Connecting AX to mixed wired/wireless network

I've got a networking issue that I can't seem to solve and could use some help. I have a old house that, while not terribly large, has very thick, radio opaque walls.
I use a cable modem connected to an Airport Extreme which creates a wireless network within the house (which I extend around the house with a couple of Airport Expresses). I also have two computers wired via some VERY long CAT5e ethernet cables to the same Airport Extreme - a MacMini in my kitchen and a MacPro in my office (which is detached, across the yard from the main house). Right now I also use an Airport Express in my office to extend my wireless network for my clients who come to the office with laptops, etc. and also for my iPad. But the wireless signal is so weak out in the office that even with the Airport Express repeating it, it's very slow and spotty.
So, I bought an Ethernet switch, thinking I could split the Ethernet coming into the office and run one directly into the MacPro and the other into the Airport Express. I figure it's not hard to configure the Airport Express to create a NEW wireless network with the data coming in via Ethernet. However, what I want to do is create a node on my EXISTING wireless network (so my devices can see each other), just using data coming from the ethernet port instead of repeating the weak wireless signal that's reaching the office from the house. Is this possible? If so, how do I do this?
By the way, I have both old (G) AX's and well as a couple of new (N) ones. Right now the new ones are in the house and an old one is in the office, but I could move things around if it made things work.
Thank you.

Hey Bob,
I set up the Airport Express as you described and, while it worked at first, I'm running into some difficulties. Basically, the AX unit tends to disappear from the network after about an hour. It's very strange because, like I said, it works at first and I have great signal out in the office then... poof!... it's gone. And it doesn't just disappear from the wireless network. Both my MacPro and MacMini (which are connected via ethernet) can't see it either. I have to unplug/replug the unit to get it to show up again.
I thought it might be the particular unit. But I've tried two AX (G) units and my old AirPort Extreme (G) UFO shaped router all in the same bridge configuration and they exhibit the same behavior -- working at first then dropping off the network and requiring a reboot to reappear.
Do you have any thoughts? I'd be most grateful.

Similar Messages

Remote can't find iTunes on mix wired/wireless network

I am trying to control music from a iMac running iTunes using the iPhone Remote app. I've previously done this successfully with a wireless only network (using the Airport Express wifi to join my existing wifi network etc).
However, since introducing D-Link Homeplugs into my network, I am unable to 'see' the iTunes library from the Remote app when I connect wirelessly to the airport express.
My hardware is configured as follows:-
*Netgear Router (wireless disabled) -> Homeplug power network -> iMac running iTunes*
And elsewhere on the Homeplug network, I have:
H*omeplug power network -> Airport Express [set up as wireless access point]*.
If I connect the Express to the iTunes machine directly - leaving the wireless access details the same - it all works fine. If I move the Airport Express and reconnect over the Homeplug network, the Remote fails to 'see' the library, although I can still send music over the network (using the iTunes interface on the iMac) to the remote speakers.
My network uses the router as a DHCP (range 192.168.0.x mask 255.255.255.0), Airport Express is connected to Homeplug ethernet with a static IP (in the same range) and provides wireless access (unsecured for now while i get this working). The iMac has a static IP (in the same range). If I swap the iMac for a PC (XP - using DHCP from the router for IP), I get the same result. If I use an iPhone network application to view the network (connected by the wifi access point on the AX) then I can see all the machines on my network as I would expect.
To reiterate, if I cable this network directly (either AX->iMac or AX->hub->iMac) then it works. As soon as I go AX->Homeplug power network->iMac then the Remote app loses sight of the library.
I wouldn't expect any firewall on the wired->wireless networks on my router (a Sky branded Netgear 934g). I also didn't think that the Homeplugs would block.
So does anyone have any ideas why the Remote application loses sight of my iTunes library when connecting via Airport Express cabled into a Homeplug ethernet network ?
Thanks for any help because I miss my music
cheers,
Tim

Hello,
This is the same for me. Impossible to find a solution after.
Can you help us.
Thank

Connecting HP Laserjet P1102W to wireless network (then getting drivers!)

Hi,
My macbook pro and HP LASERJET P1102W seemed to be communicating just fine when I had snow leapard. Post update to Mountain Lion, problems.
I have gotten the printer to work when connected via USB, however not consistently. (Often it cannot recognize when paper tray is filled, cannot do two sided printing and has other issues perhaps connected to the fact that software is missing?)
I have read the documentation on HP site, noting that the only way to install drivers is via a network connecton and airprint which requires a network connection.
Not sure this is the right place to ask this, but I will for now:
How do I connect my printer to my network, which is a new home network as I just changed from DSL to Cable?
Note: I had not previously ever connected my printer to my wireless network and set it up to work with Airprint, though that is one of the reasons I bought it.
Once I do connect the printer to my wireless network, perhaps then I can try to follow the steps on the HP site   http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03425022&cc=us&dlc=en&lc=en &os=4142&product=4110396&sw_lang=
If anyone has experience with the above, I would love to hear it!
Final question: Is plugging the printer into the back of the new cable modem via ethernet or USB perhaps a way to put it on the wireless network? Not a convenient location, but if only alternative, I would try it.
THANKS!
Ani

Dear Happy-to-Help,
I appreciate you logging in to help. I shall give this a shot in the next couple of days when I have more time and let you know how it goes.
I have been quite frustrated by the fact that HP says if the HP Laserjet P1102W has worked fine with Snow Leapord and one upgrades to Mountain Lion, all the drivers will be automatically upgraded/updated (or whatever the term). That has not been the case at all.   It took quite a bit to even get my computer and printer to talk to one another via a USB connection—with none of the functions of the printer (as noted above) working properly to this day.
I hope your suggestion works. Will be back in touch to let you know.
Ani

Problem connecting MBP to established Linksys wireless network

just got MBP 2.16 (my first mac!). Having trouble connecting to my established linksys wireless network. I have the BEFW11S4 (V.2) etherfast wireless access point + cable router with 4 port switch. Currently have 128 encryption enabled. The linksys router is broadcasting its ID (I can see "linksys" on my mac) but it seems to not accept the password. I tried entering the 26 WEP key, the passphrase, the WEP key in quotes, the WEP after a $ sign... all to no avail. please APPLE community, help out a mac noobie before i have to turn back to Bill Gates....
Dell Dimension 8200, MBP 2.16 Mac OS X (10.4.6) 2 GB SDRAM

To find the IP address or the status, go to system Preferences then network. It will show you the status of any internet connections. You should see one for Airport, it will either show a green light and say 'Airport is connected to the internet' (or something like that) or a red light and say 'Airport is is active but not connected' (something like that). If you double click on Airport or click 'Configure' you will see tabs, click on TCP/IP and it will show all of your details including your IP address.
As for the other, it always refers to wireless networks as 'Airport' and that response is the standard response from a Mac.
the password should be typed in the hex section, not sure about the $ sign. I've never had to do that before. But if you can't connect even with no encription then I would think it is another problem. I would turn off the encription until you can at least get connected and then you can worry about the security afterwards.

I can't make my iphone 4 forget the hpsetup network which keeps showing up at work. My phone won't automatically connect to my company's wireless network.

I can't make my iphone 4 forget the hpsetup network which keeps showing up at work. My phone won't automatically connect to my company's wireless network. I have to reselect it everytime I come to work.

Settings/General/Reset - Reset network settings will "forget" all WiFi networks so you can select them again.
If the problem with your company network is not solved by doing this, are there multiple sites that have the same network name for the company network? Or is it the default network name for the router type (e.g., DLINK, LINKSYS, etc)? If so, this is what is causing the problem and there is no solution other than convincing IT that it is a bad idea to have duplicate network names.

Graphite Connects to Someone Else's Wireless Network

When I startup my eMac (10.4.8) I sometimes cannot connect to the internet via Airport. I discover, upon launching Internet Connect, that I am connected, but not on our wireless network. Instead, Airport shows me connected on something called "linksys" (which I assume is a neighbor's wireless network), and the signal is very weak. I can switch to our network via Internet Connect & all is well, but it's a hassle having to go through this every time. It used to be that I'd immediately be connected to our own wireless network & Airport upon startup. Help! How can I "teach" my Airport to always connect via OUR network & not "linksys"???

Try each of the following, in order, until resolved:
1. Run the Disk Utility to repair Disk Permissions.
2a. Delete Preferred Network(s)
- System Preferences > Network > AirPort > Configure
- In the "By default, join:" pull-down menu, select "Preferred networks"
- Delete the network(s) you regularly use from the list
2b. Delete AirPort Keychain Entries
- Launch the "Keychain Access" application located in Applications/Utilties.
- Click on the "Kind" filter at the top, and look for any "AirPort network password" entries...and delete them.
- Restart, or log out then back in.
2c. Add Preferred Network(s)
- System Preferences > Network > AirPort > Configure
- In the "By default, join:" pull-down menu, select "Preferred networks"
- Add the preferred network(s) using the "+" button.
- Restart or log out then back in.
3. Create a New User Account
- Create a new user account.
-- System Preferences > Accounts
-- Click "+" to add a new account
- Log off, then log back on with the new user account.
- Try connecting with the AirPort.

Connecting HP Officejet 6100 to wireless network with OSX 10.9.5

Running OSX 10.9.5.
I'm trying to connect HP Officejet 6100 to wireless network without HP software since the software claims it is not compatable with my OS.
The printer works fine when connected via USB.

Hi @dj2thew,
Thank you for visiting the HP Support Forums! I see you are trying to add your HP Officejet 6100 to your Mac running the Mavericks 10.9.5 Operating system.
Because you are using the Mavericks OS X you must install the printer using the Apple Updates. Please click on the link below, this document explains how to install the print driver on a Mac for a USB or a network connection. The OS X v10.9 Mavericks driver for your printer is available through Apple Software Update (ASU). Additionally, you can perform basic print jobs using AirPrint without installing a driver.
OS X v10.9 Mavericks: Installing and Using the Printer on a Mac
Once you have installed the OJ 6100, you may notice the features you once had are limited or there are workarounds, for scanning with or without HP Software see below:
How to Scan: OS X v10.9
I hope this helps!
Thanks again,
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

HP Photosmart c309 and printing from Vista laptop on wired/wireless network

Ok going to be as thorough at possible here.
Its a brand new HP Photosmart c309 which I received this past Weds, so far so good both my Wife and I are enjoying it. Now I have it wired into my home network which consists of a Linksys switch in our home office and Netgear wireless router in the basement. The Linksys switch is wired to the router in the basement for internet/network connection...I have my Dell workstation running Windows XP SP3 (with all the latest patches from Microsoft, Mcafee AV) and the photosmart printer wired to the switch. I installed the HP software and drivers from the disk on the XP workstation and all is well...prints, scans and I'm able to view the printer settings, ink levels and what not.
NOW my Wife's Dell Vista laptop (which is patched to the latest from Microsoft, Mcafee AV) is getting really annoying. First I hate Vista but that’s another story...the Vista laptop connects to our home network via the wireless network through the Netgear router. So I followed the same steps as my XP workstation, it finds the printer during setup and all is well till the part when it wants to send a test page...so I opt to skip the photo test page and just do a standard one. Well it "sends" a test page or at least it looks like it does but nothing comes out of the printer (ie no activity from printer). The printer icon shows up in the system tray in the lower right hand corner of the screen near the time and when I put the mouse pointer over the icon is says "0 in queue" so I double click the icon to see if I can get more info and nothing happens. Right click the icon and choose open all active printers and again nothing. The printer icon is in the system tray for about 10-15 seconds and then disappears.
So I'm a little confused here, I check the printer in "printers & faxes" and both it and the fax part are listed...the printer even says it’s in "ready" status. I start the HP solution software on the laptop and I am able to scan from the printer to the Vista laptop fine, I'm able to view printer settings, network settings, ink levels and what not. I JUST CAN'T printer to it.
I tried another test page from the printer properties within Windows, again the icon shows up in the system tray and it says "0 in queue" and the icon disappears after 10-15 seconds. I then try to print a picture using the HP software and the same thing...icon shows up in system tray "0 in queue" and it disappears.
Did I do something wrong or am I missing a special step for Vista machines? I did uninstall and reinstall software/drivers and manually removed the printer and then reinstalled everything with no luck and no change...still acts the same.
I'm lost at what else to try. I think I tried the obvious stuff. I've searched the web to come up blank with a similar situation like mine...I've seen others complain about printing 1 page documents and the printer prints 3,6,16 pages at a time which is the opposite from my situation.
Any input/advice would be greatly appreciated.
Thanks in advance,
Bruno

Have you received an answer to this question? I'm having the exact same problem. Spent 4 hours on the phone with HP tech support and no solution.

Connecting to server residing inside wireless network

I'm trying to connect from a program on an outside machine to a ServerSocket listening inside a wireless network. I'm running into a snag due to the way the system works. It runs fine on other setups, but I don't understand the issues involved with getting around the proxy (I'm not even sure what the right terminology is here).
Here's how it (should) work:
Program A - the one on the wireless network - creates a server open on a specified port.
Program A contacts Program B, which is already listening on an established port.
Program B records A's server contact information.
Programs C, D, etc. contact B to retrieve A's server contact information, and proceed to communicate directly C to A.
This was working fine, until we threw the wireless network into the mix. Our 1st hurdle was the DHCP, and we managed to obtain the actual IP address of the network as opposed to the internally-supplied IP used by the machine inside running Program A.
The problem we're hitting now is that I've got this server running on port X inside the network, but once it connects to the outside world it's being channeled through a different port. Okay, I can send a message back to the router of the wireless network, but I don't understand how to redirect it back to the port that the server is listening on in Program A.
So my question is: how do I connect to a socket inside a network such as this? Or is this a network configuration issue?

"Wireless" isn't your problem. DHCP and firewall/router are.
The machines "inside" this kind of DHCP setup don't exist from the outside - all the outside can see is the external IP addr of the firewall. You want/need a well-known port on your firewall to map (always) to the well-known port on the server machine that's inside your network. Getting that to happen is heavily dependent on the kind of software your firewall/router is running.
This question doesn't have anything to do with Java per se - you'd be having exactly the same problem no matter what language you were writing in. I think you'll have more luck posting the question to a forum for whatever hardware you're using for your router.
Good luck,
Grant

Airport Express Problem with Wired/Wireless networks simultaneously

Hello,
I'm having trouble maintaining a connection with my AX (2012) in a work environment. Basically, I have a Win 7 laptop connected via ethernet to the internet/corporate net. I have configured the AX to create a separate wifi network that does not connect to the internet. In order to connect to the AX, I have to disable both the Ethernet adapter and the WLAN adapter, enable the WLAN adapter, connect it to the AX's network, and wait for it to show up in the utility. Only then can I re-enable the ethernet adapter for internet access. Then, inevitably, the connection dies within 15 minutes and I have to repeat the whole process.
Can anyone tell me what's going on here? Is the wired network interfering with the wireless network? Is something configured wrong? Below is the output from ipconfig/all, if that helps. The AX is configured with a 169.254 range. IP address and behaves the same way whether the IP address is auto or manual, and there is no difference if the signal roams channels or is fixed to a single channel (I've played with them all).
Thanks in advance for your help.
Wireless LAN adapter Wireless Network Connection:
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : DW1501 Wireless-N WLAN Half-Mini Card
   Physical Address. . . . . . . . . : 68-A3-C4-0C-CE-5B
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   IPv4 Address. . . . . . . . . . . : 10.0.1.2(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : Thursday, December 06, 2012 2:32:22 PM
   Lease Expires . . . . . . . . . . : Friday, December 07, 2012 2:41:43 PM
   Default Gateway . . . . . . . . . : 10.0.1.1
   DHCP Server . . . . . . . . . . . : 10.0.1.1
   DNS Servers . . . . . . . . . . . : 10.0.1.1
   NetBIOS over Tcpip. . . . . . . . : Enabled
Ethernet adapter Local Area Connection:
   Connection-specific DNS Suffix . : XXX.com
   Description . . . . . . . . . . . : Intel(R) 82577LM Gigabit Network Connecti
on
   Physical Address. . . . . . . . . : 5C-26-0A-40-37-A9
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   IPv4 Address. . . . . . . . . . . : 3.197.129.227(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.254.0
   Lease Obtained. . . . . . . . . . : Thursday, December 06, 2012 2:42:43 PM
   Lease Expires . . . . . . . . . . : Thursday, December 13, 2012 2:42:42 PM
   Default Gateway . . . . . . . . . : 3.197.128.1
   DHCP Server . . . . . . . . . . . : 3.156.134.20
   DNS Servers . . . . . . . . . . . : 3.156.130.30
3.156.130.130
3.23.190.40
                                       3.23.192.43
   Primary WINS Server . . . . . . . : 3.156.130.30
   Secondary WINS Server . . . . . . : 3.156.130.130
   NetBIOS over Tcpip. . . . . . . . : Enabled

Here goes - read this through completely and see if it makes sense:
1. Reset the Express to factory settings by unplugging it and plugging it back in while holding in the reset button - release the button when the light starts blinking - then wait for the light to blink slowly indicating factory default.
2. Disable the wireless and enable the ethernet on the laptop and connect an ethernet cable to the WAN port (the circle of dots) of the Express and use the AU toset it up in bridge mode to create a wireless network with a name of your choice - you don't really need a password but you can assign one if you wish - if you do not use a password you will have to choose to ignore the error message for no security.
3. Accept all other defaults and ignore any messages about not having an internet or ethernet connection and update or finish the setup - if you get a blinking amber light, open the AU and correct any error messages.
4. You can now disconnect the ethernet cable and disable the ethernet on the laptop and enable the wireless so you can stream iTunes to the Express - the laptop must stay wireless to do this - you can not accesss both at the same time - you can also use an iPhone or iPad or iPod to use Airplay and then you can use the laptop via ethernet for the internet.
5. To access the Express from now on, you have to use the AU wirelessly from the laptop.
The above is assuming that you don't currently have wireless in your office - the other alternatives are:
1. To hardwire the Express and have it create a wireless network and access the internet - you could then use your laptop wirelessly or wired to connect to the Express and use Airplay and your pc at the same time.
2. If your office has wireless, you can set up the Express to "join" the existing network - you can then do the same as in number 1.
I hope this helps - everyone's situation is different - the above scenarios work for me - you might have to do some tweaks but the info is there - let me know if you have any questions.

Wired & wireless network

Hi There,
We currently have a cable modem and 2 airport express (old type that plug directly into power socket) working together.
However would like to:
have a wired network - i have installed cat5e cables to tv, pvr, dvd player etc
AND
have a wireless network
I am confused about switches and routers?
What hardware do i require to make this work?
I know i need a router but can the airport express work as a wired router or just a wireless router?
Thanks,
Susan

Yes you just need to connect the wireless router to the cable modem first then to your computers. The wireless router should have some LAN ports on the back that you can use to connect your two computers to. Then you can also connect to the wireless with your third computer as long as it's within range. What happens is the router regardless if it has wireless or not will establish a single network connection to the internet via cable modem. Then the router creates a local network for all of your computers and routs all the connections through the cable modem. It may take some configuring but that's how it works.
George

Can't Connect OfficeJet 7410 to new wireless network - used to work on old one

Hi, I'm on a Mac OS. I just upgraded my wireless network to use an airport extreme. I have a verizon fios router - same as I had when it used to connect. The only change was adding the airport extreme. Now, the officejet 7410 all-in-one will not connect to the wireless connect. It SEES the name of the network, and asks me for a WEP Key, which it didn't used to do. It used to ask me for the network password. I found the WEP key on the router and it acts like it is trying to connect but takes a long time and then gives me an error. One time it never gave me an error and seemed like it had worked, but was not connected. It just gave up.
My configuration page indicates offline with no active connection and wireless status disconnected.
I restarted everything with no change. I don't know why it would be asking me for a WEP key this time and then not accept it but that was the first indication that something was different when it didn't ask me for the network password.
Also, as a separate issue but related. In trying to fix this, I deleted my drivers to reinstall and see if I started over that it would work. That created another problem in that now it seems that HP no longer supports a driver for this printer. Is that even possible? It's not that old. It says it does not exist on the software update. Please help!

Hi YSJA,
I'm sorry to hear you've had problems accessing your Officejet 7410 since adding the AirPort Extreme to your home network.
I have included a link to HP's Wireless Printing Center troubleshooting section. It has section, "Was anything changed or updated on your router recently?" that has detailed steps to help you resolve the issue.
Wireless Printing Center Troubleshooting
http://www.hp.com/global/us/en/wireless/troubleshooting.html
Regards,
Happytohelp01
Please click on the Thumbs Up on the right to say “Thanks” for helping!
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
I work on behalf of HP

Connecting MacBook to printer via wireless network

I have a wireless network via cable modem with some PCs attached and a printer but am having trouble connecting my new MacBook to the HP LaserJet 2100 printer via wireless. I do not have airport express and not sure I need it to have the MacBook print to this printer. Please advise.

Hi topgunner,
How is the printer connected? Are you trying to share it via a PC through wireless? Or is it connected directly to a router/hub that is enabled for printer sharing?

How to Connect Airport Express to Existing Wireless Network (Client Mode)

I am posting this for everyone tearing their hair out trying to connect the Airport Express to your own existing home wireless network. After spending 2 hours last night installing this on my father-in-law's home network, I hope to be able to save someone else the agony we went through.
So here's the situation:
Say you already have your own home network set up, and all you want is to be able to use AirTunes to play music off iTunes into your speaker system. And, you don't need the printer sharing capability nor creation of another wireless network (2 of the features of Airport Express). Then this solution is for you - read on.
Unfortunately, Apple's user manual is very unclear how to connect Airport Express to your own network. When you look at the picture diagram they provide, they show Airport Express picking up its signal from another Apple-oriented base. This can make you think you need to buy another piece of hardware to make it work. DON'T If you read through the manual, the Support section here, etc., you will hear lots of talk about "Client Mode" - and that this is the only way to get it to work. Nice - but no one really tells you how to set up the Airport in client mode.
Do yourself a favor, toss that user manual aside and run these steps.
(Note: These directions assume your DSL/Cable Modem is hooked up to a wireless router or acts as its own wireless router)
1. Get a cat5 Ethernet cable (anything but an orange cable - that's a crossover cable) like you would use to connect your PC to your router to pick up the Internet.
2. Connect the Ethernet cable to the router on one end, and to the Airport Express unit on the other end.
3. Plug in your Airport Express unit to the wall (this will not necessarily become its permanent location - you will be able to move it later). The light will glow solid Amber for about 30-45 seconds while it starts up, then blink Amber. At this point, the unit is ready to operate.
4. Install the CD to the PC where your iTunes music is stored. This should be painless. Once you open the program, it should detect the Airport unit.
5. At this point, the on-screen wizard will present you with your options, and walk you through the setup. This is much like the user manual describes - and you should be good to go form here forward.
Some pointers:
- When asked if you want to create a new network, join an existing network, or connect via Ethernet, choose the middle option for joining an existing network. You will need to know the name of your network, the password to connect to the network (if present), and the type of encryption used on the network (e.g. WEP, WPA, etc.). Side note, WPA is recommended, as it is a higher level of security than WEP. You will be able to configure the Airport Express unit to automatically login to your network.
- I would recommend, when creating a password for the Airport Express unit, use the same password as your network, to avoid confusion.
6. The very last step will ask you to save the settings to the Airport Express. Here's the kicker - when you save the settings, you are TRICKING the Airport Express into no longer acting as a network broadcaster, but instead being a "slave" to your own network. What do I mean? You will lose the connection from your PC to the Airport Express - an error message will pop up telling you the unit can no longer be found. While you might think you did something wrong, you actually were successful!
7. Unplug your Airport Express, and disconnect the Ethernet cable from your router and the Airport unit. This will no longer be needed.
8. Go to your desired location where you want to plug in your Airport Express unit. Before plugging it in, connect your Audio cable from the Airport Express to your audio receiver. Once that is connected, then plug in the Airport Express unit. The light will glow solid Amber for 30-45 seconds while it loads, and then will blink Amber for a brief period of time before turning solid GREEN. When this happens, you have successfully connected the Airport Express to your home network!
9. Go back to your PC with iTunes. Open the Airport software - you should now have a listing for your Airport Express unit in the upper left. Click on this, and the wizard will guide you through connecting - you will need the password you created for the unit. You only need to go through this wizard once, and when finished, the software will tell you that can now use iTunes with your Airport unit.
10. Open iTunes. On the lower right, you will see a dropdown for Speakers, and it should be defaulted to My Computer. Click on that drop-down, and you will see the name of your Airport unit. Click on that name, and now your music will broadcast to the Airport unit!
11. Play a song in iTunes. Go to your audio receiver, and connect it to the channel for your external connection to the Airport Express unit. You should hear your music from iTunes. CONGRATULATIONS! =)
I hope these instructions were helpful - I am happy to answer any questions, so feel free to contact me, *******************@*****.**.
<Edited by Moderator>

Thanks for the detailed directions. You are absolutely correct in stating that people should toss the user manual; it's pretty worthless. I have had a problem setting up my new Airport Express as I have described in an earlier post - http://discussions.apple.com/thread.jspa?threadID=1839873&tstart=45
One quick question - does using your setup process set the AE up as part of a distributed network where the AE is acting as a wireless router where it is extending the range of your network? Or, is it simply a wireless connection to your stereo for iTunes? I am interested in having both, since my AE will be at the other end of the house from the main wireless router.
Thanks

Setting up HP Officejet 6500A; not sure how to connect to web w/ home wireless network

I have a small home wireless network. I set the printer up today but it says that I must connect to the internet (fax part is working). The only desktop I have, I keep off most the time and just use my laptop (which is for work so I can't set the printer up to this).
Is there a way to connect the printer directly to my router? They are only a few feet from one another; however, I have no clue how to do it and the instructions manual didn't tell me much. Do I need a phone line? What would I use to connect the two?
This question was solved.
View Solution.

Use an Ethernet cable, available in any tech store, online or even Target will have them.
Plug it into the back of the printer and router. You should be able to add the printer to your laptop. Let me know what operating system you have and I can help.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Connecting AX to mixed wired/wireless network

Similar Messages

Maybe you are looking for