Connecting FAX to PSTN line using FXS and FXO ports
I have 2 cisco 1760 routers with FXS and FXO card installed in each. I have to transport 2 PSTN lines from Head Office to remote loaction using FXS and FXO cards and these lines will be used for voice calls and FAX( one line each for FAX and voice). I have configured the router for voice lines and it is working fine. Now I am using the same config for running fax machine but it is not working. Can anyone help me out how to configure FAX in this scenario also if anyone can share any sample config. I am attaching my config for both routers. Right now both routers are connected with a cross-over cable for lab test but we will connect them later using satellite connection.
HO Router (FXO card)
Current configuration : 1718 bytes
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
enable password cisco
no aaa new-model
resource policy
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
voice-card 2
voice-card 3
ip subnet-zero
ip cef
no ip dhcp use vrf connected
no ip domain lookup
no ftp-server write-enable
voice class codec 10
interface FastEthernet0/0
ip address 10.10.10.1 255.255.255.248
speed auto
h323-gateway voip bind srcaddr 10.10.10.1
ip classless
no ip http server
control-plane
voice-port 2/0
output attenuation 0
echo-cancel coverage 32
no vad
no comfort-noise
timeouts interdigit 3
timeouts call-disconnect 3
connection plar opx 2001
description Remote PSTN#:35296913
music-threshold -70
voice-port 2/1
output attenuation 0
echo-cancel coverage 32
no vad
no comfort-noise
timeouts interdigit 3
timeouts call-disconnect 3
connection plar opx 2002
description Remote PSTN#:35296914
music-threshold -70
voice-port 3/0
voice-port 3/1
dial-peer voice 2000 voip
destination-pattern 200.
no modem passthrough
voice-class codec 10
session target ipv4:10.10.10.2
incoming called-number .
dtmf-relay cisco-rtp h245-signal h245-alphanumeric
fax-relay ecm disable
fax rate 7200
fax nsf 000000
no vad
dial-peer voice 1321 pots
description line 1
huntstop
destination-pattern 1321
port 2/0
dial-peer voice 1322 pots
description line 2
huntstop
destination-pattern 1322
port 2/1
line con 0
password cisco
line aux 0
line vty 0 4
password cisco
login
end
Remote Router (FXS Card):
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
enable password cisco
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
voice-card 2
voice-card 3
no aaa new-model
ip subnet-zero
ip cef
no ip domain lookup
no ftp-server write-enable
voice class codec 10
interface FastEthernet0/0
ip address 10.10.10.2 255.255.255.248
speed auto
h323-gateway voip bind srcaddr 10.10.10.2
interface Ethernet1/0
no ip address
shutdown
half-duplex
ip classless
no ip http server
control-plane
voice-port 2/0
description PSTN#:
voice-port 2/1
description PSTN#:
voice-port 3/0
voice-port 3/1
dial-peer voice 2001 pots
description Remote
huntstop
destination-pattern 2001
port 2/0
dial-peer voice 2002 pots
description Remote
huntstop
destination-pattern 2002
port 2/1
dial-peer voice 1320 voip
destination-pattern 132.
no modem passthrough
voice-class codec 10
session target ipv4:10.10.10.1
incoming called-number .
dtmf-relay cisco-rtp h245-signal h245-alphanumeric
fax-relay ecm disable
fax rate 7200
fax nsf 000000
no vad
line con 0
password cisco
line aux 0
line vty 0 4
password cisco
login
end
In your voice class codec 10 there aren't any codecs declared.
Add G.711 codec in this way:
voice class codec 10
codec preference 1 g711alaw
If the fax communication fails again try to disable T.38 and try fax passthrough mode:
no fax rate
modem passthrough nse codec g711alaw
fax protocol pass-through g711alaw
Regards.
Similar Messages
-
Hi, I'm using a Mac Pro here. I am trying to connect it with my NAS hard drive. But i could not connect to it because i have an ethernet which connects to the intranet in my company and Air Port for the internet and it could not detect the the ip address after i input the correct address on "Connect to Server" window. Please help! Urgent! Thanks
I did not say it is not possible.
I said if your company networks are monopolizing both ports, you should talk to them about what options are available.
Maybe you can get the company Intranet over wireless if you change some configuration items such as Subnet Mask.
Maybe you can get on the Internet over Ethernet.
You really need to ask them, and do not let them blow you off because you have a Mac. If they balk, ask them how it would be done on a PC (becasue it will be the same on a Mac). -
I have a Samsung VGA Monitor connected to my MacBook Pro using the Mini Display Port to VGA Adapter. How do I configure the computer so that it doesn't sleep when I close the lid of the computer.
Hi alangium,
Welcome to the Support Communities!
Resetting your computer's PRAM should restore your Macbook Pro's screen appearance.
OS X Mavericks: Reset your computer’s PRAM
http://support.apple.com/kb/ph14222
This article may provide some information about your Mini DisplayPort to AVI adapter. Have you tried to connect a different VGA monitor to your Macbook to see if you get the same results?
Apple Mini DisplayPort adapters: Frequently asked questions (FAQ)
http://support.apple.com/kb/HT3382
18. What is the maximum resolution available for use with the Apple Mini DisplayPort to VGA adapter?
The resolution available with the Apple Mini DisplayPort to VGA Adapter is 1920 x 1200. VGA displays that use higher refresh rates (such as 85 Hz) at resolutions of 1600 x 1200 or greater may not generate video properly until you lower the refresh rate.
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/HT1573#5
How can I detect displays?
If the detect displays option is not available, hold down the Option key while you are in the Display pane.
How do I select additional resolutions on my display?
You can use the Display pane of System Preferences to specify how your display works. Not all options appear for all display models. By default the best resolution for your display will already be selected in System Preferences.
To select a different resolution, use the Scaled option. Some additional resolutions may be available when you hold the Option button.
I hope this information helps ....
- Judy -
Differences between FXS and FXO ...?
Could someone let me know the difference between FXS and FXO with respect to a router, a PBX, a CO Switch, an analog phone, an ISDN phone?
Here are a couple of URLs explaining the same:
http://www.qtelnet.com/downloads/FXO-vs-FXS-v3.pdf
http://www.patton.com/technotes/fxs_fxo.pdf -
HT204266 I am facing problem to connect to the App Store using 3G and wi-fi
Hello
I am facing problem to connect to App Store from my iphone using 3G and wi-fi. It allows me to update the installed apps.The iTune Store is not available in certain countries
http://support.apple.com/kb/TS3599 -
Dear Friends,
I am using OCI and instant_client (11.2.0.3.0) in my C++ program (on Windows 7) to connect remotely to 11G database.
While doing a connection using server name as well as servername:port/service_name as connection strings, I am getting error of ORA-12504 TNS:listener was not given the SERVICE_NAME in CONNECT_DATA.
According to instant client FAQ & white paper at http://www.oracle.com/technetwork/database/features/instant-client/index.html, no tnsnames.ora is required for instant client. Then why could I be getting this error?
I ensured that only the instant client directory is in Path environment variable. There was a ODBC driver installed on this same host. Could that be modifying the behavior of instant client?
Kindly guide.
Many thanks in advance for your help and time.
Best Regards,
- ganesh>>what is the exact connect string you are using?
For connection, I am using the plain hostname on which the DB server is running.
>>are you calling OCIServerAttach before OCISessionBegin?
I am not using OCISessionBegin. For connecting to DB server, I am using the following sequence of OCI calls (in this same order):
1) g_OCIEnvNlsCreate
2) g_OCIHandleAlloc //-- error handle: OCI_HTYPE_ERROR
3) g_OCIHandleAlloc // --- sevice context: OCI_HTYPE_SVCCTX
4) Setting driver name and application name for the session:
OCISession* usersession = 0;
ret = g_OCIAttrGet(m_pSvcCtx, OCI_HTYPE_SVCCTX, &usersession, NULL,
OCI_ATTR_SESSION, m_pErrHdl);
if (ret == OCI_SUCCESS)
ret = g_OCIAttrSet(usersession, OCI_HTYPE_SESSION, (void*)"OCI_DRV", 2,OCI_ATTR_DRIVER_NAME, m_pErrHdl);
ret = g_OCIAttrSet(usersession, OCI_HTYPE_SESSION, (void*)"ClientApplication", <ub4>(strlen("DataReconScanning")), OCI_ATTR_CLIENT_IDENTIFIER, m_pErrHdl);
5) g_OCILogon() using the user, password and host name, as below:
g_OCILogon(m_pDbCon, m_pErrHdl, &m_pSvcCtx,
(text*)user.c_str(), static_cast<ub4>(user.length()),
(text*)pass.c_str(), static_cast<ub4>(pass.length()),
(text*)host.c_str(), static_cast<ub4>(host.length()));
Thanks. -
I got a new ipod touch and in the beginning instead of connecting to itunes on the computer i used wifi and now on the the computer it wont let me log on when itunes pops up what do i do?
What do you mean by: " computer it wont let me log on when itunes pops up what do i do?"?
What happens? -
Long connection times to Leopard server using ssh and screen sharing
I'm experiencing long connection times when using ssh (30 seconds, or so, before password prompt appears), and screen sharing (upwards of 5 minutes before display opens). Both the server and the macbook pro I'm connecting with are on the same LAN, with the sever connected by wire directly to an Airport Extreme, and the MBP connecting via wireless.
Anybody have any thoughts as to what's causing the long delays in connecting?A ping goes rather quickly, and the TNSNAMES.ORA file already contains the IP address. I have other software that connects to the Oracle server just fine without a long delay. I am not sure if this other software uses ODBC, it is a package software. I was begining to think I might have miscoded the connection in the VB program?
Tim -
FXS and FXO configuration and design help
hi all...
i am new to voip configuration... and i have to configure the voip for our branch office... we have 2610 with the 2FXS and 2FXO prot... now i have one pulblic IP address which is used by my local lan user...and we have configured NAT/PAT on our VPN concerntrator... now we are looking to establish the VOIP phone (analogphone with the help of FXO and FXS) we have ASTRIK server at our main office and i want to register my local office analog phone with server at our main office... now what kind of configuration we need on our 2610 in order to configure voip...
connectivity:
ADSL connection form ISP---VPN 3005---D-Link nonmanagable swithch---LAN
at present we have above connectivity and now i want to add my 2610 router with analogphone connected to it... how can i connect and how can i configure it...?
regards
Devangyou need to configure pots and voip dialPeers for the incoming/outgoing legs of the calls.
pots dialPeers will be used for the FXO/FXS ports. voip dialPeers will be used for connection to ASTERISK voip pbx.
you need voice port configuration for your FXS to connect to your analogPhone.
you need voice port configuration for your FXO to connect to analog pstn. (if you have any)
see these links for more info:
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a008010ae1c.shtml
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a0080147524.shtml
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a008010fed1.shtml
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_configuration_example09186a00801bc341.shtml
http://www.cisco.com/en/US/tech/tk652/tk653/tech_configuration_examples_list.html
there are plenty of examples throughout these for reference. -
Issue with SPA525g registation and FXO port call calls are not disconnecting properly
Hi,
I have a UC540 and updated it to the latest IOS version with the latest firmware to my phones and i am having registration problems with SPA525g IP Phones. I updated the firmware of the phones as well and create manual tftp bindings with but still it is not registering. I run a couple of debugs (debug tftp events and debug ephone registration) I can see from the logs and in the phone that it is taking the proper VLAN and being discovered via CDP and being pointed to the TFTP server and still wont register. I can see that it is also taking its own .cnf file properly then the output sccp token regected invalid devices error is shown I have a SPA502G and it is working fine. Also there is a previous issue that all the voice port are shown as engage or offhook even the calls are disconnected thus make the main PSTN number busy am based in UAE and our service provider is etisalat I have check with them about the proper disconnection values but still it the same. That's why I have arrived in the conclusion to just update everything including the IOS and the phones firmware. I have put my config in this post, I am also trying to take the CCNA Voice exam on the 2nd week of april and I think that if i don't know how fix this issue for our customer then I would probably fail that exam. any suggestion and help is greatly appreciated cisco experts.
! Last configuration change at 13:36:42 ZP4 Thu Sep 13 2012 by Nick
! NVRAM config last updated at 13:45:41 ZP4 Thu Sep 13 2012 by Nick
version 15.1
parser config cache interface
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service internal
service compress-config
service sequence-numbers
hostname UC540
boot-start-marker
boot system flash:uc500-advipservicesk9-mz.151-2.T4
boot-end-marker
logging buffered 64000
enable secret 5 $1$3CIf$.rXyHeJQrwd97X/f2dS0M1
no aaa new-model
clock timezone ZP4 4 0
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-3558175224
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3558175224
revocation-check none
crypto pki certificate chain TP-self-signed-3558175224
certificate self-signed 01 nvram:IOS-Self-Sig#3.cer
dot11 syslog
dot11 ssid cisco-data
vlan 1
authentication open
dot11 ssid cisco-voice
vlan 100
authentication open
ip source-route
ip cef
ip dhcp relay information trust-all
ip dhcp excluded-address 10.1.3.1 10.1.3.10
ip dhcp pool phone
network 10.1.3.0 255.255.255.0
default-router 10.1.3.1
option 150 ip 10.1.3.1
ip name-server 213.42.20.20
ip name-server 195.229.241.222
ip inspect WAAS flush-timeout 10
ip inspect name SDM_LOW cuseeme
ip inspect name SDM_LOW dns
ip inspect name SDM_LOW ftp
ip inspect name SDM_LOW h323
ip inspect name SDM_LOW https
ip inspect name SDM_LOW icmp
ip inspect name SDM_LOW imap
ip inspect name SDM_LOW pop3
ip inspect name SDM_LOW netshow
ip inspect name SDM_LOW rcmd
ip inspect name SDM_LOW realaudio
ip inspect name SDM_LOW rtsp
ip inspect name SDM_LOW esmtp
ip inspect name SDM_LOW sqlnet
ip inspect name SDM_LOW streamworks
ip inspect name SDM_LOW tftp
ip inspect name SDM_LOW tcp router-traffic
ip inspect name SDM_LOW udp router-traffic
ip inspect name SDM_LOW vdolive
no ipv6 cef
multilink bundle-name authenticated
stcapp ccm-group 1
stcapp
stcapp supplementary-services
port 0/0/0
fallback-dn 301
port 0/0/1
fallback-dn 302
port 0/0/2
fallback-dn 303
port 0/0/3
fallback-dn 304
trunk group ALL_FXO
max-retry 5
voice-class cause-code 1
hunt-scheme longest-idle
translation-profile outgoing PROFILE_ALL_FXO
trunk group ALL_FX0
voice call send-alert
voice rtp send-recv
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
sip
no update-callerid
voice class codec 1
codec preference 1 g711alaw
codec preference 2 g711ulaw
voice class dualtone-detect-params 1
freq-max-deviation 50
freq-max-power 0
freq-min-power 13
freq-power-twist 4
cadence-variation 6
voice class custom-cptone UAE-CUSTOM
dualtone disconnect
frequency 406
cadence 398 344 237 527 400
voice class custom-cptone CCAjointone
dualtone conference
frequency 600 900
cadence 300 150 300 100 300 50
voice class custom-cptone CCAleavetone
dualtone conference
frequency 400 800
cadence 400 50 200 50 200 50
voice class cause-code 1
no-circuit
voice register global
voice hunt-group 1 parallel
list 301,302,303
timeout 24
pilot 511
voice translation-rule 4
rule 15 // //
voice translation-rule 1000
rule 1 /.*/ //
voice translation-rule 1111
voice translation-rule 1112
rule 1 /^9/ //
rule 3 /^0/ //
voice translation-rule 2222
voice translation-rule 3265
rule 1 /\(^..........$\)/ /9\1/
rule 2 /\(^.........$\)/ /9\1/
rule 15 /\(^ABCD$\)/ /ABCD\1/
voice translation-profile CALLER_ID_TRANSLATION_PROFILE
translate calling 1111
voice translation-profile CallBlocking
translate called 2222
voice translation-profile INCOMING_CallerID_PROFILE
translate calling 3265
voice translation-profile OUTGOING_TRANSLATION_PROFILE
translate called 1112
voice translation-profile PROFILE_ALL_FXO
translate calling 4
voice translation-profile nondialable
translate called 1000
voice-card 0
dspfarm
dsp services dspfarm
license udi pid UC540W-FXO-K9 sn FHK143074G6
archive
log config
logging enable
logging size 600
hidekeys
username cisco privilege 15 secret 5 $1$vjNa$OFKLhupqR8al6x2b8Xmcj/
username adminac privilege 15 secret 5 $1$NDC.$PtD0y4YGIj5SqI1gghxWE1
username Nick privilege 15 secret 5 $1$iAmL$tsg7Jf2TEND1NN.h8z2dy/
ip tftp source-interface Loopback0
bridge irb
interface Loopback0
description $FW_INSIDE$
ip address 10.1.10.2 255.255.255.252
ip access-group 101 in
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/0
description $FW_OUTSIDE$
ip address 192.168.101.2 255.255.255.252
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
interface Integrated-Service-Engine0/0
description cue is initialized with default IMAP group
ip unnumbered Loopback0
ip nat inside
ip virtual-reassembly in
service-module ip address 10.1.10.1 255.255.255.252
service-module ip default-gateway 10.1.10.2
interface FastEthernet0/1/0
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/1
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/2
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/3
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/4
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/5
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/6
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/7
switchport access vlan 20
spanning-tree portfast
interface FastEthernet0/1/8
switchport access vlan 100
macro description cisco-switch
interface Dot11Radio0/5/0
no ip address
shutdown
ssid cisco-data
ssid cisco-voice
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
interface Dot11Radio0/5/0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0/5/0.100
encapsulation dot1Q 100
bridge-group 100
bridge-group 100 subscriber-loop-control
bridge-group 100 spanning-disabled
bridge-group 100 block-unknown-source
no bridge-group 100 source-learning
no bridge-group 100 unicast-flooding
interface Vlan1
no ip address
bridge-group 1
bridge-group 1 spanning-disabled
interface Vlan20
ip address 10.10.10.1 255.255.255.0
interface Vlan100
no ip address
bridge-group 100
bridge-group 100 spanning-disabled
interface BVI1
description $FW_INSIDE$
no ip address
ip nat inside
ip virtual-reassembly in
shutdown
interface BVI100
description $FW_INSIDE$
ip address 10.1.3.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http path flash:/gui
ip dns server
ip nat inside source list 1 interface FastEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 192.168.101.1
ip route 10.1.10.1 255.255.255.255 Integrated-Service-Engine0/0
logging esm config
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 192.168.10.0 0.0.0.255
access-list 1 permit 10.1.3.0 0.0.0.255
access-list 1 permit 10.1.10.0 0.0.0.3
access-list 100 remark auto generated by SDM firewall configuration
access-list 100 remark SDM_ACL Category=1
access-list 100 deny ip 192.168.10.0 0.0.0.255 any
access-list 100 deny ip host 255.255.255.255 any
access-list 100 deny ip 127.0.0.0 0.255.255.255 any
access-list 100 permit ip any any
access-list 101 remark auto generated by SDM firewall configuration##NO_ACES_8##
access-list 101 remark SDM_ACL Category=1
access-list 101 permit tcp 10.1.3.0 0.0.0.255 eq 2000 any
access-list 101 permit udp 10.1.3.0 0.0.0.255 eq 2000 any
access-list 101 deny ip 10.1.3.0 0.0.0.255 any
access-list 101 deny ip 192.168.10.0 0.0.0.255 any
access-list 101 deny ip 192.168.101.0 0.0.0.3 any
access-list 101 deny ip host 255.255.255.255 any
access-list 101 deny ip 127.0.0.0 0.255.255.255 any
access-list 101 permit ip any any
access-list 102 remark auto generated by SDM firewall configuration##NO_ACES_6##
access-list 102 remark SDM_ACL Category=1
access-list 102 deny ip 10.1.10.0 0.0.0.3 any
access-list 102 deny ip 10.1.3.0 0.0.0.255 any
access-list 102 deny ip 192.168.101.0 0.0.0.3 any
access-list 102 deny ip host 255.255.255.255 any
access-list 102 deny ip 127.0.0.0 0.255.255.255 any
access-list 102 permit ip any any
access-list 102 permit ip 192.168.101.0 0.0.0.3 any
access-list 103 remark auto generated by SDM firewall configuration##NO_ACES_8##
access-list 103 remark SDM_ACL Category=1
access-list 103 permit tcp 10.1.10.0 0.0.0.3 any eq 2000
access-list 103 permit udp 10.1.10.0 0.0.0.3 any eq 2000
access-list 103 deny ip 10.1.10.0 0.0.0.3 any
access-list 103 deny ip 192.168.10.0 0.0.0.255 any
access-list 103 deny ip 192.168.101.0 0.0.0.3 any
access-list 103 deny ip host 255.255.255.255 any
access-list 103 deny ip 127.0.0.0 0.255.255.255 any
access-list 103 permit ip any any
access-list 105 permit ip any any
snmp-server community public RO
tftp-server flash:/phones/521_524/cp524g-8-1-17.bin alias cp524g-8-1-17.bin
tftp-server flash:/phones/5x5/spa5x5-7-1-3c.bin alias spa5x5-7-1-3c.bin
tftp-server flash:/phones/525/spa525g-7-4-8.bin alias spa525g-7-4-8.bin
control-plane
bridge 1 route ip
bridge 100 route ip
voice-port 0/0/0
cptone GB
station-id name Cordless
station-id number 329
caller-id enable
voice-port 0/0/1
cptone AE
caller-id enable
voice-port 0/0/2
cptone AE
caller-id enable
voice-port 0/0/3
cptone AE
caller-id enable
voice-port 0/1/0
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4FXO-0/1/0-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/1/1
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4 FXO-0/1/1-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/1/2
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
supervisory dualtone-detect-params 1
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4 FXO-0/1/2-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/1/3
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4 FXO-0/1/3-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/4/0
auto-cut-through
signal immediate
input gain auto-control -15
description Music On Hold Port
sccp local Loopback0
sccp ccm 10.1.3.1 identifier 1 version 4.0
sccp
sccp ccm group 1
associate ccm 1 priority 1
associate profile 1 register confprof1
dspfarm profile 1 conference
description DO NOT MODIFY, active CCA conference profile - CCA2.0 codec729
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
associate application SCCP
dial-peer cor custom
name internal
name local
name local-plus
name international
name national
name national-plus
name emergency
name toll-free
dial-peer cor list call-internal
member internal
dial-peer cor list call-local
member local
dial-peer cor list call-local-plus
member local-plus
dial-peer cor list call-national
member national
dial-peer cor list call-national-plus
member national-plus
dial-peer cor list call-international
member international
dial-peer cor list call-emergency
member emergency
dial-peer cor list call-toll-free
member toll-free
dial-peer cor list user-internal
member internal
member emergency
dial-peer cor list user-local
member internal
member local
member emergency
member toll-free
dial-peer cor list user-local-plus
member internal
member local
member local-plus
member emergency
member toll-free
dial-peer cor list user-national
member internal
member local
member local-plus
member national
member emergency
member toll-free
dial-peer cor list user-national-plus
member internal
member local
member local-plus
member national
member national-plus
member emergency
member toll-free
dial-peer cor list user-international
member internal
member local
member local-plus
member international
member national
member national-plus
member emergency
member toll-free
dial-peer voice 1 pots
port 0/0/0
no sip-register
dial-peer voice 2 pots
port 0/0/1
no sip-register
dial-peer voice 3 pots
port 0/0/2
no sip-register
dial-peer voice 4 pots
port 0/0/3
no sip-register
dial-peer voice 5 pots
description ** MOH Port **
destination-pattern ABC
port 0/4/0
no sip-register
dial-peer voice 50 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/0
dial-peer voice 51 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/1
dial-peer voice 52 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/2
dial-peer voice 53 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/3
dial-peer voice 54 pots
description ** FXO pots dial-peer **
destination-pattern A0
port 0/1/0
no sip-register
dial-peer voice 55 pots
description ** FXO pots dial-peer **
destination-pattern A1
port 0/1/1
no sip-register
dial-peer voice 56 pots
description ** FXO pots dial-peer **
destination-pattern A2
port 0/1/2
no sip-register
dial-peer voice 2000 voip
description ** cue voicemail pilot number **
destination-pattern 388
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 6 pots
description "catch all dial peer for BRI/PRI"
translation-profile incoming nondialable
incoming called-number .%
direct-inward-dial
dial-peer voice 57 pots
description ** FXO pots dial-peer **
destination-pattern A3
port 0/1/3
no sip-register
dial-peer voice 69 pots
destination-pattern 329
port 0/0/0
dial-peer voice 300 pots
trunkgroup ALL_FX0
description Local Numbers
destination-pattern 9T
forward-digits 9
dial-peer voice 301 voip
destination-pattern 2..
session target ipv4:192.168.201.2
dial-peer voice 303 pots
trunkgroup ALL_FXO
trunkgroup ALL_FX0
description **InternationalCall**
destination-pattern 88T
dial-peer voice 304 pots
trunkgroup ALL_FX0
description *EM1*
destination-pattern 9[1-9]T
forward-digits 3
dial-peer voice 302 pots
trunkgroup ALL_FX0
description **Mobiles**
destination-pattern 9.[0-9].[0-9]......
dial-peer voice 305 pots
trunkgroup ALL_FX0
description **800-**
destination-pattern 9[0-9][0-9][0-9]T
no dial-peer outbound status-check pots
telephony-service
sdspfarm conference mute-on 111 mute-off 222
sdspfarm units 5
sdspfarm tag 1 confprof1
conference hardware
video
fxo hook-flash
max-ephones 40
max-dn 300
ip source-address 10.1.3.1 port 2000
max-redirect 20
auto assign 1 to 1 type bri
calling-number initiator
service phone videoCapability 1
service phone webAccess 0
service dnis overlay
service dnis dir-lookup
timeouts interdigit 5
system message American Center
url services http://10.1.10.1/voiceview/common/login.do
url authentication http://10.1.10.2/CCMCIP/authenticate.asp
load 521G-524G cp524g-8-1-17
load 525G spa525g-7-4-8
load 501G spa5x5-7-1-3c
load 502G spa5x5-7-1-3c
load 504G spa5x5-7-1-3c
load 508G spa5x5-7-1-3c
load 509G spa5x5-7-1-3c
time-zone 35
date-format dd-mm-yy
voicemail 388
max-conferences 8 gain -6
call-forward pattern .T
call-forward system redirecting-expanded
hunt-group logout HLog
moh MOH2.wav
multicast moh 239.10.16.16 port 2000
web admin system name cisco secret 5 $1$iDgA$MKNi2RWfsO0KjuC82kgLJ1
dn-webedit
time-webedit
transfer-system full-consult dss
transfer-pattern 9.T
transfer-pattern .T
secondary-dialtone 9
fac standard
create cnf-files version-stamp 7960 Aug 29 2012 12:00:04
line con 0
privilege level 15
logging synchronous
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
exec-timeout 0 0
logging synchronous
login local
transport input all
line vty 5 100
login local
transport input all
ntp master
end
Some of the output are not shown becaus it is to long I have attach the whole config for reference and any advice on how could I optimize and resolve my issues is greatly appreciated. ThanksNicolo - First off this stuff gets crazy sometimes. No worries about the exam. Sometimes when FXO ports go crazy it is due to battery reversal. If you go to the FXO port settings try turning battery reversal on and or off... depending on its current setting. See if that helps.
As for the 525s not registering.. These are inside the network correct? Are you connecting one directly to the UC500 with a Cat5E or Cat6 patch cable and the same thing happens? Does the MAC address on the phone match a MAC address under the EPHONE settings?
If you telnet into the UC500 can you execute a "dir" command at the CLI prompt and "CD" (change directory) into the phones folder and then the spa525g folder? Do files exist in there?
Also I only see an IP address under BVI100? This is the voice side of things what happened to the IP address under BVI1 (Data VLAN). Can you give us some information about the internal network? Cna you PING this phone system from the network? What IP address does it have? -
Line polarity important for FXO ports
I spent several hours trying to get the FXO ports working on my UC320W without success until, in a moment of desperation, I reversed the polarity on the phone line I was using for testing and suddenly everything's working nicely. I've gotten spoiled with other equipment that automatically adjusts to reversed polarity - apparently that's not true for the UC320 or the 8800 units.
Just thought maybe I'd save someone else some aggravation, as I saw no mention of this as a troubleshooting step in the various materials available.Hi Greg,
Thank you for your comments. Couple of additional questions.
Are you located in North America? What type of issues were you having when the polarity was reversed? i.e Call ID or FXO ports not answering, not able to make outbound call... etc..Your feedback is appreciated. I'm checking with our hardware engineers on the issue you raised. I'm also confirming that FCC Part 68 complaince tests for fxo reverse polarity conditions. If your available I'd like to reach out to you after I receive feedback from our hardware team.
Regards,
Randy -
Connect to SAP R/3 using JCA and SLD
I have read a number of articles and code samples regarding back-end connections, but none of them provided the answer which is suitable for my situation.
I want to build a portal application which calls a simple BAPI in a SAP R/3 system.
The only requirements are that the application has to be set up according to the MVC pattern and the model will be exposed as a webservice.
I am using web dynpro to create the views and tie the view, the controller and the model together. The model should connect to a SAP R/3 system accessing it via single sign on.
I want the connection properties to be easily ajustable to make the application portable to another landscape, therefore I chose JCA to set up the connection.
FYI: The SAP back-end systems are defined in the portal system landscape and also in the system landscape directory on the XI server.
Does anyone know a good code sample/tutorial/how-to for setting up a flexible, easy manageable connection to a SAP back-end system?thanks, I can get the data from SAP R/3 to crystal report.
but still dont know how to do the second question mentioned in previous message:
once the table I want to get the data from is a cluster, and have found the mapping data dictionary of this data cluster, which displayed in crystal report connection as well, however, the data is not what I wanted. -
Connect to Existing Wireless Network Using AE and 2WIRE Home Portal
I would like to use my airport express to connect to an existing wireless network set up in my place, I got a pc wireless network connected with a 2Wire Homeportal 1000HW.
I've tried with the Assitant in both options, just joining the network to play music or joining the network to extend the range and nothing works, always the AE disappears.
Can I do that with my home portal or I need a different one?
If I need a new one what should I buy, my provider is SBC (DSL)
HP Pavilion zv6000 Windows XPI am on a Mac and can do this with my 2Wire 1000SW. Not sure what the difference is, but I imagine it's just speed (mine is 802.11b). The reference to another posting on the 2Wire says that you must disable WEP. I have all my security still in place. When I run the setup utility and ask it to join my existing network (2Wire Network), it asks for my WEP and runs from there.
Were you able to get this to work? -
Can JConsole connect to remote JMX agent using JMXMP and TLS?
I have a JMX Enabled App that needs to be accessed with JConsole using TLS enabled JMXMP Connector.
The same server can be accessed with a custom JMX client but JConsole is causing be trouble.
I get error something like: "Client does not support profiles but the server requires it..."
thanks
Srini<p>Hi John,</p>
<p>Unfortunately there isn't a simple solution for this because you cannot pass to JConsole the environment map to be used to configure your JMXMP connector client.</p>
<p>In order to achieve that you will have to write your own JMXMP connector client provider (e.g. service:jmx:<b>secure-jmxmp</b>://host:port) that initializes the environment map with the appropriate security settings and then rewrites the JMXServiceURL to service:jmx:<b>jmxmp</b>://host:port and delegates to the existing JMXMP connector client provider.</p>
<p>Of course, you will have to supply the javax.net.ssl.* SSL system properties in the command-line as you already do.</p>
<p>Have a look at the JMX class JMXConnectorProvider for more detailed info.</p>
<p>Regards,<br>
Luis-Miguel Alventosa<br>
Java SE JMX/JConsole development team<br>
Sun Microsystems, Inc<br></p> -
Problem connecting to public wifi hotspot using ibook and airport
Hi
I have a brand new iBook G4, replacing an iBook G3. At home I use it to connect wirelessly or wired with my Netgear router. No problems.
Yesterday I tried to access a public, unsecured wifi hotspot in a local cafe. There were two other people there using the net, both using iBooks (high Mac density, it seems!).
Whatever I did, I simply couldn't connect. First, using the same Location I use at home (defined to only use Airport), I could see the named network, but when I selected it I got the 'could not connect' dialog. Retried, no luck.
I then created a new location, configured that to use Airport. Same problem.
I then created a new network name, and tried again. No luck. Using this last option, it actually asked me for a WEP password, even though the network was, in fact, unsecured, and the other users had not been asked this.
I do use WEP protection at home.
Any ideas?? I'd like to be mobile and networked, so I'd really like to fix this!I presume that the iBook G3 worked fine at the location previously?
Some 802.11b access points require a firmware upgrade before 802.11g (Extreme) clients can connect.
Though 802.11g is backward compatible with 802.11b some older access points were developed before 802.11g and therefore are not in a position to allow the 802.11g clients to connect.
Note that you can attempt to persuade an Airport Extreme client to operate in 802.11b mode.
Hold down the control key [ctrl] when selecting the network from the menu.
http://docs.info.apple.com/article.html?artnum=107938
iFelix
Maybe you are looking for
-
Handling flat file destinations dynamically
After performing a join operation on two tables i get the below resultset pid, fname, typename, pname, pcost 1, cad, bars, product-1, 100 2, har, witte, product-2, 120 3, nes, bars, product-3, 119 Now i need to create files with the obtained resultse
-
Hi All, The Transformation Guide of OWB mentions that DECODE, CASE can be used. But I am unable to find either of these functions in the Expression Builder. Can you please tell me wher should I search for these functions, or if you could tell me if t
-
Satellite L650-1PE - Error messages in Toshiba bulletin board
I got error messages when i try to use Toshiba bulletin board, so firstly I got error 3 and then i press ok and i got error 23 which i don't know why? By the way, my laptop Satellite L650-1PE. Also I uninstalled it and reinstall the latest version ag
-
Hello, We have 2 instances of ABAP and Java engines on XI server. When I send a request to Instance 02 of Java engine, the request is forwarded to 01 instance of ABAP engine and gets processed there. We have defined local bundle setting in visual adm
-
Hi, im from Spain and maybe my english is bad. I just recieved my new Time Capsule 1Tb last generation. I have a router 3com 812 without DHCP, so i connected my TC to my router in the WAN slot. I opened Airport Utility and change the options. I used