Connecting a WRVS4400N to a Dell Swtich

Good Morning,
I want to buy a WRVS4400N, but I need to know something before.
The router will serve as an access point for 10 wireless station, 6 of them will run over Terminal server, the router will also serve 20 computer for the internet, so I want to Link aggregate the four LAN port to my swtich, I know how to do it on my Dell Powerconnect, but I want to know if the WRVS4400N will support it, there will be a lot of traffic going through the router so linking the 4 port in LAG mode to my Powerconnect swicth will speed up the communication !
Thank you,
P,S: Sorry for the multi post, I was lost in the cisco support site !
Sylvain

Sylvain,
I wouldn't go with the WRVS4400N in the scenario you specified. the router doesn't do LAGS (any router in SBSC product line doesn't support LAGS) next if you're using an internal DHCP server , DHCP request will get sent to all Vlans on the 4400N which only cause problems when the router isn't handing out DHCP.
That being said i would invest in a layer 3 switch ( SG300-10) would work fine. It supports LAGS - Vlans and capable of layer 3. ITS DOESN'T"t GIVE OUT DHCP so you'll need that. For the wireless clients i would get a actual AP (AP541N or Aironet series). This would be a better solution.
http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps10898/data_sheet_c78-610061.html
You can draw us out a topology and we can give better solution, but from your post above this is the way i would go. Also if you want to give us a call @ 1-866-606-1866 and speak with next available engineer; we can assist in recommending devices that would work best for you. They can consult with a (SME) if needed.
**Knowledge is power**
         Jasbryan

Similar Messages

  • Can't connect to wireless network with Dell Inspiron 1525 with Vista

    I set up a wireless network about a week ago, and have made it with the following security features: WEP, enable only certain MAC addresses to connect, and disabled broadcasting the SSID.  I have been able to use it just fine with my Mac computer using airport, but when I have tried to connect my roommates computer, a dell inspiron 1525 with vista, it can't connect.  I can locate the network but when I try to connect to the network, I get a message saying that for an Windows cannot connect to the network and that the Wireless association failed due to unknown reasons.  It then says to connect with your administrator, but that is me.  I have a minimal knowledge of computers just enough to be dangerous and am basically figuring this out as I go along.  If anyone has some advice for me, both my roommate and I will be very grateful.
    Thanks,
    - Jill
    Solved!
    Go to Solution.

    Sorry I am not sure if this is needed but I am using a WRT54G router ver.6.

  • Mountain lion 10.8.2 can not connect to windows NAS server Dell Sentinel

    I recently upgraded to 10.8 OS My office is connected to a NAS server Dell Sentinel WD4000. Everything was working fine until the upgrade from 10.7 to 10.8 Now when I "connect to server" Not one of my accounts can connect. All I get is wrong password. The server connects to every computer on the network except the 10.8 The server shows up as an icon on Shared Devices.
    Someone please help me. Apple has been useless.

    I hope this helps.  But, Apple has confirmed a significant bug in 10.7.4 that breaks SMB.  Their support says they are working on it, but they do not know when the fix will be released.  It has broken SMB at all sites I support including my own location where Lion server has the updated version as well.  Only AFP works but not consistently.  The suggestion is to restore 10.7.3 from a backup or wait until the fix is released.  SMB does work - but only when admin authentication is used on Mac servers - don't know about Windows Servers.  I do know the client side of Mac's also are affected with SMB issues.  Good luck!

  • What cable do i use to Connect my MBP to a dell monitor

    What cable do i use to connect my rMBP to my Dell monitor

    Assuming the Dell monitor has an HDMI input then you need one of these:
    http://store.apple.com/uk/product/H7128ZM/A/mini-displayport-to-hdmi-cable-2m?fn ode=51&p=1

  • Connect Sun Ultra2 to a Dell 19" LCD Monitor

    Hi
    Can you connect Sun Ultra2 to a Dell LCD Monitor 19" using a Sun Graphics adaptor HD15F
    Thanks,
    -Will

    The answer is probably "No".
    An Ultra-2 only has SBUS and UPA slots (no PCI slots), and few of the qualified graphics boards had HD15 connectors. There was no integrated graphics. All system administration could be done via command-line through its serial port.
    The default screen output of a Sun system is 1152x900 at a vertical refresh rate of 66Hz. The best you are likely to see on that PeeCee flat panel screen is a scrambled "something" that may eventually make your eyes hurt.
    When you say "Sun Graphics adaptor HD15F" are you are simply stating there seems to be a familiar graphics shape on the system or are you asking about some sort of adapter cable? That doesn't tell us the actual card that is in the system.
    Keep in mind that you are asking about hardware that is probably 15 years old.
    It may have been cutting edge back then, but it has been very much passed since that time.
    For a more precise answer, you will need to open the computer, remove the graphics board, and copy the part number from its barcode paper sticker. We would need the first seven digit (something such as 501-4790xxxx ).
    You could have posted this hardware question to the [Hardware Forum|http://forums.sun.com/forum.jspa?forumID=828] you know, or even just search that forum for whatever you might need. This topic has been discussed over there many times in the past five or six years.

  • Can I connect my iphone to a Dell 1907fp monitor via a usb to watch TV?  I cannot get it to work!

    Hello, I am trying to connect my iphone to a dell 1907fp monitor via a usb cable, but it doesn't go past the test screen.  Any pointers?

    Not possible with a USB dock connector cable.
    http://www.ehow.com/how_7665220_connect-monitor-iphone.html

  • VPN connection to WRVS4400N using a Samsung Galaxy tablet

    I have a Samsung Galaxy 10.1 tablet and have bee trying to connect to my WRVS4400N router with VPN through the "on board" software as well as with the Any Connect software from Cisco.  I have no issues at the moment using Quick VPN from my laptop.
    When using the Any Connect software I receive the following messages:
    Security warning: untrusted certificate
    AnyConnect cannot verify the identity of <IP address>.  Would you like to continue anyway?
    - Certificate does not match the server name.
    - Certificate is from an untrusted source.
    - Certificate is not identified for this purpose
    [Accept]  [Details]  [Cancel]
    If I select accept, the following error is received:
    "Error:  Connection attempt has failed due to server communication errors.  Please retry the connection".
    I have tried setting up the on board VPN with the Samsug Galaxy but every attempt has resulted in a time-out of the connection.
    Any assistance would be greatly appreciated.  Thanks.

    Hi Blair,
    The WRVS4400N only works with the QVPN software. The only small business router at this current time works with the Cisco any connect vpn is the SA500 series routers.
    I hope this helps.....
    Thanks,
    Tori Woods
    Cisco Support Engineer
    CCNA, CCNA Wireless

  • Connecting my MacBook Pro to Dell Monitor

    Hi, I have a Dell E228WFP 24 inch monitor and I have connected it to my MacBook Pro (October 2013, Non-retina, 13 inch) with a Mini DisplayPort to DVI adapter, and another adapter off eBay, which plugs into the VGA cable that is in the back of the Dell monitor. When I turn the monitor on, the screen remians black, then the monitor goes into power save mode. The Mac can find the monitor, and the Mac says the monitor is working perfectly.
    The monitor goes into power save no matter if I put it on Auto Detect or Digital imput, or Analog input.
    Please help!

    Searching on Amazon, I find the monitor has HDMI.  a Mini-Displayport to HDMI adapter from the Apple Store is a much better choice than any VGA adapter.  Also your machine will support audio over HDMI if there is audio on the monitor.  If not, that's immaterial for that monitor:
    http://www.amazon.com/Dell-E228WFP-Widescreen-1680x1050-resolution/dp/B001BKR5D8
    Anyway, HDMI carries the full digital signal.  So does DVI.  I for one prefer HDMI since it is less likely to fail connecting.

  • Can't connect Macbook Pro Retina to Dell P2715q 4k Monitor

    I received a new Dell 4k P2715q monitor on Friday.  It came with a mini DP to DP cable which I immediately hooked into the Thunderbolt port on my 15-inch, Mid 2012 Macbook Pro Retina.  It worked beautifully on Friday all through the day.  Was very happy with my purchase.
    Took the laptop home over the weekend and brought it back today.... plugged into my thunderbolt port again and nothing.... Go HDMI to the monitor's HDMI and it works but only up to 1080p in 30hz which is no good.  So the monitor still seems to be working but the Macbook won't recognize the monitor through the Thunderbolt (mini DP) port.
    Any thoughts?  Talked to Dell support which was worthless except to verify that the monitor didn't get fried over the weekend and also talked to Apple who suspected that it was maybe the mini DP cord that Dell sent with the monitor.  I can't believe that a cable went faulty over a weekend when no one else was in my office.....
    Thoughts?  Thanks ahead of time!

    Hey reinier67,
    Thanks for the question. I understand that you are experiencing issues connecting your MacBook to an HDTV. The following resource outlines some troubleshooting steps that may lead to a resolution:
    Apple computers: Troubleshooting issues with video on internal or external displays
    http://support.apple.com/kb/HT1573
    Thanks,
    Matt M.

  • Connecting MacBook Pro to a dell monitor

    Having a little dilemma trying to figure out how to connect a dell monitor to my MacBook Pro. (Mid 2012)   Dell monitor has a dvi-d connection. Not sure which apple connector I need and if I need to purchase a double ended male male dvi-d cable. Help!

    Hi,
    I am sure your problem must have been sorted out by now, but for all current and future buyers for the dell U2414H and having an apple computing device, mac, macbook, pro etc, the monitor works perfectly out of the box when I connected with a mini DP(thunderbolt port) to HDMI output (U2414H), it just ran out of the box, without any issues, it even worked simply for my bootcamp windows. So no need to fret before purchasing one, simply go ahead and get it, it's the Monitor with most appealing edge giving you only a screen to view at, I was also considering between the U2412M and the U2414H, I think I've made a great choice.
    Cheers,
    N

  • Connecting Air to external monitor (Dell)

    I am trying to help my boss connect his Air (2010 edition) to an old Dell monitor we have here at the office. I bought a Mini DisplayPort to VGA Adapter but when we connected everything his Mac screen didn't appear on the Dell. Is there something else we need to do? The Dell monitor is about 8-9 years old I think.

    HI, Wormo, and welcome to Apple Discussions. If the broken display cable hasn't shorted anything out and damaged the logic board (and it sounds as though things may still be working properly other than the display), you should be able to hit the F7 key at the top of your keyboard to toggle between extended-desktop mode and display mirroring mode. The latter, in which the external display shows the same thing as the built-in display, is what you want, since that should enable you to see your hard drive, desktop files, menu bar and dock on the external display. You are probably in extended-display mode now.

  • How do I connect my MacBookPro to my Dell U2412M 24" monitor?

    How di I connect my MacBookPro to my new Dell U2412M 24" monitor?

    If your MacBook Pro has a Mini DisplayPort or Thunderbolt port, use a Mini DisplayPort to DisplayPort cable.  If not, use a DVI cable.

  • Force RGB over HDMI connection??!! (Dell U2414H)

    Since Apple's support refuses to help me, nor do they seem to grasp incredibly basic technical information regarding monitors, I'm turning to you, dear forum.
    I just bought two brand brand and professional calibrated Dell U2414H monitors to use with my Mac mini workstation in an extended desktop environment.  ...even though Apple themselves erroneously told me I'd be able to daisy chain these monitors over the Thunderbolt connection using MiniDisplay Port 1.2 MST... (they were wrong, their GPU doesn't support DP 1.2)...  So, I resorted to plugging the second monitor into the available HDMI port.
    Problem:  The Mac OS will not send the right color space (RGB) over HDMI.  It sees the monitor as a TV for some reason, and will only send YPbPr... Therefore, my monitors that I paid extra to have calibrated perfectly, do not match.
    I ran this script: http://embdev.net/topic/284710#3027030
    but it didn't change anything.  I'm searching for new solutions now...
    Can anyone help?

    Here... I solved it:
    Dell U2414H Monitor - RGB COLOR ISSUE [SOLVED!] - The EASY way!

  • How can i connect my ipad2 to my dell pc?

    how do I start-up my ipad connecting to my dell computer to register and start synching music?

    Page 23 of the iPad 2 manual:
    http://manuals.info.apple.com/en_US/ipad_2_user_guide.pdf

  • Connecting Apple AE to a Dell D600 laptop

    How do we connect an Apple Airport Express (AE) to a Dell D600 (laptop)??
    After spending 2 frustrating hours trying to set it up, nothing but a blinking amber light!! We just want to connect it so we can listen to iTunes on our stereo. The Airport Utility program cannot detect the AE, no matter how many time we try to 'rescan', we even used an ethernet cable to try to hard-connect with no avail.
    Please any help or guidance is highly appreciated.

    Why are you trying to connect to the computer via bluetooth, and what are you trying to do when connected.
    This support document describes what Bluetooth profiles the iPhone supports. http://support.apple.com/kb/HT3647

Maybe you are looking for

  • Acrobat Reader x 10.0 - Cannot open pdf as a single file

    I am using Acrobat Reader x 10.0 on Win 7 64 bit OS. I save Filemaker 11.0 Reports as PDF Individual Single Files, to a Folder on my Hard Drive. On some occasions, I can have been able to open these Individual Reports files as a Single Files, each of

  • Trigger the  output  type

    Hello , I  forgot  to  create  a  condition  record  for  output  type  for  sales orders........ Is  there  any  program  that  I  can  retrigger  the  Output  type  now  for  existing  orders? Thanks and  best  regards L

  • Increase decimal places in the PO quantity and Price

    Hi All, Can the decimal places in the PO( ME21N) creation be increased more than 3 decimal places in quantity and price? I did changes in UOM's in CUNI, I increased the decimal places upto 14 but still it does not take more than three i-e., 0.001 max

  • Does OEM 2.1 support windows 2000 profesional

    Hi! I tried to install and configure oem 2.1 on windows 2000 profesional. so please let me know it's support oem for windows 2000 profesional. Thanks, Arvind

  • How long is the MSI motherboard Warranty??

    I can't find it anywhere on their web-site?