Connecting a wireless printer

Can I connect my desktop computer to a J6480 with a USB cable and have my laptop connect to it wirelesly. the install directions are confusing
thanks

Yes you can. Install the printer SW on your desktop following the USB connection instruction and then install the printer SW on your laptop using the wireless connection instructions. The order doesn't matter.
Regards / Jim B / Wireless Enthusiasts
( While I'm an embedded wireless systems engineer at work, on this forum I do not represent my former employer, Hewlett-Packard, or my current employer, Microsoft )
+ Click the White Kudos star on the left as a way to say "thank you" for helpful posts.

Similar Messages

Can not connect my wireless printer to the new router.

Can not connect my wireless printer to the new router.

Can you please provide details:
1. The make and model of printer
2. Make and Model of Wireless Router
3. Is your printer connection wireless to router or a cable to PC
4. What have you done or attempted to do to establish a connection?
5. Any further info to assist

How do I connect a wireless printer with my ipad 5.1?

How do I connect a wireless printer to my iPad?

If its listed as 'airprint enabled', then you can follow the steps in this article:
http://support.apple.com/kb/HT4356

I need to connect my wireless printer (HP LaserJet CP1025nw color) to the internet.

I need to connect my wireless printer (HP LaserJet CP1025nw color) to the internet. I recently have changed my name and password of my modem. Since the change I have lost connectivity between my computer and my printer. What do I need to do to regain connectivity? I am using Windows 7.
Trydell

I think you mean your password on your router right? Changed your SSID and/or password?
Try here.
http://www.hp.com/global/au/en/wireless/reconfiguring-system-help3.html
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

Can't connect to wireless printer

I cannot connect a wireless printer...I have tried 2 printers. HP photosmart 6510 and Epson SX535WD....the wireless strength appears to be good on the printer but the MAC can't see it and neither can the iPhone or the iPad....Sooooo frustrating. Have brought back printers to shop as thought they were faulty...They immediately signed in to their own wifi and printed no prob from iPhone....spoke to my broadband provider. They suggested might be interference from cordless phone, so switched that off....no success, then they said something about changing the WPA to WEP....this is becoming way too complicated for something that I thought was going to be plug in and go....Should I just give up and buy an old fashioned USB type....will I ever be able to print from the iPhone or iPad as well....HELP!!

My mother has been using an iPad. She wanted a printer. The media would think you just buy an AirPrint printer and you're good to go. I bought an HP PhotoSmart 6510. It connects to the wireless signal at my mother's home, but the iPad doesn't recognize that an AirPrint printer is available. Cisco (router) recommended disabling SSID, more or less. I disabled the "SSID broadcast" under guest access (I think I went further with the tech attempts than most other people) using the Cisco software (and rebooted the router, I think), but still no go. The iPad still doesn't recognize the presence of an AirPrint printer. Very frustrating. IF the iPad had a USB port we could go back to the era of cables and print that way, but that's obviously not a solution. Feel mislead. Under the current circumstances most people are going to be frustrated and mislead by the media hype that says, "You can print wirelessly from you iPad, especially if you get an AirPrint computer." Things are going to have to get much simpler for widespread acceptance of that notion. Most of us don't have hours to spend trying to sort out tech issues on our computers. Frustrating!

HT4972 Hi I have an iPad with iOS 612 and am trying to connect a wireless printer, I don't think it's doing it because I don't have iOS 10 or more. Is this right?.

Hi I have an iPad with iOS 612 and am trying to connect a wireless printer, I don't think it's doing it because I don't have iOS 10 or more. Is this right?.

If you want to use AirPrint - the buit in feature in iOS that allows you to print directly from the iPad without another app - you need to be using an AirPrint Printer. There is a list of those printers here.
AirPrint basics
If your printer is not on the list, you may still be able to use your current printer, but will need to purchase a printing app for the iPad from the App Store.
I don't understand you reference to iOS 10 unless you mean OS X10 for Mac.

How do i connect my wireless printer

i haveing issues seting up my wireless printer to my mac pro

I have a HP Photosmart printer. Everything is hooked up correctly. How do I connect my wireless printer to my computer???

Can't connect to wireless printer D110 Photosmart

I've tried several times now to connect to this printer wirelessly - I'm in college and it is my roommate's printer, and she apparently didn't got through the whole process of inserting the cd and going through installation and so on, but is effectively hooked up wirelessly to the printer. Every time I have gotten the same message.
"The IP address (my IP) of the PC and IP address 192.168.181.93 of the printer are not compatible. Turn off the power to the router and the printer. Wait 60 seconds. Turn on the power to the router and then the power to the printer. If the printer and PC IP address are still incompatible, reboot the PC."
I can't turn off the power to the router because it's the residence hall router - dont even know where they are. But I have been through this several time now and just have no idea at all how to resolve it. Ideas?

You need to be connected to the same network as the printer. Does she have a wireless router in the room that the printer is connected to? If not, even though it appears you are on one University network, it is likely many networks, all with the same name. Each of these networks will have a different subnet (like the 192.168.181.X on the printer). Look at your PC and find its IP address. The first three sets of numbers will have to match the printer's.
Need help? Let me know what operating system you are using.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Can I connect a wireless printer to two wireless networks

I searched and couldn't find an answer to this exact situation. The answers to similar questions didn't seem to work.
Can we share a wireless printer over two wireless networks without adding hardware or changing the wiring or doing complicated software modifications?
Here is my set-up:
Cable Modem> Linksys Wireless Router “N” on the first floor > older AirPort Extreme “G” via ethernet cable on second floor > Laser Printer via USB Cable on the second floor, plus an AirPort Express to extend the area on the second floor. We have 2 MacBooks and 1 MacBookPro that connect to the internet via either of 2 wireless networks. Generally, for better connection, you choose “N” if you are on the first floor and “G” for the second floor.
Currently, if you want to print to the USB Printer, you just select it in the print dialog box. It does not matter if you are on Network “N” or Network “G.”
We just added a new wireless Printer that’s on the first floor. (No, I didn't read the directions, the printer screen said if there is a W?? button on your router, press it. I did and it automatically connected to the “N” network. It also has its own email address for printing without a computer, but that still doesn't solve this question.)
If you want to print to this printer, you must first change the computer’s AirPort setting to join the “N” network. If you don't, you still get the print dialog box, but eventually you will notice that nothing happens. The document just sits in the Printer’s queue.
Is there a way to get a computer on the “G” network to find the wireless printer on the “N” network without first changing networks?
Remember, it automatically finds the USB printer that is plugged into the “G” network router.

It used to be that if you wanted to wirelessly extend the range of a network, you'd have to set up a WDS. (WDS = Wireless Distribution System.) There was no "Extend a wireless network" option and no "Allow this network to be extended" checkbox—you'd have to fill out lots of WDS information yourself. It was sort of a pain.
Then, with the 802.11n AirPorts, Apple introduced the "Extend a wireless network" option, greatly simplifying the setup process. It accomplishes the same thing as a WDS, but it's easier to set up and has less overhead. However, it can only be used if every AirPort in the wireless network supports 802.11n.
Your Express may support 802.11n, but your Extreme is older and does not. So "Extend a wireless network" won't work for your network. That's why you got errors when you set the Express's "Wireless Mode" option to "Extend a wireless network." Instead, you'll have to do things the old-fashioned way* and configure the Extreme and the Express to be part of a WDS. Your network will still work as desired: the Express will rebroadcast the signal from the Extreme, and clients will connect to whichever station has the stronger signal. It's just that you'll be using the older WDS technology instead of the newer "Extend a wireless network" feature.
"Join a wireless network" is something different entirely. You'd use it if you wanted to connect to a network but not rebroadcast it. This could be useful when, for instance, your main router isn't an AirPort but you want to use AirTunes. In your case, however, this option wouldn't be very useful.
Look at [this thread|http://discussions.apple.com/thread.jspa?threadID=2588489] for more information.
*Actually, the old-fashioned way would be to use modems. Or to forget about the internet and send snail mail instead.

Using the Embedded Web Server To Connect A Wireless Printer To Your Network

AKA:No Wireless Setup Wizard Button, which would be way easier.
The Prelude
Some entry level printers do not offer a 'Wireless Setup Wizard' button, or a menu option that is accessible from the front of the printer. Printers that do not offer this luxury option, can still be easily configured to communicate to your router if you have a Mac or Windows PC.
You still may have an easy option to get your network settings configured in your printer, if your router supports WPS. I personally do not like to use WPS as it can bring its own frustrations. WPS is not within the scope of this document.
This document is geared towards the last available option, and in my opinion the best option. It can however be the most involved option. I am referring to using the Embedded Web Server (EWS). Most modern network capable HP Printers have a setting page that can be accessed from a web browser. The process is rather simple, but many confusing hiccups can occur, and that is what I hope to prepare you for. There will be variances for different printers. I am using my experience with consumer printers that have been around the last few years.
First, do not get overexcited about this document: Accessing the HP Embedded Web Server. Don't get me wrong, it is a great document, it's just that the instructions, while accurate, will not work until your printer is configured to connect to your network first. We will revisit this later however.
Seatbelts Please
The first thing we need to do, is have the printer broadcast its own network, sometimes referred to as AdHoc, sometimes referred to as Auto Wireless Connect. To do this, you need to navigate the menu system of the printer, and find the option to reset the network settings, network defaults or something similar. If your printer has the Wireless Direct feature you won't need to reset the network settings, but this is a perfect time to make sure Wireless Direct is turned on. If you aren't using Wireless Direct, the timer starts. Generally speaking, for the next two hours, the printer will broadcast an 'HP Setup' network, or have some variation of the printers name listed in available wireless networks. Regardless you should have plenty of time, if you read it all first and then went throught the steps.
*Preparation:
Here is where you want to use your favorite device, one capable of seeing 2.4ghz networks. Android phone, Apple iPad, Chromebook, Windows or Mac Notebook that you decided not to install the printer software on. Any of these devices will work. Apple iOS devices required a bit of coddling, as Safari doesn't work well with the EWS Wireless Setup Wizard.
Do you know your network SSID? What about the passphrase, passkey or whatever the security word is called?
If you didn't set it up, and just started using it when the internet guy installed it, then there is probably a sticker on the router with that information. If you still can't find it, call your ISP, router manufacturer or favorite family member for help to find that information (If you use a family member, remember to buy them something nice on the next gift giving holiday in your region).
*Apple iOS specific, device preparation:
1. You will save yourself a lot of frustration by downloading the Chrome Browser for iOS now. Go ahead, I will wait...
If you are installing Chrome for the first time, when it completes the install, open it, and get passed the greeting and tutorial before continuing.
2. You need to forget your home network connection when you are done with step 1. Just hold down on your home network in the wireless networks list, and 'Forget' the connection (or find the arrow that leads to the same option). If you do not take this step, it will reconnect to the home network once you run the Wireless Setup Wizard, causing you to have to back track.
3. Be aware, when you connect to your printer's network, that it may appear to not connect (ie. spinning wheel, no confirmation) to the printer. This is a known behavior. Just close the wireless settings, and proceed as normal.
Begin The Journey
Open up the wireless section of your device and look in the list of available networks and tell it to connect to the HP printer network. The SSID will usually start with HP, and may have the printer model or the word SETUP in the name. Once you are connected (see "Apple iOS specific, device preparation #3 if you are using iOS), it is time to open your browser, preferably the Chrome browser when at all possible. In the address bar type 192.168.223.1 and press go or hit enter. I use the colloquialism 'hit' when I just mean 'press' again, sorry for the redudancy.
If all is well, you should see a web page that should refer to your printer. Now is the time to find the 'Wireless Setup Wizard' button. Most printers should have it here on the main page of the EWS. Just take your time, it may not be obvious at first. Once you press it, the setup process will begin. Follow the instructions. It should see a list of detected wireless networks, and you can select your home network. Then if it requires a password, it will prompt for you to enter it. At the end of the Wizard, it might say something about not being able to test it, or show a page cannot be displayed screen. This is OK. This means the printer is now talking to your router and not your device in your hand.
Proof Of Concept
You can now tell your device to scan and connect back to your normal home network. Once you connect, you can verify if you can see your printer. Keep in mind, with dual band routers, that the printers will typically only be visible on the 2.4GHZ network, so your device should also connect to that network as well for testing. Once connected, now we need to find out what IP Address the printer has. Remember the document I started with “Accessing the HP Embedded Web Server”. It now is relevant, and you can complete those instructions to make sure you can see your printer on the same network. If your device can enter the printers EWS with its new IP, then you have officially connected your printer to your network. Also your printers wireless light should be solid, indicating communication.
If It Worked
Now the fun begins. If you are setting up ePrint, and if there is no option to configure ePrint from the front panel, find the Web Services tab, and proceed with that process. If you are setting it up to a Chomebook, you still need to setup ePrint (if it is an ePrinter) before configuring Cloudprint... but that's another document.
I hope I have not missed any small detail that pertains to your configuration that made this hard to follow. Any comments would be welcomed to improve this for future use.
TwoPointOh
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

That printer also has a USB port why don't you connect it using that port?
If you insist on using ethernet, Mac OS X can create two network connections at the same time. On the iMac you can configure one of the network connections to be wireless and the other to be wired using the ethernet port.
Since you already have a wireless network configured and connecting to your AirPort Extreme for Internet access all you need to do is plug in an ethernet cable from your iMac directly to your printer and configure them to use self-assigned IP addresses. Self-assigned IP addresses take the form of 169.xxx.xxx.xxx and are used in this configuration to avoid any conflicts with your other network. You have to configure the iMac and the printer to each have a unique IP address in the self-assigned range, just make each of the last group of numbers in the IP address different, and then the iMac should be able to print to the printer.
Note that when you configure the Imac and printer this way no other network devices will be able to print

Not all laptops in household connect to wireless printer on AEBS

I have the latest Airport Extreme Base Station (n), and an HP Deskjet 5900 printer connected to it's USB port. The AEBS is setup to Share the printer wirelessly. I've also made this option available through the main desktop (Mac Pro) that is connected directly to the AEBS.
I have a MacBook (intel) connected wirelessly to my network. I was able to connect to the "Add" the HP to my list of printers and successfully print to it wirelessly.
Unfortunately, our MacBookPro that is also connected wirelessly can not locate the printer.
Some facts:
-Both laptops are running 10.5.8
-Both have the latest HP Printer Drivers
-Both are running admin accounts, so we should be able to make any necessary changes to printers, prefs, etc.
Couple of things to note:
When hitting "Add" on the MacBook, I get an extensive list of connection options, e.g. "Default", "Fax", "IP", "Apple Talk", etc... the HP Deskjet is connected via Bonjour.
When hitting "Add" on the MacBookPro, all I get is one two column window with the option "Local Zone" at the left, nothing on the right hand side, and the fields "Name, Location, and Print Using" below... all of which are not selectable.
We are able to print to a hardwired USB printer connected to the MacBookPro, but that's about it.
The MacBookPro does have Parallels installed, so I don't know if that is some how changing the behavior of this panel, but we aren't running it at this time, since this is being setup in the Mac OS side.
Hopefully that is enough information to give a clearer picture. I'm hoping it's a setting somewhere that for whatever reason was inadvertently turned off.
Thanks!

A couple things to keep in mind with what you are trying to do: the AirPort card was originally intended to allow the computer or laptop to connect to a wireless base station, such as a router, AirPort Extreme, etc. It just so happens that setup properly they allow the computer to work as a wireless connection point to the internet for another device. They are not intended to provide the full functionality of a router, however.
While a number of people using the forums have discussed connecting devices like iPads to the internet via their iMacs and MacBook Pros, using the computer to provide internet access and at the same time work in reverse by providing wireless printing could end up causing signal clashes and conflicts.
You would be far better off installing a router to provide the functions you are describing. Or keep very tight controls on what device is doing what and not over burdening the AirPort card.

How do I restore connection to wireless printer?

Wireless printer is not recognizing macbook. How do I restore wireless printer connection?

Open System Preferencses > Print & Scan > Print
Delete the current printer in the list.
Restart your Mac and turn off the printer and turn it back on.
Now click + from the Print tab to set up the printer again.
OS X: Connecting a Wi-Fi printer to your Wi-Fi network

Unable to connect to wireless printer or download firmware update

Got an HP C4580 all-in-one wireless. Can see the device wirelessly using the HP Utility, but cannot print to it "Printer is not connected" or see it using System Preferences. Have downloaded the firmware update, but when running this it hangs at the device discovery stage (even when connected through USB) and therefore I cannot update the firmware on the printer.
The printer will print when connected throught USB.
Driving me nuts!
Jim

Thanks for the information. Network is not complex. Cable Broadband connected by ethernet to AirPort with an additional AirPort (Time Capsule) to extend the range of the network through the house.
I did all as you suggested, and this worked fine (once) for twoMacBook Pros, and two iMacs, and now won't work on any of these again (one day later).
Am reluctant to reset the printers again, as my print list includes five printers from work, which requires the IT Dept to reconfigure again if I clear them once more.
HP Utility can apparently connect to the printer and give me device information, I just cannot print to, or scan from the printer.
As advised before, I cannot install the firmware update (it may alreadybe installed - how would I know)? It just hangs when trying to seek the printer type.
The lack of wireless printing is driving me nuts. Before the problem arose with complete loss of service, I went through a period of a few weeks where the printer would not connect after it had printed a job, and had to be switched off, then back on again before working wirelessly. Now nothing.
Kind regards,
Jim

Connecting Samsung Wireless Printer w/MacBook

Im having great difficulty trying to set up wireless printing between my MacBook and a Samsung ML-2955DW wireless printer. I wanted to check in on these forums first, before calling Samsung, because, admittedly, I need help with the basics. And, I would like to gain a better understanding about what it is Im supposed to be doing before speaking with them.
The "Players" are as follows:
-MacBook 2GHZ Intel Core2 Duo... w/System 10.5.8
-(2006) PowerMac G5... w/System 10.4.11
-Samsung ML-2955DW Printer
-Airport Express Brick 802.11n
-Realtek WLAN Wireless Wifi USB Adapter
My first question is... is this even possible with the set-up that I have? My G5 does not have Airport built in. I had to buy the Wireless Wifi USB Adapter to plug into the back so that my MacBook could link with it.
I was going with the notion that it is possible and tried to set-up the printer according to what the Samsung instruction book calls an Infrastructure Mode Set Up; that is–connecting to the printer via a router. For this set-up they show a diagram where the supplied USB cable connnects directly into the back of the Desktop computer. The directions continue with how to change the IP address, Subnet Mask, etc... and then they end. So am I to assume that if I am able to complete the installation process to my Desktop computer I will then be able to install the driver on my MacBook and be able to print wirelessly? I have tried this method with no success at all.
The furthest I got with trying to get a connection was by following directions posted on MacRumors for another wireless Samsung model. They instructed connecting the printer directly to the computer with an ethernet cable (not sure if they meant to connect to the desktop or laptop, I connected it to my desktop, as it wouldnt work at all connecting it to the laptop). I was able to get the IP, Subnet, etc.. info from the printer by doing this and changing it to my network settings via their Sync thru Web method. However, in the end, I could not change the TCP/IP setting to DHCP or set up the wireless printing.
Thank you in advance for any help with this, I can surely use it.

This is for Snow Leopard, which you show you're using - might be of some help. I have a Canon MG8120 which I print to with ease (scan, too). During your setup, you should have had the printer 'seen' on the network.
Regards,
Clinton

Connect to wireless printer

I just bought a wireless printer (Samsung CLP-315W) and would like to connect it to ma MacBook air.
The instructions says that first of all U should create a adhoc network on my Mac:
System Preferences, network settings, open the network name list and choose"airportthrue".
But there is no "airportthuru"-possibility in the list. What do I do to create the adhoc network??
Thanks

the option your looking for is "create a network" the fastest way to do this is: menu bar, airport menu, "create network..."
or alternatively you could do: menu bar, apple menu, system preferences, networking, click on airport, under the pull down menu "network name" chose "create Network..."
Do you already have a wireless network you use to brows the internet? If so is there a reason your printer can't join that network?
I'm asking this because, you will not be able to join other wireless network while using "create network". witch means if you get your internet over wifi, you won't be able to brows the internet and print.

Connect to wireless printer for first time

I'm trying to connect to my Epson Artisan 810 printer with my brand new mac for the first time. I'm new to mac so please forgive my ignorance. With my windows xp laptop, I downloaded the driver from Epson, installed, it found my printer and I was off to the races.
For the mac, do I need to connect to the printer with a usb cable for the first time? I went to the epson site and it sounds like I click on the apple, select updates and something should happen, but nothing. I've tried to discover devices thinking that would trigger something, but all that it has found is the memory card on the epson printer.
Any help is very much appreciated.
Thanks,
toby

Sig,
Thanks, but this is an existing printer that is already set up to my network and works great printing wirelessly for iPads, google print, win7, etc. My issue was getting my mac book pro to print. I'm new, very new to macs and after following the instructions for setup, it still didn't work. I found this article on justanswer and it worked great.
Seems once I plugged into the printer, mac recognized the printer and did its update, I had to disconnect from the usb, shutdown the printer, reset print and fax in mac preferences, reboot the mac. Once mac came up, i restarted the printer, went back into print and fax and selected the "+" sign to add the printer back in. Once I did that, printing was working great. Seems like a lot of steps compared to what I did for xp laptop and win7 laptop, but I'm still liking the mac. I just wish some of this stuff was documented better on apple's site.
Again, thanks for the help. I'm sure I'll be asking more questions.
http://www.justanswer.com/mac-computers/4pceg-hi-macbook-air-epson-artisan-810-p rinter-says.html

Connecting a wireless printer

Similar Messages

Maybe you are looking for