Connecting Cisco AIR-CAP2602E over WAN with WLC - Procedural Details

Hi,
I have a Wireless LAN Controller Installed in one of the subnets where some AIR-CAP2602E's are connected with the WLC. WLC acts as DHCP for the AIR-CAP2602E Devices.
I have additional AIR-CAP2602E access-points at other location (Subnet) and Need to connect them with WLC. 
Challange faced by me is creating DHCP on Cisco 2950 (L2) or 3750 (L3) with DHCP option 43. Can any one has detailed configuration of enabling DHCP for specific VLAN on Cisco L2 and L3 Devices. 

If you have control of the DNS environment for these network segments, just make an entry for :
cisco-lwapp-controller aliases cisco-capwap-controller (IP list) as the CAP will hunt for those two name sets.
My WLC provides DHCP support only to the wlans supported by the AP but not the AP it self..
hope this helps

Similar Messages

  • I am using several Macs running Yosemite. I was recently "upgraded" to Xfinity's new cable modem which can support both 2.5Ghz and 5Ghz networks at the same time. Actually I can connect to the internet over both with a satisfactory bump in speed for

    I am using several Macs running Yosemite. I was recently “upgraded” to Xfinity’s new cable modem which can support both 2.5Ghz and 5Ghz networks at the same time. Actually I can connect to the internet over both with a satisfactory bump in speed for the Ghz. However when I connect to the 5Ghz the Time capsule disappears from the Airport Utility and claims to be Not Found. Is there something I have done wrong or just a Yosemite Teething Problem

    First restart your mac and try again.
    It could be
    that the router and the TC are interfering wirelessly with each other.
    You can check this by pressing the option key while clicking on the wireless icon on your screen
    Open Wireless Diagnostics
    enter your user password
    Press CMD 4 then Scan
    You will see all the wireless channels being used in your location and you can check if they are on the same channel
    Make the SSID for the TC simple like MyTC
    Set 5Ghz to auto
    Update the TC
    Try again
    Ted

  • Cant Connect Cisco AIR-CAP 3602 with 2504 controller

    Im trying to have one of our APs join our controller. No matter what I do, i cant get it to join the controller.
    The controller has the right OS, I had to upgraded it 7.4 to support the 3600...
    Both the controller and the AP has the same time and date.
    But Im getting this from my AP:
    *Oct 30 14:49:26.043: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Oct 30 14:49:26.055: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *Oct 30 14:49:26.055: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
    *Oct 30 14:49:26.067: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Oct 30 14:49:26.083: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Oct 30 14:49:27.055: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Oct 30 14:49:27.095: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
    *Oct 30 14:49:27.103: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Oct 30 14:49:28.087: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Oct 30 14:49:28.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Oct 30 14:49:28.131: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Oct 30 14:49:28.139: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    *Oct 30 14:49:28.147: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Oct 30 14:49:29.131: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Oct 30 14:49:29.139: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Oct 30 14:49:29.167: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Oct 30 14:49:30.167: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Oct 30 14:49:36.083: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Oct 30 14:49:36.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.1.0.50 peer_port: 5246
    *Oct 30 14:49:36.411: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.1.0.50 peer_port: 5246
    *Oct 30 14:49:36.411: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.0.50
    *Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
    *Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
    *Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.1.0.50
    Anyone can help me please?
    Thanks....

    AP is connected directly to one of the ports on the 2504 controller.
    I can move it to a POE switch, if needed.
    Here is the output after I boot up the AP:
    IOS Bootloader - Starting system.
    flash is writable
    FLASH CHIP:  Macronix Mirrorbit (00C2)
    Xmodem file system is available.
    flashfs[0]: 43 files, 9 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31997952
    flashfs[0]: Bytes used: 16767488
    flashfs[0]: Bytes available: 15230464
    flashfs[0]: flashfs fsck took 16 seconds.
    Reading cookie from SEEPROM
    Base Ethernet MAC address: 4c:00:82:77:32:7b
    Ethernet speed is 1000 Mb - FULL Duplex
    Loading "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-mx.152-4.JA1"...###########################
    File "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-mx.152-4.JA1" uncompressed and installed, entry point: 0x2003000
    executing...
    Secondary Bootloader - Starting system.
    Xmodem file system is available.
    flashfs[0]: 43 files, 9 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31997952
    flashfs[0]: Bytes used: 16767488
    flashfs[0]: Bytes available: 15230464
    flashfs[0]: flashfs fsck took 8 seconds.
    Base Ethernet MAC address: 4c:00:82:77:32:7b
    Boot CMD: 'boot  flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-xx.152-4.JA1;flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-mx.152-4.JA1'
    Loading "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-xx.152-4.JA1"...###############################
    File "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-xx.152-4.JA1" uncompressed and installed, entry point: 0x2003000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C3600 Software (AP3G2-K9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2013 by Cisco Systems, Inc.
    Compiled Tue 30-Jul-13 22:57 by prod_rel_team
    Initializing flashfs...
    flashfs[3]: 43 files, 9 directories
    flashfs[3]: 0 orphaned files, 0 orphaned directories
    flashfs[3]: Total bytes: 31739904
    flashfs[3]: Bytes used: 16767488
    flashfs[3]: Bytes available: 14972416
    flashfs[3]: flashfs fsck took 8 seconds.
    flashfs[3]: Initialization complete.
    flashfs[4]: 0 files, 1 directories
    flashfs[4]: 0 orphaned files, 0 orphaned directories
    flashfs[4]: Total bytes: 11999232
    flashfs[4]: Bytes used: 1024
    flashfs[4]: Bytes available: 11998208
    flashfs[4]: flashfs fsck took 1 seconds.
    flashfs[4]: Initialization complete.
    Copying radio files from flash: to ram:
    Copy in progress...CCCCC
    Copy in progress...CCC
    Copy in progress...CCCC
    Copy in progress...CCCC
    Copy in progress...CC
    Uncompressing radio files...
    ...done Initializing flashfs.
    Radio0  present 8764 8000 0 A8000000 A8010000 0
    Rate table has 244 entries (64 SGI/104 BF variants)
    Radio1  present 8764 8000 0 88000000 88010000 4
    Radio2 not present 0 0 0 0 0 8
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CAP3602I-A-K9 (PowerPC) processor (revision A0) with 180214K/81920K bytes of memory.
    Processor board ID FTX1731GQYY
    PowerPC CPU at 800Mhz, revision number 0x2151
    Last reset from power-on
    LWAPP image version 7.5.102.0
    1 Gigabit Ethernet interface
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 4C:00:82:77:32:7B
    Part Number                          : 73-14521-02
    PCA Assembly Number                  : 800-37501-02
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC17273HG4
    Top Assembly Part Number             : 800-35852-02
    Top Assembly Serial Number           : FTX1731GQYY
    Top Revision Number                  : C0
    Product/Model Number                 : AIR-CAP3602I-A-K9
    % Please define a domain-name first.
    Press RETURN to get started!
    *Mar  1 00:00:11.355: FIPS IOS test Image Checksum successful
    *Mar  1 00:00:11.355: FIPS IOS test Crypto RNG DEK Key Test successful
    *Mar  1 00:00:11.355: FIPS IOS test SHA-1 successful
    *Mar  1 00:00:11.355: FIPS IOS test HMAC-SHA1 successful
    *Mar  1 00:00:11.355: FIPS IOS test AES CBC 128-bit Encrypt successful
    *Mar  1 00:00:11.355: FIPS IOS test AES CBC 128-bit Decrypt successful
    *Mar  1 00:00:11.355: FIPS IOS test IOS AES CMAC Encrypt successful
    *Mar  1 00:00:11.355: FIPS IOS test IOS CCM Encrypt successful
    *Mar  1 00:00:11.355: FIPS IOS test IOS CCM Decrypt successful
    *Mar  1 00:00:11.387: FIPS IOS test RSA Signature Generation successful
    *Mar  1 00:00:11.391: FIPS IOS test RSA Signature Verification successful
    *Mar  1 00:00:11.391: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:11.391: %IFMGR-7-NO_IFINDEX_FILE: Unable to open nvram:/ifIndex-table No such file or directory
    *Mar  1 00:00:11.847: Registering HW DTLS
    *Mar  1 00:00:14.647: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:18.327: FIPS RADIO test AES 128-bit encrypt for TX on Dot11Radio 0 successful
    *Mar  1 00:00:18.327: FIPS RADIO test AES 128-bit CCM encrypt on Dot11Radio 0 successful
    *Mar  1 00:00:18.327: FIPS RADIO test AES 128-bit CCM decrypt on Dot11Radio 0 successful
    *Mar  1 00:00:18.327: FIPS RADIO test AMAC AES 128-bit CMAC encrypt on Dot11Radio 0 successful
    *Mar  1 00:00:18.327: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:24.451: FIPS RADIO test AES 128-bit encrypt for TX on Dot11Radio 1 successful
    *Mar  1 00:00:24.451: FIPS RADIO test AES 128-bit CCM encrypt on Dot11Radio 1 successful
    *Mar  1 00:00:24.451: FIPS RADIO test AES 128-bit CCM decrypt on Dot11Radio 1 successful
    *Mar  1 00:00:24.451: FIPS RADIO test AMAC AES 128-bit CMAC encrypt on Dot11Radio 1 successful
    *Mar  1 00:00:24.451: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
    *Mar  1 00:00:26.811: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C3600 Software (AP3G2-K9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2013 by Cisco Systems, Inc.
    Compiled Tue 30-Jul-13 22:57 by prod_rel_team
    *Mar  1 00:00:26.811: %SNMP-5-COLDSTART: SNMP agent on host AP4c00.8277.327b is undergoing a cold start
    *Jul  4 23:55:50.035: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Jul  4 23:55:50.035: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Jul  4 23:55:50.051: %PARSER-4-BADCFG: Unexpected end of configuration file.
    lwapp_crypto_init: MIC Present and Parsed Successfully
    *Jul  4 23:55:50.191: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Jul  4 23:55:50.855: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
    *Jul  4 23:55:51.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Jul  4 23:55:51.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Jul  4 23:55:51.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Jul  4 23:55:53.319: FIPS HW test SHA-1 successful
    *Jul  4 23:55:53.319: FIPS HW test HMAC-SHA1 successful
    *Jul  4 23:55:53.319: FIPS HW test AES CBC 128-bit Encrypt successful
    *Jul  4 23:55:53.319: FIPS HW test AES CBC 128-bit Decrypt successful
    *Jul  4 23:55:53.819: FIPS HW test SHA-1 successful
    *Jul  4 23:55:53.819: FIPS HW test HMAC-SHA1 successful
    *Jul  4 23:55:53.819: FIPS HW test AES CBC 128-bit Encrypt successful
    *Jul  4 23:55:53.819: FIPS HW test AES CBC 128-bit Decrypt successful
    *Jul  4 23:55:53.819: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed
    *Jul  4 23:55:53.819: DPAA Initialization Complete
    *Jul  4 23:55:53.819: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
    *Jul  4 23:55:54.819: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up%Default route without gateway, if not a point-to-point interface, may impact performance
    *Jul  4 23:56:13.191: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Jul  4 23:56:14.279: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Jul  4 23:56:15.279: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Jul  4 23:56:15.371: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Jul  4 23:56:16.371: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Jul  4 23:56:18.895: Logging LWAPP message to 255.255.255.255.
    *Jul  4 23:56:23.627: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.1.150, mask 255.255.240.0, hostname AP4c00.8277.327b
    Translating "CISCO-CAPWAP-CONTROLLER.pti.local"...domain server (10.3.1.32)
    *Jul  4 23:56:34.559: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Jul  4 23:56:34.567: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.pti.local
    *Jul  4 23:56:44.567: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Oct 30 15:05:13.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.1.0.50 peer_port: 5246
    *Oct 30 15:05:13.411: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.1.0.50 peer_port: 5246
    *Oct 30 15:05:13.411: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.0.50
    *Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
    *Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
    *Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.1.0.50
    *Oct 30 15:05:18.411: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.0.50

  • Problem Joining AIR-CAP1602I-C-K9 with WLC 5508

    Hi,
    I am having trouble to get AIR CAP1602I-C-K9 attached to a 5508 WLC running code 7.4.110.0
    Here is what I got from the AP logs:
    ====================================================================================================
    Extracting files...
    ap1g2-k9w8-mx.152-2.JB2/ (directory) 0 (bytes)
    extracting ap1g2-k9w8-mx.152-2.JB2/K5.bin (75790 bytes)!!!!
    *Dec  6 15:09:23.011: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Dec  6 15:09:23.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.10.100 peer_port: 5246
    *Dec  6 15:09:23.535: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.10.100
    *Dec  6 15:09:23.535: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
    *Dec  6 15:09:23.535: %CAPWAP-3-ERRORLOG: CAPWAP!
    extracting ap1g2-k9w8-mx.152-2.JB2/ap1g2-k9w8-mx.152-2.JB2 (9202946 bytes)!!!!!!!!! SM handler: Failed to process message type 10 state 5.
    *Dec  6 15:09:23.535: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Dec  6 15:09:23.535: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 172.16.10.100perform archive download capwap:/ap1g2 tar file
    *Dec  6 15:09:23.583: %CAPWAP-6-AP_IMG_DWNLD: Required image not found on AP. Downloading image from Controller.
    *Dec  6 15:09:23.587: Loading file /ap1g2...
    *Dec  6 15:09:24.007: %LINEPROTO-5-UPDOWN:!!!!!!!!!!! Line protocol on Interface Dot11Radio0, changed state to down
    *Dec  6 15:09:24.063: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up!!!!!!!!!!!
    *Dec  6 15:09:25.139: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up!!!!!!!!!!
    *Dec  6 15:09:26.135: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
    Premature end of tar file
    ERROR: Problem extracting files from archive.
    Download image failed, notify controller!!! From:7.4.1.37 to 7.4.110.0, FailureCode:3
    archive download: takes 63 seconds
    *Dec  6 15:10:26.851: capwap_image_proc: problem extracting tar file
    ====================================================================================
    after that the AP reboots and do same process over and over again,
    Please help..
    Many Thanks,
    Barth

    Here is the info about AP and WLC:
    (Cisco Controller) >show sysinfo
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.4.110.0
    Bootloader Version............................... 1.0.1
    Field Recovery Image Version..................... 6.0.182.0
    Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
    Build Type....................................... DATA + WPS
    System Name...................................... WLC1-AP
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
    Redundancy Mode.................................. Disabled
    IP Address....................................... 172.16.10.100
    Last Reset....................................... Power on reset
    System Up Time................................... 0 days 4 hrs 12 mins 28 secs
    System Timezone Location.........................
    System Stats Realtime Interval................... 5
    System Stats Normal Interval..................... 180
    Configured Country............................... US  - United States
    Operating Environment............................ Commercial (0 to 40 C)
    --More-- or (q)uit
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +44 C
    External Temperature............................. +28 C
    Fan Status....................................... OK
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 1
    Number of Active Clients......................... 0
    Memory Current Usage............................. Unknown
    Memory Average Usage............................. Unknown
    CPU Current Usage................................ Unknown
    CPU Average Usage................................ Unknown
    Burned-in MAC Address............................ F8:72:EA:EF:2E:A0
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Present, Power Off, Fan On
    Maximum number of APs supported.................. 100
    AP4403.a7fd.f040#sh ver
    Cisco IOS Software, C1600 Software (AP1G2-K9W8-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2012 by Cisco Systems, Inc.
    Compiled Tue 11-Dec-12 04:45 by prod_rel_team
    ROM: Bootstrap program is C1600 boot loader
    BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
    AP4403.a7fd.f040 uptime is 4 minutes
    System returned to ROM by power-on
    System image file is "flash:/ap1g2-k9w8-mx.152-2.JB/ap1g2-k9w8-mx.152-2.JB"
    Last reload reason:
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CAP1602I-C-K9    (PowerPC) processor (revision B0) with 98294K/32768K bytes of memory.
    Processor board ID FGL1711ZJNW
    PowerPC CPU at 533Mhz, revision number 0x2151
    Last reset from power-on
    LWAPP image version 7.4.1.37
    1 Gigabit Ethernet interface
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 44:03:A7:FD:F0:40
    Part Number                          : 73-14671-04
    PCA Assembly Number                  : 000-00000-00
    PCA Revision Number                  :
    PCB Serial Number                    : FOC16517DZ1
    Top Assembly Part Number             : 800-38552-01
    Top Assembly Serial Number           : FGL1711ZJNW
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP1602I-C-K9
    Configuration register is 0xF
    AP4403.a7fd.f040#sh inventory
    NAME: "AP1600", DESCR: "Cisco Aironet 1600 Series (IEEE 802.11n) Access Point"
    PID: AIR-CAP1602I-C-K9 , VID: V01, SN: FGL1711ZJNW

  • Time machine backup over wan with bonjour: are transfers encrypted?

    Hello,
    I have setup a dynamic global hostname and am sharing the connected disk over the WAN with Bonjour, and am able to backup files to the disk connected to the airport extreme over the internet when away from home. Very handy. My question is: are these file transfers encrypted? I've been searching around, but have been unable to find a definitive answer.
    From this doc: http://developer.apple.com/mac/library/documentation/Networking/Conceptual/AFP/A FPSecurity/AFPSecurity.html#//apple_ref/doc/uid/TP40000854-CH232-SW1
    "Only Mac OS X Server can be connected to via AFP over SSH - AND you have to enable it at the server end. You cannot connect to a Mac OS X Client with AFP over SSH."
    So, I take it this means the authentication to the disk is encrypted, but the file transfer itself proceeds in plain text?
    Thanks,
    Bob

    You need to know that Time Machine backups to a USB drive on an Airport Extreme are "iffy" and +*not supported by Apple.+*
    See Using Time Machine with an Airport Extreme Air Disk (or use the link in *User Tips* at the top of this forum).
    Time Machine does not do encryption (or compression).

  • True copy over wan with HDS

    hello
    we are replicating two storage systems HDS9980 with "true copy", the replication is over stm1.
    from HDS with uses cisco MDS 9200 to convert FC to GeTH and from there cisco 7600 to convert GeTH to stm1.
    we use a full synchronous replication.
    my question is , what improvements can we implement: such as jumbo frames , FCIP write acceleration or other suggestions?

    From an MDS perspective we can go either FC or FCIP.
    200km is not a problem for FC. We have 250 buffer credits standard per port which allows you to go the 200km @ 2Gbps. If you want to use 4 Gbps you will need the extended buffer credit feature which is part of the enterprise license and allows you to define up to 4095 credits per port (more than enough).
    For FCIP you can use the write acceleration and hardware compression features.
    Portchannelling and VSAN trunking as well as inter-vsan-routing can be used together with QoS mechanisms to optimize the connectivity for both FCIP and FC.
    It all depends on how much data needs to get through and what the latency requirements are and what type of connectivity (IP, dark fiber, DWDM) you can get at what price.
    You should work with HDS and your local Cisco Storage SE to sort out what is best for you.
    Ralf

  • No FTP access over WAN with Airport Extreme 802.11n v7.3.2

    hi there,
    I've read through a few different posts on this topic (both here and in other forums) but I can't seem to find the answers I need.
    I have an AEBS n with version 7.3.2 of Airport Utility. attached to the AEBS is a hard drive. I want to enable file sharing (mostly FTP, but AFP would be fine too) to access the drive through the WAN port.
    here's what I've done:
    - connected a USB drive. This is available through my LAN and is accessible using my OSX account login & password)
    - enabled filesharing and "share disks over ethernet WAN port"
    - enabled NAT and default host on the AEBS
    - configured port mappings for FTP and ARD (I couldn't enable any other file sharing because of a port conflict. Is this because the hard drive connected to the AEBS is already set to use these?)
    I created an account with DynDNS to resolve my ip to a domain name.
    when I ping either my domain or the IP, I get the same results. it sees my isp but the destination host is unreachable.
    port scanning my domain from 20 through 548 shows that 139, 445, and 548 are open. but no 20.
    what am I doing wrong here?
    thanks in advance

    bump

  • BackUp over WAN (with MobileMe)

    Hello,
    I can remotely connect to my TC (when on the road) using my MobileMe account and "Back to my Mac". I can see it on finder, connect to it, read/write to files all is well.
    But I just can't do any backup with Time Machine. It says the backup disk is not available. If I try to manually select a disk, there is only the option "None" in the list, the remote TC disk is not available. Any clue ?
    Thank you.

    Some folks have gotten that to work, but backing-up over the internet is excruciatingly slow, at best.
    This post may help: http://discussions.apple.com/thread.jspa?messageID=11499979#11499979

  • Cisco CAP 3702I not registered with WLC 5508.

    I Have  WLC 5508 in my network. Now i need to add another 2 no of cisco CAP 3702I in to my network. But we got the following errors
    *Mar  1 01:27:06.359: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'WLC'runn
    ing version 7.3.101.0 is rejected.
    *Mar  1 01:27:06.359: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 01:27:06.359: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process m
    essage type 2 state 2.
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 01:27:25.359: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
    LER
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'WLC'runn
    ing version 7.3.101.0 is rejected.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process m
    essage type 2 state 2.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Failed to handle capwap control messag
    e from controller
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap p
    acket from 10.56.200.201
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'WLC'runn
    ing version 7.3.101.0 is rejected.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process m
    essage type 2 state 2.
    *Mar  1 01:27:06.359: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'WLC'runn
    ing version 7.3.101.0 is rejected.
    *Mar  1 01:27:06.359: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 01:27:06.359: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process m
    essage type 2 state 2.
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 01:27:25.359: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
    LER
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'WLC'runn
    ing version 7.3.101.0 is rejected.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process m
    essage type 2 state 2.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Failed to handle capwap control messag
    e from controller
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap p
    acket from 10.56.200.201
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'WLC'runn
    ing version 7.3.101.0 is rejected.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 01:27:25.363: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process m
    essage type 2 state 2.

    Your WLC seems to be running version 7.3 which is not supported with 37xx AP platform.
    You need to run WLC with version 7.6.100.0 onwards to support these new AP's.
    For more details check the Wireless Software Compatibility Matrix.
    -Thanks
    Vinod
    **Encourage Contributors. RATE Them.**

  • Voice over Wireless with Cisco phones 7921 and 7925

    Hello experts,
    I made an wireless audit for a company.
    They have 2 WLCs 5508 in HA mode, with APs 2602 for indoor and 1552. Version of the WLC : 7.6.120.0
    At the end of the day we noticed that the roaming between indoor and outdoor access points is sometimes failing and results to a complete disconnection of the wireless phone (7921 or 7925) from the network. When people go from the indoor to the outdoor area, there is no problem. The problem comes when people are coming from the outdoor to the indoor.
    Also, on the WLC, the power lvl of the outdoor APs are set to 1 ... Is it good or not ?
    My question is, is there any known issue about Voice over wireless with WLC 5508-7.6.120.0 with APs 2602 and 1552 ?
    Maybe it should be better to upgrade to 7.6.130.0 ?
    Thanks in advance,
    Alexis

    Normally yes.
    Is there a way to troubleshoot what's going on with the phones ? Maybe a "show client detail MAC address* on the WLC ?
    Here are some logs when the phones are losing the network :
    *Dot1x_NW_MsgTask_4: Apr 09 12:44:21.320: #DOT1X-3-INVALID_WPA_KEY_MSG_STATE: 1x_eapkey.c:957 Received invalid EAPOL-key M2 msg in START  state - invalid secure bit; KeyLen 40, Key type 1, client 00:24:d7:83:56:dc
    *apfMsConnTask_6: Apr 09 12:28:32.668: #APF-3-VALIDATE_CCKM_REASS_REQ_ELEMENT: apf_utils.c:2506 Could not validate the CCKM Reassociation request element.Received Timestamp deviation > 1sec in CCKM Info Element from mobile. Mobile:4c:00:82:85:6e:e1,  AP:1
    *Dot1x_NW_MsgTask_1: Apr 09 12:26:53.964: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 74:26:ac:63:8c:a9 - got 00 00 00 00 00 00 00 03, expected 00 00 00 00 00 00 00 04
    *Dot1x_NW_MsgTask_1: Apr 09 12:26:53.929: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 74:26:ac:63:8c:a9 - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 04
    *apfMsConnTask_4: Apr 09 12:24:34.959: #APF-3-VALIDATE_CCKM_REASS_REQ_ELEMENT: apf_utils.c:2506 Could not validate the CCKM Reassociation request element.Received Timestamp deviation > 1sec in CCKM Info Element from mobile. Mobile:78:da:6e:f6:5f:89,  AP:5
    *Dot1x_NW_MsgTask_0: Apr 09 12:22:30.217: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 4c:00:82:85:1d:68 - got 00 00 00 00 00 00 00 03, expected 00 00 00 00 00 00 00 04
    *Dot1x_NW_MsgTask_4: Apr 09 12:22:30.206: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 4c:00:82:85:b3:ac - got 00 00 00 00 00 00 00 03, expected 00 00 00 00 00 00 00 04
    *Dot1x_NW_MsgTask_4: Apr 09 12:22:30.186: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 4c:00:82:85:b3:ac - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 04
    *Dot1x_NW_MsgTask_0: Apr 09 12:22:30.167: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 4c:00:82:85:1d:68 - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 04
    *Dot1x_NW_MsgTask_6: Apr 09 12:22:29.672: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 78:da:6e:f6:14:2e - got 00 00 00 00 00 00 00 03, expected 00 00 00 00 00 00 00 04
    *Dot1x_NW_MsgTask_6: Apr 09 12:22:29.638: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 78:da:6e:f6:14:2e - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 04
    *apfMsConnTask_3: Apr 09 12:19:22.098: #APF-3-VALIDATE_CCKM_REASS_REQ_ELEMENT: apf_utils.c:2506 Could not validate the CCKM Reassociation request element.Received Timestamp deviation > 1sec in CCKM Info Element from mobile. Mobile:4c:00:82:85:6e:e1,  AP:5
    *osapiBsnTimer: Apr 09 12:13:36.031: #LOG-3-Q_IND: spam_lrad.c:53542 The system is unable to find WLAN 2 to be deleted

  • Cisco AIR-SAP2602I-N-K9 vs AIR-CAP2602I-E-K9

    What's the difference between "AIR-SAP2602I-N-K9" and " AIR-CAP2602I-E-K9 "?

    Hi there, the difference between the two is the  regulatory domain they work on. The 802.11 specification as regulatory domains defines the different parameters for antenna gain, transmit power, channel selection, and so on. A (A regulatory domain - FCC):North America, South America, Central America, Australia, New Zealand, various parts of Asia E (E regulatory domain - ETSI):Europe, Middle East, Africa, various parts of Asia As you see on this site for example European shops sell the Cisco air-cap2602i-e-k9: http://hardware.nl/cisco/air-cap2602i-e-k9.html N (N regulatory domain - Non FCC):Mexico, Australia Find all regions divided by Cisco here: http://www.cisco.com/c/en/us/products/collateral/wireless/access-points/product_data_sheet0900aecd80537b6a.html

  • Cisco AIR 1142N wireless speed.

    Hello all.
    Just got Cisco AIR 1142N, configured it with two ssids on 2.4 Mhz interface. 5.0 is shutdown. As I know (probably I am wrong) wireless speed with "n" mode devices must be at least 150 Mbps, but I get only half of that- 72 Mbps. Where could be a problem?
    Tested it with notebooks with Broadcom 4313 adapter.
    I have read some people face problem with 54 Mbps speed, but they just have wrong authentication.
    Be glad for any advice!
    and here is a bit of my conf.

    Yeah..I think this is the problem.
    My wi-fi adapter in notebooks is Broadcom 4313b/g/n and this is what I find about it..
    Broadcom 4313GN 802.11b/g/n
    WiFi Adapter
    Integrated support for 802.11 b, g, and n
    1 transmit, 1 receive antenna
    Up to 72 mbps data rate
    Very sad.
    Thanks everyone for the help and detailed responses:)

  • Can't connect N73 to PC over bluetooth

    I can't connect N73 to PC over bluetooth with new Nokia PC Suite v6.84.10.4, I get this message "Cannot use the connection type. Check that all the needed hardware,software and drivers are available". This happened after I instaled new version of PC Suite and the patch to v6.84 didn't help.

    I think the problem is in bluesoleil software It looks like PC Suit does not work with latest IVT Bluesoleil version 3.2.2.8. I tried with and witout patch and I even installed older version of PC Suite that worked before with older version of bluesoleil....

  • SCVMM over WAN

    Is it possible to use SCVMM for another sites over wan with ping delay with about 60 ms?
    Does the SCVMM need a lot of bandwith?
    Thanks

    Hi Possible. I have deployed a VMM in HQ to manage 3 sites (using WAN) before.
    In 3 sites, setup VMM Library
    http://social.technet.microsoft.com/wiki/contents/articles/vmm-library-server-best-practices.aspx . Just a file share to store ISO, VHD base,
    etc to avoid any large file to transfer through WAN.
    You can check on my blog about the port that you need to open .
    http://www.ms4u.info/2010/06/port-to-open-when-adding-host-in.html
    laiys

  • Cisco Unity with Microsoft Exchange over WAN Question

    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-priority:99;
    mso-style-qformat:yes;
    mso-style-parent:"";
    mso-padding-alt:0in 5.4pt 0in 5.4pt;
    mso-para-margin:0in;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:11.0pt;
    font-family:"Calibri","sans-serif";
    mso-ascii-font-family:Calibri;
    mso-ascii-theme-font:minor-latin;
    mso-fareast-font-family:"Times New Roman";
    mso-fareast-theme-font:minor-fareast;
    mso-hansi-font-family:Calibri;
    mso-hansi-theme-font:minor-latin;
    mso-bidi-font-family:"Times New Roman";
    mso-bidi-theme-font:minor-bidi;}
    A customer has several offices. Each office has a separate Exchange Server. The partner was considering a single Unity deployment connected to all of the exchange servers over the WAN, but has decided against that because the latency of the WAN is too high to do this. They are looking for a best practice way of deploying Unity for these multiple Exchange servers at multiple sites. This might mean a separate Unity server for each exchange server at each site .
                    However, we’re wondering if there is a better way to do this. With multiple unity servers we’ll likely have different prefixes for each unity server at each location . This is something that the customer would like to avoid. We’re wondering if there any best practices for a deployment like this that we can offer as options for the customer.
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-priority:99;
    mso-style-qformat:yes;
    mso-style-parent:"";
    mso-padding-alt:0in 5.4pt 0in 5.4pt;
    mso-para-margin:0in;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:11.0pt;
    font-family:"Calibri","sans-serif";
    mso-ascii-font-family:Calibri;
    mso-ascii-theme-font:minor-latin;
    mso-fareast-font-family:"Times New Roman";
    mso-fareast-theme-font:minor-fareast;
    mso-hansi-font-family:Calibri;
    mso-hansi-theme-font:minor-latin;
    mso-bidi-font-family:"Times New Roman";
    mso-bidi-theme-font:minor-bidi;}
    I have found some related information but really customer is altogether looking for an option away from Exchange networking over WAN.
    I found:
    “Multi-Site WAN with Distributed Messaging”
    http://www.cisco.com/en/US/docs/voice_ip_comm/unity/5x/design/guide/5xcudg040.html#wp1077309
    “Networking Options Requirements for Cisco Unity”
    http://www.cisco.com/en/US/products/sw/voicesw/ps2237/prod_installation_guides_list.html
    Design Guide for Cisco Unity also talk as much is there in the first URL.
    Please Help!

    This may be counter to your customer's desire or requirements but I must ask the question.  Has the customer considered Unity Connection vs. Unity?  Granted, Unity Connection provides integrated messaging whereas Unity is the unified messaging application; however, CUC has become Cisco's flagship messaging product over the last couple of years and I only see this expanding to be honest.  So, for new installs - I push hard on Unity Connection.  Sometimes, it's a sell but sometimes the customer has a hard requirement for UM and thus you have to go with UM.  In your scenario, your customer could potentially save a LARGE amount of money as CUC is not dependent upon Exchange at all; however, you still have the option to tie into Exchange 2003/2007 as an external service where users can access messages in a 3rd-party message store and also access calendar data and so forth.  The platform is very feature rich.  Many of my current Unity customers are migrating off of the platform to the more "agnostic" CUC platform to avoid issues caused by such dependence on AD/Exchange.  In addition, as Microsoft continues to develop and push it's own UM solution - integration for Unity is being forced to change (ex: changes to MAPI in 2010 caused problems for Cisco and required them to rework a bit of the underpinning integration points between Unity and Exchange).  With CUC, you also have the flexibility to implment a dial plan within voicemail system itself...not to mention it is extremely scalable.
    Hailey
    Please rate helpful posts!

Maybe you are looking for

  • How do I run a Midi Light show from within Logic Pro?

    Hello, I'm trying to figure out how to run a midi light show along side or within logic pro. I currently run .wav synth files through logic into an Onyx Satellite into the PA system, I want to run a lights show that fits perfectly with each part of t

  • I generate file (PDF, HTML, etc) the report is empty but I run in paper

    Hi I use oracle Report10g When I generate file (PDF, HTML, etc) the report is empty but I run in paper design show data, the report in the paper design show many pages, when generate file show only the information of the margin in the main seccion an

  • Crystal Reports Server 2008 (Linux) - Crystal Reports/MySQL/ODBC Issue

    Hello, I have successfully installed CRS '08 on a Red Hat Enterprise Linux 4 server.  All services run fine. In the CMC, I have uploaded a Crystal Report that connect to a remote MySQL server.  I have installed the My SQL ODBC 3.51.11 and .12 Drivers

  • Mass printing of resume/Attachment in eRecruitment

    Hi, Is there a way to achieve mass printing/download of the attachments from the profiles of multiple candidates in Erecruitment ? Thanks, Phani Gorthi.

  • JAXM API and JAXMServlet

    Hi, I'm learning to use Web Services. I have discovered Axis and this project looks great. But someone told me that I can extend JAXMServlet from JAXM API to manage my web service on server side. My web service will have only strings on input and out