating its own separate network that then extends your internet connection. This can be confusing to devices if you are expecting that they will switch between the two of them automatically.
The iPad can only support one connect at a time. It sounds like you want it to be able to jump from the AE connection to a router connection on a whim when signal strength drops. I am not sure that the iPad's radio is that sophisticated. At best when the iPad looses a signal it could ask if you want to join any other network that it detects, especially if it has connected to that network in the past.
AFA the router, some routers don't like iOS devices and just won't connect. When you go to Settings/Wi-Fi does the iPad see the router's network? If the iPad sees the router network, try configuring a connection by hand.
Tap Other... and write the name of the router's network. Tap Security and select the type of security the router's network employs. Return to the previous pane and enter the password. Tap Join. If you can make the conection the iPad should remember this network in the future. Turn on Ask to Join Networks and hopefully when the iPad looses the AE signal in the future it will then ask you if you want to join the router's network.

Connecting a laptop PC to a wireless router on an iMac

Similar Messages

Maybe you are looking for